CAR ESC by qingyunliuliu

VIEWS: 4 PAGES: 3

									            ™
       SUPPO™ Speed Controller Programming Instructions

                                       Surface ESC
Features:
Voltage: 4.8V-15V, 4-12Nimh or 2-4Lipo;
Low internal resistance: 0.003MR(30A), 0.002MR (50A), 0.0007MR (100A)
Voltage protection 3.0V each cell of Lipo
Constant current: 30A, burst 50A
PWM: 8k/16k/32k
Support most brushless motor
Max RPM 30000 for 14poles motor
Water proof
BEC 5V/2A, burst 3S support digital servo
Proportional break
Reverse with proportional power



Throttle neutral position study
       1.     Connect your motor and receiver to the speed controller, but do not connect the
              battery yet.
       2.     Turn on your transmitter and move the throttle stick to the FORWARD MAX
              THROTTLE position (full up).
       3.     Connect your battery and you will hear the initial musical tones. If you hear motor
              BEEP BEEP, your need to Reverse the Throttle position to Max until you hear the
              musical tones.
       4.     Then release the throttle, wait for BEEP BEEP ( Twice) to confirm neutral
              position.

Programming
·Phrases 1 Enter programming Mode
       5.     Connect your motor and receiver to the speed controller, but do not connect the
              battery yet.
       6.     Turn on your transmitter and move the throttle stick to the FORWAR MAX
              THROTTLE position (full up).
       7.     Connect your battery and you will hear the initial musical tone of programming
              mode.
·Phrases 2 Programming
    After 3 seconds, the motor will start beeping a sequence of tones – a musical tone followed
    by one or more beeps. Each sequence represents a parameter that you can program and is
    repeated 3 times. The parameters are:




                                               1
                                    Music Tone + 1         Options 1. Brake Setting
♪—
                                    Beep
                                    Music Tone + 2         Options 2. Reverse Setting
♪— —
                                    Beeps
                                    Music Tone + 3         Options 3. Acceleration
♪— — —
                                    Beeps
                                    Music Tone + 4         Options 4.Battery type
♪— — — —
                                    Beeps
                                    Music Tone + 5         Options 5. Timing Mode
♪— — — — —
                                    Beeps
                                    Music Tone + 6         Option 6. PWM setting
♪—     —     —     —     — -
                                    Beeps


 Step 1. Starting, Enter Sub-optins. When you hear the sequence for the parameter you wish to
       program, move the throttle stick to the Center Position to Enter Sub-options.
       The motor will then start beeping a Morse code sequence of short and long beeps
       representing the possible options you may choose for the selected parameter. See table 2 for
       a list of all programmable options. Each option sequence is repeated 3 times.

 Step 2. Select and save, the select the option, move the throttle stick back to the
      Full-up-position., When you hear the sequence for the option you wish to select. The
      controller will then save the selected option, and sound a long beep as a confirmation. It
      then goes back to the beginning of the programming sequence (phrases 2).

 Step 3. Exit to main manual and reload programming. When complete programming, move
       the throttle stick to the Lowest (Down, reverse) Position. The controller will exit to main
       manual and re-initialize in normal running mode. The system is ready to run.




                                                 2
The table below summarizes the various programming options for each parameter:
Option 1. Brake Setting
   ♪—
• — 1 Short + 1 Long                          Light Brake (start when throttle on reverse
                                              position)
• — — 1 Short + 2 Long                        Soft Brake (start when throttle on neutral
                                              position)
• — — — 1 Short + 3 Long *                    Medium Brake *
• — — — — 1 Short + 4 Long                    Hard Brake
• — — — — —1 Short + 5 Long                   100% Brake



Option 2. Reverse ♪— —
•• — 2 Short + 1 Long                         No Reverse
•• — — 2 Short + 2 Long                       Reverse with 25% Power
•• — — — 2 Short + 3 Long                     Reverse with 50% Power
•• — — — — 2 Short + 4 Long                   Reverse with 100% Power*


Option 3. Accleration ♪— — —
••• — 3 Short + 1 Long *                      Soft acceleration *
••• — — 3 Short + 2 Long                      Medium acceleration
••• — — — 3 Short + 3 Long                    Hard acceleration



Option 4. Cell Type ♪— — — —
•••• — 4 Short + 1 Long                       NIMH/MICD * slow down on 75% of initial
                                              voltage (0.9v), cut-off at 70% of initial voltage
                                              (0.85v).
•••• — — 4 Short + 2 Long                     LIPO, Slow down at 3.0v per cell LIPO,
                                              Cut-off at 2.9V per cell LIPO


Option 5. Timing Mode Setting
♪— — — — —
••••• — 5 Short + 1 Long *                    0º - For 2-4 Pole Inrunner Motors *
••••• — — 5 Short + 2 Long                    3º - For 2-4 Pole Motors
••••• — — — 5 Short + 3 Long                  7º- For 6-8 Pole Motors
••••• — — — — 5 Short + 4 Long                15º- For 6-8 Pole Motors
••••• — — — — — 5 Short + 5 Long              22º - For 10-14 Pole Motors


Option 6.                                     Only Available for 50A above (50A, 70A,
Pulse Width Modulation(PWM) Setting           100A) version
♪— — — — — —
•••••• — 6 Short + 1 Long                     8KHz *
•••••• — — 6 Short + 2 Long                   16KHz
•••••• — — — 6 Short + 3 Long                 32KHz
 * is Default Setting
                                          3

								
To top