1942011pdf

Document Sample
1942011pdf Powered By Docstoc
					- - - - - - - - - - - - - - - - MATERIAL SAFETY DATA SHEET - - - - - - - - - - - - - - Micro-Gen
MANUFACTURER'S NAME: MICRO-GEN EQUIPMENT CORP. 10700 SENTINEL DRIVE SAN ANTONIO, TEXAS 78217 TEL: (210) 654-8570 HMIS RATING: HEALTH: 1 FLAMMABILITY: 2 REACTIVITY: 0 ----------------------------------------------------------SECTION I - PRODUCT IDENTIFICATION ----------------------------------------------------------PRODUCT NAME: ULD R-400+1 PRODUCT CODE: 05010-11 DATE ISSUED: 5/22/92 SUPERCEDES: 1/31/92 PREPARED BY: Richard Clark MICRO-GEN CHEMICAL INFORMATION: 1/800-777-8570 MEDICAL EMERGENCY (ONLY): 1/800-228-5635 ----------------------------------------------------------SECTION II - HAZARDOUS INGREDIENTS/IDENTITY INFORMATION ----------------------------------------------------------Ingredient/CAS Number Weight/% Exposure Limit ----------------------------------------------------------ACTIVE INGREDIENTS 4.00 None Resmethrin Established 10453-86-8 Related Compounds 0.545 Pyrethrin 1.00 5mg/m3 8003-34-7 ACGIH/OSHA/ TWA Piperonyl butoxide technical 5.00 None 51-03-6 Established INERT INGREDIENTS 89.455 200 ppm TLV Petroleum Distillate Exxon 64742-47-8 Recommended See Regulatory Information (Section IX) for explanation of bracketed information. ----------------------------------------------------------SECTION III - PHYSICAL/CHEMICAL CHARACTERISTICS ----------------------------------------------------------BOILING POINT 760 mmhg (deg F): 370 deg F Initial SPECIFIC GRAVITY (H2O = 1): 0.800 (H2O @ 25 deg C = 1.00) VAPOR PRESSURE (mmHg): NA VAPOR DENSITY (AIR = 1): NA SOLUBILITY IN WATER: Insoluble in water. MELTING POINT: NA EVAPORATION RATE (Butyl Acetate = 1): APPEARANCE AND ODOR: Clear brown solution - Characteristic odor (petroleum distillate) ----------------------------------------------------------SECTION IV - FIRE AND EXPLOSION HAZARD DATA ----------------------------------------------------------FLASH POINT (Method): 170 deg F (TCC) FLAMMABLE LIMITS: NA EXTINGUISHING MEDIA: Foam, dry chemical, CO2 SPECIAL FIRE FIGHTING PROCEDURES: NA UNUSUAL FIRE AND EXPLOSION HAZARDS: NA ----------------------------------------------------------SECTION V - REACTIVITY DATA ----------------------------------------------------------STABILITY: Stable CONDITIONS TO AVOID: INCOMPATIBILITY (Materials to Avoid): NA HAZARDOUS DECOMPOSITION OR BYPRODUCTS: CO2 and CO HAZARDOUS POLYMERIZATION: Will Not Occur CONDITIONS TO AVOID: Avoid excessive heat, ignition sources, and oxidizing agents.

ULD R-400+1
----------------------------------------------------------SECTION VI - HEALTH HAZARD DATA ----------------------------------------------------------ROUTE(S) OF ENTRY: INHALATION: X SKIN: X INGESTION: X CARCINOGENICITY: NTP: No IARC Monographs: No OSHA: No SIGNS AND SYMPTOMS OF EXPOSURE: Eye irritation, headache, nausea, and vomiting. EMERGENCY AND FIRST AID PROCEDURES: EYE: Flush with plenty of water. Get medical attention if irritation persists SKIN: Wash with plenty of soap and water. Get medical attention if irritation persists. INGESTION: Call a physician or Poison Control Center. Do not induce vomiting. This product contains petroleum solvent. Aspiration may be a hazard. ----------------------------------------------------------SECTION VII - PRECAUTIONS FOR SAFE HANDLING AND USE ----------------------------------------------------------STEPS TO BE TAKEN IN CASE MATERIAL IS RELEASED OR SPILLED: Extinguish all ignition sources. Absorb spilled material with an absorbent such as vermiculite or sand. WASTE DISPOSAL METHOD: Sweep up material and contain for disposal. Dispose of in accordance with all Federal, State and Local requirements. Do not reuse empty container. Destroy by perforating or crushing. CONTAINER DISPOSAL: One gallon and over, triple rinse and then offer for recycling or reconditioning. Keep out of water ways. PRECAUTIONS TO BE TAKEN IN HANDLING AND STORING: Keep out of the reach of children. Harmful if swallowed. Do not breath mist. Avoid unnecessary contact with liquid or mist. Do not store, pour or spill near heat or open flame. Avoid contamination of food or feedstuffs. OTHER PRECAUTIONS: Do not contaminate water by cleaning of equipment or disposal of waste water. ----------------------------------------------------------SECTION VIII - CONTROL MEASURES ----------------------------------------------------------RESPIRATORY PROTECTION (Specify Type): Approved for organic vapors and pesticides. NIOSH/MSHA approval No. TC 23C585. VENTILATION: General or local exhaust ventilation. PROTECTIVE GLOVES: Rubber EYE PROTECTION: Goggles or safety glasses OTHER PROTECTIVE CLOTHING OR EQUIPMENT: Boots or closed shoes, full legged plants and full-sleeved shirts. WORK/HYGIENIC PRACTICES: Wash face, arms and hands before eating or smoking. Wash contaminated clothing (separately) with soap and hot water before reuse. ----------------------------------------------------------SECTION IX - REGULATORY INFORMATION ----------------------------------------------------------PA - These ingredients are subject to the reporting requirements under the Pennsylvania Hazardous Substance List. NJ - These ingredients are subject to the reporting requirements under the New Jersey Right to Know Hazardous Substance List. MA - These ingredients are subject to the reporting requirements under the Massachusetts hazardous Substance List. There are no ingredients subject to the reporting requirements under California's Proposition 65.

Page 1 of 2

- - - - - - - - - - - - - - - - MATERIAL SAFETY DATA SHEET - - - - - - - - - - - - - - Micro-Gen
----------------------------------------------------------DISCLAIMER OF EXPRESSED AND IMPLIED WARRANTIES: Although reasonable care has been taken in the preparation of this document, we extend no warranties and make no representation as to the accuracy or completeness of the information contained therein, and assume no responsibility regarding the suitability of this information for the user's intended purposes or for the consequences of its use. Each individual should make a determination as to the suitability of the information for their particular purpose(s). A request has been made to the manufacturer to approve the contents of this material safety data sheet. Upon receipt a new MSDS will be made available. ----------------------------------------------------------COMPAS Code: 19420110

ULD R-400+1

Page 2 of 2


				
DOCUMENT INFO
Shared By:
Categories:
Tags:
Stats:
views:2
posted:8/12/2009
language:English
pages:2