Docstoc

How to Replace a Door Bottom / Sweep

Document Sample
How to Replace a Door Bottom / Sweep Powered By Docstoc
					http://www.allaboutdoors.com                                                        Published 1/12/2005


                             Replacing Door Sweeps & Bottoms
               For Questions or Concerns, please refer to All About Doors & Windows
                                  http://www.allaboutdoors.com

The Five Basic Types of Door Bottoms:




The Slide-On The easiest to install. Slide off the old sweep, slide on the new.

The Snap-In Can normally be installed without removing the door. They fit into a kerf cut in the
bottom of the door.

The Wrap-Around Easy to install and are adjustable but sometimes requires installing new holes in the
door.

The "L" Shape Screws to the inside surface of the door. Easy to install and adjust, but doesn't always
work well

The Staple-On Requires removing the door from the frame. This type of door bottom is generally
found on wood doors.

                             All About Doors & Windows    |   1901 Cherry St.
http://www.allaboutdoors.com                                                        Published 1/12/2005


Determine Type of Door Bottom or Sweep:

Steel and Fiberglass doors normally use the slide-on or snap-in type. Benchmark steel doors use a L-
shaped bottom. Peachtree bottoms are a heavy rubber that is fitted into the bottom of the door. Wood
doors are almost always a nail or staple-on type door sweep. The wrap-around and L-shaped door
bottoms are screwed into the inside surface of the door; if you remove the screws, the door bottom
comes off.


Slide-on Door Bottoms or Sweeps:

    1. Determine which door bottom is needed. The slide-on sweeps come in different designs.

    2. Remove the existing door bottom; most just slide off.

    3. Cut new sweep to length if needed. Slide on new door sweep.

    4. If door sweep fits too loosely, a spot of adhesive or caulk may be applied between the sweep
       and the bottom of the door.


Snap-in Door Bottoms or Sweeps:

    1. Determine which door bottom is needed. The snap-in door bottoms come in different designs,
       and sometimes even the heights of the door sweeps will vary. Most of these types of door
       bottoms have a single or double kerf cut in the bottom of the door for the sweep to lock into.
       The spacing of the kerfs vary and you will want to match profiles.

    2. Remove the existing door bottom. Most just pry off.

    3. Cut new door sweep to length if needed. Snap or push new door sweep onto bottom of door.

    4. If sweep fits too loosely, a spot of adhesive may be applied.


Wrap-Around or "L-Type" Door Bottoms or Sweeps:

    1. Determine which door bottom is needed. The wrap-around sweeps fit different thicknesses of
       doors. Most exterior doors are 1-3/4" thick. Some older homes have doors that are 1-3/8" up to
       2-1/4" thick.

    2. Remove the screws on the existing door bottom.

    3. Cut new door bottom to length if needed. Position new door bottom onto bottom of door.



                            All About Doors & Windows     |   1901 Cherry St.
http://www.allaboutdoors.com                                                              Published 1/12/2005

    4. Close door and adjust door bottom as needed to get the proper fit.

    5. Apply new screws to hold door bottom in place. Be careful not to fit the sweep too tightly. If
       there is too much pressure on the bulbs or fins it will wear out faster.


Staple-On Door Bottoms or Sweeps:

    1. Determine which door bottom is needed. The staple-on sweeps come in different designs, and
       even the heights of the door sweeps will vary. The goal is to match profiles and especially
       height.

    2. Remove the hinge pins from the door. Lay door on its edge. Be careful not to position the door
       where it can fall or become scratched.

    3. Cut new sweep to length if needed. Position new sweep onto bottom of door. Note: The staple-
       on door bottom may seal better if a small spot of adhesive or caulk is applied to the bottom of
       the door before installing. Use just enough to touch both surfaces.

    4. Staple from the center and work your way to both ends. This will reduce the likelihood of
       ripples forming in the door bottom when it is affixed to the door. It is also best if the staples are
       staggered to both the inside and outside of the door sweep.

    5. Re-install door. Note: If replacing door by yourself, be careful not to hurt yourself. Some wood
       doors are very heavy. The use of shims under the door may help with the alignment when
       connecting the hinges.




               The staff at All About Doors & Windows spends a considerable amount of time
               creating articles and providing quality parts and hardware. We know you can find
               many of these products elsewhere and we appreciate your business. We thank you for
               your time and hope you will continue being a satisfied customer.




                             All About Doors & Windows       |   1901 Cherry St.
.

				
DOCUMENT INFO
Description: How to Replace a Door Bottom / Sweep