Docstoc

CIVIL_INTERIOR_FURNITURE_ESTIMATE

Document Sample
CIVIL_INTERIOR_FURNITURE_ESTIMATE Powered By Docstoc
					                                                                                                      SHETGIRI and ASSOCIATES




       PROPOSED INTERIOR / FURNITURE / CIVIL WORK OF IDBI CAPITAL MARKET
            5th FLOOR MAFATLAL CENTER AT NARIMAN POINT , MUMBAI.

                                 Description                                Qty. Unit Rate   Amount
GENERAL NOTES: -
WOOD WORK:
All internal woodwork / Plywood shall be treated with antitermite
preservative. All internal framework shall be of Aluminium unless otherwise
specified as Teakwood. AII exposed edges of Plywood shall be fixed with
C.P. Teak Lipping of size as directed by Architect. AII Plywood shall be of
b.w.r grade/quality ( marine plywood) unless otherwise specified. The
skinning shall be in 12 mm thk Exterior Grade Particle Board unless
otherwise specified. All exposed veneer surfaces shall be finished with
melamine polish . The thickness of the veneer shall be 4.00mm & that of
laminate shall be 1.5mm thk. However if the same shall vary , no extra
charges are payable for the additional thickness. The approved veneer shall
be finished with natural melamine polish of minimum 2 coats to have desired
matt melamine finish where ever specified.
Rate for high partition to include the cost of framework above false ceiling as
required to fix the same to the ceiling slab. Measurement of Partition &
Panelling shall be limited upto 6" above False ceiling & no separate
payment shall be made for the work above 6". The item if executed for AC
purpose shall be measured in the relevant item. The partition shall be
measured including the door & the door frame & no seperate payment for
door shall be made. The rate shall be all inclusive of the necessary
hardware, fittings, fixtures, floor spring, door closers, hinges, handles, locks
for the door & including glass & finishing for the same. The rate shall be also
inclusive of pattas & bands including the necessary framing/ openings for
Electrical, Telephone & AC outlets.


PARTITIONS / PANELLING
General Specification for partition :-
Main frame -Aluminium sections of 16 Gauge mentioned are out of size
2"x2" Aluminium section verticals at minimum 1' 6"-2'-0" Centre-Centre
spacing approx. and 2" X 1" size Aluminium sections horizontal at 1' 6"-2-'0"
Centre-Centre spacing approx. Extra frame below slab soffit for conduit to
run above. All verticals shall be secured to the ceiling.




                                                                                                                           1
                                                                                                       SHETGIRI and ASSOCIATES




                                  Description                                Qty. Unit Rate   Amount
All the internal wood section if any including the inside skin shall receive
three coats of anti-termite treatment including skip ply internally.
SKIN: -12mm Exterior Grade Particle Board shall be screwed to frame work
on both sides with joints as shown or directed.

SKIRTING : In the same alignment, 3" high in 12mm thk Particle Board with
a groove finished with laminate / veneer as the case maybe, or as directed
by the Architect.
Finishing :-
VENEER:- 4mm thk natural venner with matching superior approved grade
to be fixed to the plywood having joints as shown or directed complete with
melamine polish finish.

LAMINATE:- Approved laminate shall be of 1.5 mm thick.




                                                                                                                            2
                                                                                                            SHETGIRI and ASSOCIATES




                                    Description                              Qty. Unit Rate        Amount
    Laminate shall be fixed on plywood skins with glue having grooves as
    shown or directed. Internal surfaces at specified places shall be 0.8 mm
    thick as directed by Architect.

1   FULL HT. DOUBLE SKIN PARTITION.
    Providing and fixing Full ht. double skin Partitions as per specifications
    including skirting, complete as per drawings and instructions complete in all
    respects.
    Main frame -2"x2" Aluminium section of 16 Gauge verticals at minimum 1' 6"-
    2'-0" Centre spacing approx and 2" X 1" size Aluminium sections horizontal
    at 1' 6"-2'-0" Centre spacing approx extra frame below slab soffit for conduit
    to run above. All verticals secured to ceiling. AII the internal wood sections if
    any including the inside skin shall receive three coats of anti - termite
    treatment.
    Skin:- Both side with 12mm thk Exterior Grade Particle Board screwed to
    frame work on both sides with joints as shown or directed.

    SKIRTING : In the same alignment, 3" high in 12mm thk Particle Board with
    a groove finished with laminate / veneer as the case maybe, or as directed
    by the Architect.
A   Finishing : Both side finished in 1.5 mm thk Laminate as shown or directed 180           Sft
    by Architect.

B   Finishing : Both side finished in with 4.0 mm thk approved veneer finished          20   Sft
    with melamine polish as shown or directed by Architect.


C   Finishing : One side finished in 1.5mm thk approved laminate & other with           20   Sft
    4mm thk approved veneer finished with melamine polish as shown or
    directed by Architect.




                                                                                                                                 3
                                                                                                                 SHETGIRI and ASSOCIATES




                                       Description                                     Qty. Unit Rate   Amount
D   Finishing : One side finished in 3.0 mm thk approved Aluminium Composite 170 Sft
    panel with 6.0 mm thk glass inlays & other finished with gypsum board with
    pop punning and acryllic emulsion paint finish of approved colour, texture
    and shade as directed by Architect. Please note that the design, details of
    the partition & ACP or other finishes to be used shall be the same as
    existing on site for the other areas for which the contractor shall visit the site
    prior to quoting. No excuses on account of non visiting and deviations of any
    nature shall be entertained

E   Same as above but with Partical board on one side of the main frame to be       50    Sft
    finished with 1.5mm thk approved laminate finish and the other side of the
    main frame to be finished with gypsum board, 12mm thk to be finished with
    approved acryllic emulsion paint as shown or directed by Architect including
    necessary grooves, skirting etc complete.




                                                                                                                                      4
                                                                                                           SHETGIRI and ASSOCIATES




                                 Description                           Qty. Unit Rate             Amount
2   FULL HIGHT SEMI GLAZED PARTITION.
    Providing & Fixing full height Semi-Glazed partition with folowing
    specifications
    Main frame - 2"x2" Aluminium section of 16 Gauge verticals, not exceed 1'
    6"-2'-0" centres and 2" X 1" size Aluminium sections horizontal at floor level /
    skirting ht, 3'-0" level and door height at 7'-0" level. AII the internal wood
    section including the inside skin shall receive three coats of anti-termite
    treatment.
    Skin:- Both sides of the main frame shall be finished with 12mm thk exterior
    grade Partical board screewed to the frame with joints as directed upto 3'0"
    level and from 7'0" level to the top upto false ceiling level and including 5.5
    mm thk. clear glass Straight / segmented with frosted film of approved make
    & design and drawing to be fixed with t.w moulding all around of approved
    size & design including grooves, mouldings etc complete as directed by
    Architect & as shown in the drawing.

    SKIRTING : In the same alignment, 3" high in 12mm thk Particle Board with
    a groove finished with laminate / veneer as the case maybe, or as directed
    by the Architect.


A   Finishing : One side finished in 1.5mm thk approved laminate & other with 350           Sft
    4mm thk approved veneer finished with melamine polish as shown or
    directed by Architect.

3   FULL HEIGHT FULLY GLAZED PARTITON
    Providing and erecting in position full height fully glazed partiton in 12mm       60   Sft
    thk. toughened glass fixed in 4"x2" t.w.members at end & intermediate
    support side verticals, top & bottom finished with approved 4mm thk veneer
    with melamine polish including frosted film of approved make, shade &
    design on the glass including sealing the joints with approved sealant to be
    errected at an angle to the horizontal floor slab including bevelled edges to
    the glass on all sides etc complete as directed by the Architect

4   PARTITION ABOVE FALSE CEILING.




                                                                                                                                5
                                                                                                          SHETGIRI and ASSOCIATES




                                    Description                                 Qty. Unit Rate   Amount
    Providing and extending frame works of full height partitions wherever 40        Sft
    directed and finishing with 12 mm thk Exterior Grade Particle Board on both
    sides and finishing the same with approved paint including insulating the
    same with approved insulating material upto soffit of beam or ceiling
    including properly anchoring the same making necessary cut-outs for AC
    ducts etc complete wherever directed.

5   PANELLING : -
A   Providing and fixing Wall & Column Panelling for the existing surfaces to be   50   Sft
    made out of 16 gauge Aluminium framework backing of size 2" X 1" at 1'6"
    to 2' c/c to be covered with 12mm thk exterior grade Partical board and
    finished with approved 4mm thk Veneer and melamine polish including
    skirting & band at top in the same alignment with a groove and including
    teakwood moulding of approved size as shown in detailed drawing or as
    directed by Architect

B   Providing and fixing Wall & Column Panelling for the existing surfaces to be 350    Sft
    made out of 16 gauge Aluminium framework backing of size 2" X 1" at 1'6"
    to 2' c/c to be covered with 12mm thk exterior grade Partical board and
    finished with approved 1.5mm thk laminate including skirting & band at top
    in the same alignment with a groove and including teakwood moulding of
    approved size as shown in detailed drawing or as directed by Architect


C   Providing and fixing Wall & Column Panelling for the existing surfaces to be 100    Sft
    made out of 16 gauge Aluminium framework backing of size 2" X 1" at 1'6"
    to 2' c/c to be covered with 12mm thk exterior grade Partical board and
    finished with approved interior grade ACP including skirting & band at top in
    the same alignment with a groove and including teakwood moulding of
    approved size including the necessary partical board / ply backing to match
    the level of other finishes such as veneer in required areas as shown in
    detailed drawing or as directed by Architect


6   MAIN DOOR :




                                                                                                                               6
                                                                                                           SHETGIRI and ASSOCIATES




                                   Description                                   Qty. Unit Rate   Amount
Providing & Errecting in poisition Fully glazed double leaf door & its side 23        Sft
fixed glass in 12 mm thk Toughened Glass on Patch fittings of the size 3'0"
X 7'0" each including top patch fitting, bottom patch fitting, patch lock, Floor
Spring of reputed manufacturer and S.S handle 600mm long, 30mm dia
including frosted film of approved make, shade & design on the glass. AlI
damages to the floor work to be reinstated without any extra cost including
the cost of other fittings & fixtures & necessary hardware, necessary holes,
joints to be sealed with silicone sealant complete in all respects etc as per
drawings and directions of Architect.




                                                                                                                                7
                                                                                                             SHETGIRI and ASSOCIATES




                                    Description                                    Qty. Unit Rate   Amount

7   FALSE CEILING
    General :
    The filler, paper tapes, finishes and primers suitable for Gypsum boards,
    shall be as per recommended practises of India Gypsum.
    Framework grid and suspenders shall be fixed to avoid fouling with services
    such as ducting, sprinklers, electricals fixtures, etc
    T.W. framing may be allowed in certain areas for the Gypsum Board ceiling
    with the approval of the Architect. The same should have three coats of fire
    resistant paint.
    Note: All the hardware such as fastners, hangers, suspenders, etc. required
    for erection of the false ceiling shall be of INDIA GYPSUM make. And
    approved by the Architect.


A   Metal frame False Ceiling of 12 mm thk. Gypsum Board including vertical 500         Sft
    drop panels.
    Ceiling section of 0.5mm thickness having curled wedge of 51.5 mm and
    two flanges of 26mm each with lips of 10.5mm at 450mm center to center.
    Connecting clips & 12.5 mm dry wall screws at 230 mm center to center.
    The metallic grid shall be installed as follows :
    The perimeter channel along the perimeter of the ceiling with screw fixed to
    brickwall / partition with the help of rawlplugs and screws.
    The intermediate channels shall be suspended from the ceiling with steel Gl
    hanger fixed to the slab soffit with Gl cleat and steel expanation
    fasteners.The intermediate channels shall be at 4'-0" centre to centre
    distance. section placed in a direction perpendicular to the intermediate
    The ceiling
    channel at 1'-6" C/C distance shall be fixed to the intermediate channel with
    the help of connecting clips and 12.5 mm dry wall screws at 230 mm centre
    to centre distance.




                                                                                                                                  8
                                                                                                        SHETGIRI and ASSOCIATES




                                  Description                                 Qty. Unit Rate   Amount
Finally, the 12mm thk. Gypsum boards shall be fixed to the metal frames
and the tapered/square edges of the boards shall be finished to a flush joint
with requisite filler, paper tapes, finisher and primer suitable for Gypsum
plaster boards, (as per recommendations of manufacturers, Indian Gypsum
or equivalent) including Acrylic Emulsion Paint of approved make and shade
and colour.
The rate shall include the cut-outs to be made for light fittings, grills,
diffusers, speakers, smoke detectors, sprinklers etc. with provision of the
frame along perimeter of the cut outs/ opening with channels/ ply to support
the ceiling adequately as per the directions of Architect. The rate shall
include necessary shapes, designs, patterns in curvature, sloping, dome,
oval& eliptical shaped etc including the necessary provisions of coved
lighting scheme etc complete as per the designs, drawings and instructions
of the Architect.




                                                                                                                             9
                                                                                                               SHETGIRI and ASSOCIATES




                                       Description                                   Qty. Unit Rate   Amount
B    FALSE CEILING (AMF)
     Providing and erecting false ceiling of Mineral Fiber ceiling Board AMF / 500 Sft
     Armstrong or equivalent make with framework, runners, cross runners &
     suspenders from the existing ceiling as per the manufacturers details and
     specification and 600X 600mmX 15mm thk tiles of approved design, texture
     & in microlook pattern including the grids in black / white silhoutte pattern,
     15mm as per manufacturers specifications complete including making
     necessary cut-outs for electrical fixtures, AC diffusers, access etc as per the
     instructions of the Architect.
     Approved Tile with black silhouette

C    Same as item no. 11A but finished with 4mm thk approved veneer &                  30   Sft
     melamine polish etc. complete as per instructions as per the design and
     instructions of the Architect..

D    Same as item no. 11A but finished with approved interior grade ACP                30   Sft
     complete as per instructions as per the design and drawing of the Architect..

8    Providing & Applying Plaster of Paris Punning up to average thickness of 200           Sft
     12 mm thk. on existing walls to proper level & plumb, including Groove
     Complete as per drawings & directions of the Architect.

9    Providing and erecting in position Plaster of Paris Cornices 4" x 4" in size      20   Rft
     to the false ceiling. Including filling the gaps with POP & painting the same
     with approved acryllic emulsion paint, colour as per instruction of Architect.

10   STAIN GLASS CEILING:
     Providing & errecting in position 10 mm thick stained glass in the ceiling with   10   Sft
     50x50 mm second class teak wood frame tounged & grooved in approved
     manner, polished with melamine polish and shall be suspended with
     hangers to take the load of complete system etc. complete.

11   Providing & Fixing Vertical Venetian Blinds 4" wide of' approved make, 150             Sft.
     shade, texture with supporting framework complete in working order as per
     manufacturers specifications & drawings & directions of the Architect.




                                                                                                                                   10
                                                                                                              SHETGIRI and ASSOCIATES




                                     Description                                    Qty. Unit Rate   Amount

12   FULL HEIGHT STORAGE
A    Providing and fixing Full height Storage of ht. 7'-0" and depth as specified
     in the drawings as per specification below.
     Skeleton - made out of 19 mm. thk marine ply at end verticals, top and
     bottom and verticals 450mm to 600mm Centres as shown in drawing and 6
     mm thk back marine ply.
     SHELVES - 19mm Thk. MarinePlywood top and edges finished in 0.8mm
     thk. Laminate to accommodate file height removable and supported on pins.
     SHUTTERS-made out of 19mm thk. Marine ply externally finished in 1.5mm
     thk. Laminate and Internally finished in 0.8 mm thk. Laminate as shown or
     directed.
     HINGES - Each shutter shall have 100mm long oxidised brass butt hinges.
     Mimimum 4 nos. hinges for each of the shutter for Full height Storage and 3
     Nos. hinges for each of the shutter for Low Height Storage to be provided.
     BOLTS - Flush tower bolts from inside at top and bottom to the shutters and
     magnetic catch fixed top and bottom.
     LOCKS - of approved make 4 -lever brass body dead lock with S.S. Key.




                                                                                                                                  11
                                                                                                            SHETGIRI and ASSOCIATES




                                     Description                              Qty. Unit Rate       Amount
     HANDLES - 100mm wide handles of c.p. brass as approved by the
     Architect. -As instructed by Architect, in plywood finished in Laminate.
     SKIRTING
     BACK - Back side of storage to have 6mm thk. Marine ply with polish finish.
     Finishing :- All external surface finish with 1.5 mm thk Laminate. All the         60   Sft
     exposed woodsurfaces shall be finished in melamine polish. In side visible
     surface complete with 0.8mm thk Laminate. Top to have tw moulding as
     instructed. All internal wood-work including back to have coat of anti termite
     of approved make before polishing.

13   DEMOLITION/DISMANTALING
     Demolishing/dismantaling of the existing Flooring, dado, partitions, ceiling, L.S.
     Platforms, counters, stone or brick work, bunds, walls, doors, windows, fans,
     lighting fixtures, cables & wires and any other material required for working
     on site & compliance of all the activities on site including removal of debris
     from site including shifting the same to a new desired place and re-fixing the
     same if desired under the instructions and directions of Architect.


14   WALL:
     Providing and erecting in position, level and plumb Siporex walls with table
     moulded perforated bricks of class designation 125 conforming to IS : 2222 -
     1991 in superstructure above plinth level upto ground and first floor level in
     mortar 1:6 ( 1 cement : 6 coarse sand ) etc. complete including both sides
     plaster finish. masonary wall
     115mm Sportex                                                                      25   Sft

15   PLASTERING.
     Providing and applying plaster to the walls in patches or long stretches in        50   Sft
     1:4 (I cement : 4 coarse sand) including water-proof chemicals of M/s
     Sunanda Chemicals, M/s Choksey Chemicals or equivalent approved make
     including Curing, scaffolding etc complete to the satisfaction of the Architect.


16   PAINTING :
     Note : The Rates for the Painting works shall be inclusive of three coats.
     The paint should be free from lead and Arsenic.




                                                                                                                                12
                                                                                                           SHETGIRI and ASSOCIATES




                                         Description                             Qty. Unit Rate   Amount
A   Painting of wall with minimum of 3 coats of Flat Oil Paint of approved shade 75   Sft
    & make on the wall, plywood or gypboard including all necessary surfaces
    preparation. The wall shall be cleaned, filled with putty & applied with one
    coat of primer so as to achieve a even surface to apply paint. As per the
    directions / to the satisfaction of the Architect / Engineer in charge.

B   Providing and applying acrylic aggregate textured wall coating in spectrum 100    Sft
    pigmented Ornaplast finish in any shade spray coat bubble or compact or
    rustik shade, maintaining material consumption rate of average 2.25 Kg. Per
    sq.mt. and 1.5mm thickness on new walls in the building.

C   Providing and applying Acrylic Emulsion Paint in minimum of three coats of 3500   Sft
    approved make and shade on Walls, Ceiling, plywood, gypsum board,
    surfaces etc including all the necessary surfaces preparation. The wall shall
    be cleaned, filled with putty & applied with one coat of primer so as to
    achieve a even surface to apply paint. As per the directions / to the
    satisfaction of the Architect /Engineer in charge.




                                                                                                                               13
                                                                                                            SHETGIRI and ASSOCIATES




                                       Description                                Qty. Unit Rate   Amount
17   FLUSH DOOR & SLIDING DOOR WITH FITTING.
     Providing and fixing 38mm thk water proof ready made solid flush doors 21         Sft
     for Toilets, cabins, ancillary areas specified to match the solid partitions
     including 2nd class BTC frame of 100 X 50mm finished with 1.5mm thk
     approved laminate finish on both sides including heavy duty floor springs,
     approved locks, handles, hinges, knobs etc. complete as per the directions
     of Architect.


18   FLOORING:
A    Providing and laying 9mm thk. Mirror finish approved Vitrified Tiles of 800           Sft
     approved make and shades of size 600x600x9mm thk (Min) laid in required
     pattern on avg. 25 to 30mm thk. bed of 1:4 cement mortar (1 cement : 4
     coarse sand) iun proper line and level including neat white cement float,
     filling joints with neat cement slurry, of appropriate colour, curing and
     cleaning complete.Tiles shall be free of any variation in colour or texture,
     and laying plastic sheet & 18mm thk. POP protective cover on flooring and
     removing when directed. The cost to include sealer treatment of Aqua mix
     brand. The rate shall be inclusive of application chemicals and Roffe.(Bassic
     rate of tiles = Rs. 60/Sqft.)


B    Providing and laying in position approved 18mm thk. Italian Marble flooring      60   Sft
     in sizes and pattern including inlays in dark coloured italian marble wherever
     specified as shown in the drawing over and including avg. 25 to 30mm thk.
     1:4 white cement mortar bedding, joints finished flush in matching colour
     cement, curing, rubbing, machine mirror grade polishing, washing, cleaning
     and sealer for anti-stain of Aqua mix brand etc. rate to include for chipping
     and leveling existing floor as required, complete and laying plastic sheet &
     18mm thk. POP protective cover on flooring and removing as per the
     directions of Architect .( Basic Rate of Italian Marble : Rs.400/- Sq.ft. ).
     Contractor to visit the site prior to quoting for this item

C    Providing and fixing 4" high skirting in required position on plaster of 1:3
     cement mortar for above flooring including moulding, rubbing, polishing for
     marble skirting. cement slurry, joints filled with white cement of appropriete
     colour, curing and cleaning complete.




                                                                                                                                14
                                                                   SHETGIRI and ASSOCIATES




                           Description   Qty. Unit Rate   Amount
1   Wooden t.w. skirting                 60   Rft




                                                                                       15
                                                                                                                    SHETGIRI and ASSOCIATES




                                          Description                                     Qty. Unit Rate   Amount
    19   GLASS BLOCK WALL.
A        Providing and erecting 7.5" glass block wall as per Architects choice, and 100        Sft
         manufacturers specifications including spacers, necessary adhesives,
         hardware etc complete.Make &design to decided by architect.

B        PANTRY COUNTER
         Providing and erecting pantry counter 2'-0" wide in kadappa undercarriage         5   Rtf
         of 11/2" thk. one side polished and top to be in 20mm thk. granite of
         mentioned shape & size. The counter to be supported with sandwitch
         cadappa verticals. The granite facia 4" & 6" to be fixed to verticals and top
         with edge polish and cutting for sink etc. complete as per instructions of the
         Architect including 4nos of S.S service trolleys below, Sink of approved
         make of size 24" X17" X8" and necessary plumbing fittings.
     20 PLUMBING WORK
         All plumbing and sanitary pipes to be "C" class G.I. Consealed in wall with L.S.
         bitumen treatment and covered with hessain cloth. All joints to be water tight
         and properly sealed. Drainage pipes shall be heavy duty ISI marked G.I. /
         P.V.C. pipes including all necessary high quality fitting such as bends, tees,
         flanges, elbows, coupling, reducer, unions, checknuts etc. joining with taflon
         tapes, excavation, refilling, consolidating where ever required.

    21   Providing and fixing Low height Storage of ht. 4'-0" and depth as specified      25   Sft
         in the drawings as per specification below.
         Skeleton - made out of 19 mm. thk Marine ply at end verticals, top and
         bottom and verticals 450mm to 600mm Centres as shown in drawing and 6
         mm thk back marine ply.
         SHELVES - 19mm Thk. Plywood top and edges finished in 0.8mm thk.
         Laminate to accommodate file height removable and supported on wooden
         1'x1/2' raftor.
         SHUTTERS-made out of 19mm thk. Marine ply externally finished in 1.5mm
         thk. Laminate and Internally finished in 0.8 mm thk. Laminate as shown or
         directed.




                                                                                                                                        16
                                                                                                          SHETGIRI and ASSOCIATES




                                     Description                                Qty. Unit Rate   Amount
    HINGES - Each shutter shall have 100mm long oxidised brass butt hinges.
    Mimimum 4 nos. hinges for each of the shutter for Full height Storage and 3
    Nos. hinges for each of the shutter for Low Height Storage to be provided.

    BOLTS - Flush tower bolts from inside at top and bottom to the shutters and
    magnetic catch fixed top and bottom.
    LOCKS - of approved make 4 -lever brass body dead lock with S.S. Key.
    HANDLES - 100mm wide handles of c.p. brass as approved by the
    Architect.
    SKIRTING -As instructed by Architect, in plywood finished in Laminate.
    BACK - Back side of storage to have 6mm thk. marine ply with polish finish.
    Finishing :- All external surface finish with 1.5 mm thk Laminate. All the
    exposed woodsurfaces shall be finished in melamine polish. In side visible
    surface complete with 0.8mm thk Laminate. Top to have tw moulding as
    instructed. All internal wood-work including back to have coat of anti termite
    of approved make before polishing.

B   Same as above but Low height storage finished with Veneer and melamine           15   Sft
    polish of approved shade and colour




                                                                                                                              17
                                                                                                               SHETGIRI and ASSOCIATES




                                       Description                                   Qty. Unit Rate   Amount
22A Providing & Fixing Low height Partition of about height 4'-0" to 4'-6" height 600 Sft
    to be erected in 2" X 2" Aluminium section of 16 Gauge verticals, not
    exceeding 1' 6" to 2' 0" centres and 2" X 1" size Aluminium sections
    horizontal at floor level / skirting ht, intermediate level & 3'-0" level with
    12mm. thk Exterior grade Partical Board skin on both sides of the frame to
    be screewed to the frame with joints as directed, including 10mm. glass with
    chamfered edges of 1'0" to 1'6" height, including approved frosted film of
    approved make & design on the glass including soft board panel with felt
    cloth on one side of the partition. The partical board skin to be finished with
    1.5mm thk. approved laminate with t.w. beading all throughout the exposed
    edges & periphery including fixing the glass, sealing all the joints, grooves in
    laminate, melamine polish to the mouldings & t.w members, complete as per
    the directions of Architect.

 B   Same as above but Low height Partition finished with approved 4mm thk         50   Sft
     veneer with melamine polish finish, complete as per drawing and as directed
     by the Architect.

23   Providing & Fixing Soft Board panelling over framework of 25 mm x 18 mm       50   Sft
     T.W. Frame at 600 mm c/c with 6mm Marine ply skining on top & 12mm thk.
     soft board with fabric finishing over ply. Complete as per drawings &
     directions of the Competent Authority, 25 mm x 12 mm T. W.Moulding on
     edges (Basic Price of fabric Rs.250/- meter).

24   STORAGE ON WALL / PARTITION.
     Providing and erecting in position storage cupboards 16" deep over the 225         Sft
     walls or the partitions to be made out of 19mm thk. Marine ply sides, top,
     shelf, and bottom with openable shutters including hinges, handles, ball
     catches, tower bolt, locks etc. complete finishing inside by natural polish as
     per the direction and with 1.5 mm thk approved laminate inside. The inner
     surfaces to be finished with natural polish as per instructions.




                                                                                                                                   18
                                                                                                             SHETGIRI and ASSOCIATES




                                      Description                                  Qty. Unit Rate   Amount
25   Providing and erecting in position Credenza provided with castors for the
     tables of 750mm height and 450mm deep or as instructed by the Architect to
     be made out of 19mm thk.Marine ply & having t.w. moulding all round with 2
     nos of drawers on top and openable or sliding shutters below. The openable
     shutters to be made out of 19mm thk. marine ply with all internal surfaces to
     be finished in 0.8 mm thk approved laminate and externally with 1.5mm thk
     laminate including brass hinges, ball catches, 100mm brass handles, brass
     locks etc. complete as per the instruction of the Architect.

A    Finished with approved laminate (1.5 mm externally & 0.8 mm internally)     25    Sft




                                                                                                                                 19
                                                                                                                   SHETGIRI and ASSOCIATES




                                       Description                                       Qty. Unit Rate   Amount

26   MANAGER / OFFICER TABLE .
     Providing and erecting in position Manager & Officer's work station cluster to       1   Nos
     be made out of 19mm thk.Marine ply for work top, a storage unit with two
     numbers of drawers of 4" depth on one side and a side credenza on the
     other side. The credenza shall be paid for seperately in the relevant item,
     and including a 50 X 38 mm t.w. moulding to be fixed to the edge of the
     table all around with keyboard drawers on ss telescopic channels. All the
     exposed surfaces shall be finished with approved 1.5mm thk laminate and
     internally with 0.8mm thk laminate including a CPU trolley, wire manager,
     s.s. fitting such as hinges, ball catches, locks etc. The rate shall be inclusive
     of a glass in front of the necessary height of a minimum of 2'-0" height and a
     necessary opening in the glass for transfer of papers. Necessary opening
     for electrical/computer switches, points & sockets shall be provided etc.
     complete as per the drawing. The Elevation of the table shall be as directed
     by Architect on site.

27   WORK STATIONS FOR (S.W.O.)
     Providing and erecting in position SWO's and Cash work station cluster to           17   Nos
     be made out of 19mm thk. Marine ply for work top, a storage unit with three
     numbers of drawers of 4" depth and the bottommost of the remaining height
     on one side and a single pencil drawer on the other side and including a 50
     X 38 mm t.w. moulding to be fixed to the edge of the table all around with
     keyboard drawers on ss telescopic channels. All the exposed surfaces shall
     be finished with approved 1.5mm thk laminate and internally with 0.8mm thk
     laminate including a CPU trolley, wire manager, s.s. fitting such as hinges,
     ball catches, locks etc. The rate shall be inclusive of a glass in front of the
     necessary height of a minimum of 2'-0" height and a necessary opening in
     the glass for transfer of papers. Necessary opening for electrical/computer
     switches, points & sockets shall be provided etc. complete as per the
     drawing. The Elevation of the table shall be as directed by Architect on site.




                                                                                                                                       20
                                                                                                                   SHETGIRI and ASSOCIATES




                                       Description                                       Qty. Unit Rate   Amount

28   Providing & Errecting in position, bevelled Glass dividers out of 10mm thk          50   Nos
     glass between the two workstations admeasuring approx 2''-3" X 1'-6" to be
     placed in position with the D-brackets including edging of the glass, etching /
     frosted film etc complete

29   WORKING COUNTER.( 2'-3" wide )
     Proving and fixing in position running working counter 2'-3" wide to be made        50   Rft
     out of 19mm thk. Marine ply for working top supported on 2" X 2" CP T.W.
     member at 2'-0" c/c. The counter shall have drawer unit with 3 nos of
     drawers and locakable key board drawer at every 3'-0" centre intervals. Rate
     shall be inclusive of providing and fixing of soft board upto 4' height with felt
     cloth between counter top and storage above including a 6" band in 19mm
     thk. commercial ply finished with 1.5mm thk laminate above the counter top
     for electrical switches. The overhead storage above of 18" depth in 19mm
     commercial ply finish with 1.5mm thk. laminate including adjustable shelves
     of 19mm thk. commercial ply to be finished in 0.8mm thk laminate. The
     counter shall have teak wood lipping as shown in the drawing. All the
     exposed surfaces of the counter & drawers shall be finished with 1.5mm thk.
     laminate and internally natural polish including s.s. locks, handles, ball
     catches, wire manager, hinges, channels etc. complete as ps. Stell has 15
     years of speaking




                                                                                                                                       21
                                                                                                            SHETGIRI and ASSOCIATES




                                     Description                                  Qty. Unit Rate   Amount
30   Providing & Supplying Sofa made out of T.W.Frameworkof 75 x 40mm for
     frame & arm rest under carriage and grid work.Inclusive of 100 mm thk in
     seat & 75 mm thk in back cushion of high density(30) Polyutherene foam,
     upholstered with fabric of approved shade & texture supported on springs /
     ply complete as directed. ( Basic cost of fabric Rs.-500 / mt.) as per
     following respective drawing including hand rest of etc finished as directed
     by Architect.

A    Two Seater Sofa                                                               2   No.

31   CHAIRS
     The right to select, omit or purchase of item is reserved with Engineer in
     charge
     The product specifications are as under :-
     Core Structure : Hot pressed wood bent ply in 12mm with T -Nuts embedded
     in to it for fixing of components
     Chair Seat: Pneumatic seat heiaht adjustment (16" to 25.5"). Chair padding
     should allow for distribution of weight to be at a maximum. The cushions of
     moulded, high density (45 units) polyurethane foam.
     Chair Back : Upper back support should be provided with tall back chairs.
     The chair back should make contact with individual's upper back and lumbar
     ( back ) support. Back and seat angle adjustment allow for neutral
     positioning : 90-120 degree trunk- thigh angle. Back tension adjustment.
     Variable back stop adjustment on back tilt mechanism with locks in place at
     various angles.The cushions of moulded, high density ( 45 units )
     polyurethane foam.
     UPHOLSTERY : Fabric finish. The upholstering to be done bv means of
     pneumatic gun. The back & seat edges to be covered by PVC profile which
     is also stapled or ABS fibre covers fitted on the back. The fabric shall be
     coated with scotch guard for stain resistance. Chair fabric should have
     elasticity that does not restrict the foam.
     Armrests : Fixed Handles of inflexible PUF with cushioned soft armrest and
     rounded edges.




                                                                                                                                22
                                                                                                           SHETGIRI and ASSOCIATES




                                     Description                                 Qty. Unit Rate   Amount
    Mechanism : Sinqle sprinq for full tilt or back tilt 360 deqrees swivel
    mechanisms with a locking lever. The carraige shall be fibre/metallic powder
    coated with five prong legs.(Synchro Gas Tilt)

    Castors : 5 flange or more star base. Twin wheel nylon castor each
    designed to sustain weight load of 100 Kg. Hard wheel castors for carpet
    and soft wheel castors for hard flooring.
A   Providing & supplying High height Chairs with Fabric finish as per above   1    No.
    specification : For Executives
B   Providing & supplying Medium Height Chairs with Fabric finish as per       37   No.
    above specification : For Conference
C   Providing & supplying Low height Chairs with Fabric finish as per above    5    No.
    specification: For Staff, Officers & Visitors




                                                                                                                               23
                                                                                                           SHETGIRI and ASSOCIATES




                                     Description                                Qty. Unit Rate    Amount
32   CORNER TABLE . ( 2'-0" x 2'-0" )
     Providing and supplying in position corner table to be made out of 2" x 2"  1   No.
     t.w. frame with 12mm thk. clear glass top with bevelled edges and etching
     with melamine polish etc. complete.


33   CENTER TABLE
     Providing and supplying in position center table to be made out of 2" x 2"       1    No.
     t.w. frame with 12mm thk. clear glass top with bevelled edges and etching
     with melamine polish etc. complete as instructed by Architect.

34   PLANTER BOXES. (18" X 18")
     Providing and supplying 18" dia decorative circular planter boxes to be
     made out of 19mm thk. ply to be finished from inside with paint, painted G.I.
     Tray as per the drawing and instructions of the Architect etc. complete.

     Finished with approved 1.5mm thk laminate                                        3    Nos.

35   ARTIFICAL PLANTS.
     Providing and supplying artificial plants approved by Architect, with moss       3    Nos.
     and necessary stand for holding the plants as per the approved sample.(The
     basic rate of Rs.1000/- for big size)

36   NOTICE BOARD.
     Providing and fixing notice board 4'-0" X 2'-0" to be made out of 19mm thk       1    Nos.
     Marine. ply with 3" deep with front glass shutter, 10mm thk. ply back
     covered with soft board and felt cloth including polishing locks etc. finished
     as per instruction of the Architect.

37   Providing and fixing White board with ceramic coating including soft board       20   Sft.
     with fabric of approved shade and design complete as per the specifications
     and directions of the competant authority.

38   ARTEFACTS :
A    Provision for Internal fountain in entrance lounge.




                                                                                                                               24
                                                                                                              SHETGIRI and ASSOCIATES




                                      Description                                   Qty. Unit Rate   Amount
B   Providing & fixing in position paintings / printed including decorative metalic
    frame to be obtained in consultation with Competent Authority.




                                                                                                                                  25
                                                                                                               SHETGIRI and ASSOCIATES




                                      Description                                    Qty. Unit Rate   Amount
                                                                                      1 Nos.
     Frame up 2'0" x 2'0" (basic rate : Rs.1500/-)                                    2 Nos.
     Frame up 6'0" x 3'0" (basic rate : Rs. 4500/-)                                   1   Nos.

39   TRAP DOOR.
     Providing and erecting in position trap door in 12mm thk Marine Plywood to      25   Sft
     house, A.C. ductable units to be made out of 2" x 11/2" t.w. frame with
     openable shutter in ply with necessary hinges, tower bolts, locks, painting
     etc. finished as per the instructions and design.

40   SUN CONTROL FILM.
     Providing and fixing reflective sun control film of approved make and shade 150      Sft.
     (Garware / Llumar or equivalent) to the glass complete as instructed by
     Architect

41   NAME PLATE:
     Providing Name Plate of size 375 X 150 mm in brass and fixing the same to        8   Nos
     the required positions.

42   WRITING DESK ( 3'-0" x 1'-3" )
     Providing and fixing in position writing shelf 1'-3" wide to be made in 19mm     1   Nos.
     thk.Marine ply top having 1" x 1" t.w. moulding with drawer for keeping slips
     and writing material for customer to be finished with approved veneer with
     melamine polish etc. complete as per direction.

     GRAND TOTAL




     FOR SHETGIRI & ASSOCIATES




                                                                                                                                   26

				
DOCUMENT INFO