VIEWS: 22 PAGES: 2 CATEGORY: Consumer Electronics POSTED ON: 8/2/2011
Enterprise is a new network television publicity, and media forms, that is, to upgrade the network video products, is based on integration of video and video (video PPT) as the carrier, with the form of network television, video programming and video integration with the form of PPT the company's products, image, culture, services, brands need to promote integration of content transmitted, so that customers can clearly see the actual companies, products and services.
1-1 Pull the center slide out until the rail is fully expanded. 1-4 Attach the rack mounts to either end of the rail assembly using the screws and nuts provided. ENTERPRISE TV SOLUTIONS Quick Start 1-2 You will see a black plastic tab where the center slide joins the rest of the rail assembly. Press this tab to the right to release the center slide. Remove 1-5 Install the rail assembly in your server rack using the screws provided. the slide from the rail assembly. 1 Rackmount the SnapStream Enterprise TV Server If your SnapStream Enterprise TV Server was provided with rackmount rails, install those rails on server unit and then install the SnapStream Enterprise TV Server in your server rack. If you have a tower case, proceed to step 2 1-3 Attach one center slide to each side of the Enterprise Server using the screws 1-6 Carefully lift the server and insert the ends of the center slides into the rail provided and the existing holes in the server chassis. The open ends of the slides assembly. The server should slide in and out smoothly on the rails. should face the rear of the server. 2 Connect TV Source (DirecTV) The following steps will be repeated for each STB, beginning with number 1 2-5 Use the S-video/audio cable labeled “1” and one RCA-to-1/8” adapter to Using the included cables, connect your DirecTV receiver to the SnapStream connect the STB to tuner card input number “1” on the Enterprise Server Enterprise TV Server. 2-3 Connect serial cable labeled “1” to serial port 1 on the multi port adapter. If a IMPORTANT: For each STB, the following numbers should match: single port USB serial adapter is provided, make sure that it is attached to the •The number on the serial port. 2-1 Connect the multi port USB serial adapter to a USB port on the back of the server. end of the serial cable. Connect the multi port adapter to power. Optional: Rackmount your multi port •The number on the serial cable. 2-4 Connect the serial cable to the STB labeled “1”. •The number on the STB. adapter. •The number on the S-video cable. 2-2 Label each of your set-top boxes (STBs) with a number: 1, 2, 3, 4, etc. •The number of the tuner card input. 2-6 Repeat steps 2-3 through 2-5 for all remaining set-top boxes. 1 Note: DirecTV set-top box not included 2 1/8” Adapter 2-2 DirecTV Receiver with SnapStream Enterprise TV Server. 1 S-Video & Audio Cables 2-4 2-5 Single port USB Serial Adapter AC Adapter Multi port USB Serial Adapter 1 1 &2 3 &4 5 &6 7 &8 9 & 10 2-3 USB Cable 2-1 Serial Cable 3 4 Connect Power Connect Network Connect the server’s power cable to a 120V power source. Connect the SnapStream Enterprise TV Server into the appropriate network router or switch using the supplied RJ-45 network cable. 5 Connect Keyboard, Monitor, Mouse and Speakers Connect a keyboard, a monitor, a mouse and speakers to the corresponding connectors on the SnapStream Enterprise TV Server for initial testing. (not included) (not included) 6 7 Boot up SnapStream Enterprise TV Server Install SnapStream Link Once you have completed all of the installation steps above, boot up the Install a SnapStream Link client on any PC on the local SnapStream Enterprise TV Server. network to give it access to the SnapStream Server. Rackmount Case Tower Case Finished!
Pages to are hidden for
"Quick Start"Please download to view full document