Docstoc

installation of wooden floors Products for the installation of

Document Sample
installation of wooden floors Products for the installation of Powered By Docstoc
					                         oors
                  e en fl
                th od
             forwo
          ts of
        ucon
    odati
  Pr ll
insta
     Parquet Line

     Over the last few years, there has been an increase in demand for wooden flooring in both the commercial and residential building
     sectors, for products of superior quality and which are aesthetically innovative. This demand has revolutionised the techniques
     and laying systems which, as far as MAPEI is concerned, has led to the development of a specific range of new products, made
     up not only of adhesives, but also by a complete range of products which includes binders, admixes and pre-blended mortars for
     mixing screeds, primers consolidators and waterproofing products for the preparation of high-strength substrates and smoothing
     and levelling compounds. The MAPEI systems used for laying wood are solvent-free and have an extremely low content of volatile
     organic compounds (VOC). Safe for those who use them, and for those who live them.

               Our commitment to the environment
               Since October 2005, the products in the ECO range, which had already been tested by internationally
                                                                                                                    ,
               recognised institutions such as the German TFI (Teppich Forschung Institute) and by the CRI (Carpet
                                                                                                                  dsds
               and Rug Institute), bear the “EMICODE EC 1 - very low emission level of volatile organic         ee
                                                                                                             crpoun
               compounds” mark, awarded by GEV (Gemeinschaft Emissionskontrollierte                         s
       GEV Verlegewerkstoffe, Klebstoffe und Bauprodukte e.V.), an association which
                                                                                                        for om es
                                                                                                      rs c v
   EMICODE®




                                                                                                   dehing dditi
               controls the emission levels of products for floors, and of which MAPEI is
     now an ordinary member.
                                                                                                Bin ot d a
                                                                                                  o
     Alongside the adhesive range, MAPEI also offers an extremely wide range of                sm an
     admixtures, pre-blended binders and mortars for screeds, primers, insulating materials,
     consolidators and anti-humidity barriers, as well as smoothing compounds and auxiliary
     products for the installation of long-lasting floors and resilient dressing materials.

     For further information about these products, take a look at the technical data sheets
     provided in folder No. 2 and from MAPEI internet address www.mapei.com.




                                                                                                 ▼   SELECTION TABLE OF
                                                                                                     MAPEI PRODUCTS FOR
                                                                                                     THE PREPARATION OF
                                                                                                     SCREEDS WITH SPECIAL
                                                                                                     BINDERS AND
                                                                                                     PRE-BLENDED MORTARS 3
                                                                                                 ▼




                                                                                                     PREPARATION OF
                                                                                                     SCREEDS
                                                                                                     Mapefluid N200               4
                                                                                                     Mapefluid PZ500              4
                                                                                                     Mapecem                      6
                                                                                                     Mapecem Pronto               6
                                                                                                     Topcem                       7
                                                                                                     Topcem Pronto                7
                                                                                                     Planicrete                   7
                                                                                                 ▼




                                                                                                     SELECTION TABLE OF
                                                                                                     MAPEI PRODUCTS FOR
                                                                                                     SMOOTHING
                                                                                                     COMPOUNDS                    8
                                                                                                 ▼




                                                                                                     SELF-LEVELLING
                                                                                                     SMOOTHING
                                                                                                     COMPOUNDS
                                                                                                     Ultraplan                   10
                                                                                                     Ultraplan Eco               11
TEATRO ALLA SCALA - Milan - Italy                                                                    Ultraplan Maxi              11
Parquet laid using ULTRABOND P902 2K
on screeds prepared with TOPCEM and
                                                                                                     Fiberplan                   11
TOPCEM PRONTO
                                                                                                 ▼




                                                                                                     THIXOTROPIC
                                                                                                     SMOOTHING
                                                                                                     COMPOUNDS
                                                                                                     Nivorapid                   12
                                                                                                     Latex Plus                  13
                                                              n
                                                          ode g
                                                       wo orin
                                                    or lo
                                                es f te f
                                            esiv ina
                                         dhd lam
                                        A n                                        ls
                                         a                                      Too



                             rs,
                        primeidating
                erials, onsol arriers
            matrials, c ture b
        ing e         is
     ean g mat nd mo
   Cl tin
                                         ▼
                                             SELECTION TABLE OF
            sa                               MAPEI ADHESIVES FOR
  sulapound
in m
                                             THE INSTALLATION OF
                                             WOODEN FLOORS       26
  co                                                                     Trowels for levelling
                                         ▼



                                             WATER VINYL ADHESIVES       compounds                 38
                                             Adesilex LC/R      28       Trowels for adhesives     38
                                             Adesilex LC/RP     28       Carbide hygrometer        38
                                             Adesilex LC        29       Electronic hygrometer     39
                                             Adesivil D3        29       Gun for soft cartridges   39
                                                                         Gun for sealants          39
                                         ▼




                                             ADHESIVES BASED ON          Spiked roller             39
                                             RESINS IN ALCOHOL
                                             Adesilex PA        30
                                         ▼




                                             ONE-COMPONENT
    ▼




        SELECTION TABLE OF                   POLYURETHANE AND
        MAPEI PRODUCTS FOR                   TWO-COMPONENT
                                             EPOXY-POLYURETHANE                          s
                                                                                      ble ts
        THE PREPARATION OF
        SUBSTRATES         14                ADHESIVES
                                             Lignobond             32               ta c
                                                                              tion rodu
    ▼




        ADHESION PROMOTERS                   Ultrabond P902 2K     32
        Primer G          16                 Ultrabond P990 1K     34
                                                                           lec ei p
        Eco Prim T        17                 Ultrabond P997 1K T   34   Se ap
                                                                           M
                                                                        of
        Mapeprim SP       17                 Ultrabond Eco P992 1K 35
        Primer KL         18
        Primer 3296       18
        Livigum           19                                             FOR THE PREPARATION
                                                                         OF SCREEDS WITH
        Primer PA         19
                                                         or s
                                                      s frofile
                                                                         SPECIAL BINDERS AND
                                                                         PRE-BLENDED MORTARS 3
                                                    e
                                                 siv d p
   ▼




        PRIMERS, CONSOLIDATING
                                               e                         FOR SMOOTHING
                                             dh g an
        COMPOUNDS AND/OR
        MOISTURE BARRIERS                                                COMPOUNDS                  8
                                           A in
        Prosfas              20
                                             t                           FOR THE PREPARATION
        Primer PU60
        Thinner PU
                             20
                             20          skir                            OF SUBSTRATES       14

                                                                         FOR THE INSTALLATION
        Eco Prim PU 1K       21                                          OF WOODEN FLOORING 26
        Primer MF            22
        Primer EP            22
        Quartz 1.2           22
        Triblock P           23
    ▼




        SEALANTS
        Eporip                24
        Eporip Turbo          24

                                             Ultrabond Eco 575     36
    ▼




        CLEANING MATERIALS
                                             Ultrabond P990 1K     36
        Pulicol               25
                                             Ultrabond P997 1K T   37
        Cleaner L             25
        Cleaner H             25
 ALPHABETICAL INDEX OF PRODUCTS



Adesilex LC                29
Adesilex LC/R              28
Adesilex LC/RP             28   TOPCEM PRONTO AND MAPECEM
Adesilex PA                30   PRONTO ARE CE MARKED AND
Adesivil D3                29
Carbide hygrometer         38
                                CERTIFIED ACCORDING TO THE
Cleaner L                  25   EUROPEAN CLASSIFICATION FOR
Cleaner H                  25
Eco Prim PU 1K             21
                                PRE-BLENDED MORTARS FOR
Eco Prim T                 17   SCREEDS EN 13813
Electronic hygrometer      39
                                The new European Standard for pre-blended mortars for screeds
Eporip                     24   (EN 13813), “Screed material and floor screeds - Screed material -
Eporip Turbo               24   Properties and requirements”, has now become effective. This norm
Fiberplan                  11   allows to classify the pre-blended mortars on the basis of the nature
Gun for sealants           39   of the binders employed and on their physical and elasto-mechanical
Gun for soft-cartridges    39   characteristics.
Latex Plus                 13   In particular, the standard symbols illustrated here below have been
Lignobond                  32   adopted for TOPCEM PRONTO and MAPECEM PRONTO pre-blended
Livigum                    19   mortars, to indicate the following:
Mapecem                     6
Mapecem Pronto              6                    • screeds made using TOPCEM PRONTO, in
Mapefluid N200              4                      accordance with the indications contained in the
Mapefluid PZ500             4                      Technical Data Sheet, are class CT (cementitious
Mapeprim SP                17                      binder-based), C30 (compressive strength after
Nivorapid                  12                      28 days equal to at least 30 N/mm2), F6 (flexural
Planicrete                  7                      strength after 28 days equal to at least 6 N/mm2),
Primer 3296                18                      A1fl (reaction to fire class).
Primer EP                  22
Primer G                   16                    • screeds made using MAPECEM PRONTO, in
Primer KL                  18                      accordance with the indications contained in the
Primer MF                  22                      Technical Data Sheet, are class CT (cementitious
Primer PA                  19                      binder-based), C60 (compressive strength after
Primer PU60                20                      28 days equal to at least 60 N/mm2), F10 (flexural
Prosfas                    20                      strength after 28 days equal to at least 10 N/mm2),
Pulicol                    25                      A1fl (reaction to fire class).
Quartz 1.2                 22
Spiked roller              39   As with adhesives used for ceramic tiles, according to the European
Thinner PU                 20
                                Directive 89/106 for products used in construction work, it is also
Trowels for adhesives      38
                                obligatory to apply the CE mark on the packaging of pre-blended
                                mortars for screeds in order to favour free trade within the member
Trowels for levelling
compounds                  38   states of the European Community.
Topcem                      7   The CE mark on the packaging is a guarantee for the user that the
Topcem Pronto               7   manufacturer has respected the following directives:
Triblock P                 23   • the screed, if made according to the indications contained in the
Ultraplan                  10
                                  Technical Data Sheet, possesses the mechanical characteristics and
Ultraplan Eco              11
                                  belongs to the reaction to fire class indicated by the CE mark;
                                • the manufacturer has issued a signed Declaration of Compliance
Ultraplan Maxi             11
                                  (EC Declaration) certificate, with which they assume all responsibility
Ultrabond Eco 575          36
                                  regarding declaration of the CE mark;
Ultrabond Eco P992 1K      35
                                • with reference to the “Directive 89/106”, the manufacturer is obliged
Ultrabond P902 2K          32
                                  to carry out the same controls as indicated for the CE mark regarding
Ultrabond P990 1K       34/36
                                  adhesives for ceramic tiles.
Ultrabond P997 1K T     34/37
                                                               S E L E C T I O N TA B L E O F M A P E I

                         ble
                                                                             PRODUCTS FOR THE
                        a                                        P R E PA R AT I O N O F S C R E E D S
                    n tducts                                   WITH SPECIAL BINDERS AND

                 tio pro tion                                         P R E - B L E N D E D M O R TA R S

              lecpei ara ith
            Se Ma rep w
             of he p eeds and
                t
             or f scrnders tars
            f o            r
                  l bi d mo
               cia de                                       MAPEI BINDER OR PRE-BLENDED MORTAR

           spe len
              b
          pre-




                                                                                                                              Pronto
                                                                                                                           Mapecem
                                                                                                       Mapecem
                                                                                   Pronto
                                                            Topcem




                                                                                 Topcem




                                                                                                                              Pr
PREPARATION OF THE MIXTURE
                                                      To be mixed         To be mixed           To be mixed         To be mixed
                                                     (1 bag) with         (1 bag) only with     (1 bag) with        (1 bag) only
                                                     0-8 mm graded        water (1.7 litres)    Gravel 0-8 mm       with water
                                                     aggregate                                  or 0-8 mm graded    (2.1-2.3 litres)
                                                                                                aggregate
                                                     (140-160 kg) and                           (80-100 kg) and
                                                     water (10-12 kg)                           water (4-8 kg)

TYPE OF SCREED
Bonded
                                                     Application of       Application of        Application of      Application of
Preparation of the substrate                         slurry bond          slurry bond           slurry bond         slurry bond
                                                     coat:                coat: Planicrete:     coat: Planicrete:   coat: Planicrete:
                                                     Planicrete: H2O:     H2O: Topcem           H2O: Mapecem        H2O: Mapecem
                                                     Topcem = 1 : 1 : 3   Pronto = 1 : 1 : 12   1 : 1 : 2 or with   Pronto 1 : 1 : 8 or
                                                     or with Eporip       or with Eporip        Eporip              with Eporip
Thickness of the screed                              up to 3.5 cm         up to 3.5 cm          up to 3.5 cm        up to 3.5 cm

Un-bonded
Preparation of the substrate                         Laying of a polyethylene sheet overlapped at least 20 cm on joints, sealed with
                                                     adhesive tape and rounded along the perimeter.
                                                     Application along the perimeter and around columns (if any) of compressible
                                                     material, such as foamed polyester, in thicknesses not lower than 5 mm.

Thickness of the screed                              From 3.5 to 8 cm (for thicknesses higher than 8 cm, pour a light-weight
                                                     cementitious mixture over which the polyethylene sheet will be placed.
                                                     Make the screed at least 3.5 cm thick).

Floating
Minimum thickness of the screed                      At least 4 cm, reinforced with a mesh. The thickness of the screed varies
                                                     depending on insulating layer compressibility. For more details refer to the
                                                     MAPEI Technical Service and/or consult the “Installation of Screeds for Laying
                                                     Floors” Technical Notebook.

Heating
Addition of additive to the mixture                  no                   no                    no                  no

Waiting time for the startup cycle                   4d                   4d                    1d                  1d

Startup cycle                                        Switch on the heating on minimum temperature. Increase the temperature
                                                     5°C every day until reaching the temperature when in service.
                                                     Keep the temperature on the maximum for some days. Decrease the
                                                     temperature 5°C every day until the screed reaches 15°-18°C.

PERFORMANCES
Waiting time before installing wood and resilients   4d                   4d                    1d                  1d

Compressive strength after 28 days (N/mm2)           ≥ 30                 ≥ 30                  ≥ 45                ≥ 60


                                      N.B. - THIS TABLE IS MERELY INDICATIVE; FOR FURTHER INFORMATION,
                                             REFER TO THE TECHNICAL DATA SHEET FOR EACH PRODUCT
           n
        tio s
    ara ed                                                     id
                                                            flu 00
 rep cre
P s                                                       e
                                                        ap PZ5
 of                                                    M

                id
            eflu 00
         Map N2

                                                  Superplasticising admixture with
                                                  pozzolanic effect for high quality and
                                                  chemical resistant mortars and
                                                  concrete.

                                                  Where to use:
                                                  Mapefluid PZ500 can be used for
                                                  manufacturing no-slump concrete for
                                                  screeds, by just reducing the w/c ratio,
                                                  therefore reducing the drying time.
                                                  Mapefluid PZ500 improves all properties
                                                  of the concrete.
   Superplasticiser for concrete.
                                                  It provides higher mechanical strength,
                                                  better waterproofing and durability.
   Where to use:
                                                  Mapefluid PZ500 must be added to the
   Mapefluid N200 can be used for
                                                  dry components of the mix (cement and
   manufacturing no-slump concrete for
                                                  aggregate), mixed until completely
   screeds, by just reducing the w/c ratio,
                                                  homogeneous and then mixed with water.
   therefore reducing the drying time.
                                                  The Mapefluid PZ500 mix is placed and
   Mapefluid N200 is a brown-coloured liquid
                                                  worked like normal concrete.
   admixture with a base of active polymers in
   water solution that disperse cement grains.
                                                  Consumption
   Add Mapefluid N200 directly to the
                                                  20-60 kg per m3 of the mix.
   mixture after all the other ingredients
   (cement, aggregates, water).
                                                  Packaging
   Mapefluid N200 can also be diluted into
                                                  11 kg bags. Big bags are available on
   the mixing water beforehand, but its
                                                  request.
   superplasticising action is less effective.

   Consumption
   0.5-1.5 kg per 100 kg of cement (0.4-1.3 l).

   Packaging
   200 l, 25 and 10 kg drums.
   1000 l tanks. Also available in bulk on
   request.

                                                                                EN 934-2
                                                                                T 3.1-3.2-9




                                EN 934-2
                                T 3.1-3.2
BINDERS FOR SCREEDS, SMOOTHING
       COMPOUNDS AND ADDITIVES



                            5
                                                               m
                 m                                         e ce to
6
              ece                                       Map Pron
           Map




                                                   Ready-to-use pre-blended mortar for
                                                   fast-setting and drying (24 hours)
                                                   screeds with controlled shrinkage.
    Special hydraulic binder for the
    preparation of rapid setting and               Where to use:
    drying (24 hours) screeds with                 Formation of both floating and bonded
    controlled shrinkage.                          screeds on existing and new slabs for the
                                                   installation of wood, PVC, linoleum,
    Where to use:                                  carpeting, rubber or any other type of
    Formation of floating and bonded screeds       flooring where fast drying or immediate
    on both existing and new slabs for the         laying is required.
    installation of floors that are moisture       Mapecem Pronto is ready-to-use and
    sensitive (wood, PVC, linoleum, carpeting,     must be mixed just with water.
    rubber) or any other type of flooring where    Mapecem Pronto is the ideal solution
    rapid drying and immediate laying is           where good quality graded aggregate is
    required.                                      hard to find or for job sites such as those
    Mapecem must always be mixed with              in city centres where the logistics involved
    aggregates. Bonded screeds (less than          in mixing conventional binders can be
    3.5 cm thick) and patching require the         difficult. Bonded screeds and patching
    application of a Mapecem and Planicrete        (thicknesses less than 3.5 cm) require the
    anchoring slurry. For floating screeds (at     application of a Mapecem Pronto and
    least 3.5 cm thick) lay a polyethylene sheet   Planicrete anchoring slurry. Floating
    beforehand; for thicknesses of 4-5 cm the      screeds (thicknesses above 3.5 cm) must
    aggregates must be graded from 0 to 8 mm       be laid over a polyethylene sheet.
    in diameter.
                                                   Technical data:
    Technical data:                                Mixing ratio: one 25 kg bag of
    Recommended mixture ratio: 350 to              Mapecem Pronto with 2.1-2.3 litres of
    450 kg of Mapecem with 1 m3 of aggregate       water.
    or Gravel 0/8 mm and with 80-160 kg of         Open time of the mixture:
    water depending on the aggregate               20-30 minutes.
    moisture.                                      Application temperature range: from
    Open time of the mixture at +23°C:             +5°C to +35°C.
    20-30 minutes.                                 Set to light foot traffic: after 2-3 hours.
    Application temperature range:                 Waiting time before installation:
    from +5°C to +35°C.                            24 hours for resilients and wood.
    Set to light foot traffic: after 2-3 hours.    Residual moisture after 24 h:
    Waiting time before installation:              less than 2%.
    24 hours for resilients and wood.              Storage: 12 months.
    Residual moisture after 24 h.:
    less than 2%.                                  Consumption
    Storage: 12 months.                            20-25 kg/m2 per cm of thickness.
    Consumption                                    Packaging
    3.5-4.5 kg/m2 per cm of thickness.             25 kg bags.
    Packaging
    20 kg bags.




                                                                                 EN 13813
                                               BINDERS FOR SCREEDS, SMOOTHING
                                                      COMPOUNDS AND ADDITIVES



                                                            m
                                                          ce nto
                                                                                                                                              7


            ce
              m                                          p
                                                       To Pro                                             rete
         To
           p                                                                                           nic
                                                                                                    Pla




                                                Ready-to-use pre-blended mortar for
                                                fast-drying (4 days) normal setting
Special hydraulic binder for the                screeds with controlled shrinkage.
preparation of normal setting and fast                                                        Synthetic rubber latex for improving
drying (4 days) screeds with controlled         Where to use:                                 adhesion and mechanical strength of
shrinkage.                                      Formation of both floating and bonded         cementitious mortars.
                                                screeds on existing and new slabs for the
Where to use:                                   installation of floors that are moisture      Where to use:
Formation of both floating and bonded           sensitive (wood, PVC, linoleum, carpeting,    • Additive for cementitious smoothing
screeds on existing and new slabs for the       rubber etc.) or any other type of flooring      compounds. Additive for improving the
installation of wood, PVC, linoleum, rubber,    where fast drying and laying is required.       mechanical and adhesive strength of
carpeting or any other flooring where fast      Topcem Pronto is ready-to-use and must          cementitious mixes for screeds, renders,
drying and laying is required. Bonded           be mixed just with water.                       thin levelling mortars, etc.
screeds (less than 3.5 cm thick) and            Topcem Pronto is the ideal solution where     • Additive for the preparation of cement
patching require the application of a           good quality graded aggregate is hard to        based slurries to form bonded screeds,
Topcem and Planicrete anchoring slurry.         find or for job sites such as those in city     for filling depressions and repairing parts
For floating screeds (at least 3.5 cm thick)    centres where the logistics involved in         of screeds, cementitious floors etc.
lay a polyethylene sheet beforehand; for        mixing conventional binders can be            • Additive for spatterdash to provide
thicknesses of 4-5 cm the aggregates must       difficult. Bonded screeds and patching          adhesion key for renders.
be graded from 0 to 8 mm in diameter.           (thicknesses less than 3.5 cm) require the    Do not use pure Planicrete as a primer or
                                                application of a Topcem Pronto and            slurry, always mix it with Portland cement,
Technical data:                                 Planicrete anchoring slurry. Floating         or, when required, with Mapecem or
Recommended mixture ratio: 200 to               screeds (thicknesses above 3.5 cm) must       Topcem.
250 kg of Topcem with 1 m3 of aggregate         be laid over a polyethylene sheet.
(diameter from 0 to 8 mm) and with                                                            Technical data:
120-140 kg of water for dry aggregate.          Technical data:                               Consistency: liquid.
Open time of the mixture:                       Mixing ratio: one 25 kg bag of                Colour: greenish white.
40 to 60 minutes.                               Topcem Pronto with 1.7 l of water.            Flammability: no.
Application temperature range: from             Open time of the mixture: 40-60’.             Application temperature range:
+5°C to +35°C.                                  Application temperature range:                from +5°C to +40°C.
Set to light foot traffic: after 12 hours.      from +5°C to +35°C.                           Storage: 12 months.
Waiting time before installation:               Set to light foot traffic: after 12 hours.
4 days for resilients and wood.                 Waiting time before installation:             Consumption
Residual moisture after 4 days:                 4 days for resilients and wood.               depending on dilution and thickness of the
less than 2%.                                   Residual moisture after 4 days:               mortar.
Storage: 12 months.                             less than 2%.
                                                Storage: 12 months.                           Packaging
Consumption                                                                                   25 - 10 - 5 - 1 kg drums.
2-2.5 kg/m2 per cm of thickness.                Consumption
                                                18-20 kg/m2 per cm of thickness in relation
Packaging                                       to the degree of compaction.
20 kg bags.
                                                Packaging
                                                25 kg bags.




                                                                                EN 13813
                    able
                 nt
            ectio    cts
         Sel      oduing
                pr h
            peimoot nds
         Ma r s pou
       of fo m
             co
                                                                                                  SMOOTHING COMPOUNDS




                                                                                                                                                    Latex Plus
                                                                                                                   Maxi




                                                                                                                                                    Nivorapid
                                                                                                                                        Nivorapid
                                                                                                                            Fiberplan
                                                                                                              Ultraplan
                                                                                                  Ultraplan
                                                                                      Ultraplan


                                                                                                       Eco
            Substrates
Cementitious screeds
MAPECEM, MAPECEM PRONTO, TOPCEM, TOPCEM PRONTO* screeds
Concrete structures
Anhydrite screeds
Heating screeds
Metal and wood surfaces
Terrazzo, ceramic


KEY                     This symbol is used to identify MAPEI products which give off a
                        low level of volatile organic compounds (VOC) as certified by GEV
                                                                                                                          MAPEI recommended
                        (Gemeinschaft Emissionskontrollierte Verlegewerkstoffe, Klebstoffe
                        und Bauprodukte e.V.), an international organisation for controlling
                        the level of emissions from products used for floors.



                       N.B. - THIS TABLE IS MERELY INDICATIVE; FOR FURTHER INFORMATION,
                              REFER TO THE TECHNICAL DATA SHEET FOR EACH PRODUCT

                       ●   Recommended by MAPEI
                       ■   Recommended by MAPEI. A first coat of Primer G (according to the instructions on the
                           technical data sheet) diluted 1 : 1 with water is recommended
                       ▲   For use only when a coat of Primer G or Eco Prim T is applied beforehand
                       ✚   Only on wood when a coat of Mapeprim SP or Mapeprim 1K is applied beforehand
                       ◆   Only for the preparation of substrates before installing wooden floating flooring
                       ✽   Recommended by MAPEI. A first coat of Eco Prim T or Mapeprim SP is recommended
S E L E C T I O N TA B L E O F M A P E I P R O D U C T S
                 FOR SMOOTHING COMPOUNDS



                                                     9
                   g
10
               lling
           evehin
       lf-l oot ds
     Se m un
       s po
      com              n
                    pla
                  Ultra




           Ultra-fast hardening (12 hours) self-
           levelling smoothing compound for
           thicknesses from 1 to 10 mm.

           Where to use:
           • Interior levelling of new or existing
             substrates, as long as they are not
             subject to rising damp, to make them
             ready to receive all types of flooring
             where a high resistance to traffic and
             loads is required.
           • Levelling existing flooring as long as they
             are solid, dry and clean.
           Ultraplan is applied up to 10 mm thick per
           coat. The minimum thickness of Ultraplan
           must be 3 mm when a wooden floor is
           going to be installed.

           Technical data:
           Consistency: fine powder.
           Colour: pinkish-grey.
           Pot life: 20-30 minutes.
           Setting time: 45-60 minutes.
           Set to light foot traffic: 3 hours.
           Waiting time before installation:
           12 hours.
           Application temperature range:
           from +5°C to +30°C.
           Mixing ratio: 25-26 parts water for
           100 parts by weight of Ultraplan.
           Storage: 12 months.
           Application: with a flat trowel and a pump.

           Consumption
           1.6 kg/m2 per mm of thickness.

           Packaging
           23 kg bags.
                                         BINDERS FOR SCREEDS, SMOOTHING
                                                COMPOUNDS AND ADDITIVES


               n
            pla o
        ltra Ec
                                                                                                                                                11

       U
                                                                                                             lan
                                                                                                          erp
                                                          planxi                                       Fib
                                                     Ultra Ma

Ultra-fast hardening (12 hours)
self-levelling smoothing compound for
thicknesses from 1 to 10 mm, with
very low emission of volatile organic
compounds (VOC).

Where to use:
• Interior levelling of new or existing                                                         Fibre-reinforced ultra-fast hardening
  substrates, as long as they are not                                                           (12-24 hours) self-levelling smoothing
  subject to rising damp, to make them                                                          compound for thicknesses from 3 to
  ready to receive all types of flooring                                                        10 mm.
  where a high resistance to traffic and        Ultra-fast hardening self-levelling
  loads is required.                            smoothing compound for thicknesses
                                                from 3 to 30 mm.                                Where to use:
• Levelling existing flooring as long as they                                                   Interior smoothing of existing and new
  are solid, dry and clean.                                                                     wooden flooring, wooden boarding, chip-
Ultraplan Eco is applied with a trowel or       Where to use:
                                                • Interior levelling of new or existing         board panels, ply-wood, that are sufficiently
with a pump up to 10 mm thick per coat.                                                         anchored and where a good resistance to
The minimum thickness of Ultraplan Eco            substrates, as long as they are not
                                                  subject to rising damp, to make them          loads and traffic is required.
must be 3 mm when a wooden floor is                                                             Levelling cement, terrazzo, existing ceramic
going to be installed.                            ready to receive all types of flooring
                                                  where high mechanical strength is             tile and natural stone substrates.
Technical data:                                   required.
                                                • Levelling existing flooring as long as they   Technical data:
Consistency: fine powder.                                                                       Consistency: fine powder.
Colour: pinkish-grey.                             are solid, dry and clean.
                                                Ultraplan Maxi is applied from 3 to 30 mm       Colour: pinkish-grey.
Pot life: 20-30 minutes.                                                                        Pot life: 20-30 minutes.
Setting time: 45-60 minutes.                    per coat.
                                                                                                Setting time: 45-60 minutes.
Set to light foot traffic: 3 hours.                                                             Set to light foot traffic: 3 hours.
Waiting time before installation:               Technical data:
                                                Consistency: fine powder.                       Waiting time before installation:
12 hours.                                                                                       12-24 hours.
Application temperature range:                  Colour: grey.
                                                Pot life: 30-40 minutes.                        Application temperature range:
from +5°C to +30°C.                                                                             from +5°C to +30°C.
Mixing ratio: 24-25 parts water for             Setting time: 60-90 minutes.
                                                Set to light foot traffic: approx. 3 hours.     Mixing ratio: 24-26 parts water for
100 parts by weight of Ultraplan Eco.                                                           100 parts by weight of Fiberplan.
EMICODE: EC 1 - very low emission.              Waiting time before installation:
                                                24-72 hours, depending on thickness and         Storage: 12 months.
Storage: 12 months.                                                                             Application: flat trowel.
Application: with a flat trowel and a pump.     temperature.
                                                Application temperature range:
                                                from +5°C to +30°C.                             Consumption
Consumption                                                                                     1.5 kg/m2 per mm of thickness.
1.6 kg/m2 per mm of thickness.                  Mixing ratio: 18-19 parts water for
                                                100 parts by weight of Ultraplan Maxi.
                                                Storage: 12 months.                             Packaging
Packaging                                                                                       25 kg bags.
23 kg bags.                                     Application: with a flat trowel and a pump.

                                                Consumption
                                                1.7 kg/m2 per mm of thickness.

                                                Packaging
                                                25 kg bags.
                                 id
                               ap
             pic            vo
                              r
          troing          Ni
12

         o
      hix oth s
     T o
       m ound
      s p
     com

                   Ultra-fast setting thixotropic
                   cementitious levelling mortar for
                   horizontal or vertical surfaces for
                   thicknesses from 1 to 20 mm.

                   Where to use:
                   Interior smoothing of all substrates
                   normally used in the building industry as
                   long as they are not subject to moisture
                   and are clean, such as:
                   • concrete slabs and walls, masonry,
                      renders and cementitious screeds, etc.;
                   • also suitable for existing floor and wall
                      ceramic tile, natural stone and terrazzo
                      coverings;
                   • suitable for repairing or levelling steps,
                      edges of pillars, depressions and holes in
                      flooring, walls and ceilings. Especially
                      recommended when the substrates need
                      to be covered within a short time.
                   It is applied from 1 to 20 mm per coat.
                   For installing wooden floorings the
                   minimum thichness required is at least
                   3 mm.

                   Technical data:
                   Consistency: fine powder.
                   Colour: grey.
                   Pot life: 15 minutes.
                   Setting time: 15-25 minutes.
                   Set to light foot traffic: approximately
                   2 hours.
                   Waiting time before installation:
                   24 hours.
                   Application temperature range:
                   from +5°C to +35°C.
                   Mixing ratio: 21-23 parts in weight of
                   water for 100 parts of Nivorapid.
                   Storage: 12 months.
                   Application: flat trowel.

                   Consumption
                   1.6 kg/m2 per mm of thickness.

                   Packaging
                   25 kg bags.
BINDERS FOR SCREEDS, SMOOTHING
       COMPOUNDS AND ADDITIVES




                          lus
                                                               13

                         P
                     tex
                   La




              Admixture to be mixed with Nivorapid
              and Planipatch to improve the
              deformability and adhesion onto
              difficult surfaces.

              Where to use:
              Latex Plus mixed with Nivorapid or
              Planipatch produces a cementitious
              levelling compound with such flexibility and
              high bonding strength to be used in
              interiors for levelling highly deformable
              surfaces such as:
              • PVC, ceramic tiles, rubber linoleum,
                strong non-woven;
              • properly fixed wood plank flooring,
                chipboard, plywood;
              • metal substrates.
              Levelling compounds prepared with
              Nivorapid and Planipatch mixed with
              Latex Plus and applied in thicknesses from
              3 to 20 mm and from 0 to 10 mm are
              suitable to receive every type of resilient or
              textile flooring.

              Technical data:
              Consistency: liquid.
              Colour: white.
              Flammability: no
              Pot life: 20 minutes
              Setting time: 30 minutes.
              Set to light foot traffic: after 2 hours.
              Application temperature range:
              from +5°C to +30°C.
              Waiting time before bonding:
              12-24 hours.
              Mixing ratio: 8-8.5 kg of Latex Plus per
              25 kg bag of Nivorapid.
              Application: flat trowel.

              Consumption
              0.6 kg/m2 per mm of thickness.

              Packaging
              10 kg drums.
                      a ble
                   nt
                tio         s
            elec       uctn
           S        rod tio
                 ip a r
             M aperepa rates
          of he p ubst
         for t of s                                                                                                                                          PRIMER




                                                                                      Turbo
                                                                                      Turbo
                                                                                     or Eporip
                                                                           Repairing cracks with




                                                                                                                                                                         (4)
                                                                                                                                                         Primer PU60
                                                                                                    (1)




                                                                                                                                                         Primer EP (4)
                                                                                                                                    (3)




                                                                                                                                                                                     (5)
                                                                                                                         (2) (6)




                                                                                                                                                         Eco Prim (4)

                                                                                                                                                                         Primer MF
                                                                                                                 (2)
                                                                                                   Primer KL




                                                                                                                                                                                     Triblock P
                                                                                                                                          PA




                                                                                                                                                            PU 1K
                                                                                                                                   Primer P




                                                                                                                                                                                      riblock
                                                                                                                        Livigum




                                                                                                                                               Prosfas
                                                                                                                                               Prosfas
                                                                                                                 3 96
                                                                                                                 3296
                                                                                                               Primer
                                                                                     Eporip
              Substrates
FLOORS
New
Cementitious screeds
MAPECEM, MAPECEM PRONTO, TOPCEM, TOPCEM PRONTO* screeds
Concrete floors
Anhydrite screeds
Heating screeds
Metal surfaces
Existing
Ceramic tiles, gres
Terrazzo, Palladiana
Natural stone
Concrete floors and screeds


LEGENDA                      This symbol is used to identify MAPEI products which give off a
                             low level of volatile organic compounds (VOC) as certified by GEV
                                                                                                                                                 MAPEI recommended
                             (Gemeinschaft Emissionskontrollierte Verlegewerkstoffe,
                             Klebstoffe und Bauprodukte e.V.), an international organisation for
                             controlling the level of emissions from products used for floors.



                                         N.B. - THIS TABLE IS MERELY INDICATIVE; FOR FURTHER INFORMATION,
                                                REFER TO THE TECHNICAL DATA SHEET FOR EACH PRODUCT


                                         *   Mapecem, Mapecem Pronto, Topcem, Topcem and Pronto screeds do not need any
                                             treatment against dust and they do not need consolidation as long as they have been
                                             prepared according to the suggestions on the relative technical data sheets.
                                         1) To be used exclusively with Lignobond and Ultrabond P902 2K
                                         2) Livigum diluted with water 1:4 - 1:5 and Primer 3296 diluted 1:1 - 1:2 to be applied
                                            on sound substrates that have slight surface dust before installing with vinyl adhesives
                                            (Adesilex LC, LC/R and LC/RP)
                                         3) Before the installation of wood with Adesilex PA
                                         4) For the consolidation of screeds whose surface is unsound and in the presence of
                                            residual damp above that accepted for the installation of wood before bonding wooden
                                            floors with Lignobond, Ultrabond P902 2K and Ultrabond P990 1K (N.B. Onto
                                            heating screed, Primer MF or Eco Prim PU 1K can be used only as a consolidating
                                            treatment).
                                         5) As a waterproofer of screeds with residual damp above that accepted for the
                                            installation of woodo
                                         6) As adhesion promoters before applying levelling compounds
                                      S E L E C T I O N TA B L E O F M A P E I P R O D U C T S
                                      F O R T H E P R E PA R AT I O N O F S U B S T R AT E S



                                                                                           15
                        (6)
            (6)



                        Mapeprim SP
(6)



           Eco Prim T
Primer G
             s ion
           he ters
16
 8

         Ad o
        prom
                    G
                mer
             Pri




     Synthetic resin based primer in water
     dispersion with very low emission of
     volatile organic compounds (VOC).

     Where to use:
     Treating gypsum or anhydrite surfaces prior
     to applying cementitious products. The
     surfaces to be treated must be clean and
     porous.
     Primer G should be diluted with water
     from 1:1 to 1:3 to protect old porous floors,
     to fix the residual dust and to uniform the
     substrates absorption prior to levelling.
     Apply on perfectly dry gypsum or anhydrite
     surfaces (residual moisture less than 0.5%).
     The substrate must be dry and clean, free
     from oil, grease, traces of paint and any
     loose particles.

     Technical data:
     Consistency: liquid.
     Colour: light blue.
     Flammability: no.
     Application temperature range:
     from +5°C to +40°C.
     Drying time: 2 hours, varies according to
     the dilution and absorbency of the
     substrate.
     EMICODE: EC 1 - very low emission.
     Storage: 24 months. Protect from frost.
     Application: by roller and brush.

     Consumption
     0.1-0.2 kg/m2 depending on the use.

     Packaging
     25 - 10 - 5 - 1 kg plastic drums.
C L E A N I N G M AT E R I A L S , P R I M E R S , I N S U L AT I N G M AT E R I A L S ,
    C O N S O L I D AT I N G C O M P O U N D S A N D M O I S T U R E B A R R I E R S


                                                                                                                    SP            17
                                                                                           m
                                                                                       epri
                                                                                    Map
                                                                      T
                                                          m
                                            o          Pri
                                          Ec

                                                                                  Solvent-free two-component primer.

                                                                                  Where to use:
                                                                                  Improves the bonding of smoothing and
                                                                                  levelling compounds on gypsum and
                                                                                  anhydrite, on very flat and compact
                                                                                  surfaces such as ceramic tiles and natural
                                                                                  stone.
                                                                                  Wait until Mapeprim SP becomes
                                                                                  transparent before applying levelling
                                    Solvent-free acrylic primer with very         compounds.
                                    low emission of volatile organic              Use Mapeprim SP only on dry surfaces
                                    compounds (VOC) for porous and non            that are not subject to rising damp. The
                                    porous surfaces.                              substrate must be dry and clean, free from
                                                                                  oil, grease, traces of paint and any other
                                    Where to use:                                 loose particles.
                                    All-purpose primer for improving adhesion
                                    of levelling compounds on all porous and      Technical data:
                                    non-porous surfaces: cement, gypsum,          Consistency: Part A: liquid; Part B: liquid.
                                    anhydrite, asphalt, wood, terrazzo. The       Colour: Part A: light blue; Part B: white.
                                    substrate must be dry and clean, free from    Flammability: no.
                                    oil, grease, paint and any loose particles.   Application temperature range:
                                                                                  from +5°C to +40°C.
                                    Technical data:                               Pot life: approx. 1 hour.
                                    Consistency: liquid.                          Mixing ratio: Part A : Part B = 1 : 1.
                                    Colour: white.                                Waiting time before application of
                                    Flammability: no.                             smoothing compound: between 1 and
                                    Application temperature range:                3 hours depending on the ambient
                                    from +5°C to +40°C.                           conditions.
                                    EMICODE: EC 1 - very low emission.            Maximum time for application of
                                    Storage: 24 months. Protect from frost.       smoothing compound: 24 hours.
                                    Application: by roller and brush.             Storage: 24 months.
                                                                                  Application: by brush, roller or flat trowel.
                                    Consumption
                                    0.10-0.20 kg/m2.                              Consumption
                                                                                  0.10-0.20 kg/m2.
                                    Packaging
                                    20 and 5 kg drums.                            Packaging
                                                                                  4 and 2 kg drums.
18
                   L
                erK
            Prim
                                                                   r
                                                                 me 6
                                                              Pri329



     Adhesion promoter on non-porous
     surfaces for epoxy, epoxy-
     polyurethane and two-component
     polyurethane adhesives.

     Where to use:
     Adhesion promoter for Lignobond and             Aqueous acrylic primer with excellent
     Ultrabond P902 2K on existing flooring in:      penetration effect for dusty screeds.
     • ceramic tiles;
     • porcelain tiles;                              Where to use:
     • glass mosaic;                                 Consolidation of unsound substrates.
     • marble;                                       Preparation of unsound screed surfaces
     • terrazzo;                                     before the installation of wooden flooring
     • etc.                                          with vinyl adhesives. Primer for
     After the application with a wet cotton         cementitious smoothing compounds.
     cloth, it is important that dust, dirt or any
     other substance that could interfere with       Technical data:
     the bonding of the adhesive used for            Consistency: liquid.
     installing the wooden flooring does not         Colour: opalescent.
     deposit over the surface.                       Flammability: no.
                                                     Application temperature range:
     Technical data:                                 from +10°C to +35°C.
     Consistency: liquid.                            Dilution: no, 1:1 or 1:2 with water
     Colour (pinkish): transparent.                  depending on the absorption of the
     Flammability: yes.                              substrate.
     Application temperature range:                  Drying time: 1-5 days.
     from +5°C to +35°C.                             Waiting time before laying with vinyl
     Drying time: 5 minutes.                         adhesives: when dry.
     Storage: 12 months.                             Storage: 12 months.
     Application: wet cotton cloth.                  Application: roller, large brush, brush or
                                                     watering can.
     Consumption
     30-40 g/m2.                                     Consumption
                                                     0.1-0.5 kg/m2.
     Packaging
     1 litre bottles in boxes of 12.                 Packaging
                                                     10 and 5 kg drums.
C L E A N I N G M AT E R I A L S , P R I M E R S , I N S U L AT I N G M AT E R I A L S ,
    C O N S O L I D AT I N G C O M P O U N D S A N D M O I S T U R E B A R R I E R S



                                                                                                                                19




                                                m
                                             igu
                                          Liv                                                  A
                                                                                            erP
                                                                                        Prim




                                 Additive in water dispersion for
                                 cementitious smoothing compounds
                                 and mortars.

                                 Where to use:                                   Ready-to-use synthetic resin based
                                 • Additive for improving the mechanical         solvent primer for bonding with
                                   and adhesion strength of cementitious         Adesilex PA.
                                   screeds, renders and coatings.
                                 • Additive for the preparation of cement        Where to use:
                                   based slurries to form bonded screeds,        Preparation of substrates before the laying
                                   for filling depressions and repairing parts   of wooden flooring with Adesilex PA
                                   of screeds.                                   adhesive.
                                 • Diluted 1: 4 - 1: 5 with water, it fixes      Primer PA dries rapidly, penetrates into the
                                   surface dust on screeds before the            substrate and ensures excellent adhesion
                                   installation of wooden flooring with vinyl    to Adesilex PA.
                                   adhesives.
                                 Livigum can be diluted from 1:2 to 1:5 with     Technical data:
                                 water depending on the type of application.     Consistency: liquid.
                                                                                 Colour: red.
                                 Technical data:                                 Flammability: yes.
                                 Consistency: viscose liquid.                    Application temperature range:
                                 Colour: white.                                  from +10°C to +35°C.
                                 Flammability: no.                               Drying time: 4-48 hours depending on the
                                 Application temperature range:                  absorption.
                                 from +5°C to +35°C.                             Waiting time before laying with
                                 Storage: 12 months. Protect from frost.         Adesilex PA: 1-2 days.
                                                                                 Storage: 12 months.
                                 Consumption                                     Application: brush, roller, trowel.
                                 depending on dilution.
                                                                                 Consumption
                                 Packaging                                       0.5-0.6 kg/m2
                                 25 - 10 - 5 kg drums.
                                                                                 Packaging
                                                                                 10 kg drums.
                      e rs,
20
                    im ing
                  Pr at
                          r
                solidnd/o
            con ds a iers
              un barr
          po ure
       com ist                    0
        mo                     PU6
               s            er
                   fa                                      m
               Pros                                     Pri




                                                      One-component polyurethane
                                                      moisture curing primer in solvent for
                                                      consolidating and waterproofing
     Solvent-free silicate based                      cementitious screeds.
     consolidating compound for
                                                                                                                U
                                                                                                              rP
     cementitious substrates.                         Where to use:
                                                      Waterproofing porous cementitious screeds
     Where to use:                                    that have residual moisture higher than the
                                                                                                             e
                                                                                                          inn
     Consolidation of cementitious substrates         maximum quantity acceptable for the
     with poor consistency even in depth,

                                                                                                        Th
                                                      installation of wooden flooring.
     hardening cementitious screeds that tend         Consolidation of unsound substrates
     to crumble on the surface. To prevent the        and/or with poor mechanical strength. Anti-
     formation of an anti-adhesive film, sprinkle     dust treatment of cementitious and
     dry sand on the surface of the final coat to     anhydrite screeds. During application,
     facilitate bonding of the next treatment.        provide suitable ventilation. If smoothing
     The substrate must be dry and clean, free        compounds or adhesives will be used after
     of oil, grease, paint and any loose particles.   the application of Primer PU60, spread
                                                      Quartz 1.2 or dry clean sand over the just
     Technical data:                                  treated surface in order to improve the
     Drying time: varies according to the             bonding strength of the products to be
     absorbency of the substrate.                     applied.
     Consistency: liquid.
     Colour: transparent.                             Technical data:
     Flammability: no.                                Consistency: liquid.
     Application temperature range:                   Colour: brown.
     from +5°C to +35°C.                              Flammability: yes.
     Storage: 24 months. Protect from frost.          Application temperature range:
     Application: by roller, brush or watering        from +5°C to +35°C.
     can.                                             Dilution: from 25 to 100% with                Thinner in solvent specific for
                                                      Thinner PU.                                   Primer PU60.
     Consumption                                      Set to light foot traffic: depending on the   Where to use:
     0.5-0.7 kg/m2.                                   dilution, 3-8 hours.                          Thinner for Primer PU60 and all one and
                                                      Hardening time: 24 hours.                     two-component polyurethane products.
     Packaging                                        Waiting time before laying with reactive
     25 kg drums.                                     glues: 2-7 days.                              Technical data:
                                                      Storage: 12 months.                           Consistency: liquid.
                                                      Application: roller or brush.                 Colour: transparent.
                                                                                                    Flammability: yes.
                                                      Consumption                                   Storage: 12 months.
                                                      0.4-1.2 kg/m2.
                                                                                                    Consumption
                                                      Packaging                                     0.25-1 l per litre of Primer PU60,
                                                      10 kg drums.                                  depending on the dilution necessary.
                                                                                                    Packaging
                                                                                                    9 kg drums.
C L E A N I N G M AT E R I A L S , P R I M E R S , I N S U L AT I N G M AT E R I A L S ,
    C O N S O L I D AT I N G C O M P O U N D S A N D M O I S T U R E B A R R I E R S


                                                                     m
                                                                  Pri 1K
                                                                                                       21

                                                                o
                                                              Ec PU




                                                        Single component, solvent-free,
                                                        hygro-hardening polyurethane primer
                                                        with very low emission of volatile
                                                        organic compounds (VOC), for
                                                        consolidating and waterproofing
                                                        cementitious screeds.

                                                        Where to use:
                                                        Waterproofing cementitious screeds with a
                                                        residual moisture content higher than the
                                                        maximum level recommended for laying
                                                        wooden floors.
                                                        Consolidating unstable and/or
                                                        mechanically weak substrates.
                                                        Anti-dust treatment for cementitious and
                                                        anhydrite screeds with a disjointed surface.
                                                        It may also be blended with quartz and
                                                        used as a binder to mix synthetic mortar for
                                                        small smoothing and repair operations.
                                                        If smoothing compound or parquet floor is
                                                        to be laid after applying Eco Prim PU 1K,
                                                        Quartz 1.2 or clean, dry sand must be
                                                        sprinkled on the surface immediately after
                                                        treatment to improve the bond of
                                                        successive applications.
                                                        If sand is not sprinkled on the surface, the
                                                        wooden floor must be laid within 12-36
                                                        hours using a reactive polyurethane
                                                        adhesive (such as Ultrabond P990 1K) or
                                                        an epoxy-polyurethane adhesive (such as
                                                        Lignobond or Ultrabond P902 2K).

                                                        Technical data:
                                                        Consistency: liquid.
                                                        Colour: brown.
                                                        Flammability: no.
                                                        Application temperature range: from
                                                        +5°C to +35°C.
                                                        Set to foot light traffic: approx. 9 hours.
                                                        Hardening time: 12-16 hours.
                                                        Waiting time for installation with
                                                        reactive adhesives: 12-36 hours.
                                                        EMICODE: EC 1R - very low emission.
                                                        Storage: 12 months.
                                                        Application: by brush or roller.

                                                        Consumption
                                                        0.2-0.4 kg/m2 per coat.

                                                        Packaging
                                                        10 kg drums.
                  F
22             erM
           Prim
                                                                 P
                                                              erE
                                                          Prim


     Two-component solvent-free epoxy
     primer to be used as an adhesion
     promoter for products from the
     Mapefloor range and to consolidate
     and waterproof cementitious
     substrates.

     Where to use:
     • Consolidating compound by impregnation
        of cementitious screeds, also radiant       Two-component waterproofing and
        heated screeds, and unsound anhydrite       consolidating primer, in solvent
        screeds.                                    solution, for screeds and industrial
     • Consolidating impregnation with anti-dust    flooring.
        effect of concrete floors in garages,
        warehouses, industries, etc. and            Where to use:
        cementitious surfaces before the            • Primer for the consolidation of surfaces of
        installation of raised flooring.               dusty or crumbly cementitious screeds,
     • Waterproofing screeds and concrete              for anhydrite screeds, radiant heated
        floors to prevent the excess rising of         screeds, old terrazzo tiles, gypsum and
        residual moisture.                             gypsum board.
     If smoothing compounds or adhesives will       • Waterproofing damp screeds to isolate
     be used after the application of Primer MF,       residual moisture.
     spread Quartz 1.2 or dry clean sand over       • Anti-dust impregnating primer over
     the just treated surface in order to improve      industrial flooring, garages, raised
     the bonding strength of the products to be        flooring.
     applied.                                       If a levelling compound is used after the
                                                    application of Primer EP, spread dry sand
     Technical data:                                over the just treated surface to create a
     Consistency: liquid.                           suitable mechanical key.
                                                                                                                .2
                                                                                                              z1
     Colour: transparent yellow.                    The substrate must be dry and clean, free


                                                                                                           art
     Flammability: no.                              of oil, grease, traces of paint and any loose
     Application temperature range:                 particles.


                                                                                                         Qu
     from +10°C to +35°C.
     Waiting time before the installation of        Technical data:
     floors or application of smoothing             Minimum drying time: 24 hours
     compounds: 24-48 hours depending on            depending on the porosity of the substrate.
     the temperature.                               Consistency: liquid.
     Pot life: 90 minutes.                          Colour: transparent.
     Mixing ratio: Part A : Part B = 3 : 1.         Flammability: yes.
     Storage: 24 months.                            Application temperature range:
     Application: roller and brush.                 from +10°C to +40°C.
                                                    Pot life of the mixture: 4-5 hours.
     Consumption                                    Mixing ratio: Part A : Part B = 1 : 1.
     0.2-0.3 kg/m2, varies according to the         Storage: 24 months.
     absorption of the substrate.                   Application: by roller, brush or watering
                                                    can.
     Packaging
     1 kg (A+B) and 6 kg (A+B) units.               Consumption
                                                    0.5-0.7 kg/m2.

                                                    Packaging
                                                    5+5 kg drums.                                   Washed and dried siliceous sand with
                                                                                                    controlled grading to be used to
                                                                                                    ensure bonding over resins or epoxy
                                                                                                    primers.

                                                                                                    Where to use:
                                                                                                    Can be used in all cases where rough
                                                                                                    surfaces are absolutely necessary to help
                                                                                                    the adhesion of smoothing compounds and
                                                                                                    adhesives over resins or epoxy primers.

                                                                                                    Technical data:
                                                                                                    Colour: grey - beige.
                                                                                                    Grading: 0.7-1.2.

                                                                                                    Packaging
                                                                                                    25 kg bags.
C L E A N I N G M AT E R I A L S , P R I M E R S , I N S U L AT I N G M AT E R I A L S ,
    C O N S O L I D AT I N G C O M P O U N D S A N D M O I S T U R E B A R R I E R S



                                                                                                             23
                                                                           P
                                                                      lock
                                                                  Trib




                                                            Three-component, epoxy-
                                                            cementitious primer for
                                                            waterproofing damp substrates,
                                                            including non-absorbent ones.

                                                            Where to use:
                                                            Triblock P is used as a waterproofing
                                                            system for damp substrates, especially:
                                                            • old ceramic or terrazzo floor dressings
                                                              on substrates with excessive residual
                                                              humidity;
                                                            • cementitious substrates with a humidity
                                                              content higher than the recommended
                                                              level for laying wooden or resilient floors.
                                                            Triblock P is a three-component epoxy-
                                                            cementitious system which is diluted with
                                                            water. It has the capacity of reticulating on
                                                            even very smooth, damp surfaces and of
                                                            forming a compact, waterproof layer which
                                                            is suitable for laying parquet, PVC,
                                                            linoleum, rubber and cementitious
                                                            smoothing compounds.
                                                            The surface must be dry, clean and free of
                                                            grease, oil, traces of old paintwork and
                                                            any other coating which may be removed.

                                                            Technical data:
                                                            Consistency: component A liquid;
                                                            component B liquid; component C powder.
                                                            Colour: component A white; component B
                                                            white; component C white.
                                                            Inflammable: no.
                                                            Recommended application
                                                            temperature range: from +5°C to +35°C.
                                                            Waiting time between the first and
                                                            second coat: 4-6 hours.
                                                            Waiting time before laying
                                                            floors or smoothing compounds:
                                                            18 hours.
                                                            Pot life: 30-40 minutes.
                                                            Mixing ratio: component A : component B
                                                            : component C = 12 : 38 : 50.
                                                            Shelf life: 24 months.
                                                            Application: by brush or roller.

                                                            Consumption
CANOVA AIRPORT - Treviso - Italy                            0.5 kg/m2.
Prodoucts used: EPORIP, PLANICRETE, PRIMER KL,
PRIMER MF, TOPCEM PRONTO, ULTRABOND P902 2K,                Packaging
ULTRAPLAN, ULTRAPLAN MAXI, TRIBLOCK P                       15 kg drums (A+B+C).
                                 CLEANING MATERIALS, PRIMERS,
                          INSULATING MATERIALS, CONSOLIDATING
                            COMPOUNDS AND MOISTURE BARRIERS

24



         ants
     Seal
                       p
                    ori
                  Ep
                                                                    o
                                                                Turb
                                                           orip
                                                         Ep

       Two-component epoxy adhesive for
       cold joints and sealing of cracks in
       screeds. Solvent-free.

       Where to use:
       • Creation of cold joints between fresh and
         old concrete.
       • Stiff sealing of damages or cracks in
         screeds, cement floors, etc.
                                                      Very fast hardening two-component
       When it is necessary to recreate the
                                                      polyester resin.
       monolithic property of the structure, apply
       Eporip on clean and dry surfaces.
                                                      Where to use:
       The substrate must be clean, dry, free from
                                                      • Sealing cracks in screeds.
       oil, grease, traces of paint and other loose
                                                      • By adding dry sand, Eporip Turbo can be
       material.
                                                        used to manufacture mortars for small
                                                        reparations.
       Technical data:
                                                      Eporip Turbo hardens in approximately
       Consistency: Part A: fluid paste; Part B
                                                      20 minutes.
       fluid paste.
       Colour: Part A: black; Part B: white.
                                                      Technical data:
       Mixing ratio: Part A : Part B = 3 : 1.
                                                      Consistency: Part A: fluid paste;
       Flammability: no.
                                                      Part B: fluid paste.
       Application temperature range:
                                                      Colour: Part A: grey; Part B: white.
       from +5°C to +30°C.
                                                      Mixing ratio: Part A : Part B = 500 : 8.
       Setting time: 24 hours.
                                                      Flammability: yes.
       Workability: 60 minutes.
                                                      Application temperature range:
       Open time: 5 hours.
                                                      from +5°C to +30°C.
       Storage: 12 months.
                                                      Setting time: 20-30 minutes.
       Application: by brush, trowel or by
                                                      Workability: 7 minutes.
       pouring.
                                                      Storage: 12 months.
                                                      Application: by trowel or by pouring.
       Consumption
       0.5-2 kg/m2.
                                                      Consumption
                                                      1.7 kg per litre of cavity to be filled.
       Packaging
       10 and 2 kg kit.
                                                      Packaging
                                                      508 g metal cans
                                                      (Part A: 500 g; Part B: 8 g).
                                                               CLEANING MATERIALS, PRIMERS,
                                                        INSULATING MATERIALS, CONSOLIDATING
                                                          COMPOUNDS AND MOISTURE BARRIERS

               g
           nin s
                                                                                                                                     25


        learial
      C e
      mat                                                                                               New
                                                                                                          H
                                                                                                      ner
                  l
                                                                                                  Clea
              lico                                           er
                                                                L
            Pu                                              n
                                                        Clea



                                                                                           Damp wipes for cleaning hands.

                                                                                           Where to use:
Solvent gel to remove adhesives and                                                        Removing traces of fresh adhesive and
paint.                                                                                     sealant from hands and surfaces.
                                               Cleaning solution for pre-finished          Particularly suitable for removing traces of
Where to use:                                  parquet.                                    single component, polyurethane adhesive
• Removal of old natural and synthetic resin                                               (such as Ultrabond P990 1K and
  based adhesives and paint.                   Where to use:                               Ultrabond Eco P992 1K) and
• Cleaning old adhesives from marble and       Removal of traces of single component,      two-component epoxy-polyurethane
  ceramic flooring, levelling compounds,       polyurethane adhesive, epoxy adhesive and   adhesive (such as Ultrabond P902 2K
  ceramic tiles, mosaic, gypsum, metal,        two-component, epoxy-polyurethane           and Lignobond).
  fibre-cement coverings.                      adhesive.                                   Cleaner H wipes are a quick, handy item
After treatment with Pulicol wash the                                                      for cleaning hands on site when water is
surface with water and soda then rinse.        Technical data:                             not available. The detergent solution which
                                               Consistency: liquid.                        saturates the wipes contains vitamin E and
Technical data:                                Colour: transparent.                        real aloha that protects hands and leaves
Consistency: gel.                              Flammability: yes.                          a pleasant smell.
Colour: transparent.                           Application temperature range: from
Flammability: yes.                             +5°C to +35°C.                              Packaging
Application temperature range:                 Drying time: 24 hours.                      plastic tubs containing 80 wipes
from +10°C to +35°C.                           Storage: 12 months.                         (20x30 cm).
Waiting time before removal:                   Application: with a cotton rag.
– adhesives in water dispersion or in
  solution: 5 minutes;                         Consumption
– reactive adhesives: 60 minutes.              5-20 g/m2.
Storage: 24 months.
Application: by brush.                         Packaging
                                               multi-pack of 12 1 I (0.85 kg) - bottles.
Consumption
0.3 kg/m2.

Packaging
3 and 1 kg drums.
                 a ble
              nt
           tio    ive
                      s
       elec
      S        hes tion
             ad a l
          peinstal loors
       Ma e i n f
    of th de
     forf woo
       o




                                                                                                                                                                     Adesilex LC/RP
                                                                                                                                                     Adesilex LC/R
                                                                                        P992 1K




                                                                                                                                                                                      Adesilex LC
                                                                                   Eco P992 1



                                                                                                                  P990 1K
                                                                                                   P997 1K T



                                                                                                                               P902 2K

                                                                                                                                         Lignobond
                                                                                                               Ultrabond

                                                                                                                            Ultrabond
                                                                                   Ultrabond

                                                                                                  Ultrabond
        Substrates
TYPES OF PARQUET
Mosaic (EN 13488)
Solid wood without joints (EN 13227)
Solid jointed wood (EN 13226)
Assembled control panels (EN 13629)
Plywood elements (EN 13489)
Laminated and floating
Wood skirting
Stairs


KEY                 This symbol is used to identify MAPEI products which give off a
                    low level of volatile organic compounds (VOC) as certified by
                                                                                                                  MAPEI recommended
                    GEV (Gemeinschaft Emissionskontrollierte Verlegewerkstoffe,                                   Small sized (L < 500 mm)
                    Klebstoffe und Bauprodukte e.V.), an international organisation for
                    controlling the level of emissions from products used for floors.
                                                                                                                  Kerb laying



                                      N.B. - THIS TABLE IS MERELY INDICATIVE; FOR FURTHER INFORMATION,
                                             REFER TO THE TECHNICAL DATA SHEET FOR EACH PRODUCT
                                               S E L E C T I O N TA B L E O F M A P E I A D H E S I V E S
                                         F O R T H E I N S TA L L AT I O N O F W O O D E N F L O O R S



                                                                                                      27
                       PA
Adesivil D3




                               Eco 575
              Adesilex P

                            Ultrabond
             inyl
          r v ves
28
                                                                   P
       ateesi
     W h                                                      xL
                                                                C/R
                                                           ile
      ad                                               Ad
                                                         es



                   LC/R
              ilex
            es
          Ad                                          Adhesive in water dispersion and with
                                                      low water content for bonding wooden
                                                      flooring.

                                                      Where to use:
                                                      Bonding of:
                                                      • wood-back strips and mosaic wooden
                                                        flooring;
                                                      • all types of wooden strips;
                                                      • small wood strips not very sensitive to
                                                        moisture.

                                                      Technical data:
                                                      Consistency: thick paste.
                                                      Colour: beige and brown.
         Fast-setting adhesive in water               Flammabily: no.
         emulsion and with low water content          Application temperature range:
         for bonding wooden flooring.                 from +10°C to +30°C.
                                                      Open time: approximately 30 minutes.
         Where to use:                                Set to light foot traffic: after 24 hours.
         Bonding of:                                  Polishing: once completely dry (minimum
         • wood-back strips and mosaic wooden         10 days).
           flooring;                                  Storage: 24 months. Protect from frost.
         • strips, blocks;                            Application: notched trowel.
         • small wood strips of all types of wood.
                                                      Consumption
         Technical data:                              0.8-1.0 kg/m2.
         Consistency: thick paste.
         Colour: beige and brown.                     Packaging
         Flammabily: no.                              20 and 12 kg drums.
         Application temperature range:
         from +10°C to +30°C.
         Open time: approximately 30 minutes.
         Set to light foot traffic: after 24 hours.
         Polishing: once completely dry (minimum
         10 days).
         Storage: 24 months. Protect from frost.
         Application: notched trowel.

         Consumption
         0.8-1.0 kg/m2.

         Packaging
         20 and 12 kg drums.
       A D H E S I V E S F O R W O O D E N A N D L A M I N AT E F L O O R I N G


PRIVATE APARTMENT - Reggio Emilia - Italy
Wooden flooring laid with ADESILEX LC/R and ULTRABOND P902 2K
on screed carried out with ECO PRIM PI 1K
                                                                                                                                                    29




                                                                         C
                                                                      exL                                              3
                                                                  esil                                           ivil D
                                                                Ad                                             es
                                                                                                             Ad




                                                           Adhesive in water emulsion for
                                                           bonding wooden flooring.
                                                                                                        Solvent-free adhesive for prefinished
                                                           Where to use:                                water resistant floating wooden or
                                                           Bonding of:                                  laminate flooring.
                                                           • wood-back strips and mosaic wooden
                                                             flooring;                                  Where to use:
                                                           • all types of wooden strips and blocks;     Bonding of:
                                                           • small wood strips not very sensitive to    • joints between pieces of prefinished
                                                             moisture.                                    wooden flooring;
                                                                                                        • small wooden pieces;
                                                           Technical data:                              • DIY works.
                                                           Consistency: thick paste.
                                                           Colour: beige and brown.                     Technical data:
                                                           Flammability: no.                            Consistency: viscose liquid.
                                                           Application temperature range:               Colour: white.
                                                           from +10°C to +30°C.                         Dried film: transparent.
                                                           Open time: approximately 30 minutes.         Flammability: no.
                                                           Set to light foot traffic: after 24 hours.   Application temperature range:
                                                           Polishing: once completely dry (minimum      from +15°C to +35°C.
                                                           20 days).                                    Open time: 5-10 minutes.
                                                           Storage: 24 months. Protect from frost.      Set to light foot traffic: after approx.
                                                           Application: notched trowel.                 12 hours.
                                                                                                        Final hardening: approximately 24 hours.
                                                           Consumption                                  Resistance to water: D3
                                                           0.8-1.0 kg/m2.                               class/EN 204-205.
                                                                                                        Storage: 24 months. Protect from frost.
                                                           Packaging                                    Application: extrusion from the nozzle of
                                                           20 and 10 kg drums.                          the bottle.

                                                                                                        Consumption
                                                                                                        0.025 kg/m or 0.1-0.2 kg/m2.

                                                                                                        Packaging
                                                                                                        0.5 kg bottles.
             ves
        h esi ins
     Ad res ol
       on lcoh
based in a
                A
             exP
         esil
       Ad




   Adhesive based on synthetic resins in
   alcohol for bonding wooden flooring.

   Where to use:
   Bonding of:
   • wood-back strips and mosaic wooden
     flooring;
   • all types of wooden strips and blocks;
   • small sized prefinished wooden flooring.

   Technical data:
   Consistency: creamy paste.
   Colour: beige.
   Flammabily: yes.
   Application temperature range:
   from +10°C to +30°C.
   Open time: approx. 10-20 minutes.
   Set to light foot traffic: after 24-72 hours.
   Polishing: at least 72 hours.
   Storage: 24 months.
   Application: notched trowel.

   Consumption
   0.6-1.2 kg/m2.

   Packaging
   16 kg drums.




                                                    FLATS IN WIENERBERG - Austria
                                                   Products used: TOPCEM PRONTO,
                                                           PRIMER PA, ADESILEX PA
A D H E S I V E S F O R W O O D E N A N D L A M I N AT E F L O O R I N G




                                                                                31

                              HOTEL WERZER - Pörtschach - Austria
                              Products used: NIVORAPID, PRIMER G, ADESILEX PA
                       t
                    nen
                  po and
              com ne ent
32
             -
           ne etha on e
         O ur     p
          ly -comethan s                                                        d
                                                                             on 2K
       po o ur ive                                                          b
                                                                         tra902
         tw oly hes                                                    Ul P
            p
        xy- ad                d
     epo                   bon
                         no
                         Lig

                                                                   Two-component epoxy-polyurethane
                                                                   adhesive for wooden flooring.

                                                                   Where to use:
                                                                   Bonding of all types and sizes of wooden
                                                                   flooring.

                                                                   Technical data:
                                                                   Consistency: Part A: pasty;
                   Two-component solvent and water                 Part B: pasty.
                   free epoxy-polyurethane adhesive for            Colour: Part A: beige or brown;
                   wooden flooring.                                Part B: grey-green.
                                                                   Flammabily: no.
                   Where to use:                                   Mixture ratio: Part A : Part B = 90 : 10.
                   Bonding of all types and sizes of wooden        Pot life: 60-70 minutes.
                   flooring.                                       Application temperature range:
                                                                   from +10°C to +30°C.
                   Technical data:                                 Open time: 1 hour.
                   Consistency: Part A: thick paste; Part B:       Set to light foot traffic: after 24 hours.
                   fluid paste.                                    Polishing: after 3 days.
                   Colour: Part A: dark brown or beige;            Storage: 24 months.
                   Part B: straw yellow.                           Application: notched trowel.
                   Flammabily: no.
                   Mixture ratio: Part A : Part B = 90 : 10.       Consumption
                   Pot life: 50-60 minutes.                        1.0-1.5 kg/m2.
                   Application temperature range:
                   from +10°C to +30°C.                            Packaging
                   Open time: 1 hours.                             10 kg drums.
                   Setting time: 5 hours.
                   Set to light foot traffic: after 12-24 hours.
                   Polishing: after 3 days.
                   Storage: 24 months.
                   Application: notched trowel.

                   Consumption
                   1.0-1.5 kg/m2.

                   Packaging
                   10 kg and 5 kg drums.
                 A D H E S I V E S F O R W O O D E N A N D L A M I N AT E F L O O R I N G


HOTEL NHOW - Milan - Italy
Wooden flooring installed with ULTRABOND P902 2K on screeds prepared
with MAPECEM, MAPECEM PRONTO, TOPCEM and TOPCEM PRONTO
                                                                                      33
34

                d
              on 1K
            ab
         ltrP990
        U                                                          New
                                                                 d
                                                             bonK T
                                                          tra 7 1
                                                        Ul 99
                                                         P

     Ready-to-use polyurethane one-
     component, solvent-free, elastic
     adhesive for all types of wooden and
     laminate flooring.

     Where to use:
     Bonding of all types and sizes of wooden
     and laminate flooring. Also suitable for
     bonding wooden skirting.
     Particularly suitable for underfloor heating   Solvent-free, single component,
     systems.                                       ready-to-use, thixotropic polyurethane
     Ultrabond P990 1K is odourless, solvent        adhesive for laying wooden steps.
     free and extent from free amines, therefore
     even installers allergic to epoxy and epoxy-   Where to use:
     polyurethane products can use it.              Laying wooden uprights treads and stairs.
                                                    Also suitable for bonding wooden
     Technical data:                                baseboards and for laying pre-finished,
     Consistency: creamy paste.                     three-layered parquet with beads of
     Colour: beige and brown.                       adhesive:
     Flammability: no.
     Application temperature range:                 Technical data:
     from +10°C to +35°C.                           Consistency: thixotropic paste.
     Open time: 110 minutes.                        Colour: ochre.
     Set to light foot traffic: after 12 hours.     Inflammable: no.
     Polishing: after 3 days.                       Recommended application temperature
     Storage: 12 months.                            range: from +10°C to +35°C.
     Application: notched trowel.                   Open time: approx. 100 minutes.
                                                    Set to light foot traffic: after 12 hours.
     Consumption                                    Polishing: after 3 days.
     0.8-1.0 kg/m2.                                 Storage: 12 months.
                                                    Application: by extrusion.
     Packaging
     15 and 7 kg in aluminium bags contained in     Consumption
     plastic drums.                                 – installing wooden stairs: the yeald is
     Carton containing twenty 600 cc aluminium        ca. 2 m2 each soft cartridge (diagonal
     soft cartridges.                                 bead with the distance of 5-10 cm);
                                                    – installing pre-finished parquet with three
                                                      layers: the yeald is ca. 4/6 m2 each soft
                                                      cartridge (diagonal bead with the distance
                                                      of 10-15 cm);
                                                    – installing wood skirtings: the yeald is
                                                      ca. 15 ml each soft cartridge.

                                                    Packaging
                                                    boxes containing 20 aluminium soft
                                                    cartridges, each one containing 600 c.c.
A D H E S I V E S F O R W O O D E N A N D L A M I N AT E F L O O R I N G




                                                                                          35




                                                         New
                                                       d
                                                    bon 2 1K
                                                tra P99
                                              Ul co
                                               E




                                            Solvent-free, single component,
                                            ready-to-use, flexible polyurethane
                                            adhesive with an extremely low
                                            emission level of volatile organic
                                            compounds, for all types of parquet
                                            and laminates.

                                            Where to use:
                                            Bonding all types and formats of
                                            conventional wooden parquet, pre-finished
                                            elements and laminates on all types of
                                            substrate and It is particularly suitable
                                            for heated substrates. It is also suitable
                                            for floor layers allergic to epoxy and
                                            epoxy-polyurethane products.
                                            Does not carry any hazard warning
                                            indication and is completely free of
                                            solvents and any substance which gives off
                                            unpleasant odours therefore is particularly
                                            suitable for rebuilding work, and for use
                                            close to inhabited areas.

                                            Technical data:
                                            Consistency: creamy paste.
                                            Colour: beige.
                                            Inflammable: no.
                                            Recommended application temperature
                                            range: from +10°C to +35°C.
                                            Open time: 140 minutes.
                                            Set to light foot traffic: after 12 hours.
                                            Facing: after 3 days.
                                            Storage: 12 months.
                                            Application: notched trowel.

                                            Consumption
                                            0.8-1.0 kg/m2.

                                            Packaging
                                            15 kg aluminium bags contained in
                                            plastic drums.
               s for
36
           sive and
       he ting les
     Ad kir ofi
      s pr                                                           d
                                                                  bon 1K
                                                               ra990
                    b
                        d
                     on 75                                  Ult P
                 traco 5
               Ul E



                                                         Ready-to-use polyurethane one-
                                                         component, solvent-free, elastic
                                                         adhesive for all types of wooden and
                                                         laminate flooring.
          High performance adhesive in water
          dispersion with very low emission of           Where to use:
          volatile organic compounds (VOC) for           Bonding of wooden skirting.
          bonding skirtings.
                                                         Technical data:
          Where to use:                                  Consistency: creamy paste.
          Ultrabond Eco 575 can be used for              Colour: beige and brown.
          bonding skirtings in stiff PVC, wood, carpet   Flammability: no.
          applied on the back of the skirting or         Application temperature range:
          directly on the wall. Apply enough on the      from +10°C to +35°C.
          back of the skirting or directly onto the      Open time: 110 minutes.
          substrate to allow the adhesive to transfer    Storage: 12 months.
          to both surfaces. Depending on the height      Application: notched trowel.
          of the skirting, apply one or more lines
          5 mm in diameter.                              Consumption
                                                         0.3-0.4 kg per 10 m.
          Technical data:
          Consistency: creamy paste.                     Packaging
          Colour: beige.                                 15 and 7 kg in aluminium bags contained in
          Flammability: no.                              plastic drums.
          Application temperature range:                 Carton containing twenty 600 cc aluminium
          from +5°C to +35°C.                            soft cartridges.
          Open time: approximately 25 minutes.
          Final handening time: 24 hours.
          Storage: 24 months. Protect from frost.
          Application: extrusion from the cartridge.

          Consumption
          – 325 ml cartridge: approximately 12 m per
            line.

          Packaging
          325 ml cartridges.
    ADHESIVES FOR SKIRTING AND PROFILES




                                             37
               New
            d
          onK T
       rab 1
    Ult997
     P




Solvent-free, single component,
ready-to-use, thixotropic polyurethane
adhesive for laying wooden steps.

Where to use:
Laying wooden uprights treads and stairs.
Also suitable for bonding wooden
baseboards and for laying pre-finished,
three-layered parquet with beads of
adhesive:

Technical data:
Consistency: thixotropic paste.
Colour: ochre.
Inflammable: no.
Recommended application temperature
range: from +10°C to +35°C.
Open time: approx. 100 minutes.
Set to light foot traffic: after 12 hours.
Polishing: after 3 days.
Storage: 12 months.
Application: by extrusion.

Consumption
ca. 15 ml each soft cartridge.

Packaging
boxes containing 20 aluminium soft
cartridges, each one containing 600 c.c.
38
 8



     Tools

                 for
             elsng s
         rowelliund
        T lev o
            mp
         co




      American - 28 cm.
      Extralong - 50 cm.




                                                d e eter
                                             rbirom
                for s                      Cayg
          w elesive
              s                             h
       Troadh



                                         Chemical instrument for measuring the
                                         humidity in the substrates. The water reacts
                                         with the calcium carbide inside the
                                         hygrometer. Acetylene is formed which
                                         makes the pressure rise. The water content
                                         is determined by the pressure on the
      Normal metal notch N. 1            manometer.
      Normal metal notch N. 2            The hygrometer comes in a plastic suitcase
      Normal metal notch N. 3            containing:
      Normal metal notch N. 4            – a steel container with a stopper and a
      Normal metal notch N. 5              manometer;
      Normal metal for wooden flooring   - 20 glass phials containing calcium
                                           carbide;
                                         - 2 aluminium marbles;
                                         - 1 scale with support, scalepan, and 20 g
                                           and 10 g weights;
                                         - 1 syringe;
                                         - 1 small steel spoon and plate.
                                         20 boxes containing glass calcium carbide
                                         phials are available.
                                                                                                                TOOLS




                                                                                                                               39




                                                            r
                                                         fonts
                                                       n
                                                     Gu ala
                                                     se
                                                                                               r
                                                                                           olle
                                                                                        edr
                                                                                    Spik

                                               Gun for 310 ml cartridges.




                                                       foir ges                  Plastic roller, 23 cm wide and 8 cm in


                                                    unrtr d
                                                                                 diameter with a handle.
                                                                                 To be used to improve the flow of levelling

                                                  G a                            compounds in thicknesses from 2 to
                                                                                 15 mm, to remove air bubbles and to

                                                   -c                            improve the appearance of the surface of

         nic ter                                oft
                                                                                 Mapei self-levelling compounds.

        o                                      s
    ctrrome
 Ele yg
   h


                                               Gun for 600 ml soft-cartridges.




Electronic instrument that rapidly indicates
the % of humidity contained in cement
based screeds (A scale), Mapecem based
screeds (B scale), and anhydrite based
screeds (C scale).
The hygrometer is powered by
9 V batteries and comes in a case
containing:
– a cable with a uniaxial connector and
  connecting terminals with the electrodes
  that are driven into the screed;
– two steel nails that are used as
  electrodes;
– an instruction leaflet.
 Eco Prim      ONE-COMPONENT,
               SOLVENT-FREE,
    PU 1K
40
               HYGRO-HARDENING
               POLYURETHANE PRIMER WITH
               VERY LOW EMISSION OF
               VOLATILE ORGANIC COMPOUNDS.
            PFor consolidating and
               waterproofing
               cementitious screeds

            PThanks to its waterproofing properties,
               it avoids excess of residual damp in the
               screeds before bonding of wood

            PPractical, easy-to-apply using either
               a roller or a brush

            PFluid, excellent penetration ability
            PHypo-allergenic
            PLow environmental impact
            PConvenient
PRODUCTS FOR THE         Ultrabond Eco
                         Ultrabond Eco
                                P992 1K
                                P992 1K
INSTALLATION OF WOOD                                          41
                          One-component, polyurethane adhesive
                          which improves the quality of work,
                          safeguards health and protects
                          the environment
                       PPractical and quick
                       PMulti-purpose
                       PCost-saving
                       PLess effort
                       PHigh performance
                       POdourless, hypo-allergenic
                       PLow environmental impact
                       PWithout hazard labelling



                          Two-component, epoxy-polyurethane
                          adhesive for wooden flooring
                       PEasy and quick to mix
                       PNew packaging that is even more practical
                          for use and handling

                       PHigh yield
                       PBetter final performance




                                                        www.mapei.com
                           M a p e i G ro u p
                                                                                        NORWAY - Rescon Mapei AS
                                       Europe                                           Vallsetvegen 6 - 2120 Sagstua
                                                                                        Tel. +47-62-972000
                                                                                        Fax +47-62-972099
                                                                                        Internet: http://www.resconmapei.com
                                          AUSTRIA - Mapei GmbH                          E-mail: post@resconmapei.no
                                          Fräuleinmühle 2                               Plant in Sagstua
                                          A - 3134 Nußdorf ob der Traisen
                                          Tel. +43-2783-8891 - Fax +43-2783-8893
                                          Internet: http://www.mapei.at                 POLAND - Mapei Polska Spzoo
Italy                                     E-mail: office@mapei.at                       ul. Gustawa Eiffel’a, 14 - 44-109 Gliwice
                                                                                        Tel. +48-32-7754450
                                          Plant in Traismauer
                                          Distribution centres in Wien,                 Fax +48-32-7754471
HEAD OFFICE                               Hall in Tirol and Graz                        Sales office:
                                                                                        Chałubińskiego Street 8, 00-613 Warsaw
                                                                                        Tel. +48-22-5954200
MAPEI SpA                                 BENELUX- Mapei Benelux SA/NV                  Fax +48-22-5954202
Via Cafiero, 22 - 20158 Milan             Zoning Industriel - Rue de l'Avenir, 40       Internet: http://www.mapei.pl
                                          B - 4460 Grâce-Hollogne                       E-mail: info@mapei.pl
Tel. +39-02-37673.1                       Tel. +32-4-2397070                            Plant in Gliwice
Fax +39-02-37673.214                      Fax +32-4-2397071
Internet: http://www.mapei.com            Internet: http://www.mapei.be                 PORTUGAL - Lusomapei, Produtos
                                          E-mail: mapei@mapei.be                        Químicos para a Construção, SA
E-mail: mapei@mapei.it                    For the Netherlands:                          E. N. 247 - Rua Do Belo Horizonte
                                          Tel. +31-43-3510498                           Ribamar - 2640-027 St.° Isidoro - MFR
Plants                                    Fax +31-43-3510499                            Tel. +351-261-860280
• Strada Provinciale 159                                                                Fax +351-261-860289
                                                                                        Internet: http://www.mapei.pt
  20060 Robbiano di Mediglia (Milan)                                                    E-mail: geral@mapei.pt
  Tel. +39-02-906911                                                                    Plant in Anadia
  Fax +39-02-90660575
                                                                                        ROMANIA - Mapei Romania SRL
                                          CZECH REPUBLIC - Mapei spol. s r.o.           14 Gen. Ion Dragalina
• Via Mediana S.S. 148 km 81.3            Smetanova 192 - 77211 Olomouc                 Str. Sector 5 - Bucarest
  04100 Latina                            Tel. +420-585224580 - Fax +420-585227209      Tel. +40-21-3117819
  Tel. +39-0773-2548                      Internet: http://www.mapei.cz                 Fax +40-21-3117821
                                          E-mail: info@mapei.cz                         Internet: http://www.mapei.ro
  Fax +39-0773-250391                     Distribution centre in Prague                 E-mail: info@mapei.ro

Distribution centre                                                                     RUSSIAN FEDERATION - ZAO Mapei
SASSUOLO                                                                                “Trading and Manufacturing”
                                          FRANCE - Mapei France SA                      Sales office:
Via Valle D’Aosta, 46                     Zone Industrielle du Terroir                  Derbenevskaya nab., 7,
                                          Avenue Léon Jouhaux, 29 - 31140 Saint Alban   building 4, 3-d floor
41049 Sassuolo (Modena)                   Tel. +33-5-61357305 - Fax +33-5-61357314      Moscow 113114 Russian Federation
Tel. +39-0536-803116                      Internet: http://www.mapei.fr                 Tel.+7-495-258-5520 - Fax +7-495-258-5521
Fax +39-0536-805255                       E-mail: mapei@mapei.fr                        Internet: http://www.mapei.ru
                                          Plants in Saint Alban and Montgru             E-mail: info@mapei.ru
                                          Saint Hilaire                                 Plants in Stupino
Office in Rome
Via Birmania, 87                          GERMANY - Mapei GmbH                          SLOVAK REPUBLIC - Mapei SK sro
(from 1/4/2008: Viale Libano, 28)         Bahnhofsplatz 10 - 63906 Erlenbach            Prievozská, 38 - 821 05 Bratislava
                                          Tel. +49-9372-98950                           Tel. +421-2-53414 705 / 53414 702
00144 Rome                                Fax +49-9372-989548                           Fax +421-2-5363 2692
Tel. +39-06-5929211                       Internet: http://www.mapei.de                 Internet: http://www.mapei.sk
Fax +39-06-59290337                       E-mail: mailto@mapei.de                       E-mail: office@mapei.sk
                                          Plant in Weferlingen

Office in Lecce                                                                         SLOVENIA - Mapei doo
Via Orsini del Balzo, 24                  GREAT BRITAIN - Mapei U.K. Ltd                Kočevarjeva 2 - 8000 Novo Mesto
                                          Mapei House - Steel Park Road - Halesowen     Tel. +386-1-7865050/51
73100 Lecce                                                                             Fax +386-1-7865055
                                          West Midlands B62 8HD
Tel. +39-0832-246551                      Tel. +44-121-5086970                          Internet: http://www.mapei.si
Fax +39-0832-248472                       Fax +44-121-5086960                           E-mail: mapei@mapei.si
                                          Internet: http://www.mapei.com                Distribution centre in Grosuplje
E-mail: ufficio.lecce@mapei.it            E-mail: sales@mapei.co.uk                     For Croatia: Tel. +385-1-3647789
                                          Plant in Halesowen                            E-mail: mapei@mapei.hr


                                                                                        SPAIN - Ibermapei SA
                                          GREECE - Mapei Hellas SA                      Plaza Cataluña, 20 - 5a Planta
                                          Papadiamantopoulou 24 C - 11528 Athens        08002 Barcelona
                                          Tel. +30-210-7472983                          Tel. +34-93-3435050
                                          Fax +30-210-7472953                           Fax +34-93-3024229
                                          Internet: http://www.mapei.gr                 Internet: http://www.mapei.es
                                          E-mail: mapeihellas@mapei.gr                  E-mail: ibermapei@ibermapei.es
                                                                                        Plants in Amposta (Tarragona) and
                                                                                        Cabanillas del Campo (Guadalajara)
                                          HUNGARY - Mapei Kft                           Distribution centres in Badalona
                                          Sport Utca 2 - 2040 Budaörs                   (Barcelona), Onda (Castellón) and
                                          Tel. +36-23-501667                            Marratxi (Mallorca)
                                          Fax +36-23-501666
                                          Internet: http://www.mapei.hu                 SWEDEN - Rescon Mapei AB
                                          E-mail: mapei@mapei.hu                        Gelbgjutarevägen 6 - 17148 Solna
                                          Plant in Sóskút                               Tel. +46-8-52509080
                                          Distribution centres in Györ, Kaposvàr        Fax +46-8-52509086
                                          and Miskolc                                   Internet: http://www.mapei.se
                                                                                        E-mail: info@mapei.se
   SWITZERLAND - Mapei Suisse SA                  SINGAPORE - Mapei Far East Pte Ltd
   1642 Sorens / FR                               28, Tuas West Road - 638383 Singapore
   Tel. +41-26-9159000 - Fax +41-26-9159003       Tel. +65-68623488
   Internet: http://www.mapei.ch                  Fax +65-68621012 / 68621013
   E-mail: info@mapei.ch                          Internet: http://www.mapei.com.sg
   Plant in Sorens                                E-mail: mapei@mapei.com.sg
                                                  Plant in Singapore

   UKRAINE - Mapei Ukraina LLC
   01014, Città di Kiev                           UNITED ARAB EMIRATES
   Ulica Strutinskogo, 8 - 8 Etazh.               I.B.S. (Innovative Building Solutions)
   Tel. +38-044-5024560, 5024563                  L.L.C.
   Fax +38-044-5024566                            P.O. Box 73869, Dubai, UAE
   Internet: http://www.mapei.ua
   E-mail: mapei@mapei.ua

                                                  VIETNAM - Mapei Vietnam Ltd.
                                                  Plot B, Northern part of Chu Lai Open
                                                  Economic Zone
                                                  Tamhiep Commune - Nuithanh District
                                                  Quangnam Province, Vietnam
                                                  Branch in Hanoi:

Asia-Oceania                                      Tel. (84-4) 9287924-6
                                                  E-mail: mapeihn@mapei.com.vn
                                                  Branch in Danang:
                                                  Tel. (84-511) 565001-4
                                                  E-mail: mapeidn@mapei.com.vn
                                                  Branch in Ho Chi Minh City:
   AUSTRALIA - Mapei Australia Pty Ltd            Tel. (84-6) 8206103-4-6
   12 Parkview Drive Archerfield                  E-mail: mapeihcm@mapei.com.vn
   Brisbane - Queensland 4108                     Plant in Chu Lai (Quangham)
   Tel. +61-7-3276 5000
   Fax +61-7-3276 5076
   Internet: http://www.mapei.com.au
   E-mail: mapei@mapei.com.au
   Plant in Brisbane


   CHINA - Mapei Construction Materials
   (Guangzhou) co. Ltd.
                                               The Americas
   Hong Fu Loi International Building
   Rm. 2003-2004, Yan Jiang Zhong Road            ARGENTINA - Mapei Argentina SA
   Guangzhou P.R. China                           Rondeau 51, 1° floor, Wilde - Buenos Aires
   Tel. (86-20) 83653489                          Tel. +54-11-42070009
   Fax (86-20) 83653481                           Fax +54-11-42171088
   E-mail: mapei-gz@mapei-gz.com                  Internet: http://www.mapei.com.ar
   Plant in Conghua (Guangzhou)                   Plant in Buenos Aires
   CHINA - Mapei Construction Materials
   (Shanghai) co. Ltd.                            CANADA - Mapei Canada Inc
   6, Lane 8999, Hunan Road,                      2900, Francis Hughes Avenue
   Nanhui District 201314                         Laval - QUE H7L3J5
   Shanghai P.R. China                            Tel. +1-450-6621212
   Tel. (86-21) 58180808                          Fax +1-450-6620444
   Fax (86-21) 58180909                           Internet: http://www.mapei.com
   E-mail: mapei-sh@mapei-sh.com                  Plants in Vancouver, Laval,
   Plant in Nanhui (Shanghai)                     Maskinongé and Toronto
   HONG KONG S.A.R. - Mapei China Ltd
   Suite 15, L22 Office Tower, Langham Place
   8 Argyle Street, Mongkok,                      PUERTO RICO - Mapei Caribe Inc
   Kowloon, Hong Kong                             Road 2 km 26.2 BO. Espinosa
   Tel. +852-21486816                             Dorado, Porto Rico 00646
   Fax +852-25121328                              Tel. +1-787-270-4162
   Internet: http://www.mapei.com.hk              Fax+1-787-270-4135
   E-mail: mapei@mapei.com.hk                     Internet: http://www.mapei.com
                                                  Plant in Dorado

   MALAYSIA - Mapei (Malaysia) Sdn Bhd            U.S.A. - Mapei Corp
   PT 521, Batu 23 - Jalan Rawang                 1144 East Newport Center Drive
   Jalan Batang Berjuntai                         Deerfield Beach, Florida 33442
   48000 Rawang - Selangor Darul Ehsan            Tel. +1-954-246-8888 / +1-888-300-4422
   Tel. +60-3-60935799                            Fax +1-954-246-8800
   Fax +60-3-60915801                             Internet: http://www.mapei.com
   Internet: http://www.mapei.com.sg              Plants in Phoenix (AZ), Garland (TX),
   E-mail: mapei@tm.net.my                        South River (NJ), Fort Lauderdale (FL),      www.mapei.com
   Plant in Rawang (Kuala Lumpur)                 West Chicago (IL), Fredericksburg (VA),
                                                  San Bernardino (CA)
                                                  Distribution centre in Anaheim (CA)
   NEW ZEALAND - Mapei New Zealand
   30 Fisher Crescent - Mt. Wellington
   Auckland, New Zealand                          VENEZUELA - Mapei de Venezuela CA
   Tel. +64-9-9211994 - Fax +64-9-9211993         Calle Orinco Torre D&D PB Lc 11-12
   Internet: http://www.mapei.co.nz               Urb. Las Mercedes
   E-mail: info@mapei.co.nz                       1071 Caracas
                                                  Tel. +58-212-991-1797/+58-212-9919423
                                                  Fax +58-212-991-7623
                                                  Internet: http://www.mapei.com
                                                  E-mail: mapeivenezuela@hotmail.com
                                                  Plant in Caracas
MOBINO OFFICES - Lucerne - Switzerland
Parquet laid using ULTRABOND P990 1K on substrates
treated with ECO PRIM PU 1K
OUR COMMITMENT TO THE ENVIRONMENT
AND SAFETY
MAPEI’s concern for the environmental impact of its products is more
than a trend. It is a fundamental part of our philosophy, corporate
                                                                             Complete range of
commitment and industrial responsibility. This is why MAPEI is
committed to formulating water dispersion or solvent-free products
and has developed the ECO line. This line contains a vast range of
products with very low emissions of volatile organic compounds
                                                                             MAPEI solutions
(VOC) for all types of floor and wall coverings.
                                                                             MAPEI's adhesives and chemical products for construction can
Furthermore, MAPEI dedicates its research towards certified quality          improve the quality of life of whoever chooses the MAPEI brand,
and safety. This trend began in 1992 with Responsible Care, the              enhancing the aesthetics, the comfort and the safety of the
international chemical industries’ commitment to sustainable                 environment in which we live. MAPEI's products are in fact
development promoted in Italy.                                               everywhere in our homes, be it underneath our floors, in concrete
                                                                             pillars, or in historic buildings, often invisible, but nonetheless
                                                                             fundamental in both a figurative and literal sense. As well as solidity
                                                                             and stability, a product portfolio encompassing a vast range of
                                                                             performance characteristics and colours offers security and
                                                                             inspiration for architects and project planners who strive to create
                                                                             safer and ever more attractive structures.
                                                                             The products that are supplied to jobsites throughout the world by
                                                                             authorized MAPEI distributors are subdivided in five product lines:
OUR COMMITMENT TO QUALITY
Ever since 1995 MAPEI S.p.A. applied Quality System, certified               1. Ceramic tiles and stone materials line
according to the ISO 9001 standard, and was one of the first                 2. Resilients, textiles and wood line
companies to be awarded the certification in compliance to the new           3. Building and major construction line
version – ISO 9001 : Vision 2000.                                            4. Admixtures for concrete line
This result evidences the MAPEI organisation’s commitment to                 5. Cement additive line
develop all its activities, in particular the development of its products,
sales, production and technical assistance. MAPEI’s objectives are:          The MAPEI production line is made up of the following categories:
                                                                             • Adhesives for floors, ceramics and natural stoneware
            – to meet customer needs and support their activities;           • Grouts and elastic sealants
                                                                             • Adhesives for the installation of resilient, textile and wood floor and
            – to continually improve products and services to
                                                                               wall coverings
              maintain them at the highest market levels;
                                                                             • Products for the preparation of all substrates for building
            – to improve the company’s efficiency.                           • Special hydraulic binders
                                                                             • Ready-mixed mortars and special products for the repair of
Customer service, the knowledge and application of the best                    concrete structures
technologies available, the determination to carry out work well are         • Mortars and binders for the recovery of stone masonry
the distinctive characteristics of the MAPEI organisation.                   • Admixtures for mortars and concrete
Following the MAPEI General Management’s lead, the other Group               • Waterproofing compounds and anti-humidity agents
companies have obtained Quality Management System certifications             • Soundproofing systems
and the other companies will also soon achieve them.                         • Smoothing agents and protective compounds for outside walls
                                                                             • Polystyrene foam heat insulation systems
OUR COMMITMENT TO RESEARCH                                                   • Cement additives
Every year MAPEI invests 5% of its annual turnover and employs               One product, one data sheet
12% of its workforce in research. MAPEI’s seven central research             Collected in five different binders according to product range, the
laboratories in Milan in Italy, Laval in Canada, Tolosa in France,           MAPEI data sheets are available in numerous different languages and
Deerfield Beach in the USA, Sagstua in Norway, Villadossola in Italy         represent a comprehensive source of documentation on single MAPEI
(Vinavil) and Wiesbaden in Germany (Sopro) are concrete examples             products both for on-site use and cement works. As well as being
of MAPEI’s constant commitment high quality technology of its                an exhaustive user guide, they also serve as a detailed technical
products.                                                                    and physio-chemical profile of the products supplying essential
Production is another of MAPEI’s strong points. The Group now                information on safety and accident prevention.
counts 50 subsidiaries with 47 production facilities in operation in the     This information is also published on safety sheets and product
5 continents producing more than 16,000 tons a day of finished               packaging. The data sheets are also available on CD and on the MAPEI
products and just as many tons come in as raw material necessary for         home page (www.mapei.com).
manufacturing more than 1.000 different products such as adhesives,
sealants, mortars, admixtures, latexes, etc. that make up the
complete range of MAPEI products.

OUR COMMITMENT TO YOU
MAPEI has a large technical-sales network in all the most important
countries of the world and offers an excellent technical service and
consultancy on the job-site. MAPEI also offers a large range of
documentation rich in technical details from application to
specifications. All this is available on CD rom.
Furthermore, MAPEI offers all this information and more (company
history, institutional information and products available) on its
website that links all the Group subsidiaries. The address is always
the same: www.mapei.com.
                                           AG. MORE LIGHT/BETA
 DISTRIBUTOR




                                        C.P. MK 689830 - (GB) 1/2008




Mapei S.p.A.
Via Cafiero, 22 - 20158 Milan - Italy
Tel. +39/02 37673.1
Fax +39/02 37673.214
www.mapei.com
mapei@mapei.it
Mapei S.p.A.
Via Cafiero, 22
20158 Milano
Tel. +39/02 37673.1
Fax +39/02 37673.214
www.mapei.com
mapei@mapei.it

				
DOCUMENT INFO
Shared By:
Categories:
Tags:
Stats:
views:56
posted:8/1/2011
language:English
pages:48