VIEWS: 90 PAGES: 22 POSTED ON: 7/16/2011
Online Building Plan Sanction User Manual MCD Architect Municipal Corporation of Delhi Online Building Plan Sanction User Manual To Prepare Building Plan Template Version 1.0 Confidential to MCD Page 1 Online Building Plan Sanction User Manual MCD Architect Table of Contents 1. INTRODUCTION 3 2. INTENDED AUDIENCE 3 3. REFERENCES 3 4. DEFINITIONS AND ACRONYMS 3 5. PREREQUISITE 4 6. PROCESS FLOW - PENDING 5 7. FILE NAMING CONVENTION - PENDING 6 8. GENERAL CONDITIONS 7 9. RESIDENTIAL – PLOTTED DEVELOPMENT 10 Confidential to MCD Page 2 Online Building Plan Sanction User Manual MCD Architect 1. Introduction This document provides guidelines and instruction to the public who wish to avail Online Building Plan Sanction Service. Building Plan in *.DWG format to be prepared and uploaded for the Bye-law validation and get it sanctioned by MCD Before preparing please download the latest version of the User Manual, Template and adhere to the same. 2. Intended Audience Architects Engineers Supervisor Draughtsman MCD Building Plan Sanction Authority 3. References S. No References 1 Building Bye-Law 1983 2 Master Plan of Delhi 2021 4. Definitions and Acronyms Abbreviation/Term Description MCD Municipal Corporation of Delhi BBL Building Bye-Law 1983 BP ID Build Plan ID – System generated ID while applying for Building Plan Sanction MPD Master Plan of Delhi 2021 NA Not Applicable Man. Mandate – to be present in the DWG and to be validated Min. Minimum Max. Maximum Confidential to MCD Page 3 Online Building Plan Sanction User Manual MCD Architect M Meters OBPS Online Building Plan Sanction sq. m Square Meter NR No restriction FAR Floor Area Ratio = Total covered area of all the floor x 100 / Plot Area DU Dwelling unit ECS Equivalent Car Space 5. Prerequisite Knowledge in BBL and MPD Building Plan / Architectural Drawing Creation experience AutoCAD experience Confidential to MCD Page 4 Online Building Plan Sanction User Manual MCD Architect 6. Process Flow - Pending Registration with http://www.mcdonline.gov.in/ To avail OBPS facility Confidential to MCD Page 5 Online Building Plan Sanction User Manual MCD Architect 7. File Naming Convention - Pending At the time of applying for Online Building Plan Sanction BP ID (8 digit) will be generated. Ex: 24128769 For each time uploading a version ID will be generated by the system Ex: 01 – First time uploading 02 – Second time uploading S. No. File Name Remarks 24128769_05_ Confidential to MCD Page 6 Online Building Plan Sanction User Manual MCD Architect 8. General Conditions 1. Draw the building plan using AuotCAD latest version and upload in DWG format. 2. Download template from the link – already required layer are available 3. Download samples from the link for more understating 4. Use Model space to draw 5. Set units as follows 6. Draw the features in 1:1 scale 7. Should be drawn with limits Lower Left Corner: 0,0 Upper Right Corner : 99999,99999 8. No space allowed after or before the comma (,) 9. No space allowed after or before the quote (‘) 10. To represent area (Ex, Plot, Room, Floor) use only closed Poly line Option1: In case of more than 4 sides Command: PLINE Should use option ‘Close’ to complete the area Confidential to MCD Page 7 Online Building Plan Sanction User Manual MCD Architect Option 2: Incase of 4 sided area Command: RECTANG 11. Use only specified layers and specified syntax to represent the features of the building plan 12. Should not use other than specified layers 13. In case more than one floor plan is identical, can be shown as single plan use the Confidential to MCD Page 8 Online Building Plan Sanction User Manual MCD Architect Confidential to MCD Page 9 Online Building Plan Sanction User Manual MCD Architect 9. Residential – Plotted Development Draw the features and related texts in the respective layers only. Layer Type Attribute Condition Closed PLINE / MCD_Balcony RECTANG Balcony code,Balcony No,Rail Height (Ex: BO,3,1.3) MCD_Balcony Text BO-Balcony Closed PLINE / To represent and group plan, elevation, section MCD_Box RECTANG related to one building. Closed PLINE / To draw on the site plan to represent outer most MCD_Boundary RECTANG edge of the boundary wall Wall height, wall side code, description, type of street (Ex: 1.5 m,F,BOUNDARY HEIGHT,FSTREET) F - Front side height S1 - side1 height S2- Side2 height RR - Rear side height FSTREET - Front street Text should have been marked all the 4 sides of the MCD_Boundary Text SRVSSTREET - Service street boundaries i.e. should have 4 texts per plot. Closed PLINE / MCD_Building_Area RECTANG To draw building on the site plan Confidential to MCD Page 10 Online Building Plan Sanction User Manual MCD Architect Layer Type Attribute Condition MCD_Building_Area Text Building No (Ex: B-1) Closed PLINE / MCD_Canopies RECTANG Canopy code, Canopy No, clearance Height (Ex: MCD_Canopies Text Can,1,2.2) Closed Each straight corridor should be represented by a PLINE / Closed PLINE / RECTANG i.e. two polygon is required MCD_Corridor RECTANG to represent 'L' shaped corridor MCD_Corridor Text Corridor Code, Corridor no (Ex: COR,1) Corridor, Lobby can be drawn Closed PLINE / MCD_INTERIOR_Courtyard RECTANG Building No, Interior Courtyard No, Courtyard Courtyard Height Should measured from road center MCD_INTERIOR_Courtyard Text Height (ex: B-001,01,10) line. If cupboard projected inside rooms no limit of length. If cupboard projected outside into open space no limit of length. If cupboard projected outside into open space and Closed overlap with setback then Max length of the PLINE / cupboard would be 2m MCD_Cupboard RECTANG Vertical partition distance would me max 1.5 Confidential to MCD Page 11 Online Building Plan Sanction User Manual MCD Architect Layer Type Attribute Condition Cupboard code, Cupboard No, Projected yes or projected no ,partition distance (Ex:CUP,1,PN,0.75) PY-Projection Yes (Consider only when overlap with setback) MCD_Cupboard Text PN-Projection No D1 info can be read from MCD_Door_Table W1 info can be read from MCD_Win_Table V1 info can be read from MCD_Win_Table Door type, Door number (Ex: D1,2) To be dimensioned for Floor Ht dimensions, RCC, D – Door for exit Plinth dimensions, Stair hand rail height, Ramp hand DB – Door for Bathroom, Closet, stores rail, Stair head room height, Dia of Spiral Stair Window - Window Number (Ex: W1,2) DIMLINEAR command should be used to draw the MCD_Dim Dimension Ventilation – Ventilation Number (Ex: V1,3) DIM Closed PLINE / Mark the Door number in MCD_Dim and Dorr MCD_Door RECTANG dimension in MCD_Door_Table Refer to the sample DWG and use the table in the MCD_Door_Table Table Contains Door related info template Closed PLINE / Dwelling Area polygons should be within the MCD_Dwelling_Area RECTANG respective floor plan MCD_Dwelling_Area Text Dwelling no (Ex:DU-02) Closed Should not be drawn inside the MCD_Flooe_Area, so PLINE / To draw in the plan to represent width and one that it will not be counted in Gound Coverage Area MCD_FireExit_Ext_Stair RECTANG flight i.e. draw one polygon / flight and FAR To draw in the plan to represent number of Number of raisers / flight and Tread will be derived MCD_FireExit_Ext_Stair Line steps based on the space and count Confidential to MCD Page 12 Online Building Plan Sanction User Manual MCD Architect Layer Type Attribute Condition Fire exit code, exit no, raiser height (Ex: MCD_FireExit_Ext_Stair Text FIRE,2,0.15) Closed PLINE / MCD_Floor_Area RECTANG Building No, Floor code, Floor No (Ex: B- 001,O,F-2'4'6'8) B - Basement S - Stilt M – Mezzine / Service G - Ground Identical floor plans can be represented in a single T - Terrace plan with floor code - O - Other Floors. P - Plinth Should have separate plan for Basement, Stilt, MCD_Floor_Area Text O - Other Floors Mezzine / Service, Ground, Plinth and Terrace Closed PLINE / Each floor should be represented by a separated MCD_Floor_Height RECTANG polygon Building No, Floor code, Floor No (Ex: B- 001,O,F-2) B1 –Portion of Basement above ground level B2 – Portion of Basement below ground level This is typical sectional view B3 – Second basement which would be If floor code other than 'O' is used floor number completely below ground level would be zero (0). S - Stilt If there is no basement only then Plinth would be M – Mezzine / Service present G - Ground Plinth should be measured from surrounding ground T - Terrace level P - Plinth Mark dimension of Floor Ht dimensions, RCC MCD_Floor_Height Text O - Other Floors - from F-1 to F-n thickness, Plinth in MCD_Dim layer Confidential to MCD Page 13 Online Building Plan Sanction User Manual MCD Architect Layer Type Attribute Condition If basement used only for House hold storage and Parking, put 'HOUSE HOLD STORAGE AND PARKING' to exclude from FAR. In case of mixed use of basement do not put 'HOUSE HOLD STORAGE AND PARKING' and will be counted MCD_Basement_HHS_Parking Text SYNTAX: HOUSE HOLD STORAGE AND PARKING for FAR Closed PLINE / MCD_Garage RECTANG Garage code, Garage No, Head room height, Garage Plinth Height, Lock-up/Un Lock-up, Parking type, Floor No(Ex: GRG,2,3.2,1.7,LU,PR- PARKING,F-1) LU - Lock-up ULU - Un Lock-up PU-PARKING - Public parking PR-PARKING - Private parking MCD_Garage Text Floor no - from F-1 Lock-up parking Garage will be counted for FAR Draw the average gound level / center line of the MCD_Gline_Cline_Street Line adjoining street in sectional view Closed PLINE / Mark height of head room under the stair in MCD_HeadRoom_Height RECTANG MCD_Dim layer Closed PLINE / MCD_Ledge_Tand RECTANG Ledge code, Ledge no, Height from floor MCD_Ledge_Tand Text level(Ex: LDG,1,2.2) Confidential to MCD Page 14 Online Building Plan Sanction User Manual MCD Architect Layer Type Attribute Condition Closed PLINE / MCD_Lift RECTANG Lift well to be drawn in the plan MCD_Lift Text LIFT code, Lift No(Ex: LIFT,2) Closed PLINE / MCD_Loft RECTANG Need to represent on the plan Loft code, Loft no, Distance from ceiling (Ex: MCD_Loft Text LO,1,1) Following items can be captured which will not be counted for Coverage / FAR A Mamti over stair-case on top floor Machine room for lift on top floor Rockery, well and well structures, plant nursery, water pool, swimming pool, (if uncovered) platform round a tree, tank, fountain, bench, Chabutra with Closed open top and enclosed sides by walls, gate, slide PLINE / swing, overhead water tank on top of building, open MCD_Not_Covered_FAR RECTANG shafts . Text related to the structure / object like well, water MCD_Not_Covered_FAR Text pool, tank etc which is not covered under FAR Closed To draw on the plan view of the terrace as polygon to MCD_ParapetWall PLINE / represent outer most edge of the parapet wall Confidential to MCD Page 15 Online Building Plan Sanction User Manual MCD Architect Layer Type Attribute Condition RECTANG Parapet wall height, Description (Ex: 1.5 The height should be considered for all sides of MCD_ParapetWall Text M,PAPAPET WALL) parapet wall. Closed PLINE / MCD_PARKING RECTANG CAR PARKING SHORT FORM, PARKING CODE, PARKING NO (EX: CP,GR,1) OP OPEN GR GROUND FLOOR BS BASEMENT ML MULTI LEVEL Parking space left in the Garage / Stilt need to be MCD_PRAKING TEXT AML AUTOMATED MULTI LEVEL mentioned as “GR” Closed Space which cannot be used for parking like lift, stairs, PLINE / swing pool etc inside a MCD_PARKING polygon need MCD_PARKING_NOTUSEABLE RECTANG to be drawn in this layer. MCD_PARKING_NOTUSEABLE Text Feature name (Ex: LIFT) Closed Each straight passage should be represented by a PLINE / polygon i.e. two polygon is required to represent 'L' MCD_Passage RECTANG shaped passage MCD_Passage Text Passage code, Passage no (Ex: PAS,1) Closed PLINE / MCD_Pergola RECTANG Confidential to MCD Page 16 Online Building Plan Sanction User Manual MCD Architect Layer Type Attribute Condition Pergola code, Pergola no, Pergola Height (Ex: MCD_Pergola Text PER,1,2.1) Closed PLINE / MCD_Pergola_Void RECTANG Closed PLINE / MCD_Plot_Area RECTANG Should have only one plot boundary MCD_Plot_Area Text Depth in M (Ex: 127) Put the max. depth Hand rail for Stair, Ramp, Balcony, Fire stair should be drawn in the sectional view and in the MCD_DIM MCD_RAIL Line mark the height of the hand rail. Closed PLINE / MCD_Ramp RECTANG To be drawn in the plan to represent width. To be drawn in the sectional view to represent of MCD_Ramp Line hand rail Ramp code, Ramp no, Open / Closed, Slope (Ex: RMP,1,OP,1:10) OP – Open MCD_Ramp Text CL – Closed Mark height of Ramp hand rail in MCD_Dim layer Closed PLINE / MCD_Room RECTANG Confidential to MCD Page 17 Online Building Plan Sanction User Manual MCD Architect Layer Type Attribute Condition Room Code, Room Number, Room Height (Ex: KD-2-3) K-Kitchen KD-Kitchen and Dining PAN - Pantry B-Bathroom WC-Water Closet BWC-Bath and Water Closet BED-Bed Room SR-Store Room MCD_Room Text OT-Other Rooms Closed PLINE / All the sectional info should be drawn inside MCD_Section RECTANG MCD_Section MCD_Section Text section name (ex: section-A-A) Closed PLINE / MCD_Servant_Area RECTANG Servant Quarter code, Servant quarter no, Floor No (Ex: SE,1,F-1) MCD_Servant_Area Text Floor no - from F-1 Closed PLINE / MCD_Setback_Area RECTANG Setbacks should be have only 4 polygons Confidential to MCD Page 18 Online Building Plan Sanction User Manual MCD Architect Layer Type Attribute Condition Setback code, width of setback in Meters( Ex: F,5) F - Front R - Rear RS - Right Side MCD_Setback_Area Text LS - Left Side MCD_Spiral_Stair Line / Arc Mark the DIA of the spiral stair in MCD_Dim layer Closed PLINE / To draw in the plan to represent width and one flight MCD_Stair RECTANG i.e. draw one polygon / flight Number of raisers / flight and Tread will be derived based on the space and count To draw in the plan to represent number of steps & MCD_Stair Line hand rail in sectional view Stair code, stair no,raiser height (Ex: STR,1,0.15) MCD_Stair Text Mark height of Stair hand rail in MCD_Dim layer Closed PLINE / MCD_Stair_Landing RECTANG Draw in the plan view to represent the landing Closed PLINE / MCD_Street RECTANG Front street should abut to the Plot_Area Confidential to MCD Page 19 Online Building Plan Sanction User Manual MCD Architect Layer Type Attribute Condition Street code, Existing/Future, Street Name / No, Width in M (Ex: F,EX,Gandhi Street, 35) F - Front street O - Other street EX - Existing MCD_Street Text FU – Future Closed PLINE / MCD_ Shaft RECTANG MCD_ Shaft Text Building No, Shaft No (ex: B-001,01) Closed PLINE / MCD_Watchman_Cabin RECTANG Closed PLINE / MCD_Weather shade RECTANG To be represent on plan Shade code, shade no, height from finished MCD_Weather shade Text floor level(Ex: WS,1,2) Refer to the sample DWG and use the table in the MCD_Win_Table Table Contains windows and Ventilation related info template Draw Windows and Ventilation Closed Mark the window / ventilation number in MCD_Dim PLINE / and window / ventilation dimension in MCD_Window_Vent RECTANG MCD_Win_Table Confidential to MCD Page 20 Online Building Plan Sanction User Manual MCD Architect Confidential to MCD Page 21 Online Building Plan Sanction User Manual MCD Architect Confidential to MCD Page 22
"MCD Engineering SRS"