Docstoc

Safety - 1774

Document Sample
Safety - 1774 Powered By Docstoc
					                  T. F. GREEN AIRPORT IMPROVEMENT PROJECT
                              PROCEDURES MANUAL
        0          IV                  600 - Safety                                600
       Rev.      Chapter                  Series                                 Section
     5/12/95                             Safety                                   1 of 3
       Date                                Title                                  Pages



1.      Overview

        A.     Gilbane Building Company has developed, implemented and is monitoring
               conformance to the T. F. Green Airport Improvements Project Safety Plan
               (Reference Exhibit 600.1). The objective of the plan is to provide an
               outline of safety standards to be conformed to while performing work on
               the jobsite. Bidders/Contractors are required to reference the manual
               during the estimating, planning and performance of their work on the
               project.



2.      Development

        A.     Gilbane Building Company,has assembled the Project Safety Manual for
               T.F. Green Airport utilizing information from and/or regulations created
               by:

               1.    The Occupational Safety and Health Administration (OSHA) and
                     other Federal Agencies.
               2.    State and local regulations.
               3.    Incorporation of information and requirements developed and
                     instituted by industry organizations relating to safe construction
                     practice.

               4.     Safety programs developed and utilized on other Gilbane
                      construction projects.

3.      Implementation

        A.     The Project Safety Manual has been incorporated into Volume I of all
               Trade Contractor contract documents and will be used to solicit
               proposals for all contract work on the project.

        B.     Safety is an important part of the procurement process and Trade
               Contractor selection. At the time bids are received the following criteria
               must be satisfied in order for a contractor to be considered a responsive
               bidder:
                 T. F. GREEN AIRPORT IMPROVEMENT PROJECT
                             PROCEDURES MANUAL
        0         IV                  600 - Safety                                600
       Rev.     Chapter                  Series                                 Section
     5/12/95                             Safety                                  2 of 3
      Date                                Title                                  Pages



               1.    Provide information requested by the Contractor Qualification
                     Form and Evaluation Criteria (Exhibit 600.2).

               2.    Co-sign the management statement included in the safety
                     program signifying their company's endorsement to the Safety
                     Plan while performing work on the project. Other signatory parties
                     on the statement include RIAC's Project Manager, Irwin D.
                     Crowley, Gilbane Building Company's Project Executive, Lou
                     DeISesto, Project Manager, William G. Bryan and Project Safety
                     Manager/Safety Coordinator, John D. Mello.

        C.     Gilbane Building Company will administer the Project Construction/Safety
               Orientation when a contractor begins work on the construction site. The
               orientation will be held on a regular basis at the Project Teams
               Conference Room. The orientation will include a video presentation
               created to highlight concerns specific to the Airport Project, and provide
               an overview of the safety program. Stickers will be issued to all
               employees who have attended the orientation, and will be affixed to their
               hard hats.

        D.     Gilbane Building Company will develop a Safety Incentive Program which
               provides rewards to workmen when project safety goals are met. The
               program will be submitted to RIAC for their review and approval prior to
               implementation.

4.      Monitoring Conformance
        A.   Gilbane monitors on site construction activities for conformance to the
             Project Safety Manual. Contractor conformance is the direct
             responsibility of Gilbane's Project Superintendents and Project Safety
             Manager. In addition, the entire project team is responsible to promote
             a safe work environment by monitoring and correcting unsafe working
             conditions observed on the construction site. Monitoring efforts include
             but are not limited to:
              1.    On site inspections and observations.

               2.     Gilbane's Project Safety Manager will oversee weekly jobsite safety
                      meetings with the contractors safety representatives. The meetings
                      will focus on particular safety issues and/or review safe
                T. F. GREEN AIRPORT IMPROVEMENT PROJECT
                            PROCEDURES MANUAL
   0             IV                  600 - Safety                             600
  Rev.         Chapter                  Series                              Section
5/12/95                                Safety                                3 of 3
  Date                                   Title                               Pages



                  work practices related to future work activities. Meeting minutes will
                  be kept and distributed to trade contractors.

          3.      Review of Trade Contractor safety plans and MSDS programs
                  which are required before work starts on site.
          4.      Collection and review of weekly trade contractor tool box talks.
          5.      Monthly inspections by representatives of the insurance
                  underwriters, Willis Corroon, and the Gilbane Project Safety
                  Manager.

          6.      Periodic inspections by Gilbane regional and corporate safety
                  managers.

          7.      Additional monitoring efforts are described in the Project Safety
                  Plan.

   B.     At the Construction Managers discretion Gilbane Building Company will
          stop the work of any contractor who is using unsafe work practices.
          Violations will be reported to the Gilbane Superintendent and the
          Contractor. Repeat violations and/or non-conformance to safety
          requirements may result in written reprimands, withholding of payment
          (reference Section 211 for further information) and/or removal of
          personnel from the jobsite.
                               Gilbane Building Company

                CONSTRUCTION MANAGEMENT SAFETY PROGRAM


     Project: Theodore Francis Green State Airport            Job No: 1774
     Subject: Safety/Security Rules and Regulations           Date: October 24, 1994
   Approval: William Bryan, Project Manager                   Revision:      4




       PROJECT SAFETY & MEDICAL RULES & REGULATIONS

The safety, health, medical rules and regulations contained herein are not all inclusive. All U.S.
Department of Labor, Occupational Safety and Health Administration (OSHA), U.S. Department
of Transportation, Federal Aviation Administration (F.A.A.), Federal Highway Administration
(F.H.W.A.), Federal, State, local and other legal standards not specifically referenced in these
rules, regulations and policies shall apply when applicable.




       (CHANGES ARE NOT TO BE MADE TO THIS DOCUMENT WITHOUT
          PRIOR APPROVAL OF THE PROJECT SAFETY DEPARTMENT)




cBCorrFCn77a:ma/9s                           tv.s-1                                Exhibit 600.1
        Subject: (         Safety, Rules and Regulations      I        Page 2 of 4611



IF I.    FOREWORD
         A.          MANAGEMENT STATEMENT
         B.          PROJECT SUMMARY
         C.          GENERAL TERMS AND CONDITIONS


II.       CONTENTS
          1.0 TRADE CONTRACTOR RESPONSIBILITY
          2.0 PRE-CONSTRUCTION SAFETY MEETING
          3.0 INSTRUCTION AND TRAINING
          4.0 RECORD KEEPING
          5.0 FIRE PREVENTION
          6.0 THIRD PARTY SAFETY INSPECTIONS
          7.0 CONSTRUCTION EMERGENCY ACTION PLAN
          7.1 SECURITY
          7.2 TRAFFIC CONTROL
          7.3 ENTRANCE ROAD
          7.4        GUIDELINES FOR ACCESS TO THE SITE AND WORKING INSIDE A.O.A.
          8.0        PROJECT SAFETY RULES/REGULATIONS GUIDELINES
          8.1        CLOTHING REQUIREMENTS
          8.2        PERSONAL PROTECTIVE EQUIPMENT
          8.3        SIGNS, SIGNALS, BARRICADES AND LIGHTS
          8.4        RIGGING EQUIPMENT
          8.5        HAND & POWER TOOLS
          8.6        COMPRESSED GAS CYLINDERS
          8.7        SCAFFOLDS
          8.8        JOBSITE TRANSPORTATION RULES
          8.9        CRANES AND DERRICKS
          8.10       TOWER CRANE SPECIFICS
          8.11       EQUIPMENT & MOTOR VEHICLES
          8.12       ELECTRICAL
          8.13       LADDERS
          8.14       FLOOR & WALL OPENINGS & STAIRWAYS

cBCorrFCn77a:mams                                    Iv.s-2           Exhibit 600.1
       Subject:             Safety, Rules and Regulations                              Page 3 of 46



         8.15      EXCAVATIONS & TRENCHING
         8.16      STEEL ERECTION
         8.17      CONFINED AREAS AND/OR SPACES
         8.18      HOUSEKEEPING
         8.19      GENERAL
         8.20      MEDICAL SERVICES
                    .1    TRADE CONTRACTOR RESPONSIBILITIES
                    .2    FIRST AID & MEDICAL PROCEDURES

                          .1       FIRST AID (MINOR CUTS, SCRATCHES, BRUISES, ETC.)
                          .2       MEDICAL CASES (NOT REQUIRING AMBULANCE SERVICES)
                          .3       EMERGENCY CASES (REQUIRING AMBULANCE SERVICES)
         8.21       DEATH (OR HOSPITALIZATION OF FIVE OR MORE EMPLOYEES)
         8.22       SAFETY LOCK & TAGGING
         8.23       DEMOLITION
         8.24       HEATING & VENTILATING
         8.25       ENVIRONMENTAL HAZARDS
         8.26       RIGHT TO KNOW
         8.27       ASBESTOS HANDLING
         8.28       BLASTING
         8.29       INDUSTRIAL X-RAY RADIOGRAPHY
         8.30       HAZARDOUS MATERIAL/VOLATILE LIQUIDS




GBCo/t'FG/17742/14/95                                       IV.B-3                    Exhibit 600.1
      Subject:         Safety, Rules and Regulations               Page 4 of 46




                                                  FORMS



FORM                   TITLE                                       SECTION
   1.   DAILY EXCAVATION/TRENCHING LOG                              8.15.1
   2.   SAFETY ASSIGNMENT NOTICE                                    1.0
   3.   SAFETY SURVEY                                               1.0
  3A.   SAFETY SCORE SHEET                                          1.0
   4.   ACCIDENT INVESTIGATION FORM                                 8.20
   5.   NOTICE OF SAFETY VIOLATION                                  1.0
   6.   SAFETY MEETING MINUTES                                      1.0.12
   7.   INJURY ON THE JOB                                           8.20
   8.   SAFETY TRAINING                                             3.0
  8A.   SAFETY TRAINING (TOOL BOX TALK)                             3.0
   9.   EMERGENCY PHONE NUMBERS                                     1.0
10.CRANE INSPECTION REPORT                                                 8.9
11.CRANE CRITICAL LIFT CHECKLIST                                           8.9
12.     CUTTING/WELDING HOTWORK PERMIT                              8.19
13.     IN CASE OF FIRE
14.     ASSURED EQUIPMENT GROUNDING CONDUCTOR PROGRAM
8.12
        .I RECORD OF TEST
        .2 TEST CRITERIA
 15.    RELEASE: GENERAL                                              1.0
 15A.   RELEASE: ELEVATOR                                             1.0
 15B.   RELEASE: SCAFFOLD                                             8.7
 16.    EMPLOYER'S FIRST REPORT OF INJURY FORM                        8.20
 17.    CONFINED SPACE ENTRY PERMIT AND PROCEDURES                    8.17




                                           ATTACHMENTS


                        F.A.A. ADVISORY CIRCULAR 150/5370-2C
                       (AIRPORT SAFETY DURING CONSTRUCTION)

                        F.A.A. ADVISORY CIRCULAR 150/5210-SB
                    (VEHICULAR MARKING AND LIGHTING FOR SAFETY)




cBConTcn774:m4i9s                                      Iv.B-4     Exhibit 600.1
   A.               MANAGEMENT STATEMENT

   Gilbane Building Company management at all levels are dedicated to assuring that its employees
   and others are provided a safe and healthy working environment on its project sites. In order to
   succeed, each Gilbane Building Company Construction Supervisors) must implement safety and
   accident prevention measures and demonstrate leadership which will elicit a safety first response
   from everyone on site. Each Trade Contractor/employee must include safety on an equal basis
   with cost, productivity, quality and schedule. Safety must be an integral part of our day-to-day
   operations since it will ensure that we meet and/or exceed OSHA standards, state and local
   regulations, policy and the Company's commitment to safety.

   This safety program has been prepared to assist each project job site employer/Trade Contractor
   in satisfying its contractual responsibilities, in such a manner that a safe, efficient operation is
   assured. For additional advice and assistance each employer should consult with the Project
   Safety Manager, its own safety organization, insurance carrier or similar available source.

   This material must not be considered to be all inclusive as to the hazards that might be
   encountered, safe practices that should be performed, or safe conditions that should be maintained
   during the course of this project.

                                   Gilbane Building Company

t.~~.
         Louis DelSesto                William G. Bryan                      John D. Mello
        Project Executive              Project Manager                   Project Safety Manager

                              RHODE ISLAND AIRPORT CORPORATION


                                       Irwin D. Crowley
                                       Project Manager

    The bidder shall properly execute this sheet to certify he has thoroughly reviewed this
    Construction Management Safety Program and will comply with all rules and requirements
    contained therein if awarded the contract.

    Accepted By:



     Title:                                                  Company -




    GBCo/TFG/1774:1 I R4I94                       I V. B-$




                                                                                              Exhibit 600.1
11
11   Subject:           Safety, Rules and Regulations                                Page 6 of 46




           PROJECT SUMMARY

           All persons who come into the work area, for any reason during construction, will be
           required to comply with the established safety regulations that govern the project.

           Trade Contractors are committed by contract to observe and comply with all
           applicable safety/security regulations and procedures. Each Trade Contractor will
           participate in the Project Safety/Security Program, hereafter referred to as the
           "Program".

            If the Construction Manager find Trade Contractor areas of work or individuals being,
            or acting in noncompliance with the Occupational Safety and Health Act of 1970
            (OSHA), as amended, or any other applicable regulations, he shall have the authority
            to order immediate correction and cessation of the noncompliance occurrence.
            Non-compliance with Project Safety Regulations will be grounds for Trade
            Contractor dismissal and/or employees) being forbidden entry onto the project.
            All costs of correction shall be borne by the Trade Contractor deemed responsible.
            The Construction Manager's decision of responsibility shall be final.

            Periodic safety meetings will be held, as necessary and as directed by the Construction
            Manager's Project Superintendent. All Trade Contractors actually working on the
            project must delegate one representative to attend this meeting who is authorized and
            responsible to fulfill and maintain all Program requirements of the Trade Contractor.


            Nothing contained herein, however, shall serve to relieve the Trade Contractor of his
            liabilities and/or obligations under the "Occupational Safety and Health Act of 1970"
            and all additions and revisions thereto, as well as all other applicable Federal, State
            and Local requirements.


            GENERAL TERMS AND CONDITIONS

            1.     SPECIAL SITE CONDITIONS

                   a.      TRAFFIC

                           1.       Vehicular traffic to and from the project site will be required
                                    to pass through specified access points and/or routes. Refer to
                                    the Site Utilization Plan.
                           2.       Security Requirements-All construction trade personnel will be
                                    required to attend a Project Construction Operations/Safety
                                    Orientation prior to commencing employment on the project.
                                    Any other personnel must be accompanied by trained personnel
                                    while on the project site.


csconTcim4:zn4/9s                                  Iv.B-6                           Exhibit 600.1
       Subject:              Safety, Rules and Regulations                                 Page 7 of 46



                               3.        The following personnel require photo identification badges
                                         issued by the Airport Security Office:

                                         a.       Gilbane Building Company Field Personnel
                                         b.       Traffic Control and Security Personnel
                                         c.       Airfield Trade Contractor Superintendents

                        b.     TRADE CONTRACTOR TRADE EMPLOYEES

                               1.        The Construction Manager will administer the Project
                                         Construction Operations/Safety Orientation which will be held
                                         in the Construction Manager's field office.
                               2.        All new employees must attend this 30 minute orientation prior
                                         to being permitted to work on the project.
                               3.        Trade Contractors must notify the Construction Manager at
                                         least twenty four (24) hours prior to new personnel coming on
                                         site for orientation.
                               4.        Badges issued by Airport Security may be required for
                                         personnel working in the Airfield Operational Area (A.O.A.).
                                         In the event a badge is required the trade employee must take
                                         and pass the required airport provided FAA Training Program.
                                         If an individual loses a badge issued to him/her, they will not
                                         be allowed to work and reissuance of a badge is at the
                                         Airport's discretion subject to applicable F.A.A. requirements.
                               5.        All Trade Contractors will be required to provide hard hats of
                                         a uniform color to their personnel. The Trade Contractors
                                         name and/or logo will appear on all hats and be identifiable
                                         from a distance of at least twenty-five (25') feet. The
                                         employees full name must also be displayed on the hard hat.

                        c.     JOBSITE VISITORS/DELIVERIES

                                1.       All visitors must sign in at the Construction Manager's field
                                         office and must be accompanied by Trade Contractor personnel
                                         while on site.
                                2.       Any Trade Contractor who, in the opinion of the Construction
                                         Manager, fails to abide by the requirements of this plan, will
                                         be terminated.
                                3.       Any Trade Contractor employee who, in the opinion of the
                                         Construction Manager, fails to abide by the requirements of
                                         this plan will be removed from the jobsite.
                                4.       Comply with attached F.A.A. Advisory Circular 150/5210-SB
                                         "Painting, Marking and Lighting of Vehicles used on an
                                         Airport" and the Airport's Certification Manual.




GBCo/fFG/1774:2/14/95                                   IV.B-7
                                                                                          Exhibit 600.1
    Subject:        Safety, Rules and Regulations                                  Page 8 of 46



               d.     SITEWORK AND TRUCKING

                      1.        The following shall be adhered to without exception:

                                All vehicles shall be cleaned of all mud and debris before
                                leaving the site. Each Trade Contractor shall be responsible
                                for providing whatever personnel and equipment will be
                                required to perform the required vehicle cleaning throughout the
                                progress of his work. The wheel wash area shall not be used for
                                cleaning out of concrete mix trucks. Cleaning of concrete
                                equipment shall be preformed at locations designated by the
                                Construction Manager. Cleaning shall be conducted in such a
                                manner as to prevent spillage of fluid or concrete to the ground
                                or penetration of existing ground soil. The responsible Trade
                                Contractor shall remove from the site all residue accumulated
                                from the cleaning operations of concrete equipment. All
                                vehicles on the site carrying earthen materials or loose debris
                                shall be loaded in a manner that will prevent dropping of
                                material on-site or public roads, and when necessary, shall have
                                suitable coverings fastened over the load. Trucks bringing
                                earthen materials to the site shall be similarly loaded and
                                covered. The Trade Contractor shall conform to all applicable
                                regulations regarding load limits and be responsible for any
                                costs due to failure to comply with the above.

                                All runways, taxiways, ramps, aprons, and roads will be kept
                                broom clean at all times.

                                All vehicles operating within the A.O.A. must adhere to
                                applicable Federal Aviation Administration (F.A.A.)
                                regulations and the Airport Certification Manual (A.C.M.).

                                Operators of motor vehicles on the T.F. Green State Airport
                                project are required to possess a valid Driver's License and a
                                Commercial Driver's License when required.

                                Trade Contractors) shall have sweeper/vacuum truck, water
                                wagons, calcium chloride, and/or other control measures as
                                required, on site at all times, for dust and Foreign Object Debris
                                (F.O.D.) control. Trade Contractor must prepare and submit
                                their plan of Foreign Object Debris Control to the Construction
                                Manager for approval. The plan must identify locations,
                                personnel, equipment, means and methods to assure that
                                affected areas are kept clean of F.O.D. at all times.

                                 Trade Contractors shall provide and maintain wheel wash
                                 stations during their operations as required by the Construction


csconTcn77a:ma/9s                              Iv.B-8                             Exhibit 600.1
      Subject:       Safety, Rules and Regulations                                 Page 9 of 46


                                Manager. Trade Contractor's operations shall be such as to not
                                create any dust.

                                Aircraft Traffic shall Always have the Right-of-Way over
                                motor vehicle traffic. Stock piling of material inside the
                                A.O.A. is prohibited. No material or equipment can be stored
                                within 250' of the centerline of a runway and 85.5' of taxiways
                                or transitional areas; per F.A.A. regulations. No equipment can
                                be parked or materials stockpiled within the field of the Vortac
                                (VOR).

                                Trade Contractors) doing any work within the A.O.A. are
                                required to submit a plan for approval indicating his/her
                                proposed points and routes of access for material/equipment
                                delivery to the site. No work shall start until this plan is
                                approved by the Airport.

                                The Airport and F.A.A. (Federal Aviation Administration)
                                reserve the right to restrict and/or suspend any operations for
                                reasons of security, weather or safety. Reasonable suspension of
                                this nature shall not be the basis of a claim for extra
                                compensation by the Trade Contractor.

                                In the event that a Trade Contractor's operations require access
                                to or crossing of non-movement or closed taxiways, runways,
                                ramps areas, roads, etc., the Trade Contractor must obtain
                                written approval from the Construction Manager for those
                                activities. In this case the Trade Contractor and the Construction
                                Manager shall conduct two inspections (minimum) per day of
                                the operations and the areas involved. Immediate clean-up of
                                these areas by the Trade Contractor is Mandatory.

                                The Trade Contractor shall provide and maintain proper
                                warnings and detour signs at all pedestrian and vehicular
                                closures, intersections, and along detours, directing traffic
                                around closed portions of roadways, runways, apron, taxiway,
                                etc. He shall, at his own expense, wherever necessary or
                                required, provide and maintain fences, temporary roadways,
                                temporary cross signs, police detail, watchman, warning lights
                                and take such other precautions as may be necessary to protect
                                life and property, and shall be responsible for all damages
                                occasioned in any way by his act or neglect. All barricades and
                                obstructions shall be kept on from one-half hour before sunset,
                                until one-half hour after sunrise.



cBCorrFCn774:zn4ms                             Iv.B-9                             Exhibit 600.1
11   Subject:             Safety, Rules and Regulations                               Page
                                                                                             10 of 46



                     e.     AIRPORT SAFETY

                                      Comply with any applicable F.A.A. regulations and Airport
                                      Certification Manual Requirements. Each Trade Contractor is
                                      required to meet with the Airport and Construction Manager to
                                      review their ongoing construction operations as requested.
                                      Comply with attached F.A.A. Advisory Circular 150/5370-2C,
                                      "Operational Safety on Airports During Construction".
                                      Trade Contractors are required to submit for Airport approval,
                                      their Communications Plan, including radio frequencies, for
                                      approval prior to commencing work.




cBCorrFCiu74:2aaws                                    Iv.B-to                         Exhibit 600.1
        II
        Subject: ~          Safety, Rules and Regulations              I                 Page   I 1 of 46

1.0            TRADE CONTRACTOR RESPONSIBILITIES

1.0.1          The Trade Contractor shall make frequent and regular inspections of the job site by
               a competent safety representative. Unsafe acts and/or conditions noted during
               inspections shall be corrected immediately. The name of Trade Contractor's job site
               safety representative will be provided to Gilbane Building Company and approved by
               the Safety Department, prior to the Trade Contractor starting work at the job site.

1.0.2          Gilbane Building Company will make recurrent safety inspections during construction
               operations. Gilbane's representative will identify any observed unsafe conditions to
               the Trade Contractor's designated (competent) safety representative or superintendent
               who will take appropriate and timely corrective action(s).

1.0.3          Trade Contractor shall take those precautions necessary to protect site personnel,
               visitors, and the public from injury.

1.0.4          Trade Contractor shall instruct each employee on job site in the recognition and
               avoidance of unsafe acts and/or conditions applicable to its work environment to
               control or eliminate injury or illness. Trade Contractor shall enforce the project and
               statutory safety rules on its employees.

1.0.5          Trade Contractor is responsible for providing and requiring the use of appropriate
               personal protective equipment in all operations where there is an exposure to
               hazardous conditions. This shall include, but is not limited to, protection of head,
               forehead, eyes, ears, hearing, breathing, hands, feet, etc. The Trade Contractor shall
               maintain all his project safety records at a location accessible to Rhode Island Airport
               Corporation, Gilbane Building Company and/or its agents.

1.0.6          Trade Contractor is responsible for notifying Gilbane Building Company of any
               unusual flammable, toxic materials, hazardous chemicals or substances that are
               brought or cause to have been brought on job site. Trade Contractor shall provide
               Gilbane Building Company with a copy of Trade Contractor's Hazardous
               Communication Program, Chemical information list, and Material Safety Data
               Sheets) (MSDS) for the chemicals) or substances) intended for use on the site. A
               bookcase, centrally located by Gilbane Building Company will be dedicated for this
               information. Trade Contractor is responsible for maintaining a copy of Trade
               Contractor's Hazard Communication Program, Chemical Information List, and
               Material Safety Data Sheets) on site for Trade Contractor's own reference and
               employee training. The storage, use and disposal of wastes of any hazardous
               chemicals or substances is the responsibility of Trade Contractor.

1.0.7          Trade Contractor is responsible for conforming to OSHA and NFPA standards of fire
               protection and prevention practices. Trade Contractor shall also comply with all fire
               and safety rules and regulations established on the project.

1.0.8          If Trade Contractor fails to correct safety violations, Gilbane Building Company will
               issue the Trade Contractor written notification, outlining safety violations. Failure


GBCo/TFG/1774:2/14/95                                       tv.s-t t                     Exhibit 600.1
        Subject:   I         Safety, Rules and Regulations '                              Page 12 of 46   II
               of the Trade Contractor to abate will result in the removal of the Trade Contractor
               from the project site, and the Company's approved bidders list, or other appropriate
               measures.

1.0.9          OSHA standards will serve as the minimum safety requirements for the project. Any
               job site safety regulations established by the Construction Manager which exceed the
               minimum standards established by OSHA shall take precedence and be incorporated
               in the Trade Contractor's safety program.

1.0.10         All personnel, supervisors, craft trades people, salespersons, visitors, etc., are
               required to wear hard hats and safety glasses or approved eye protection with
               side shields when on the construction site.

1.0.11         Compliance with Federal, State and local laws and regulations is the contractual
               obligation of Trade Contractors working on Gilbane Building Company projects.
               Conflicts between current laws or contractual requirements shall be resolved by
               adhering to the more stringent requirement.

1.0.12         The Trade Contractor shall designate a responsible member of his organization at the
               site whose duty shall be the prevention of accidents. This person shall be the Trade
               Contractor's superintendent unless otherwise designated by the Trade Contractor in
               writing to the Construction Manager and shall attend all Safety Meetings.

1.0.13         The Trade Contractor shall not load or permit any part of the Work to be loaded so
               as to endanger its safety.

1.0.14         The Trade Contractor shall be responsible to coordinate all construction-related
               activities with Airport Operations, Airline and FAA representatives through the
               Construction Manager.

1.0.15         Any vertical lifting device whether stationary material hoist, mobile crane or other
               means, a Trade Contractor plans to use will be implemented only after prior
               coordination and approval of the Construction Manager.

1.0.16         The Trade Contractor's Site Manager (Superintendent) shall ensure that his/her
               supervisors are aware of their responsibilities. The supervisor's responsibilities are
               as follows:

                   .l   Become familiar with the requirements of all accident prevention standards
                        and safety rules pertaining to his/her job.

                   .2   Be responsible for carrying out the procedures required by accident
                        prevention, loss control standards and safe practices at the project.

                   .3   Ensure that each employee under his/her supervision has received an initial
                        safety orientation provided by Gilbane Building Company.



cscofrFcn77a:v1a/9s                                        Iv.B-l2                        Exhibit 600.1
       Subject:                Safety, Rules and Regulations                               Page 13 of 46




               .4        Explain all applicable safe practice rules and regulations to all employees
                         under his/her direct supervision and require adherence thereto.
               .5        Supervise the instruction and training of new employees either personally or
                         through delegated experienced persons until the new employee satisfactorily
                         demonstrates his/her ability to perform the work in a safe and efficient
                         manner.
               .6        Enforce safety regulations, rules and policies.
               .7        Be responsible for housekeeping in his/her area and for the use and
                         maintenance of all personal protective devices, equipment, and safeguards.
               .8        Notify his/her direct supervisor and/or the agents safety representative
                         concerning work areas where they believe protective devices are required.
                         NOTE: Such safety devices will include, but not limited to, the following:
                         machine guards, operational shields, exhaust vent hoods and systems, welding
                         shields, approved personal protective equipment, automatic stops and controls,
                         barricades, railings, etc.
               .9        Report to his/her own direct supervisor all cases of employees who, in his/her
                         opinion, are not qualified for the work to which they have been assigned or
                         who engage in unsafe practices.
               .10       Report to his/her direct supervisor all cases where employees lack sufficient
                         room or space for the performance of their work or where ventilation, heat,
                         illumination, sanitation, or other facilities are inadequate.
               .11       Attend and participate in all supervisor's safety meetings.
               .12       Conduct or arrange for "toolbox" safety meetings for all employees under
                         his/her supervision as required by project procedure.
               .13       Report immediately, all accidents in which personal injury or property damage
                         occurs.
               .14       Assist in accident investigation and submit a report promptly on required
                         forms.
               .15       Periodically analyze work methods in detail for the purpose of job
                         simplification and for the establishment of safe work methods.
               .16       Participate with the Company representative in the preparation of departmental
                         or project safe practice rules.




GBCol1'FG/1774:2/14/95                                    IV.B-13                          Exhibit 600.1
       subject:              Safety, Rules and Regulations                               Page 14 of 46



              .17       Forward to his/her supervisor all requests, suggestions, and complaints made to
                        him, together with comments he may make with regard to safe working
                        conditions and corrective measures that may be necessary or required.

              .18       Report these unsafe acts or condition to your immediate supervisor, the agents
                        safety representative and/or the site manager once you become aware of them.

              .19       The Gilbane Building Company Project Safety Manager on the project is
                        available to assist the Trade Contractor as a consultant and adviser on safety
                        matters.

              .20       Should the supervisor not uphold these obligations, he/she will be subject to
                        disciplinary action, including dismissal from T.F. Green State Airport property,
                        or those areas controlled by the Rhode Island Airport Corporation.

1.0.17        ACCOUNTABILITY - The senior Trade Contractor representative on site is
              accountable for the Trade Contractor's safety performance. As a minimum:

              .1        The Trade Contractors must provide adequate resources to comply with
                        established procedures, policy and applicable governmental requirements as
                        defined below:

                        .l     Qualified and competent personnel to manage construction and safety,
                               health and environmental activities and services.

                        .2     Trade Contractors must provide safe, reliable and approved tools and
                               equipment.

                  .2    Guidance for Trade Contractor's internal programs are defined by this
                        program. Trade Contractors may establish internal requirements that vary
                        from this program if they provide equivalent protection for the Construction
                        Manager, Design Engineer, Trade Contractors, . Rhode Island Airport
                        Corporation, and/or their agents, personnel, facilities, equipment and the
                        environment. Any such variances must be reviewed and approved by the
                        Gilbane Building Company.

                  .3    The Trade Contractor's mandatory Safety Health & Environmental Procedures
                        (including programs, policies, and procedures required by this program) are
                        documented in their written safety program.

                  .4    Trade Contractors shall conduct internal safety audits at least once for every
                        six months of continuous presence on site. Auditing format must be approved
                        by the Gilbane Building Company.

                  .5    Site inspections are to be conducted at least weekly. Trade Contractors will
                        document inspections on the Site Audit Checklist or approved Trade
                        Contractor's form.

GBColfFG/1774:2/14/95                                   IV.B-14                          Exhibit 600.1
[       Subject:   T_        Safety, Rules and Regulations                               Page I S of 46



               .6       Gilbane Building Company, Rhode Island Airport Corporation and/or its
                        agents) have established management systems to ensure that Trade
                        Contractors) comply with applicable Safety, Health & Environmental
                        requirements. Trade Contractors are to cooperate with Gilbane Building
                        Company, Rhode Island Airport Corporation and/or its agents) in
                        administering and complying with these systems. Trade Contractors will also
                        provide Gilbane Building Company, Rhode Island Airport Corporation and/or
                        its agents) with Safety, Health & Environmental information and performance
                        data upon request.


2.0           PRE-CONSTRUCTION MEETING
2.0.1         The Trade Contractor, before starting work at the job site, will attend a pre
              construction meeting with the Rhode Island Airport Corporation, Gilbane Building
              Company and/or its agents) to understand the project conditions and safety
              requirements. A job site tour shall be made to confirm the Trade Contractor's
              awareness of potential safety hazards. The Trade Contractor and his Subcontractors)
              shall invite representatives of labor unions who represent their anticipated work force
              to attend these tours. -Appropriate methods, equipment, devices and material shall
              be provided by the Trade Contractor to assure a safe work place. The Trade
              Contractor shall provide or develop his own project specific safety program (including
              procedures, data, & diagrams) and submit it to the Rhode Island Airport Corporation
              and/or its agents) for review & approval prior to orientation of personnel and start
              of work at the site. Such review shall not relieve the Trade Contractor of any
              responsibility for safety, nor shall such reviews be construed as limiting in any
              manner. It is the obligation of the Trade Contractor to undertake any action which
              may be necessary or required to establish and maintain safe working conditions at the
              job site. (Rev. 10/24/94)
3.0           INSTRUCTION AND TRAINING
3.0.1         Instruction and training of employees is an OSHA requirement and, as such, will be
              required on this project. Examples of such required training to be provided by Trade
              Contractor are:

               .1       Indoctrination - Newly employed, promoted and/or transferred personnel shall
                        be verbally instructed in the safety practices required by their work
                        assignments.

               .2       Work Assignments - All work assignments will include specific attention to
                        safety. "Follow-up" monitoring is required in order to prevent accidents.

               .3       Meetings - Properly conducted and recorded weekly craft tool box safety
                        meetings are required. Additionally, staff meetings will have a portion of the
                        agenda devoted to accident prevention.


GBConFG/1774:2/14/95                                    1v.13-15                         Exhibit 600.1
        Subject:   1         Safety, Rules and Regulations                               Page 16 of 46

               .4      Specific Instructions - OSHA requires that employees performing specific

                       tasks or operating specific equipment be trained in its usage.

3.0.2         Routine and regular training is one of the most beneficial and effective methods of
              improving safety on a site. The need for routine safety training is emphasized by two
              very important factors. First, the construction industry has an overall injury rate of
              11.8 per 100 employees versus the national average of 7.5 per 100' employees.
              Second, the construction industry has a transient work force. Training will help
              reduce the accident rate, but it must be continuous to reach all personnel.
3.0.3         Training of Trade Contractor personnel is the responsibility of the Trade Contractor.
              However, where a unique hazard potential exists or where the Trade Contractor is
              not capable of providing adequate training, Gilbane Building Company and/or its
              agent may elect to assist the Trade Contractor in training without assuming any of the
              Trade Contractor's contractual obligations, responsibilities or liabilities. As with
              orientation, Trade Contractor's training programs may be monitored by Gilbane
              Building Company, Rhode Island Airport Corporation and/or its agent(s).
              When evaluating or creating a safety training program, the following points should
              be reviewed:

               .1      The training shall be directed at all levels of a Trade Contractor's
                       organization, including management, supervision, and employees.

               .2      Accident records and reports shall be reviewed to determine where problem
                       areas exist. The training should be directed to those areas.

               .3      The training will be more effective if presented by Trade Contractor personnel
                       experienced in the subject matter. Also, the trainer's commitment to safety
                       will be enhanced by having a direct involvement in teaching fellow workers.

               .4      The training program shall consider specific instruction to employees changing
                       craft assignments and/or new work environments.

               .5      As with orientation, audiovisual aids can benefit the training effort. For
                       sources of audiovisual training aids, refer to OSHA 2019 publication, contract
                       training video companies or check with Company Representative for available
                       videos.




    ~ Based on Bureau of Labor Statistics for 1991.


cacorrFCn774:zn4/9s                                     lv.B-t6                          Exhibit 600.1
        Subject:           Safety, Rules and Regulations                                Page 17 of 46



3.0.4         "Tool Box" Safety Meeting - This method provides the standard program for training
              employees on safety procedures, safe practices, and safety rules and regulations.
              Regularly scheduled safety meetings will be conducted by the Trade Contractor's
              Project Manager/Superintendent, Area Superintendents and Foremen for the
              employees whom they supervise. Meeting reports and attendance records will be
              recorded by the Trade Contractor's jobsite supervisor.

               .1     Conducting and Reporting on Safety Meetings by the Trade Contractor:

                      .1     Conduct regularly scheduled safety meetings at least once a month
                             with the Area Superintendents.

                      .2     Conduct safety meetings at least once a week with supervisors.

                      .3     Conduct toolbox safety meetings at least once a week with employees
                             under his supervision.

                      .4     Maintain an attendance record of all Trade Contractor employees
                             present.

                      .5     Complete the equivalent form and submit it to the Project Safety
                             Manager's Office within 24 hours after each meeting.

                      .6      Attend meetings with the appropriate foremen and assist in conducting
                              the toolbox safety meetings.

                      .7      Record each Toolbox Safety Meeting Report as received.

                      .8      File all toolbox meeting reports and summaries so that they are
                              available for review at any time during project operations or for a
                              period of five years following termination of the project.


4.0            RECORD KEEPING
4.0.1          It is the Trade Contractor's responsibility to maintain all records required by OSHA,
               Worker's Compensation Insurance or similar regulations. This includes the
               maintenance of an accident log (Form 200), annual summary (OSHA Form loi or ire
               equivalent) and the posting of all prescribed posters.
4.0.2          A log of safety activities, accident investigations, employee instruction, training,
               "tool box" meetings, etc., shall be maintained on job site and copies shall be
               promptly provided to Gilbane Building Company, Rhode Island Airport Corporation
               and/or its agents) upon request.




cacorrFCn77azna/9s                                    Iv.B-17                           Exhibit 600.1
                  Subject:   F         Safety, Rules and Regulations             -T                 Page 18 of 46




          5.0            FIRE PREVENTION
          5.0.1          Trade Contractor shall be responsible for fire protection in its work and operational
                         areas, including offices, tool rooms, and storage areas twenty four (24) hours per
                         day, seven days per week through the duration of this Contract. Approved fire
                         fighting equipment fm adequate quantities) must be provided by the Trade Contractor and
                         its employees will be trained in the usage of such equipment.
          5.0.2          Good housekeeping practices designed to prevent fires and injuries around
                         construction projects are compelled to be followed:

                             .l   All electrical wiring, temporary and permanent, must meet N.E.C, NFPA and
                                  OSHA, regulations.

                             .2   No combustible material shall be stored outdoors within 10 feet of a building
                                  or structure.

                             .3   Only approved metal containers, properly labelled as to their contents, are to
                                  be used for handling and/or storage of flammable materials in quantity.

                             .4   Combustible scrap and debris shall be removed from indoor areas daily and
                                  at regular intervals from the site.

~,„,,~'   5.0.3          Where flame cutting torches, blow torches or welding tools are required to be used
                         within an existing building, their use shall be as approved by the Construction
                         Manager at the site. When welding tools or torches of any type are in use, the Trade
                         Contractor shall have available in the immediate vicinity of the work a fire
                         extinguisher of the C02 type. The fire extinguisher shall be provided and maintained
                         by the Trade Contractor.
          5.0.4          Shielding or similar precautions will be taken adjacent to welding operations.
          6.0            THIRD PARTY SAFETY INSPECTIONS
          6.0.1          In addition to visits and safety inspections by its own corporate or insurance
                         representatives, Trade Contractor is advised that the Project may be inspected from
                         time to time by authorized third parties. Among others so authorized are
                         representatives of Rhode Island Airport Corporation and/or its agent, insurance
                         companies and OSHA. Upon their proper identification, they are entitled to access
                         and courteous consideration. Gilbane Building Company, Rhode Island Airport
                         Corporation and/or its agents) are to be made aware, upon their arrival, but in any
                         case as soon as possible, of the purpose and results of such visits which relate to
                         safety.




          cBCorrFCn77a:znaws                                           lv.s-18                      Exhibit 600.1
11      Subject:   I         Safety, Rules and Regulations        I                        Page 19 of 46   ,I
7.0           CONSTRUCTION EMERGENCY ACTION PLAN
7.0.1         Gilbane Building Company will provide to Trade Contractor a Construction
              Emergency Action Plan for evacuation of a work area in the event of a natural
              disaster and/or project emergency. Trade Contractor will be responsible for advising
              its employees of the applicable emergency signals (alarm, horn, siren, etc.) and
              primary evacuation route from their work area.
7.1           SECURITY
7.1.1         The Construction Manager will establish and maintain Site Security in conjunction
              with the Rhode Island Airport Corporation, T.F. Green State Airport and F.A.A.
              Regulations.
7.1.2         All areas, other than construction areas and access paths, are Off Limits.
              Construction workers are NOT permitted inside existing buildings unless authorized
              for work.
7.1.3         All visitors) must report to the Gilbane Office, sign-in the Visitor's Log, and obtain
              the necessary visitor's pass/badge.
7.1.4         All personal vehicles shall be parked off site.
7.1.5         Material passes, obtained through the Construction Manager, shall be issued for any
              material, equipment or tools leaving the jobsite.
7.1.6         Harassment of Airport Security Personnel shall be grounds for denied access to the
              jobsite.
7.1.7         All stored material(s), tools) and equipment shall be marked with the Trade
              Contractor's name and shall be in a secure/protected location.
7.1.8         Compliance with T.F. Green Airport Rules, Regulations, and F.A.A. Directives will
              also be monitored by Airport personnel. Failure to comply will result in legal action,
              fines, and/or other considerations levied against the Trade Contractor. In the event
              an action or absence of action by the Trade Contractor with regard to the above leads
              to any damages against the public, airlines, airport, etc., the Trade Contractor shall
              be liable for all costs involved.
7.1.9         A Trade Contractor's employees unauthorized access to a secured area or harassment
              of airport/airline personnel will be considered grounds for immediate dismissal from
              the project site. In the event the employee is a trade craft person, refer to the Project
              Labor Agreement for applicable dismissal procedures.




GBCo/rFG/1774:2/14/95                                   IV.B-19                            Exhibit 600.1
        Subject:            Safety, Rules and Regulations                               Page 20 of 46



7.2           TRAFFIC CONTROL
7.2.1         The Construction Manager will provide Airport trained airside security and traffic
              control personnel for construction equipment and material deliveries to construction
              sites within the Airport Operations Area. Such deliveries shall be coordinated
              through the Construction Manager as required.
7.3           ENTRANCE ROAD
7.3.1         There will be one primary vehicle entrance to the project from Airport Road. Other
              entrances may be activated for specific construction operations.
7.3.2         The gate entrance will be used for the deliveries of all construction materials and
              equipment.
7.3.3         The Contract Documents will designate airport property to be used for construction
              parking.


7.4            GUIDANCE FOR ACCESS TO THE SITE & WORKING INSIDE A.O.A.

7.4.1          Visitors to the site will be required to register at the Construction Manager's field
               office upon arrival. Visitors are to be accompanied by their host Trade Contractor
               at all times.
7.4.2          Work Vehicles - No vehicles will be permitted to operate within the A.O.A. without
               traffic control and/or airport provided escorts present at all times. Trade Contractor
               work vehicles, vans, pickup trucks, etc., to be used on the airfield must be insured
               per contract document requirements, will be registered with the Construction
               Manager. The Trade Contractor shall provide required vehicle/equipment
               identification/markings, lighting required for the performance of their work in
               accordance with the Airport Certification Manual (A.C.M.). No workman will ride
               in back of open trucks. Rhode Island Airport Corporation will provide Trade
               Contractors with restricted information on regulations for specific vehicle/equipment
               markings/lighting required. Questions concerning access to and exit from the site
               will be referred to the Construction Manager's Project Superintendent.
7.4.3          Personnel - Workman within the A.O.A. will be shuttled to and from their
               designated work areas by the Trade Contractor, accompanied by airport provided
               escort vehicles. Work crews on the airfield will be required to have traffic control
               and/or airport provided escorts) present at all times.




cscorrFan77a:m4/9s                                     tv.s-2o                          Exhibit 600.1
        Subject:             Safety, Rules and Regulations                                  Page 21 of 46



8.0           PROJECT SAFETY AND HEALTH RULES
8.0.1         All personnel on this project, including the employees of Trade Contractor, will be
              required to comply with these rules. Trade Contractor shall ensure and indicate that
              all its employees have read the following rules and understood its contents. The
              employee must sign a declaration which shall then be retained by Trade Contractor
              with the employee's personnel file. In addition, Trade Contractor shall comply with
              the following:
8.1           CLOTHING REQUIREMENTS
8.1.1         Long or short sleeve shirts shall be worn at all times. All shirts shall be tucked in
              trousers at all times. All shirts shall be hemmed at neck, sleeve and tail.
8.1.2         Long pants are required.
8.1.3         Sandals, sneakers, tennis shoes or any other street type shoe or look-a-like will not
              be permitted for trades craft people. A well constructed boot/shoe that provides ankle
              protection with a hard flexible sole shall be worn. Exposure dictates whether or not
              a protective toe guard will be required.
8.1.4         Loose fitting clothes or jewelry shall not be worn around moving machinery, grinding
              operations, welding, etc.
8.1.5         Hair which could come in contact with, or be caught in machinery, shall be protected
              by a hard hat or hair net, as appropriate.
8.2           PERSONAL PROTECTIVE EQUIPMENT
8.2.1         Approved hard hats meeting specifications contained in American National
              Standards Institute (ANSI), 289.1-1981 and/or 289.2-1971 are required.
8.2.2         Appropriate eye protection (ANSI Z87) with side shields are required to be worn in
              a normal manner in construction areas at all times.

               .l       Other - Approved eye and face protection is required as follows: Goggles,
                        welding hoods and shields, and face shields will be required to be properly
                        worn at all times when in the area of operations, such as when welding,
                        burning, grinding, chipping, chemical handling, corrosive liquids or molten
                        materials, drilling, sawing, driving nails, power actuated tools, concrete
                        pouring, tampers and gasoline fueled hand operated equipment (i.e. chain
                        saws). This section will also apply to those employees of Trade Contractor
                        who are assisting any worker as an apprentice or helper. Prescription glasses
                        must be approved safety glasses, approved safety glasses and frames, or

GBCo/TFG/1774:2/14/95                                   IV.B-21                             Exhibit 600.1
        Subject:   I        Safety, Rules and Regulations                                   Page 22 of 46



                       approved eye protection. Photo Grey lenses will not be allowed. Contact
                       lenses will not be allowed in construction areas.

8.2.3         OSHA approved hearing and respiratory equipment shall be worn when required. The
              selection, fitting and maintenance requirements of OSHA shall be met by the Trade
              Contractor.
8.2.4         Class III full body safety harnesses are the only personal fall protection device
              approved for use on this project.

               .1      Safety Harness shall be worn and used by all employees when working six
                       (6') feet or more above the ground/floor or whenever working in a precarious
                       position.

               .2      All lanyards are to be as short as possible, but in no event longer than SIX
                       FEET (6'-0"). It is recommended that devices be used in conjunction with
                       the lanyards.

               .3      Safety Harness shall also be worn and attached to the tie-off rail when
                       working out of extendible and articulating boom platforms and to vertical drop
                       lines when working from suspended scaffolding.

               .4      All anchorages for personal fall protection systems shall be capable of
                       resisting a force of 5,400 lbs. for each individual tied off to that anchorage.

                       .1      Vertical safety lines shall only be used by one individual at a time.

8.2.5          Seat belts shall be worn by all employees operating motor vehicles and any equipment
               with rollover protection structures during performance of the work.
8.2.6          Safety nets shall be provided when work places are more than twenty-five (25') feet
               above the ground where the use of other fall protection devices are impractical. This
               will apply to steel erection as well as other activities.
8.3            SIGNS. SIGNALS. BARRICADES & LIGHTS
8.3.1          Signs, signals, and barricades shall be visible at all times where a hazard exists.
8.3.2          All streets, roads, highways and other public thoroughfares which are closed to traffic
               shall be protected by effective barricades on which shall be placed acceptable and
               highly visible reflective warning signs and flashing lights (when required). Barricades
               shall be located at the nearest intersecting public highway or street on each side of the
               blocked section.
8.3.3          All open trenches and other excavations shall be provided with suitable barriers, signs
               and lights to the extent that adequate protection is provided to the public.


cBCorrFCn774:2n4/9s                                    Iv.B-22                             Exhibit 600.1
        Subject:            Safety, Rules and Regulations                                 Page 23 of 46



              Obstructions, such as material piles and equipment, shall be provided with similar
              warning signs and lights.

8.3.4          All barricades, and obstructions shall be illuminated by means of warning lights from
               1 hour before sunset to 1 hour after sunrise. Materials stored upon or alongside public
               streets and highways shall be so placed, and the work at all times shall be so
               conducted, as to cause the minimum obstruction and inconvenience to the traveling
               public.
8.3.5          All barricades, signs, lights, and other protective devices shall be installed and
               maintained in conformity with applicable statutory requirements and, where within
               airports and highway right-of-way, as required by the authority having jurisdiction
               thereof.
8.3.6          When any work is performed at night or where daylight is shut off or obscured, Trade
               Contractor shall, at its expense, provide artificial light sufficient to permit work to be
               carried on efficiently, satisfactory and safely, and to permit thorough inspection.
               During such time periods the access to the place of work shall also be clearly
               illuminated. All wiring for electric light and power shall be installed and maintained
               in accordance with Federal and State codes, securely fastened in place at all points,
               and shall be kept as far away as possible from telephone wires, signal wires, and wires
               for firing blasts.
8.3.7          At no time shall the Trade Contractor remove, alter or render ineffective any
               barricades, railings or cover on the project without the written permission of the
               Construction Manager. The Trade Contractor shall restore all safety measures so
               disturbed to required standards as directed by the Construction Manager. Where these
               safety devices are to be turned over to others upon completion of the work the devices
               shall be repaired or replaced so that they meet the required standards prior to turnover.
8.3.8          Signs, signals and barricades shall be removed when the hazard no longer exists.
8.3.9          Trade Contractor's employees working in an area of potential traffic hazard shall wear
               approved (OSHA/ANSI/RIDOT) reflective type vests.
8.3.10         The Trade Contractor shall insure that all signs, signals, markings and devices placed
               on, over or adjacent to a street or highway be installed and maintained in accordance
               with the requirements of the Federal Highway Administration Manual of Uniform
               Traffic Control Devices, including all latest revisions.
8.4            RIGGING EQUIPMENT
8.4.1          All rigging equipment shall be free from defects, in good operating condition and
               maintained in a safe manner.




cBCo/'rFcn77a:ma/9s                                    Iv.B-23                            Exhibit 600.1
        Subject:   I       Safety, Rules and Regulations                                  Page 24 of 46



8.4.2         Rigging equipment shall be inspected by a designated, competent employee of Trade
              Contractor prior to initial use on the job site work and monthly thereafter to ensure
              that it is safe. Records shall be kept on job site of each inspection by Trade Contractor
              and shall be made available to Rhode Island Airport Corporation and/ or its agent
              upon request.
8.4.3         Trade Contractor's damaged rigging equipment shall be immediately removed from
              service by Trade Contractor.
8.5           HAND & POWER TOOLS
8.5.1         All hand and power tools, whether furnished by Trade Contractor or by Trade
              Contractor's employee, shall be maintained in a safe condition.
8.5.2         Trade Contractors shall not issue nor permit the use of unsafe hand or power tools.
8.5.3         All electrical cords, tools, and similar equipment must be maintained in good
              condition. All moving parts of machinery, such belts, pulleys, gears, etc., must be
              guarded if the parts are exposed to contact by the operator.
8.5.4         Electrical power/hand tools must have double insulated frames or the frames
              grounded, proper assured equipment grounding inspections, Ground Fault Circuit
              Interrupter protection, a constant pressure switch and must not be raised or lowered
              by the cord. Power tools must have the proper guards attached and must be used as
              intended. Portable welding machines having electric receptacles should be grounded.
8.5.5         Pneumatic power tools shall be secured to the hose or whip by some positive means.
8.5.6         Only properly trained Trade Contractor's employees shall operate powder actuated
              tools. Certification records, employee certification cards, or equivalent certification
              documentation shall be maintained by Trade Contractor on each of its employees
              using powder actuated tools during performance of their work.
8.5.7         All grinding machines shall conform to OSHA and ANSI requirements. All disks
              (blades) will be guarded and have an RPM rating equal to or greater than the tool.
8.5.8         Cords, leads and hoses shall be kept at least seven feet (7'-0") off the ground or
              whatever height is necessary to be protected from traffic and creating tripping hazards.
8.5.9         Personal Protective Equipment must be worn by operators to guard against the threat
              of falling, flying, abrasive, splashing objects, harmful dusts, mists, fumes, vapors or
              gases.
8.5.10        Pneumatic tools must have positive locks on hoses and attachments. Nailers, staplers,
              and comparable other air-driven equipment will have a device to prevent operations
              unless in contact with the surface if the air pressure is over 100 psi. Compressed air


cscorrFCim74:m4/9s                                    IV.B-24                             Exhibit 600.1
               I
              11
         Subject:
         of 46
                                                                                Safety, Rules and RegulationsPage 25

               will not be used for cleaning if the pressure is over 30 psi when dead ended. Hoses
               shall not be used to raise or lower tools.
8.5.11          Each Trade Contractor shall, in a readily visible manner, identify all of his tools,
               equipment and similar materials, either by paint color or label.
8.6            COMPRESSED GAS CYLINDERS
8.6.1          Compressed gas cylinders shall be secured in an upright position at all times by means
              of chain or wire. Location of cylinder storage areas must be approved by Gilbane
              Building Company, Rhode Island Airport Corporation and/or its agent(s).
8.6.2         When transporting, moving and storing cylinders, valve protection caps shall be in
               place and secured.
8.6.3         Cylinders shall not be hoisted by magnets or choker slings. Valve protection caps shall
              not be used for hoisting cylinders.
8.6.4         Cylinders shall be kept away from sparks, hot slag and flames, or be adequately
              protected.
8.6.5         Cylinders shall not be placed where they can become part of an electrical circuit.
8.6.6         Cylinders shall be labelled as to the nature of their contents.
8.6.7        Oxygen cylinders in storage shall be separated from fuel gas cylinders or combustible
              materials a minimum of twenty feet (20'-0") or by a non-combustible barrier at least
              five feet high having a fire resistant rating of at least one-half hour and empty
              cylinders shall be separated as above from full cylinders and stored with like
              cylinders.
8.6.8         "No Smoking" signs shall be posted at storage areas and signs shall clearly indicate
               contents of cylinders.
8.6.9          Anti-Flash back arresters shall be installed on all oxygen and acetylene assemblies, on
               the regulators, when set-up for use.
8.6.10         At the end of each work day, or when work is suspended for a substantial period of
               time, compressed gas cylinder valves will be closed, regulators removed and properly
               stored. Cylinders will remain. within their carrier, provided it is intended for the
               purpose, or otherwise secured by wire or chain in an upright position with valve
               protection caps screwed securely in place.




GBCo/fFG/17742/14/95                    IV.13-25                                Exhibit 600.1
         Subject:   I                                Safety, Rules and Regulations (              Page 26 of 46 ``

8.7           SCAFFOLDS
8.7.1         Footings or anchorage for any scaffold shall be sound, rigid and capable of carrying
              the maximum intended load without settling or displacement.
8.7.2         No unstable objects such as pieces of lumber, bricks, scrap blocks, etc. shall be used
              to support scaffolds or planks.
8.7.3         Any part of a scaffold weakened or damaged shall be repaired or replaced
              immediately.
8.7.4         All scaffold planking shall be free of knots and cracks (Class A Scaffold Lumber) and
              shall completely cover the work platform.
8.7.5         Scaffold planks shall be laid tight, cleated at both ends or overlapped a minimum of
               twelve inches (12") and nailed or bolted to prevent movement. Overlaps to occur
               directly above scaffold supports. Only planks color coded with green ends are
               permissible for use as scaffold planks.
8.7.6          Safe access shall be provided to the scaffold platform. Specifically, a ladder with a
               safe means of access to the platform from the ladder.
8.7.7          Scaffolds shall be equipped with a top rail made of lumber not less than 2 x 4 inches
              (or equivalent strength), 42 inches high, a 21 inch high midrail, made of lumber not
               less than 1 x 6 inches (or equivalent strength); and toeboards shall be installed on all
              open sides and ends of scaffold platforms six feet (6'-0") or more above the ground
              floor.
8.7.8         Scaffolding not adaptable to guardrails shall require employees to use safety harnesses
              with the lanyard attached to a secure substantial object.
8.7.9          Mobile scaffold casters shall be secured and locked prior to mounting.
8.7.10         NO personnel or loose material shall be on mobile scaffold when it is being relocated.
8.7.11         Trade Contractor's employees working swing stages, boatswain chair, floats,
               suspended scaffolds and needle beam scaffolds (etc), shall wear safety harnesses with
               lanyards attached to an independent lifeline.
8.7.12          A proper scaffold inspection and tagging system shall be maintained.
8.8            JOBSITE TRANSPORTATION RULES
8.8.1          Drivers of motor vehicles shall have a valid state drivers license (CDL when
               applicable) and be instructed to exercise judgment as well as observe posted speed


cBCo/'rFci»7a:zna/9s                  IV.B-26                                     Exhibit 600.1
         Subject:   I                                Safety, Rules and Regulations   I               Page 27 of 46   ,1
               limits. Maximum site speed limit is ten (10) miles per hour. However much slower
               speeds are necessary in congested areas.
8.8.2         All Trade Contractor's means of ingress and egress shall be adequately marked and
              kept clear of stored material, debris and equipment.
8.8.3         Pedestrians and bicycles have right-of-way over motorized traffic.
8.8.4         Use your horn for safety at blind corners, when passing, etc.
8.8.5          Established hand signals or turn signals are to be used.
8.8.6          Reckless driving or other non-observance of these instructions will be cause for
              withdrawal of driving privileges on the project.
8.8.7          Any All Terrain Vehicles used on the jobsite shall be of a four (4) wheeled type, not
              of a three (3) wheeled type.
8.8.8         All vehicles permitted access to the A.O.A. will display an appropriate vehicle
              identification badge from the rear view mirror or other conspicuous location at all
              times while on the project.
8.8.9         Refer to Article 7 for other special requirements.
8.8.10        Riding in the rear, side or any manner which is not intended for passenger transport
              of any vehicle or equipment is prohibited.
8.9           CRANES & DERRICKS
8.9.1          All cranes and derricks shall be in conformance with ANSI B30.5 certified as being
              in safe operating condition by Trade Contractor prior to using the crane or derrick on
              job site on a daily basis. This certification shall be maintained by Trade Contractor
              and made available to Gilbane Building Company upon request.
8.9.2          All crane operators shall be properly licensed to operate in the state of Rhode Island.
              Certification records shall be maintained on job site by Trade Contractor and made
              available to Gilbane Building Company upon request.
8.9.3          A thorough, annual inspection of hoisting machinery (cranes and derricks) shall be
              made by a Government or private agency recognized by the U.S. Department of
               Labor. The Trade Contractor will post the inspection certificate in the cab or
              operator's station of the hoisting machinery (cranes and derricks) and provide Gilbane
              Building Company a copy of the inspection certificate results upon request.




 cBCorrFCn774:ma/9s                   IV.B-27                                        Exhibit 600.1
11        Subject: (                           Safety, Rules and Regulations   I               Page 28 of 46   I
8.9.4    Cranes and derricks shall be inspected prior to use and at monthly intervals. Records
         shall be maintained on job site of these inspections by Trade Contractor and copies
         shall be made available to Gilbane Building Company upon request.
8.9.5    The swing radius of cranes shall be barricaded for protection of pinch points. The
          load line will be secured when work has been stopped or at end of day/shift.
8.9.6     Hand signals prescribed by ANSI B 30.5 shall be posted at an operator's station.
8.9.7     Manufacturer's specification shall be observed by Trade Contractor.
8.9.8     Cranes, derricks, backhoes and other hoisting machinery, including the load, shall not
          be operated where any of the equipment or load will come within fifteen feet (15'-0")
          of electrical distribution or transmission lines, rated at 50 KV or below, which have
          not been de-energized AND visibly grounded at the point of work without a "close
          proximity work permit" approved by site management. Cranes having more than 200
         feet of boom in the air or that will be erected/operated within the Part 77 clear zone
         must contact Federal Aviation Administration (FAA), 30 days prior to assemble for
         necessary boom lighting instruction.
8.9.9    Trade Contractor's employees shall not ride the headache ball, hook, or load being
         handled by the crane.
8.9.10   Equipment shall not be lubricated while in use.
8.9.11   Rated load capabilities, recommended operating speeds, special hazard warning,
         specific hand signal diagram and special instructions shall be visible to the operator
         while he/she is at the control station.
8.9.12   Trade Contractor's employees shall not be allowed to work under the load of cranes.
         Tag lines shall be used on all loads. Special caution should be used in concrete
         bucket operations.
8.9.13   Construction equipment and vehicles will be inspected by the Trade Contractors with
         regularly scheduled maintenance and repair performed when required to keep the units
         in safe operating condition.
8.10     TOWER CRANE SPECIFICS
8.10.1   A complete and documented annual inspection will be performed before the machine
         arrives on site and then an annual inspection thereafter.
8.10.2   The complete annual inspection of all structural crane parts including NDE test of
         welded joints by a competent person qualified in accordance with OSHA 29 CFR Part
         1926.32 (f), will be furnished by the crane supplier prior to the erection of the crane.


cBConTGn77a:2nar9s               Iv.B-2s                                       Exhibit 600.1
       Subject:   I     Safety, Rules and Regulations             I                   Page 29 of 46
             A copy of this inspection and NDE test results shall be matched on site. The
             inspection will also be certified by a registered engineer.
8.10.3       Cranes shall have flags or other indicators on the jib identifying the working load
              radius to the operator. If the crane jib is intended to extend more than 200 feet
              vertical in the air or that will be erected/operated within the Part 77 clear zone, the
              Federal Aviation Administration (FAA) must be contacted 30 days prior for necessary
              instruction on jib lighting configuration.
8.10.4       Tower cranes shall have limiting devices to control: 1) Trolley travel at both ends of
              the jib; 2) anti-two blocking; 3) operating radius in accordance with lifted load; 4)
              pressures in hydraulic or pneumatic circuits and; 5) crane travel at both ends of the
              runway tracks. Load limiting devices, and acceleration and deceleration limiters, when
              provided, shall be installed in enclosures that can be locked or sealed to inhibit
              unauthorized tampering.
8.10.5       The operator shall be trained, experienced and qualified for the operation of that
              specific make and model of tower crane. Operator experience documentation shall
              be provided by the utilizing Trade Contractor even if he is using a Trade
              Subcontractor on site.
8.10.6       The manufacturer's operator manual shall be kept with the crane while it is on site.
8.10.7         A wind velocity indicating device shall be mounted at or near the top of the crane.
              A velocity readout shall be provided at the operators station in the cab, and a visible
              or audible alarm shall be triggered in the cab and at remote control stations when the
              preset wind velocity has been exceeded.

8.10.8        Regular inspections and maintenance of the cranes shall be conducted and performed
              in accordance with the manufacturers specifications and ANSI Standards.


8.11          EQUIPMENT & MOTOR VEHICLES

8.11.1        All equipment will be inspected daily before use by Trade Contractor's operator.
              Formal inspections shall also be made by Trade Contractor at 30 day intervals with
              proper documentation maintained at the job site by Trade Contractor and copies shall
              be made available to Gilbane Building Company, Rhode Island Airport Corporation
              and/or its agents) upon request.

8.11.2        Defective equipment shall be repaired or removed from service immediately.

8.11.3        All rubber-tired, self-propelled scrapers, rubber-tired front-end loaders, rubber-tired
              dozers, wheeled-type agricultural and industrial tractors, crawler type loaders and
              motor graders shall be equipped with roll-over protective structures and seat belts as
              per manufacture's specifications and OSHA Requirements.




cBCorrFCn774:ma/9s                                      Iv.B-29                       Exhibit 600.1
        I
        Subject:                                                                    Safety, Rules and Regulations Page 30 of 46



8.11.4         All Trade Contractor's operators of construction equipment shall be properly licensed
               and certified by a competent person. Copies of the certifications shall be maintained
               on job site by Trade Contractor and made available to Gilbane Building Company,
               Rhode Island Airport Corporation and/or its agents) upon request.

8.11.5          All equipment with an obstructed view to the rear shall have a reverse signal alarm
               audible above the surrounding noise level.

8.11.6          All cracked and broken glass shall be replaced before bringing vehicles on the job site.
                If glass is damaged on the job site and if damage is severe enough to cause a potential
                safety problem, the equipment shall be stopped until such damage has been repaired.

8.11.7          Vehicles used to transport employees shall have seats firmly secured and adequate for
               the number of employees to be carried and all passengers shall be properly seated.
               Standing/kneeling on the back of moving vehicles is prohibited.

8.11.8          Locations for storage of all fuels, lubricants, starting fluids, etc., shall be reviewed by
                Gilbane Building Company, Rhode Island Airport Corporation and/or its agents) prior
                to use by Trade Contractor for storage.


8.12            ELECTRICAL TEMPORARY POWER & GFCI

8.12.1           All electrical work, installation and wire capacities shall be in accordance with the
                 pertinent provisions of the National Electrical Code, ANSI and OSHA Standards.
                 .1           All 120 volt, single phase, 15 & 20 amp temporary power circuits (with the
                              exception of temporary lighting) shall have ground fault circuit interrupters
                               installed. In addition all tools, cords and power sets shall have an assured
                               equipment inspection program maintained on quarterly basis.
                .2            The color codes used on this project are:

                               January, February, March                                  -    White
                               April, May, June                                          -    Green
                               July, August, September                                   -    Red
                               October, November, December -                                  Orange
                                   (The cycle of colors is repeated for the next year)



8.12.2             Trade Contractor shall determine before operations start if there is any energized
                   equipment or electrical circuit in the work area which might have risk to the worker.
                   Equipment and conductors that will be de-energized shall be identified to the Gilbane
                   Building Company, Rhode Island Airport Corporation and/or its agents) who will
                   arrange to de-energize the equipment under the T.F. Green State Airport Project
                   Lockout and Tagging procedure/system.




GBCo/TFG/1771:2/14/95                  Iv.s-30                                               Exhibit 600.1
        Subject:                                                     Safety, Rules and Regulations Page 31 of
        46


8.12.3       All non-current carrying parts of electrical equipment shall be grounded or have an
             approved double-insulated setup. Grounded circuits shall have enough capability
to carry all currents likely to be imposed on it.
             carry all currents likely to be imposed on it.
8.12.4      Extension cords used with portable tools shall be of a heavy duty 3-wire type. All
            necessary open wiring shall be made inaccessible to unauthorized employees or
            visitors. Lighting on barricades, fences, or sidewalk coverings shall be encased in
            metal raceway. Temporary lighting shall have guards to prevent accidental contact with
            the bulb except where the bulb is deeply recessed in the reflector. Temporary lights
            shall not be suspended by the cord unless the fixture was specifically designed in that
            manner, as with trouble lights. Portable electric lighting used in moist or other
            hazardous locations such as drums, tanks, vessels, bins, bunkers, etc., shall be operated
            at a maximum of 12 volts (non-explosive).

8.12.5         Extension cords will not be fastened with staples, hung from nails, or suspended by
               non-insulated wire. Damaged electrical cords will not be used, but rather immediately
               removed from service until repaired.
8.12.6         All electrical equipment and wiring in hazardous locations shall conform with the
               National Electrical Code standards. The frames of all cutting, welding (arc, heli-arc,
               gas-plasma-arc) machines shall be grounded.
8.12.7         Trade Contractor shall use the project LockoutJTagout procedure and strictly adhere
               to the use of this requirement. Gilbane Building Company, Rhode Island Airport
               Corporation and/or its agents) will monitor adherence to the procedure on a regular
               basis.



8.12.8          All temporary power panels shall have covers installed at all times. All open or
                exposed breaker spaces shall be adequately covered, and labeled.
8.12.9          Metal rules or tapes lines containing metal shall not be used around electrical
                conductors or equipment.
8.12.10         All temporary wiring shall be effectively grounded in accordance with the National
                Electrical Code (Articles 305 and 310). All wiring used for temporary lighting shall be
                non-metallic sheathed cable (NM) or the equivalent as approved by Gilbane Building
                Company, Rhode Island Airport Corporation and/or its agent(s).




8.13            LADDERS

8.13.1          The use of ladders with broken or missing rungs or steps, broken or split rails or other
                defective construction is prohibited.

                 Ladders shall extend no less than 36 inches above landing and be secured to prevent
                displacement.


GBCoIrFG/1774.2/14/95                IV.B-31                                Exhibit 600.1
        Subject:                                                                     Safety, Rules and Regulations Page 32 of
        46

       8.13.3             Portable ladders must be equipped with safety shoes.

       8.13.4            Wooden ladders shall not be painted.

       8.13.5             Metal or conductive ladders shall not be used on the job site.                                        ',

        8.13.6       Job made ladders are acceptable when made to OSHA specifications. These ladders
                     will only be used to gain access to upper floors when no other means is available
               and in trench and excavations.
        8.13.7       When there is a break in elevation of nineteen (19") inches or more, ladders or ramps
                     are required for access or
               egress.
        8.13.8       When working off a ladder and you're feet are six (6') feet or more above the
                     ground/floor either be tied off using a safety harness, utilize a second person to
              hold the ladder, or utilize a different means of gaining access (i.e., scissor lift, scaffold,
              etc.).

        8.14             FLOOR & WALL OPENINGS & STAIRWAYS

        8.14.1           Floor and wall openings shall be guarded by either a standard guardrail, or its equivalent, or

        adequately covered.


          8.14.2      Guardrail shall be of sufficient strength to support 200 pounds of pressure applied in
                       any direction with a maximum deflection of 3
                 inches.

          8.14.3            Covers for floor openings shall be adequately secured to prevent accidental
                         displacement and have "Danger - Floor Hole" signs attached identifying the hazard.
          8.14.4          Every flight of stairs having four or more risers shall be equipped with standard stair
                          railings. Stairs are not to be used until risers, landings and railings are securely
                           installed. Treads will be poured as soon as possible where poured treads apply.

          8.14.5            Debris and other loose materials shall not be allowed to accumulate in stairwells.

          8.15              EXCAVATIONS & TRENCHING

          8.15.1          The Trade Contractor must designate a competent person trained in soil classification
                       and the recognition of trenching and excavation hazards. This person must be
                 on-site when excavating or trenching is being done.

          8.15.2          Appropriate documentation to meet the OSHA trenching and excavation standards is
                          to be maintained on
                 site.




GBCo/t'FG/17742/14/95                        Iv.B-32                                        Exhibit 600.1
Subject: -    Safety, Rules and Regulations ~                              Page 33 of 46 `~
8.15.3       Prior to opening any excavation or trench an excavation permit is required. Trade
             Contractor shall notify necessary personnel to determine whether under-ground
             installations; i.e. sewer, telephone, fuel, electric lines, etc., may be encountered and
             where they are located. Excavation permits shall be required.
8.15.4       Excavations and trenches shall be inspected daily or at more frequent intervals as
             conditions require, by a competent person daily and after every rainfall to insure the
             trench is safe.
8.15.5       Side walls of all excavations/trenches five (5') feet or more in height shall be sloped
             to 1-I/2 to I (34°) unless soil is analyzed by a competent person allowing a greater
             slope angle, or otherwise shall be adequately shored.
8.15.6       Ladders or steps shall be provided in all trenches 4 feet or more in depth. Ladders
             shall be located to require no more than 25 feet of lateral travel before having access
             to an acceptable ladders) shall extend 3 feet above the top of the trench bank.
8.15.7       Excavated material shall be stored at least 3 feet from the edge of the
             excavation/trench. Excavated material shall be stored so as to prevent material from
             falling into the excavation.
8.15.8       All trenches and excavations shall be properly barricaded to prevent persons from
             falling into them.

8.15.9       All walkways or ramps crossing over excavations shall be securely fastened and
             equipped with standard guardrail.


8.16         STEEL ERECTION

8.16.1       At no time shall there be more than four floors or 48 feet of unfinished bolting or
             welding above the foundation or uppermost permanently secured floors.

8.16.2       A temporary and/or permanent floor shall be maintained within 2 stories or 25 feet,
             whichever is less, below and directly under that portion of each tier of beams on
             which any work is being performed.

 8.16.3      Planking or metal decking in temporary floors shall be of proper strength and a
             thickness to carry the working load. Decking shall be immediately secured in place
             to prevent movement.

 8.16.4      During structural steel assembly, two (2) safety railing (cable) of 5/8 inch diameter
             shall be installed approximately forty-six (46") inches high, and at the mid point,
             recessed into the interior of floor around all temporary floors.




 cecortTcn77a:v14/9s                     tv.B-33                           Exhibit 600.1
Subject:         Safety, Rules and Regulations                                Page 34 of 46
8.16.5        Tag lines shall be used to control all loads or portions thereof.

                .l     "Christmas Tree" configurations will not be allowed on structural members
                       going aloft from ground.
8.16.6        Containers (buckets or coal type bags) shall be provided for storing or carrying bolts
               or rivets. When bolts, drift pins or rivet heads are being removed, a means shall be
               provided to prevent accidental displacement. Tools shall be secured in such a manner
               to prevent accidental falling.
8.16.7        During the final placing of solid web structural members, the load shall not be
               released from the hoisting line until the members are secured with not less than two
               bolts, or equivalent, at each connection.
8.16.8        A safe means of access to the level being worked shall be maintained. Climbing and
               sliding columns or diagonals, is not considered safe and not allowed.

8.17            CONFINED AREAS OR SPACES

8.17.1          Trade Contractor shall develop an entry procedure to be used when Trade Contractor's
                employees are required to enter confined areas or spaces. Confined spaces include but
                are not limited to; storage tanks, process vessels, bins, boilers, ventilation or exhaust
                ducts, sewers, underground utility vaults, tunnels, pipelines, open-topped pits,
                basements and temporary wood framing covered with plastic.

8.17.2           All Trade Contractor employees who are required to enter confined areas or spaces
                shall be instructed as to the nature of hazards involved, necessary precautions to be
                taken and in the use of protective and emergency equipment required. Employees
                required to wear respirators shall: a) Be fit tested to include quantitative and
                qualitative tests, and; b) Pulmonary medical examination.

8.17.3          Before Trade Contractor's employees are permitted entry into any confined area or
                space, the atmosphere within the space shall be tested to determine the oxygen level
                and potential concentrations of flammable vapors, gases, toxic contaminants. Trade
                Contractor needing access to the confined area shall furnish the testing equipment and
                a person competent in the use of the testing equipment. A confined space entry
                permit is required and posted at or near the entrance to the confined space

 8.17.4         When welding, cutting or heating in confined areas or spaces, ventilation shall be
                provided. When sufficient ventilation cannot be provided without blocking the means
                of access, Trade Contractor's employees shall be protected by air line respirators and
                an employee of Trade Contractor shall be stationed outside the confined space to
                maintain communication with those working within and to aid them in an emergency.
                Stand-by employee shall be trained in emergency procedures.




 GBCo(fFG/17742/14/95                       IV.B-34                           Exhibit 600.1
Subject:         Safety, Rules and Regulations                               Page 35 of 46   I
8.17.5          Reference Form No 17, Titled 'Confined Space Entry' for further information and
                requirements.

8.18            HOUSEKEEPING

8.18.1          Each Trade Contractor shall be responsible for daily and final cleanup and continuous
                 removal of all rubbish and debris from the building and site. Trade Contractor will
                 remove all crates, cartons, and other flammable waste material and trash from the
                 work areas) at the end of each workday. Each Trade Contractor shall be responsible
                 to deposit his rubbish into the dumpsters as designated by the Construction Manager.
                 If a Trade Contractor fails to meet his obligation to clean up and remove rubbish,
                 following a 24 hour notice from the Construction Manager, the work will be done by
                 others and charged to the Trade Contractor.
8.18.2          In order to comply with applicable F.A.A. regulations and the Airport Certification
                 Manual, every Trade Contractor will be accountable for adhering to the stringent
                 traffic movement, clean-up, debris and dust control requirements for this project.
8.18.3          In the event a .condition is identified that, in the opinion of the Rhode Island Airport
                 Corporation, Gilbane Building Company and/or it agent(s), constitutes an imminent
                 peril to public and/or private property, the Construction Manager may initiate prior
                 to written notice, such action as may be necessary to alleviate the condition with all
                 costs charged to the delinquent Trade Contractor.

8.18.4          All materials brought to/from the site, including waste materials shall be secured
                during transport and stored so as not to cause any Foreign Object Damage(F.O.D.).

8.18.5          Special attention shall be given to any materials or debris which could become F.O.D.,
                 as it may cause damage to aircraft while operating/moving on the A.O.A. taxiway(s)
                 and runway(s). Any F.O.D. accidentally deposited by any Trade Contractor on
                 runways, taxiways, ramps, or aprons, shall be removed immediately. If the
                 Trade Contractor fails to remove such material/debris immediately, the
                 Construction Manager will have such material/debris cleaned-up, without prior
                 written notice, at the Trade Contractor's expense. Repeated violations will be
                 cause to suspend or terminate the responsible Trade Contractor or Trade
                 Subcontractor.

 8.18.6          Non-aircraft operational pavements shall be cleaned at the end of each day's work or
                 as otherwise directed.

 8.18.7          Each Trade Contractor shall take all measures necessary to control, at all times, the
                 dust created by his operations. Vacuuming, sweeping, water spraying and covering
                 shall be considered minimum measures both inside and outside of buildings.

 8.18.8          The Trade Contractor will deposit construction debris in dumpsters on a daily basis.
                 All dumpsters will have covers and remain covered at all times.


 GBCo/1'FG/1774:2/14/95                     IV.B-35                          Exhibit 600.1
         Subject: Safety, Rules and Regulations                           Page 36 of 46
                                                                                                    Ji




8.18.9         Dumpsters shall be provided by Gilbane Building Company for the disposal of general
               rubbish and debris.

8.18.10         Garbage and other waste shall be disposed of at frequent or more regular intervals in a
                manner approved by Gilbane Building Company, Rhode Island Airport Corporation
                and/or its agent(s).

8.18.11         Trade Contractor shall notify Gilbane Building Company, Rhode Island Airport
                Corporation and/or its agents) of any hazardous waste it will generate during
                performance of the Work. Trade Contractor has the direct responsibility of maintaining
                proper storage of these wastes while on site and will verify to Gilbane Building
                Company, Rhode Island Airport Corporation and/or its agents) in writing that the
                wastes have been disposed of in a legal manner. A copy of the haulers manifest shall be
                provided to Gilbane Building Company, Rhode Island Airport Corporation and/or its
                agent(s).

8.18.12         Trade Contractor shall not pour, bury, burn, nor in any way dispose of any rubbish,
                debris or waste of any kind on the work job site.

8.18.13         Trade Contractor shall clear all combustible debris to a solid waste disposal job site
                properly licensed under the laws of the State of Rhode Island or any surrounding
                jurisdiction. NO OPEN BURNING OF DEBRIS OR RUBBISH WILL BE
                PERMITTED ANYWHERE ON THE PROJECT SITE.

8.18.14         Materials and supplies shall be stored in locations which will not block access ways and
                arranged to permit easy cleaning of the area. In areas where equipment might drip oil or
                cause other damage to the floor surface, a protective cover of heavy gauge, flame
                resistant, oil proof sheeting shall be provided between the equipment and the floor
                surface sheeting so that no oil or grease contacts the concrete. This requirement is
                applicable to both finished and unfinished floors.

8.18.15         All hoses, cables, extension cords and similar materials shall be located, arranged and
                grouped so that they will not block any access way and will permit easy cleaning and
                maintenance.


8.19           GENERAL

8.19.1      Gilbane Building Company, Rhode Island Airport Corporation and/or its agents)
            reserves the right to regulate smoking, open fires, carrying matches, and welding
            permits when and where deemed necessary in the interest of safety. Trade Contractor
            shall be responsible for and so enforce Trade Contractor's personnel, the personnel of
            all Trade-Subcontractor's and visitors to comply with the regulations and restrictions
            as directed. The smoking, open fires and similar regulations may vary during the
            progress of construction, or during the testing, or initial operation of any portion of
            the plant.
csconTcnna:ma/9s                  IV.B-36                                 Exhibit 600.1
II     Subject:           Safety, Rules and Regulations            I                      Page 37 of 46   I`
8.19.2       Hot work permits are required in all existing buildings owned, leased or occupied by
             Rhode Island Airport Corporation employees. A adequate portable fire extinguisher
             shall be in the immediate area.
8.19.3       Smoking is prohibited within all buildings, trailers and Rhode Island Airport
             Corporation property, except in those areas explicitly identified/posted as "Designated
             Smoking Area(s)."

8.19.4       No firearms are allowed on the job site.

8.19.5       Photographic equipment inside Airport property is strictly forbidden without specific
             approval of Gilbane Building Company, Rhode Island Airport Corporation and/or its
             agent(s).
8.19.6       Written evidence that all of the requirements of this section are being complied with
             shall be maintained by Trade Contractor on the job site and made available to Gilbane
             Building Company, Rhode Island Airport Corporation and/or its agents) upon request.
8.19.7       Facilities-The location of lunch areas and portable toilet facilities will be designated
             by the Construction Manager. The use of existing facilities, hold rooms, and
             passenger gate areas by workmen for lunch breaks is absolutely prohibited. The
             sanitary regulations in current safety standards will apply to the project as a whole.
             Use of existing airport toilet rooms is prohibited.
8.19.8       Potable Water - Each Trade Contractor shall provide their employee(s), potable water
             at the work site from a source provided/identified by the Construction Manager.
8.19.9       Diseases - Access to the site may be denied to personnel carrying or suffering from
             contagious disease(s).
8.19.10      The Trade Contractor agrees to notify the Construction Manager's representative on
             the jobsite of all accidents which may occur to persons or property and shall provide
             the Construction Manager's representative with a copy of all accident reports on
             appropriate forms. All reports shall be signed by the Trade Contractor or his
             authorized representative and submitted within five (S) days of occurrence.
8.20         MEDICAL SERVICES

8.20.1        TRADE CONTRACTOR'S RESPONSIBILITIES

8.20.1.1      Ensure the availability of medical personnel for advice and consultation.

8.20.1.2      Prior to commencement of work, provisions shall be made for prompt medical attention
              in case of serious injury.



csconTcn774:zna/9s                                   Iv.B-37                             Exhibit 600.1
      Subject:   I        Safety, Rules and Regulations                               Page 38 of 46



8.20.1.3    Ensure that at least one of the Trade Contractor's employees has a valid certificate in
            first aid training from the U.S. Bureau of Mines, The American Red Cross, or
            equivalent training that can be verified by documentary evidence and is available at the
            job site to render immediate first aid. At least one employee capable or rendering first
            aid will be available for each fifteen (15) employees performing work at this site.

8.20.1.4    Ensure that adequate first aid supplies, approved by the consulting physician, shall be
            easily accessible when required.

8.20.1.5    Provide adequate number of first aid kits and supplies approved by the consulting
            physician. First aid kits shall be in a weatherproof container with individual sealed
            packages for each type of item. Contents of the first aid kits shall be checked by Trade
            Contractor before being sent out to the job site and at least weekly during the
            performance of the work to ensure the expended items are replaced.

8.20.1.6     Provide proper equipment for prompt transportation of the injured person to a physician
             or hospital, or a communication system for contacting necessary ambulance service.

8.20.1.7     Telephone numbers and addresses of the physicians, hospital and ambulance shall be
             conspicuously posted.

8.20.1.8     Gilbane Building Company, Rhode Island Airport Corporation and/or its agents) shall
             require a copy and retain on file all "Employer's First Report of Injury". An OSHA 200
             Log for the T.F. Green Airport Project shall be maintained. Trade Contractors are
             advised to maintain their own OSHA 200 Log as a matter of law.

8.20.1.9     Trade Contractor shall ensure that each of its lower-tier Trade Subcontractors meet
             these medical requirements.


8.20.2       FIRST AID & MEDICAL PROCEDURES

8.20.2.1     FIRST AID (MINOR CUTS SCRATCHES, BRUISES, ETC.)

             .l      Each occupational illness or injury shall be reported immediately by Trade
                     Contractor's employee to Trade Contractor's first aid attendant and Gilbane
                     Building Company Project Safety Manager.

             .2      Trade Contractor's first aid attendant or other competent person should treat
                     the injured employee as often as necessary to ensure complete recovery, or the
                     decision is made to seek medical treatment.

8.20.2.2 MEDICAL CASES (NOT REQUIRING AMBULANCE SERVICE)

             .1      Medical cases not normally requiring ambulance services are injuries such as
                     minor lacerations, embedded foreign bodies in eye, minor sprains, strains, etc.


cBCorrFCn77a:2nams                                   IV.B-38                          Exhibit 600.1
     Subject:   I        Safety, Rules and Regulations        I                        Page 39 of 46   11
           .2       Trade Contractor must provide proper equipment for prompt transportation of
                    the injured person to a physician or hospital.
           .3       A representative of Trade Contractor should always drive the injured employee
                    to the medical facility and remain at the facility until the employee is ready
                    to return. Trade Contractor's representative should also carry necessary forms;
                    i.e., authorization slips, return to work notices, etc.
           .4       If it is necessary for the Trade Contractor's first aid attendant to accompany
                    the injured employee, provisions must be made by Trade Contractor to have
                    another employee, properly trained and certified in first aid, to render first aid
                    during the absence of the regular first aid attendant.
           .5       If it is necessary to call the outside medical facility, this call should be made
                    by Gilbane Building Company Project Safety Manager while the injured
                    employee is being transported.
           .6       If the employee is able to return to the job site the same day, he should bring
                    with him/her a statement from the doctor containing such information as date,
                    employee's name, date he/she is able to return to work, regular or restricted
                    duty, date he/she is to return to doctor, diagnosis, signature and address of
                    doctor. If the injured employee is unable to return to the job site the same
                    day, the employee who transported him/her should bring this information back
                    to the job site and report it to Gilbane Building Company, Rhode Island
                    Airport Corporation and/or its agent(s).
           .7       Trade Contractor should designate one employee to keep files on all medical
                    cases and retain all medical statements in this file. The Gilbane Building
                    Company Project Safety Manager will maintain mirror image documents for
                    proper record keeping.
           .8       If the injured employee is released by the doctor for restricted work duty, the
                    Trade Contractor will make available restricted duty work for the injured
                    employee.

8.20.2.3        EMERGENCY CASES (REQUIRING AMBULANCE SERVICES)

            .l      Medical cases requiring ambulance services would be such cases as severe
                    head injuries, amputations, heart attacks, severe bleeding, stopped breathing,
                    etc.

            .2      Should ambulance service be necessary, the following procedures should be
                    taken immediately.

                    .l      Contact Trade Contractor first aid attendant or nearest employee
                            properly trained and certified in first aid.



cscorrFCn77a:2n4/9s                                 IV.B-39                            Exhibit 600.1
       Subject:                Safety, Rules and Regulations                                 Page 40 of 46 J


                        .2     While first aid is being administered,     contact necessary ambulance

                                  service.

8.21          Death (or hospitalization of five or more employees)

              .1        Trade Contractor shall notify the following proper officials immediately.

                        .1        Gilbane Building Company Project Safety Manager,
                        .2        OSHA Representative within 48 hours,
                        .3        Trade Contractor first-aid person.


8.22          SAFETY LOCK & TAG

8.22.1        The Trade Contractor must adhere and strictly follow the T.F. Green Airport Project
              Electrical and Mechanical Lockout and Tagging rules.

              No employee is permitted to work on any energized circuit. All circuit disconnects
              must be locked in the open position and otherwise appropriately identified with affixed
              tags stating "DANGER - DO NOT ENERGIZE" or other equivalent wording prior to
              working on the system or equipment.

              LOCKOUT

              .l        Only individually keyed padlocks shall be used. The Trade Contractor and/or
                        employees) who installed the padlock shall be easily identified at the lockout
                        device.

                  .2    A lockout device of the standard scissor type that will allow the placing of
                        more than one padlock is required, when more than one craft is working on
                        a circuit or mechanical process.

                  .3    A piece of chain or cable may be necessary to complete a lockout on some
                        valves or controls and shall be used wherever needed.

8.22.4            DANGER TAGS

                  .1    'Danger Tags' are not 'Danger Signs', and shall not be used where a sign is
                        needed.

                  .2    Two standardized Danger Tags shall be used on this project. They are
                        described as follows:

                        .1         "DANGER - DO NOT USE": This tag must be attached to each padlock
                                   on a lockout.




cscarrFCn77a:zna/9s                                            Iv.B-4o                   Exhibit 600.1
       Subject: ~            Safety, Rules and Regulations   I                             Page 4l of 46   II
                        .2      "UNSAFE - DO NOT USE": This tag does not require an attachment
                               to a padlock, but may be used if needed. This tag shall be used to
                               identify tools, equipment, vehicles, etc.

8.22.5        PROCEDURE FUNCTION

              .l        If device, valve, switch, or piece of equipment is locked out, a "Danger Tag"
                        shall be attached.

              .2        No device, valve, switch or piece of equipment shall be operated with a
                        "Danger Tag" and/or lockout attached regardless of circumstances.

              .3        Systems consisting of electrical components will be checked, locked and
                        tagged first by electrical craft employee working on the circuit. The electrical
                        craft will be the first lock on, and the last lock off.

              .4        Where placing of lock is not feasible, the circuit conductor will be
                        disconnected from the breaker and tagged out.

              .5        The panel cover shall be of the type that will cover all breakers when closed
                        and shall be equipped with a hasp in order to secure a lock to prevent the
                        panel door from being opened.

              .6        If panel cover is of a type that cannot be locked closed, a cover shall be
                        secured over the panel cover and be locked closed and tagged while any work
                        is being performed on any of those circuits.

               .7       If the above .l through .6 cannot be accomplished, each circuit will be tagged
                        out as prescribed and a electrical department employee will stand by the panel
                        board to prevent breakers from being tampered with. This physical presence
                        will continue daily until the work is complete.

               .8       All "Danger Tags" must be dated, signed and employee's identification
                        number shown. Also on tag, must be the intended work and equipment for
                        which tag has been placed.

                        .I      If employees of more than one craft or crew are to work on a system,
                                circuit, machinery, or component, the supervisor from that craft shall
                                place his individual lock and tag; and verify that the system, circuit,
                                machinery or component being tagged, is indeed the system that is to
                                be worked on.

               .9       Only the person that placed the lock and tag shall remove same without special
                        authorization from the Project Manager, Construction Manager(s), Craft
                        Superintendent or Project Safety Manager.
               .10      Padlocks, Lockout Devices and "Danger Tags" shall be made available as
                        specified in 8.22.3 and .4.
GBCo/rFG/1774:2/14/95                                   I V.B-4 I
                                                                                           Exhibit 600.1
     Subject:   I         Safety, Rules and Regulations        I                        Page 42 of 46   11

           .11      Padlocks shall be color coded for craft identification and shall only be used by
                    that craft for lockout purposes, i.e. valves, switches, electrical components, etc.
           .12      Padlocks shall be issued from the Trade Contractor responsible where a sign
                    in/out log will be maintained. Locks and tags shall be issued to the foremen
                    or supervisor responsible for the craft performing the work. The Trade
                    Contractor of each craft discipline will be responsible for assuring all padlocks
                    are personally identified, that will be used for lock and tag purposes. The
                    Trade Contractor Superintendents) will be responsible for ordering their own
                    craft's padlock. A master key will also be provided.
           .13      Any employees) or persons) found to have removed another's lock and/or tag
                    will be subject to disciplinary action up to and including dismissal from the
                    project.

8.22.6      SPECIAL SITUATIONS

            .1      When due to the nature of work, a supervisor who has employees assigned to
                    work on systems that are between construction and client turnover that are to
                    be locked and tagged out in order to perform work, the below shall be applied:

                    .1      Prior to the electrical foreman de-energizing the system, the foreman
                            will ascertain whether system or device has been turned over and
                            accepted by the client; If system is signed off, the client shall assume
                            responsibility for de-energizing system and becoming the tagging
                            authority.

                    .2      Trade Contractor Electrical foreman/craft journeyman places lock and
                            tag and tries to engage the equipment.

                    .3      The electrical journeyman or lead man will meter the tagged equipment
                            to verify that it is de-energized.

8.22.7      OPERATING FACILITIES & EQUIPMENT

            .1      All systems covered under this section whether electrical, mechanical or others,
                    are considered those systems where no future construction activity is warranted.

            .2      Electrically Operated Systems:

                    .1      Client representative or designee de-energizes system demonstrating
                            accuracy to construction electrical supervisor then locks and tags.

                    .2      Construction electrical foreman/journeyman ascertains that fuses,
                            breakers or throws have been removed, when applicable; tags, locks
                            and tries system.
       Subject:             Safety, Rules and Regulations                               Page 43 of 46

                       .3     Electrical foreman/journeyman, meters the side of the system to be
                              worked on to verify it is de-energized and safe.
                       .4     Upon completion of work, the journeyman removes his/her lock/tag
                              and advises the construction electrical supervisor.
                       .5     Client representative or designee clears system, removes lock and tag
                              and re-energizes if necessary.

8.22.8        OTHER SYSTEMS

              .1       Plant engineer or designee de-energizes system and makes system safe.

              .2       Client mechanics or designees) makes first break in flanges, places blanks,
                       blinds or valves and demonstrates that the system is empty and
                       decontaminated.

              .3       Construction (Client) Coordinator or designee verifies that the system is de-
                       energized and tagged.

              .4       Construction Craft supervisor locks, tags and tries system, surrenders the key
                       to the journeyman who will then perform the assigned task.

              .5       Upon completion of work, the journeyman will return the key to the assigned
                       supervisor and tag and lock are removed.

              .6       Construction (Client) Coordinator or designee assures that system is clear, then
                       removes lock and tag.

              .7       Client mechanics or designees) re-energize system.

8.22.9        CONSTRUCTION

              .1       All systems under this section whether electrical, mechanical or others, are
                       considered those systems that are still in the construction phase.

              .2       Equipment or circuits that are de-energized shall be maintained inoperative at
                       their main power source and shall have locks and tags attached to prevent
                       accidental turn on.

              .3       A staff member shall be designated from the electrical department
                       (Superintendent or General Foreman), to assume the responsibility, for the
                       removal of locks and tags, and activation of power from the main switch gear
                       through end line component.


GBCo/rFG/17742/14/95                                   IV.B-43                          Exhibit 600.1
8.23          DEMOLITION

8.23.1        Prior to starting demolition an engineering survey shall be made to determine the
              condition of the structure and the probability of an unplanned collapse. All utility
              service lines shall be secured out-of-service or otherwise controlled outside the
              building line. Entrances to mufti-level structures shall be protected by sidewalk sheds
              or canopies. Hazardous materials shall be identified and handled in accordance with
              applicable laws, procedures and policies.
8.24          HEATING & VENTILATING
8.24.1        Where heaters are used, particular care shall be taken to provide adequate atmosphere,
              proper combustion and limit to temperature rise. No solid fuel salamanders are
              allowed. Oil-fired heaters shall be equipped with a primary safety control to stop the
              flow of fuel in the event of flame failure. Propane fueled heaters shall have an in line
              regulator to function at approved pressures for the outlet pressure. UL and Gas
              Association approved regulators must be used. An adequate amount of fresh air must
              be provide at all times.
8.25          ENVIRONMENTAL HAZARDS
8.25.1        Material that is designated as a hazardous substance requires special attention by the
              Trade Contractor and workers to minimize the exposure. A plan addressing the
              proper handling, storage and disposal of hazardous material must be developed. The
              Rhode Island Airport Corporation, Gilbane Building Company Project Manager,
              Project Safety Manager, must be immediately notified of any hazardous material leak
              or spill. Any Trade Contractor-caused oil spills must be reported immediately to the
              Gilbane Building Company, Rhode Island Airport Corporation, and/or its agent(s).


8.26           RIGHT TO KNOW

8.26.1         Under the Occupational Safety and Health Administrations (OSHA), workers have a
               right-to-know/obtain information from the Material Safety Data Sheets) (MSDS's)
               prepared by the manufacturer for hazardous materials. Questions arising from the
               "Right To Know" laws should be brought to the attention of the Rhode Island Airport
               Corporation and/or the Gilbane Building Company Project Safety Manager. Verbal
               requests for MSDS information will be responded to on the same day of the request.
               Written requests for MSDS information will be responded to in five (5) working days.




GBCorrFG/1774:2/14/95                            IV.B-44                                Exhibit 600.1
11
11      Subject:                Safety, Rules and Regulations                                                Page 45 of 46



8.26.2         It is the Trade Contractors responsibility to train their employees in those requirements
               as outlined in 29 CFR 1926.59. This training must be documented.
8.26.3         This project is a mufti-employer work site. To this end, a central library is maintained
               for each Trade Contractors' Haz Com Program, Chemical Information List and those
               MSDS's for products utilized on the T.F. Green State Airport Project. This library is
               maintained in the Gilbane Building Company Safety Office. Each Trade Contractor
               is required to maintain their information located in the Gilbane Building Company
               Project Safety Department as well as their own office trailers on site.
8.26.4         Each Trade Contractor is required to implement the provisions of the Right-To-Know
               Law. Before using any material on site listed on the Right-To-Know substance list,
               each Trade Contractor will furnish the Construction Manager with a copy of the
               MSDS for that substance.




8.27           ASBESTOS HANDLING

8.27.1         Occupational Safety and Health Administration (OSHA) regulations have been
               promulgated to protect workers from exposure to airborne asbestos fibers. In the
               event a Trade Contractor believes he has encountered asbestos material, he is to STOP
               work immediately and notify Gilbane Building Company, Construction Manager.

8.27.2         The encapsulation, removal and/or disposal of asbestos material shall be performed by
               a Trade Contractor licensed to do such work in the State of Rhode Island and in
               accordance with all applicable Federal, State and Local regulations per approved
               abatement plans.


8.28               BLASTING2

8.28.1             Under no circumstances shall the Trade Contractor use, transport, or store dynamite,
                   or other explosive materials in carrying out the work to be preformed under this
                   contract.

                   NO EXPLOSIVES WILL BE PERMITTED ON THE AIRPORT PROPERTY




   Z   References: OSHA 29 CFR 1926.900. The "Blasters Handbook" by E. I. Dupont and "Explosives and Rock Blasting" - Atlas
         Powder Company are excellent guides in the use, storage and handling of explosives.


cBCoirFCn77a:2n4rns                                             Iv.s-45                                      Exhibit 600.1
           Subject:            Safety, Rules and Regulations                   --           Page 46 of 46



    8.29          INDUSTRIAL X-RAY RADIOGRAPHY
    8.29.1        The isolation of an area where radiography will be performed shall be accomplished
                  by the use of warning signs, color coded tape, color coded rope (magenta/purple and
                  black), and other appropriate barricades. The locations of barricades will be
                  determined for each particular job by personnel performing the X-ray services. All
                  access points to isolation area will be so marked. All personnel not specifically
                  involved in the radiography must stay out of these barricaded areas.
    8.29.2        All industrial x-rays conducted on the T.F. Green State Airport Project will be
                  conducted after normal work hours.


    8.30          HAZARDOUS MATERIAL/VOLATILE LIQUIDS

    8.30.1        When the use or storage of hazardous materials or equipment is necessary for the
                  execution of the Work, the Trade Contractor shall exercise the utmost care and shall
                  carry on such activities under the supervision of properly qualified personnel.

`   8.30.2        No volatile liquids shall be used for cleaning agents or as fuels for motorized
                  equipment or tools within a building except with the express approval of the
                  Construction Manager.
    8.30.3        Bulk storage of volatile liquids shall be outside the building at locations directed by
                  the Construction Manager. A quantity of volatile liquid not to exceed a total of 120
                  gallons for all Trade Contractors in any one fire area may be stored within the
                  building. Any storage of volatile liquid within the building must be approved by and
                  coordinated with the Construction Manager.




    GBCo/TFG/1774:2/14/95                               IV.B-46                             Exhibit
    f)OO.)<

				
DOCUMENT INFO