Documents
Resources
Learning Center
Upload
Plans & pricing Sign in
Sign Out

SINGLE CARRYCOT INSTRUCTIONS SIN

VIEWS: 27 PAGES: 2

									                                                                                                                                       AMSCis1/8/02gen




                 SINGLE CARRYCOT INSTRUCTIONS
                           IMPORTANT, KEEP FOR FUTURE REFERENCE
These instructions are for the Single Carrycot which fits the following model strollers:
Terrain Single - T1204-000             Urban Single - U1204-000               Rollerbug Single - R1204-000            C:drive Single - C1204-000




      WARNING                                                               Removing Seat
•    Do not use this Carrycot until you have read and un-
     derstood the instructions!                                               All Models
•    Carrycot is suitable for newborn baby to 6 months, or
     until baby can sit up unaided.
•    Before placing baby into position check that the                                                                    seat
     Carrycot is secure and will not tip or fall.                                                                      support
•    Baby must not be in the Carrycot when it is being                                                                  wire.
     fastened or removed from the stroller frame.
•    The depth from the top of the mattress to the top of
     the side of the Carrycot at, or at any position within
     300mm/11.8in from the harness attachment points,
     should not be reduced to less than 140mm/5.5in when                                   A
     the mattress is in position. Mattress purchased
     separately should conform to BS1877 part 10.
•    Do not use accessories not designed for your stroller                                                                       B C
     as they may be unsafe.
•    Do not use the Carrycot to transport children in a
     motor vehicle.
•    Never leave your child unattended.                                      1 Unfasten seat from frame along          3 Push seat forward, then slide
The Sunhood and Seat need to be removed from the stroller before            side tubes.                               fabric off seat support wire.
fitting the Carrycot. Store items removed in a dry safe place.
                                                                            2 Unfasten strap underneath seat at        4 Remove seat support wire
Removing Sunhood                                                            point A (does not apply to Terrain        from stroller frame at B and C.
    All Models                                                              models).




                                                                            Support brackets for Carrycot are different for each
                                                             1              model, except Rollerbug and C:drive use the same brack-
                                                                            ets. Check label on the bracket to ensure you have the
                                                                            correct bracket(s) for your model stroller.
                                                         2


1     Standing beside stroller and       2 Remove support wire 1 from
using a degree of force, pull sunhood   the plastic joint 2 on the side
                                                                                             2                    3
support wire towards you by about       nearest to you.
50mm/2in.                               Then remove wire from the plastic     1                                                                  4
                                        joint on other side.
                                                                                                                                  3
3   Unfasten sunhood fabric from the stroller frame and seat near handle
    bar.
    Fastening Carrycot to Stroller Frame

        Terrain Single Model

                                                                1 Fasten support bracket 1                                      4 Attach Carrycot sunhood
                           1                                    onto frame side tubes                                          to Carrycot by pushing
                                                                immediately above plastic hinge                                sunhood support wire into
                       plastic hinge
                           joint                                joint.                                                         plastic joint on both sides.
                                                                                                                               Place Carrycot onto support
                           2                                    2 Fasten support bracket 2                                     brackets. Ensure Carrycot
                                                                over each side of second                                       sunhood is at the opposite
                                                                fastener (130mm/5ins) up from                                  end from stroller handlebar.
    130mm/5in




                                                                heel rest.                                                     Check that Carrycot rests
                                                                                                                               horizontally, if not check
                          buckle
                                                                    Buckle safety strap between
                                                                                                                      B        position of support brackets
                                                                3  2                                  A
    heel rest                                                   claws on support bracket 2 .                                   are the same as shown in
                                                                                                                               diagram.
                                                                                                                                5 Fasten safety straps to
                                                                                                                               frame at points A & B on
                                                                                                                               both sides (total of 4
                                                                                                                               fasteners).



       Urban Single Model

                                                                1 Remove storage tray under                                   3      Attach Carr ycot
          seat
        support
                                                                stroller by unfastening front end                             sunhood to Carrycot by
          tube                                                  and sliding it off back end of the                            pushing sunhood support
                                                                seat support tube.                                            wire into plastic joint on
                                                                                                                              both sides. Place Carrycot
                                                                2 Slide support bracket 3                                     onto support bracket and
                    3                                           as far as it will go, onto seat                               the front end of seat
                                                                support tube.                                                 support tube. Ensure
                                                                                                                              Carrycot sunhood is at the
                                                                                                                              opposite end from stroller
                                                                                                              A               handle bar. Check that
                                                                                                                  B           Carrycot rests horizontally,
                                                                                                                              if not check position of the
                                                                                                                              support bracket is the same
                                                                                                                              as shown in diagram.
                                                                                                                              4    Fasten safety straps to
                                                                                                                              frame at points A & B on
                                                                                                                              both sides (total of 4
                                                                                                                              fasteners).
       Rollerbug and C:drive Single Models
                                                                                                                              5   Refasten storage tray.

                                                                    1    Remove storage tray                                   5 Attach Carrycot sunhood
                                                                    under the stroller by                                     to Carrycot by pushing
                                                 Buckle
                   3                                        4       unfastening the front end                                 sunhood support wire into
      seat
    support                                                         and sliding off the back end                              plastic joint on both sides.
      tube                                                          of the seat support tube.                                 Place Carrycot onto support
                                                                                                                              brackets. Ensure Carrycot
                                                            t       2 Slide support bracket 3                                 sunhood is at the opposite
                                                         es
                                                      l r           as far as it will go, onto seat                           end from stroller handle bar.
                                                  h ee
                            13                                      support tube.                                             Check that Carrycot rests
                                 0m                                                                                       B
                                      m/
                                           5in                                                                                horizontally, if not check
                                                                    3  Fasten support bracket
                                                                                                          A                   position of support brackets
                                                                    4 over each side of the                                   are the same as shown in
                                                                    second fastener (130mm/
                                                                                                                              diagram.
                                                                    5ins) up from the heel rest.
                                                                                                                              6    Fasten safety straps to
                                                                    4  Buckle safety strap                                    frame at points A & B on
                                                                    between the claws on                                      both sides (total of 4
                                                                    support bracket 4 .                                       fasteners).
                                                                                                                              7   Refasten storage tray.
          WARNING
•         Before placing baby into position check that the Carrycot is secure and will not tip or fall.

								
To top