Docstoc

System Memory Management in Windows CE

Document Sample
System Memory Management in Windows CE Powered By Docstoc
					System Memory Management in Windows CE .NET

Microsoft Corporation


October 2002


Applies to:

  Microsoft® Windows® CE .NET 4.1 and later


Summary: Learn about the design tradeoffs involved in creating Windows CE .NET operating

system (OS) solutions for hardware that implements one of many nonvolatile storage technologies.

Different storage technologies, such as NAND and NOR flash memory, masked ROM, and

electromechanical Advanced Technology Attachment (ATA) or Integrated Drive Electronics (IDE)

storage, impose design constraints and create opportunities for the software environment. (30

printed pages)


Contents



Introduction

Memory and Storage Technologies

NAND Flash Memory

  Conventional Linear or NOR Flash Memory

  Hybrid Flash Memory

  ATA or IDE Hard Disk Drive

XIP vs. Relocatable Code

  ROM Image Builder

  Binary Image Builder File

Image Mapping

  Single Image

  Multiple Region Images

File Systems

Modules Area

  ROM File System

  RAM File System (Object Store)
  External File Systems

  File System Registries

Boot Loaders

  Boot Loaders and Image Storage

  Boot Loaders and Multiple Region Images

  Specialized Boot Loaders

Typical Systems

  Topology A: Linear (NOR) Flash Memory and RAM

  Topology B: Linear ROM and RAM

  Topology C: NAND Flash Memory and RAM

  Topology D: Linear ROM, NAND Flash Memory, and RAM

  Topology E: Linear ROM, Disk Drive, and RAM

Conclusion

For More Information




Introduction

This article gives an overview of the different storage memory technologies, describes the

constraints and opportunities for different memory topologies, and describes the different ways

you can configure the Microsoft® Windows® CE OS image. The article also discusses how storage

memory and the OS can be used together to target specific design criteria such as performance,

power consumption, or upgradeability.




Memory and Storage Technologies

The physical storage you choose for a particular design has significant impact on the cost and

performance of the overall design. Each storage technology imposes design constraints that you,

the software engineer, should be aware of. This section describes the common storage

technologies available and compares and contrasts the features for each technology.


Note   The data for this section was derived from leading vendor publications for both NAND and NOR.
Because of ongoing changes in flash memory technologies, this information is subject to change.
NAND Flash Memory

Toshiba Corporation invented NAND flash memory in the late 1980s and its lower cost per byte and

higher storage sizes are making it a popular flash memory technology for embedded applications

today. The gate design in combination with process technology miniaturization is enabling single

NAND flash memory parts in the upper hundreds of megabytes to be realized at a superior

cost-per-byte ratio.


NAND flash memory is a block-accessed storage device, very much like a conventional

electro-mechanical disk drive with a serial interface. For this reason, NAND flash memory is not

suitable for execute in place (XIP) solutions because the CPU requires program memory to be

linear. Instead, NAND flash memory images are typically moved to DRAM during execution either

at boot time or by OS paging. This ties the cost of NAND flash memory-based devices more closely

to the fluctuating DRAM market prices. It also poses a design problem: how to fetch the initial

pre-boot or OS code at boot time. This can be resolved by adding NOR to the system design, either

in hybrid form or as a separate part, or by using new CPU designs that support streaming the initial

boot code over NAND's serial interface during CPU reset.


A disadvantage to using NAND flash memory is its susceptibility to manufacturing flaws and

run-time cell failures, which show up in the form of bad NAND sectors and/or blocks. Data errors

can also occur during read cycles, which make hardware and/or software data error detection and

correction logic essential in any NAND design. For example, you can correct single bit data errors

through basic Hamming-based error correction codes (ECCs). You can also apply wear-leveling

techniques to limit the number of erase cycles per block. Wear-leveling helps extend the lifespan

of the part by minimizing the number of block erase cycles.


The typically shorter erase and write access times for NAND flash memory over conventional linear

flash memory is an advantage. Read access times for both NAND flash memory and conventional

linear flash memory are comparable. In addition, the erase cycle is typically an order of magnitude

greater than linear flash memory, thereby extending the lifespan of the NAND flash memory part.

This cost-per-byte benefit and the larger storage sizes offset the added complexity involved in the

NAND solution and any additional expense in DRAM.


Conventional Linear or NOR Flash Memory
The storage capacity of NOR flash memory devices is typically smaller than that of NAND flash

memory, but their simpler SRAM-like hardware interface and their lack of manufactured bad blocks

make NOR a suitable choice for certain designs.


NOR flash memory is a random-access storage device with a hardware interface similar to SRAM.

Because of this, NOR flash memory is suitable for XIP designs where the CPU is allowed to fetch

instructions directly from flash memory. While flash memory read access times are slower than

that of DRAM, the performance penalty can be lessened through good design, for example, by

optimizing code for cache usage and running select high-impact code from RAM.


NOR flash memory capacities are typically smaller than NAND due to the basic gate design and to

yield concerns—NOR flash memory is sold without manufactured bad blocks. This tends to limit

capacities while elevating the cost-per-byte ratio. However, for a given design, NOR flash memory

can be advantageous because it does not require additional DRAM or bad block management logic.


The following table shows the per-chip NAND and NOR flash memory attributes.


         Measurement                           NOR                              NAND

Capacity                        1 MB - 16 MB                      8 MB - 128 MB

Performance                     Erase: very slow                  Erase: fast


                                Write: slow                       Write: fast


                                Read: fast                        Read: fast


Reliability                     Less than 10% of the life span of Requires bad block and bit error
                                NAND                              management

Erase cycles range              10,000 - 100,000                  100,000 - 1,000,000

XIP capabilities                Random                            Sequential

Interface                       SRAM-like                         I/O only (serial)



Table 1. NOR and NAND comparison. Source: NAND Flash Technology vs. NOR Flash

Technology, M-Systems.


Hybrid Flash Memory



A number of flash memory manufacturers are trying to combine the best of both NAND and NOR

flash memory technologies on a single device. NAND flashes that support on-chip wear-leveling
and SRAM-like interfaces are now available. NAND parts that support an XIP-able NOR boot flash

memory region can enable a single flash memory part design.


ATA or IDE Hard Disk Drive



The standard ATA or IDE hard disk drive can also be a good choice for image storage. Like NAND

flash memory, disk drives are block-accessed devices. This means that you cannot directly execute

code from disk. Instead, you must copy code to linear memory (DRAM), where you can execute it.

Read and write access times are significantly longer than that of solid-state devices, but the

storage capacity of disk drives is much larger. Many of the software design techniques that you

apply to boot from and dynamically use NAND flash memory with the Windows CE OS also apply

here.




XIP vs. Relocatable Code

You can create individual Windows CE-based components in one of two different forms at build

time: position independent (also called, "relocatable") forms; or fixed position (also called,

"execute in place [XIP]") forms. At run time, the OS loader fixes relocatable code to run at an

available RAM address dynamically chosen by the loader. The benefit is an efficient use of system

RAM without requiring you to explicitly specify the RAM layout. The downside is slightly longer load

times as the OS loader handles the relocation. In addition, you have less flexibility as to where the

code executes from, because code can only be relocated to RAM.


XIP images are fixed position images and are built to run from a specific location. The location must

be accessible in a linear format so that the CPU can fetch instructions; thus, DRAM and NOR flash

memory are possible storage types. XIP images present the possibility of running from flash

memory and thus minimizing RAM usage.


For you to understand how the build tools determine what needs to be XIP and what needs to be

relocatable, you need to understand ROM Image Builder tool (Romimage.exe) and Binary Image

Builder (.bib) files. For more information, see the ROM Image Builder and Binary Image Builder File

topics.
By controlling the compressibility of the constituent OS image components and specifying the

system address range where executable code is to be located, you can control which parts of the

image are XIP and which are relocated at run time. You also have some degree of control over what

runs out of flash memory and what runs from RAM.


When you store images in flash memory, you should compress performance-critical code and

rarely used modules. This will minimize flash memory usage, page the code into RAM at run time,

and thus result in faster access time. Performance-critical code should execute from RAM without

demand paging. Critical code should be either loaded completely by the OS loader instead of

demand paging, or copied into RAM by a boot-time loader.


ROM Image Builder



The ROM Image Builder tool, Romimage.exe, is a build tool for Windows CE that runs in the final

phase of the build process. Romimage.exe performs the following functions:


       Collects all the requisite components that make up the final image including drivers,
    executables, and data files

       Performs fix-ups on any executable code in a space efficient manner, thus detailing where code
    will execute from by default

       Compresses parts of the image

       Places any data files or compressed sections in address holes between aligned components

       Generates the Nk.bin image, which is placed on the target platform


Configurable .bib files mainly drive the whole process.


Binary Image Builder File



A binary image builder (.bib) file specifies the files and components placed in the final, built OS

image. The file also includes information about attributes that dictate how the OS handles each file

and component. For example, the file includes information about decompressing images or pages

in the whole module at load time, and choosing where the files and components are loaded in the

virtual address space. A .bib file is composed of three sections: MEMORY, MODULES and FILES.


MEMORY section
The MEMORY section of a .bib file, specified in Config.bib, details the system addresses available to

the OS. Each board support package (BSP) contains one copy of Config.bib. The following code

example shows a MEMORY region entry.


 Copy Code

       NK          80001000       01FFF000       RAMIMAGE
       RAM         82000000       01DB0000       RAM

The RAMIMAGE entry tells Romimage.exe to locate any executables, modules, data files and

compressed sections in the range of virtual address 0x8000.1000 through 0x81FF.FFFF. These

addresses can physically correspond to RAM or to linear flash memory. The RAM entry specifies the

range of virtual addresses available to the Windows CE kernel for allocation to the file system or

object store, process virtual address spaces such as heaps and stacks, memory mapped files and

writable data sections. Once you run Romimage.exe, all non-compressed executable code is fixed

up to run at a virtual address in slot 0 with the code actually residing within the range of addresses

specified in the RAMIMAGE entry. Slot 0 is an address space created by the Windows CE kernel.


MODULES section



The MODULES section of a .bib file informs Romimage.exe about which files to load into the final

image and how to load them into the memory range specified in the MEMORY section. The following

code example shows an entry in the MODULES section.


 Copy Code

INIT.EXE        %_WINCEROOT%\RELEASE\INIT.EXE                  NK    SH
MYDLL.DLL       %_WINCEROOT%\RELEASE\MYDLL.DLL                 NK    SHC

The entries inform Romimage.exe to include Init.exe and Mydll.dll in the OS image. More

specifically, the entries tell Romimage.exe to locate both files in the section labeled NK, which is in

the RAMIMAGE range as specified in the MEMORY section entry. The C flag in the second

MOUDULES section entry also specifies that Romimage.exe needs to compress Mydll.dll. For more

information about flags used in the MODULES section, see MODULES Section in Windows CE .NET

Help. By compressing Mydll.dll, Romimage.exe is informing the kernel that it needs to uncompress,

perform any run-time fix-ups, and demand page the image into RAM. If the compressed file is

already in RAM, that is, the RAMIMAGE section maps to RAM, then Mydll.dll is occupying two areas

of RAM. However, the compressed image can be in flash memory.
FILES section



The FILES section of a .bib file is similar to the MODULES section. However, Romimage.exe

compresses all entries by default. The FILES section is typically comprised of data files that are

loaded into application processes, for example, waveform audio files (.wav) and bitmaps. The

following code example shows an entry in the FILES section. It instructs Romimage.exe to include

Initobj.dat in the image and to compress it.


 Copy Code

INITOBJ.DAT       $(_FLATRELEASEDIR)\RELEASE\INITOBJ.DAT                    NK    SH

There is a key difference between placing a file in the MODULES section over placing a file in the

FILES section. Namely, any dynamic-link libraries (DLLs) in the MODULES section will be loaded

into process slot 1 of the Windows CE virtual memory map. Process slot 1 is a 32 MB address space

set aside specifically for these modules and therefore provides significant space for storing DLL

code used across the system. Any DLLs placed in the FILES section will be loaded into every slot

location and thus decrease the virtual address space available to any one process. For more

information about Windows CE processes and virtual memory design, see this Memory

Architecture in Windows CE .NET Help.




Image Mapping

At run time, OS components are fetched from the addresses chosen by Romimage.exe at build

time. These components can be executed in place provided they exist in CPU-accessible linear

memory or they can be paged into RAM by the OS loader. Romimage.exe and the .bib file controls

the location from which components are fetched and the manner in which the original is organized.

More specifically, the .bib file allows you to control the segmentation and layout of the entire OS

image. For example, rather than having a single monolithic Nk.bin image, you may want to

organize the components into individual regions: Nk.bin, for kernel, file system and other critical

components; IE.bin, for Internet Explorer components; and Apps.bin, for any custom applications.

By arranging your OS image in this way, you can update areas individually, control access to

special areas and provide an additional way to map components through paging or through XIP.


Single Image
By default, Romimage.exe will generate a single Nk.bin file. Though this file may contain

compressed modules, which will be paged into RAM at run time by the OS loader, anything that is

uncompressed will run XIP from the address range specified in the MEMORY section of the .bib file.

If the XIP areas are physically in RAM, but the image is stored in some non-volatile storage such as

flash memory, then code is required—either a boot loader or early OS startup code—to copy the

image from non-volatile storage to the correct RAM location per Config.bib where execution

continues.


When updating any part of the image, you need to update the entire Nk.bin file. This can be a bit

dangerous, for example, if you only want to update an application, but have to perform a flash

memory operation on the entire OS image. A better solution might be to locate applications that

may need periodic updates in a separate image region. Other than dealing with linear flash

memory limitations of executing in place while updating flash memory, it could then be possible to

close the running application, update just the application region, then restart the application

without ever touching the kernel and without rebooting.


Multiple Region Images



With a multi-region image, you have finer control over the image layout, can control region

updates, and can decide on a per-region basis how the OS will access that region when it pages its

components at run time. For example, you may want to have the OS loader page in modules from

a region through a low-level flash memory file system driver or through a more conventional FAT

file system in flash memory. The File Systems topic describes these file system concepts. Creating

a multi-region image requires .bib and OEM adaptation layer (OAL) source modifications.


Multiple region BIB changes



To specify the number of image regions and their locations, you need to modify the MEMORY

section of the .bib file, Config.bib, to describe the starting address and length of each region. The

following code example shows how you can do this.


 Copy Code

    NK           80220000 008de000            RAMIMAGE
    CHAIN        80afe000 00001000            RESERVED
    EXT2         80aff000 00001000            RAMIMAGE
    EXT          80b00000 00100000            RAMIMAGE
    RAM          80c00000       01000000       RAM

The above MEMORY entries tell Romimage.exe that four image regions need to be created: NK, for

the kernel and core OS files, EXT2, EXT and CHAIN. The size specified for each region is the

maximum size of that region. When updating a region, code and data sizes can increase up to the

limit specified in the MEMORY section. Once a multi-region image is created, the MEMORY values

should not be altered in order for future builds to remain compatible. The above example MEMORY

entries also indicate where the RAM managed by the kernel resides. For this example, RAM resides

in 0x80C0.0000 through 0x81BF.FFFF.


Each multi-region image requires a CHAIN region where a chain file resides. The chain file is a list

containing information about each of the image regions. It is available to the kernel through the

OAL and provides a way for the OS to know about the files and modules that make up each region.

In the MEMORY section, you need to define a fix-up variable that is ultimately used by the OAL to

know where Romimage.exe places the chain file. This allows you to avoid hard coding the address

in the OAL. Note that the value assigned to the variable should match the start of the CHAIN region

defined in the above code example.


The following code example shows how you can define a longword pointer LPDWORD pdwXIPLoc

in your OAL code, and assign it the value 0x80AF.E000, which corresponds to the start of the

CHAIN region.


 Copy Code

    pdwXIPLoc 00000000            80afe000       FIXUPVAR

After defining a fix-up variable, you need to add entries in the CONFIG section of the .bib file, which

tell Romimage.exe where the chain file needs to be placed and to help with automatically sizing

module images. The following code example shows the entries you need to add in the CONFIG

section.


 Copy Code

XIPSCHAIN=80afe000
DLLADDR_AUTOSIZE=ON

The XIPSCHAIN variable should point to the start of the CHAIN region defined in the MEMORY

section.
Last, you should tag the .bib entry for each component with the name of the region in which it is

to reside. The following code example shows how you can do this.


 Copy Code

pcmcia.dll            $(_FLATRELEASEDIR)\ti1250.dll                           EXT SH
ensoniq.dll           $(_FLATRELEASEDIR)\ensoniq.dll                          EXT SH
iesample.exe          $(_FLATRELEASEDIR)\iesample.exe                         EXT2 S

In the above example, the PCMCIA and Ensoniq drivers are placed in the EXT region and IESample

is placed in the EXT2 region. You can modify both the MODULES and FILES sections in this way to

organize files between the various regions. Each region definition results in a single .bin file that

includes its own table of contents, which describes in detail each of the files in the region. The chain

file in turn provides a way to enumerate the entire table of contents across all regions and thus

gives the kernel a way to locate any file in the image.


Multiple region OAL changes



The Windows CE kernel is informed of the existence of multiple image regions during OAL

initialization, specifically, during OEMInit. The kernel exports a pointer, that when assigned to an

array of structures that each point to a specific region's table of contents, provides the kernel with

a way to enumerate all the files in an image across region boundaries. The following code example

demonstrates how this is done.


Note   The code example uses the fix-up variable pdwXIPLoc, which is discussed in the Multiple region
BIB changes topic.
 Copy Code

#define NOT_FIXEDUP                       (DWORD*)-1
#define MAX_ROM                           32 // Maximum number of regions.
#define ROMXIP_OK_TO_LOAD                 0x0001

// ROM chain pointer exported by the kernel library
extern ROMChain_t      *OEMRomChain;

// Fix-up variable (corresponds to variable in Config.bib)
DWORD *pdwXIPLoc = NOT_FIXEDUP;

void InitRomChain()
{
    static ROMChain_ts_pNextRom[MAX_ROM] = {0};
    DWORD dwRomCount = 0;
   DWORD dwChainCount = 0;
   DWORD *pdwCurXIP = 0;
   DWORD dwNumXIPs = 0;
   PXIPCHAIN_ENTRY pChainEntry = NULL;

   // Verify that Romimage.exe fixed up chain file pointer
   if(pdwXIPLoc == NOT_FIXEDUP)
   {
       return; // No chain or not fixed up properly
   }

   // Set the top bit to mark it as a virtual address
   pdwCurXIP = (DWORD*)(((DWORD)pdwXIPLoc) | 0x80000000);

   // First DWORD is number of XIP regions.
   dwNumXIPs = (*pdwCurXIP);

    // Make sure number of XIP regions does not exceed our maximum
    if(dwNumXIPs > MAX_ROM)
    {
        lpWriteDebugStringFunc(TEXT("ERROR: Number of XIP regions exc
eeds
          the maximum.\n"));
        return;
    }

   // Point to the first XIP region chain entry
   pChainEntry = (PXIPCHAIN_ENTRY)(pdwCurXIP + 1);

   // Skip first entry because loader will add that in for
   // us (this is the kernel region)
   ++pChainEntry;
   dwChainCount++;

   while (dwChainCount < dwNumXIPs)
   {
       // If region is a valid XIP region and signature
       // matches, then proceed.
       if ((pChainEntry->usFlags & ROMXIP_OK_TO_LOAD) &&
         *(LPDWORD)(((DWORD)(pChainEntry->pvAddr)) +
           ROM_SIGNATURE_OFFSET) == ROM_SIGNATURE)
       {
           s_pNextRom[dwRomCount].pTOC =
             *(ROMHDR**)(((DWORD)(pChainEntry->pvAddr)) +
                      ROM_SIGNATURE_OFFSET + 4);
                  s_pNextRom[dwRomCount].pNext = NULL;

                  if (dwRomCount != 0)
                  {
                      s_pNextRom[dwRomCount-1].pNext = &s_pNextRom[dwRomCou
nt];
                  }
                  else
                  {
                      OEMRomChain = s_pNextRom;
                  }
                  dwRomCount++;
            }
            else
            {
                  lpWriteDebugStringFunc(TEXT("Invalid XIP region found.\n
"));
            }

         ++pChainEntry;
    dwChainCount++;
     }
}

If OEMInit calls the InitRomChain function, InitRomChain will register the multiple XIP regions

with the kernel, and thus provide a complete picture of the entire image. For more information

about the InitRomChain function see the ROMChain_t and ROMHDR structures, which are

defined in %_WINCEROOT%\Public\Common\Oak\Inc\Romldr.h.


Building and using multiple region images



Once you build the multiregion image, it takes the form of five different .bin files: Chain.bin, Nk.bin,

Ext.bin, Ext2.bin and Xip.bin. The first four files contain the files allocated to each of the defined

regions. The last file, Xip.bin, is a composite image made up of the first four files and exists only to

make the initial download to the target device easier.


Once you store the entire image on the target device, you can update individual regions by

downloading only the affected .bin file for a region. You can download the initial image and update

images from boot loaders to OS applications in different ways. Boot loader options are discussed in

more detail in the Boot Loaders topic.
File Systems

Windows CE supports file systems based on file allocation tables (FATs). The FAT driver works with

any external storage cards that you can plug into your target device, such as Advanced Technology

Attachment (ATA) and linear flash memory cards. These are mainly PC Cards. The cards can

contain a file system partitioned into sections. Each section is mounted as a FAT volume and placed

under a special folder in the root directory. The device driver associated with the card provides the

name of the mounted folder. If a name is not provided, the name Storage Card is used to mount

the file system.


You can place file system components in four different areas: execute in place (XIP), ROM File

System, Object Store, and External File System.




Modules Area

The modules area is the area that is true XIP. Modules that are placed in the XIP area are loaded

by the ROM-image into RAM in the order specified. This is advantageous for your system, as it does

not take up space in the virtual memory of a process. If there is no available RAM, the system will

use virtual memory of a process by default. Modules placed in the XIP area are uncompressed by

default. However, compressed modules will be handled in the same fashion as uncompressed

modules.


ROM File System



The file system manages all components that are defined in the FILES section of the .bib file for

your image. You can choose to compress these components by enabling OS compression. By

default, processes and modules that are loaded from the ROM file system area are paged. Modules

will not be paged if they are loaded using the LoadDriver function. They will instead be copied into

RAM to be executed. Any module loaded from this area will use virtual memory space in all

processes.


RAM File System (Object Store)
The object store, or RAM file system, is a memory area that has both read and write capabilities

and is generally located in RAM with a battery-backup. All files that are placed in the object store

are compressed by default. In order to turn off compression, you must specify nknocompr instead

of nkcompr as your kernel component. Individual files can be stored uncompressed by using the

FILE_FLAG_RANDOM_ACCESS flag when the file is created. By default, processes and modules

that are loaded from the object store area are paged. Modules will not be paged if they are loaded

using the LoadDriver function. They will instead be copied into RAM to be executed. Any module

loaded from this area will use virtual memory space in all processes.


External File Systems



An external file system is a file system that is mounted externally and managed by the file system

driver manager (fsdmgr). Microsoft currently provides the FAT file system (FATFS) and the

Universal Disk file system (UDFS) for external file systems. FATFS is supported for all block devices,

while UDFS is a file system used for DVD-ROMs. UDFS also includes the compact disk file system

(CDFS) for CD-ROMs. You can also use file systems provided by other vendors as well. In order to

support paging for external file systems you must implement the ReadFileWithSeek and

WriteFileWithSeek functions. The following registry entry can be used to enable file system

paging.


 Copy Code

[HKEY_LOCAL_MACHINE\System\StorageManager\<filesystem>]
     "Paging"=dword:1

You can also disable file system paging by setting the Paging registry entry to 0. You can modify

the behavior of a file system for a specific profile by altering the registry entry for that profile. The

following registry entry controls the behavior of a file system.


 Copy Code

[HKEY_LOCAL_MACHINE\System\StorageManager\Profile\<profilename>\<file
syste
  m>]
      "Paging"=dword:1

File System Registries
When selecting the registry for your device, three registry options are available: the RAM-based

(object-store-based) registry, the hive-based registry and the SRAM registry. The registry type in

use is invisible to applications, but it will change the persistence, boot sequence and speed, and

memory usage on your device. As a result, choosing the correct registry will improve your device

characteristics and behavior.


Object store registry



The object store registry is a RAM-based registry solution that can be set to persist by adding

support in the OEM adaptation layer (OAL). This can be accomplished by implementing

pReadRegistryFromOEM and pWriteRegistryToOEM functions in the OAL. When the registry is

flushed using the RegFlushKey function, the file system enumerates through the entire registry

and calls the pWriteRegistryToOEM function for each element. Upon initialization, the file

system restores the registry by calling the pReadRegistryFromOEM function. The process of

setting the registry to be persistent in the OAL as well as the restoring of the registry occurs before

any other system components are loaded, with the exception of the kernel and file system. A last

known good (LKG) configuration can be created by saving the registry using the RegCopyFile

function and later restoring it using RegRestoreFile.


Hive-based registry



A memory-mapped file on a target file system implements the hive-based registry. If the

StartDevMgr registry value is set in HKEY_LOCAL_MACHINE\init\BootVars then the file

system mounts the registry on an external location. If the StartDevMgr registry value is not set,

the file system uses the object store registry. Only the changes that have been made to the ROM

registry, or deltas, are saved in the hive. The registry can be saved and restored on the hive-based

registry using RegSaveKey and RegReplaceKey. This is advantageous in an LKG scenario, as it

requires a system reboot.


SRAM registry



The SRAM registry is nearly identical to the hive-based registry except that the hive points to a

specific section of SRAM. If the OAL implements IOCTL_HAL_GET_HIVE_RAM_REGION then

the file system will use the specified RAM region. The SRAM registry is typically backed with a
battery, but to have true persistence, the contents of the SRAM registry must be stored on a

permanent storage device. The persistence of this type of registry is left up to the OEM.




Boot Loaders

The boot loader is used to place the OS image into memory and to jump to the OS startup routine.

The boot loader can obtain the OS image in a number of different ways, including loading it over a

cabled connection, such as Ethernet, universal serial bus (USB) or serial. The boot loader can also

load the OS from a local storage device, such as flash memory or a disk drive. It may store the

image in RAM or in nonvolatile storage, such as flash memory or a disk drive, for later use.


In a retail device, the boot loader allows a kernel image to be compressed and/or built for a location

other than where it is stored, for example, the kernel image is built to run from DRAM, but stored

in compressed form in NAND flash memory. While the boot loader does not have to be the primary

means of updating the OS image, its availability as a failsafe loader means that there is always an

update mechanism to fall back on.


The next few topics discuss a few of the common loader features that apply when running Windows

CE from a variety of storage devices, discuss the multi-region image as it affects boot loaders, and

describes two specialized boot loaders which are provided with Windows CE.


Boot Loaders and Image Storage



Typically, the boot loader is the first bit of code to run on a device after hardware reset with the

possible exception of BIOS/POST code. The boot loader is responsible for locating, loading, and

executing the OS image. The loader typically resides in CPU-accessible linear memory, although

there are instances where the loader resides on a block-accessed device such as a disk drive or

NAND flash memory, for example, the BIOS boot loader which relies on the PC BIOS bootstrap

process to load it into RAM and execute it. Though the bootstrap process could easily load the OS

image, the boot loader can provide some additional benefits in a retail device scenario.


When searching for a valid OS image to load, the boot loader will typically look in local storage first.

Verifying that an image is valid can involve checking the signature of the stored image—such as
hashing the important contents of the image and then generating a digital certificate, which is

compared against the image—or can be based on a simpler validation like a checksum.


The type of storage device and the manner in which the image is stored on the device dictates the

support required in the loader. For example, in one of the simplest cases, the OS image could be

stored uncompressed in NOR flash memory and after verification, be executed by simply jumping

to the starting address in flash memory. A more complex scheme could involve finding and

decompressing the kernel region of a multi-region image in NAND flash memory and moving it to

RAM where it is executed. The choice as to how the image is stored and on what type of storage

device is driven by cost, performance, and upgradeability concerns. For more information about

design tradeoffs, see the Typical Systems topic.


In failsafe scenarios where the boot loader cannot locate a valid image in local storage, the loader

typically turns to a local cabled connection such as Ethernet or USB over which it can download a

known good image and then write to local storage. Because the stored boot loader image typically

either resides in a separate and protected memory device or resides in a special area of general

storage, the size of the boot loader is generally restricted. This means that more sophisticated

networking features are the domain of the OS. While the OS can coordinate download and updates

with the boot loader, the boot loader typically implements a simple test of network features as a

failsafe measure. For example, an application under the OS can download an update over HTTP

into RAM, but because some flashes cannot be updated while being executed from, the application

might set a flag to communicate with the boot loader and reboot the system, thus letting the boot

loader update the device.


When downloading and/or performing a flash memory operation on the image updates, the loader

is typically tasked with validating the image first, possibly using checksums and signatures.

Because typical flash memory erase and write times or disk drive writes can be significant,

downloaded images are often cached temporarily in DRAM before being written to storage.

Checksums and signatures are often verified in DRAM.


If the storage device is unprepared, the next steps performed by the boot loader typically depend

on the design of the OS image. For example, if the OS image makes use of a flash memory file

system driver to page code from a region of NAND flash memory into DRAM, that file system may

require that the device be partitioned and formatted with logical to physical sector numbering. Bad
blocks may also need to be identified and marked so that the file system knows to ignore them.

Ultimately, it is the boot loader's responsibility to ensure that the storage device is prepared in a

manner consistent with what the OS image is expecting. Once done, the downloaded image is

stored.


Boot Loaders and Multiple Region Images



Multi-region images require the boot loader to be able to differentiate between the different .bin

files and update only the pertinent regions of storage with the updated image. The .bin file format

makes this relatively easy. The following table shows more information about the .bin file format.


                Field                 Length (bytes)                       Description

Sync bytes (optional)            7                          Byte 0 is B, indicating a .bin file format.


                                                            Bytes 1-6 are reserved and set to 0, 0,

                                                            0, F, F, \n.


Image address                    4                          Physical starting address of the image.

Image length                     4                          Physical length, in bytes, of the image.

Record address                   4                          Physical starting address of the data
                                                            record. If this value is zero, the record
                                                            address is the end of the file, and record
                                                            length contains the starting address of the
                                                            image.

Record length                    4                          Length of record data, in bytes.

Record checksum                  4                          Signed 32-bit sum of record data bytes.

Record data                      Record length              Record information.



Table 2. Binary Image Builder (.bin) record format


The image header consists of the image address and image length. One or more records consist of

the record address, record length, record checksum and record data. The .bin file is composed of

a master header and a series of records, with each record having a header that specifies the

location it is to be written to along with a length and a checksum value. Romimage.exe computes

the header addresses based on the MEMORY section in Config.bib. For example, given the following

code example in the MEMORY section:


 Copy Code
     NK           80001000       01FFF000      RAMIMAGE
     RAM          82000000       01DB0000      RAM

You will receive the following output from Romimage.exe:


 Copy Code

<cut>
Physical Start Address:             80001000
Physical End Address:               8122bed0
Start RAM:                          82000000
Start of free RAM:                  82032000
End of RAM:                         83db0000
<cut>

The output from Romimage.exe results in a .bin file that consists of the following records:


 Copy Code

Image Start = 0x80001000, length =                0x0122AED0
Record [ 0] : Start = 0x80001000,                 Length = 0x00000014, Chksum =
  0x000002B1
Record [ 1] : Start = 0x80001040,                 Length = 0x00000008, Chksum =
  0x000002C5
Record [ 2] : Start = 0x80002000,                 Length = 0x00139014, Chksum =
  0x04D28C9C
Record [ 3] : Start = 0x8013C000,                 Length = 0x000000A4, Chksum =
  0x00000C30
<cut>

In a multi-region image, the .bin record addresses are unique across the various regions.

Romimage.exe enforces this when you define the MEMORY section in Config.bib. As such, caching

the image and uniquely locating the final storage location of the image on the device can be derived

from the .bin record addresses, with consideration given to any non-zero ROMOFFSET value.


ROMOFFSET is a .bib file CONFIG section variable. Its purpose is to differentiate where an image is

stored on a device versus where it is executed from. Romimage.exe reads the value assigned to

ROMOFFSET and applies that offset value to the computed .bin record addresses. This is useful, for

example, if you want the image to execute in place from DRAM, thus requiring RAM-based fix-up

addresses, but want to store the image itself in flash memory under the assumption that a loader

or the OS startup code will copy the image to RAM at run time. Occasionally, it is important for the

boot loader to figure out not only where the downloaded region should be stored, but also where

it should be copied during run time. By knowing the ROMOFFSET value, you can determine the
location. The following code example is from the BLCOMMON boot loader library and it

demonstrates one way to compute ROMOFFSET.


    Copy Code

#define ROM_SIGNATURE_OFFSET 64
#define ROM_SIGNATURE        0x43454345

// Look for ROMHDR to compute ROM offset. NOTE: Romimage.exe guarante
es
  that the record containing
// the TOC signature and pointer will always come before the record t
hat
  contains the ROMHDR contents.
//
if (dwRecLen == sizeof(ROMHDR) && (*(LPDWORD) OEMMapMemAddr(dwImageSt
art,
  dwImageStart + ROM_SIGNATURE_OFFSET) == ROM_SIGNATURE))
{
    DWORD dwTempOffset = (dwRecAddr –
      *(LPDWORD)OEMMapMemAddr(dwImageStart, dwImageStart +
        ROM_SIGNATURE_OFFSET + sizeof(ULONG)));
    ROMHDR *pROMHdr = (ROMHDR *)lpDest;

    // Check to make sure this record really contains the ROMHDR.
    //
    if ((pROMHdr->physfirst == (dwImageStart - dwTem
pOffset)) && (pROMHdr->physlast == (dwImageStart - dwTempOffset +
dwImageLength)) && (DWORD)(HIWORD(pROMHdr->dllfirst << 16) <= pROMHdr
-
>dlllast) && (DWORD)(LOWORD(pROMHdr->dllfirst << 16)<= pROMHdr->dllla
st))
    {
        g_dwROMOffset = dwTempOffset;

            EdbgOutputDebugString("rom_offset=0x%x.\r\n", g_dwROMOffset);
       }
}

OEMMapMemAddr is of only slight interest in this case—it maps the image to a temporary RAM

cache address before the image is stored. The .bin file headers provide the dwImageStart and

dwRecAddr parameters. The algorithm attempts to locate the .bin record that contains the

ROMHDR region by size then compares the contents of the record to known image characteristics
and the offset is computed by taking the difference between the ROMHDR .bin file record start

address and the actual location from which the ROMHDR was built for run time.


Lastly, an important aspect of handling multi-region image updates is to know during image

update or download which region contains the kernel. This is often important in cases where the

loader will be the one copying the kernel image to DRAM at reset. By locating the kernel region,

saving the storage address, ROMOFFSET and start address, the loader has most of the information

it needs to load and start the kernel at boot time. The following code example demonstrates

whether it contains the Windows CE kernel given a region start address and length.


 Copy Code

static BOOL IsKernelRegion(DWORD dwRegionStart, DWORD dwRegionLength)
{
   DWORD dwCacheAddress = 0;
   ROMHDR *pROMHeader;
   DWORD dwNumModules = 0;
   TOCentry *pTOC;

    if (dwRegionStart == 0 || dwRegionLength == 0)
       return(FALSE);

    if (*(LPDWORD) OEMMapMemAddr (dwRegionStart, dwRegionStart +
      ROM_SIGNATURE_OFFSET) != ROM_SIGNATURE)
       return FALSE;

   // A pointer to the ROMHDR structure lives just past the ROM_SIGNA
TURE
      (which is a longword value). Note that
   // this pointer is remapped because it might be a flash memory add
ress
      (image destined for flash memory), but is actually cached
   // in RAM.
   //
   dwCacheAddress = *(LPDWORD) OEMMapMemAddr (dwRegionStart, dwRegion
Start
      + ROM_SIGNATURE_OFFSET + sizeof(ULONG));
   pROMHeader      = (ROMHDR *) OEMMapMemAddr (dwRegionStart,
      dwCacheAddress);

    // Make sure sure are some modules in the table of contents.
    //
    if ((dwNumModules = pROMHeader->nummods) == 0)
        return FALSE;

     // Locate the table of contents and search for the kernel executab
le
       and the TOC immediately follows the ROMHDR.
     //
      pTOC = (TOCentry *)(pROMHeader + 1);

     while(dwNumModules--) {
        LPBYTE pFileName = OEMMapMemAddr(dwRegionStart, (DWORD)pTOC-
          >lpszFileName);
        if (!strcmp(pFileName, "nk.exe")) {
           return TRUE;
        }
        ++pTOC;
     }
     return FALSE;
}

In the above code example, OEMMapMemAddr simply maps the storage address to a temporary

RAM cached address, where it is kept before being written to final storage.


Specialized Boot Loaders



Microsoft provides boot loaders with particular specialties in addition to the standard Ethernet boot

loader provided with each BSP. Currently, these specialized boot loaders only address the needs of

x86 platform solutions.


x86 ROM boot loader



The x86 ROM boot loader (romboot) is a small boot loader that resides in the system flash memory

part, usually a 256 KB flash memory/EEPROM. During power-on, it handles the platform

initialization tasks that would normally be done by the platform BIOS. Once the platform is

initialized, romboot supports downloading an image over Ethernet or loading the image from a

local IDE drive.


Because romboot is designed to reside in the flash memory, where the BIOS normally resides, the

boot loader replaces the BIOS. This means that there are no BIOS features available to the OS. It

also means that romboot configures the platform. This task includes setting up the memory

controller, host bridge and PCI enumeration.
The primary advantage of using romboot is that it is a very fast-booting loader solution. Romboot

is an alternative to LoadCEPC.exe and is designed to not require BIOS or Microsoft MS-DOS®

services for the x86 platforms that it supports, thus providing a faster boot and download

alternative. The loader currently supports the Lanner EM-350 and EM-351 Embedded SBCs and

Advantech PCM-5822 and PCM-5823 Biscuit PC systems, though it can be extended to support

many other chipsets. For more information about the systems supported by boot loader, see

Lanner EM-350 and EM-351 Embedded Single Board Computers and Advantech PCM-5822 and

PCM-5823 Biscuit PC.


The boot loader supports downloading an image over an Ethernet connection, getting its IP

address through the Dynamic Host Configuration Protocol (DHCP) or by static IP, as well as from a

local IDE/ATA hard disk. You should place the NK.bin image in the root directory of the active

partition when loading from a hard disk.


You can find code for the ROM Boot Loader at the following locations:


        Build files (BIB, batch, and others): %_WINCEROOT%\Platform\Geode\Romboot

        Common boot loader code: %_WINCEROOT%\Public\Common\Oak\CSP\i486\Romboot

        Geode/MediaGX code: %_WINCEROOT%\Public\Common\Oak\CSP\i486\Geode\Romboot


For more information about the x86 ROM boot loader,

see %_WINCEROOT%\Platform\Geode\Romboot\Readme.txt and x86 ROM Boot Loader in

Windows CE .NET Help.


x86 BIOS boot loader



The x86 BIOS boot loader (biosloader) is an alternative to romboot. Unlike romboot, biosloader

does not replace the system BIOS. Rather, it uses the BIOS services like the VESA BIOS for video

display control and INT 13h services for disk I/O to load an image from a local storage device. It will

load a BIN image from any device that the BIOS exposes INT 13h support for and views as a

storage device. This currently includes floppy, hard disk, Compact Flash (CF), and Disk-On-Chip.

The boot loader resides on a bootable storage device and is found and loaded by a boot sector

image.


For more information about the BIOS boot loader and the boot process, see x86 BIOS Boot Loader

in Windows CE .NET Help.
Typical Systems

Systems used today combine flash memory, ROM, RAM and disk storage in many different ways.

This topic describes a few of these memory topologies and the various ways in which you can

configure the Windows CE OS. It also includes a summary that reviews the design trade-offs,

including performance, power, and upgradeability, involved in supporting each topology.


The summaries make some basic assumptions about the relative differences between the various

memory devices. More specifically, for the memory types described in this article, the following

assumptions are made:


        Read access times increase with device type in the following order: SDRAM, flash memory
     (NAND and NOR are not differentiated, it depends on read mode) and then disk drives.

        For the non-volatile memory types, erase and write times or the ability to update data, increase
     with device type in the following order: NAND flash memory, NOR flash memory, and then disk drives.
     SDRAM has the fastest erase and write times.

        Operating power consumption increases with device type in the following order: disk drives,
     SDRAM, NOR flash memory and then NAND flash memory.

        NAND flash memory does not support executing code in place from the flash memory part and
     thus typically requires a linear non-volatile memory solution such as NOR flash memory or ROM for
     boot-time initialization. NAND vendors offers hybrid designs like NAND flash memory with a small
     NOR boot block or logic designs that enable a CPU to read from a particular good NAND block at reset
     time to address this issue.


The following table shows the various memory topologies discussed in this topic.


    Memory topologies

Topology A                 Linear (NOR) flash memory and RAM

Topology B                 Linear ROM (not writeable) and RAM

Topology C                 NAND flash memory and RAM

Topology D                 Linear ROM (not writeable), NAND flash memory, and RAM

Topology E                 Linear ROM (not writeable), disk drive, and RAM



Table 3. Common system memory topologies


Topology A: Linear (NOR) Flash Memory and RAM



In this configuration, NOR flash memory provides non-volatile storage. Typically there is no BIOS

or boot loader present; this means that code execution will need to start from the NOR flash
memory at CPU reset, thus prohibiting compression of the entire image to save space and perhaps

allow for a smaller NOR part.


OS configurations



For this memory topology, you can configure the Windows CE OS in the following ways:


       XIP everything from NOR and use RAM for file system, object store and program memory.


    This configuration supports the ability of NOR flash memory to store code that can be fetched

    directly by the CPU. The NOR flash memory is physically located at an address visible to the

    CPU at reset time and thus execution starts and proceeds from a known location in NOR flash

    memory. Because the kernel executes directly from NOR flash memory, this does not impose

    the requirement that a monitor or boot loader be present to relocate the kernel image to RAM.


    To create an OS configuration of this type, the platform's Config.bib MEMORY section should

    indicate the available NOR flash memory address range with the RAMIMAGE keyword and the

    available RAM address range with the RAM keyword.


       XIP the kernel from NOR and page select programs and modules from NOR into RAM, and use
    the remainder of RAM for file system, object store, and program memory.


    This configuration is very similar to the former configuration. However, for performance

    reasons it may be necessary to load specific programs and modules into RAM. Though the need

    for this will vary based on usage patterns, cache design and other factors, it is typically the

    case that executing code from SDRAM will be faster than from NOR flash memory. At CPU reset

    time, the Windows CE kernel is executed from NOR flash memory.


    To create an OS configuration of this type, once having created the previous configuration, the

    specific programs and modules to be run from SDRAM can be selected by marking each file in

    the .bib file(s) with a compressed flag. When Romimage.exe generates the final OS image,

    these files will be compressed, thus taking up less NOR flash memory, and at run time the OS

    loader will decompress the code and page it into RAM where it is executed.


       XIP everything from RAM and use NOR for code and data storage.
   This configuration makes the least use of the ability of NOR flash memory to support code that

   can be executed in place. However, it can offer the greatest overall performance solution for

   this specific memory topology. Instead of only compressing specific programs and modules in

   the image, as was done in the previous configuration, this configuration allows the entire OS

   image to be compressed. This configuration will typically require a monitor or boot loader to

   decompress and copy the entire image into RAM where it is executed.


   To create an OS configuration of this type, the platform's Config.bib MEMORY section should

   indicate the available RAM and for image storage with the RAMIMAGE keyword. The portion of

   RAM to be used for the file system, object store and program RAM should be denoted with the

   RAM keyword. Once Romimage.exe has created the final OS image, you can compress the

   image with any number of compression schemes. You then need to include code in any monitor

   or boot loader environment to decompress the image. This will load the image into RAM at boot

   time.


Summary



In this topology, the trade off for NOR flash memory versus RAM depends on the overall product

goals. The following items discuss some of the specific engineering trade-offs in this

design—hardware and/or software.


Performance issues


The performance target and the cost of DRAM determine whether code execution during CPU reset

continues from NOR flash memory. With DRAM access times typically shorter than NOR flash

memory, running out of RAM is often the way to realize greater performance. Code locality, cache

design, and memory bus design play a role in determining whether this holds true or not. A general

rule of thumb is to move the most heavily executed code into RAM. This could be the kernel itself

or specific modules. The kernel can be fixed to execute in place from RAM, start running in NOR

flash memory, and then copy itself into RAM during early initialization. If specific modules are

moved into RAM, the performance benefit of running from RAM while minimizing the NOR footprint

can be realized by compressing the modules of interest.


However, all of this takes away from one of the major benefits of NOR flash memory, which is the

ability to XIP from it. In some cases, due to cost, complexity or power consumption, executing in
place out of NOR with only a minimal amount of RAM is desirable. Specific optimizations can be

achieved by moving performance critical components into RAM.


Cost issues


There are a number of complexities in analyzing cost. At its most simplistic level, the cost of DRAM

is typically less than that of NOR flash memory. Therefore, minimizing the size of NOR flash

memory in favor of DRAM is typically advantageous both in terms of cost and performance.


Upgradeability


If upgradeability is a concern, this is not the best configuration to choose. First, the lack of a boot

loader means that the update would need to be done under the OS itself without the benefit of any

failsafe environment. A single OS image means that the entire image needs to be updated for any

one change. Because you would typically use NOR for executing in place, you need to be careful to

avoid reading from the part while it is being written.


Topology B: Linear ROM and RAM



In this configuration, non-writeable ROM, most likely production masked ROM, provides

non-volatile storage. The topology is very similar to topology A with the same design trade offs.

The main benefit of this design over topology A is typically the cost advantage, depending on

volumes, of replacing the NOR flash memory with a ROM part. The downside is effectively the lack

of a real software upgrade path for field devices other than physical replacement of the ROM part.

This topic only discusses the differences between this configuration and topology A because of their

similarities. For more information about topology A, see the Topology A: Linear (NOR) Flash

Memory and RAM topic.


OS configurations



For this memory topology, you can configure the Windows CE OS in the following ways:


       XIP everything from NOR and use RAM for file system, object store and program memory.

       XIP the kernel from NOR and page select programs and modules from NOR into RAM, and use
    the remainder of RAM for file system, object store and program memory.

       XIP everything from RAM and use NOR for code and data storage.
Summary



In this topology, the trade off for NOR flash memory versus RAM depends on the overall product

goals. The following items discuss some of the specific engineering trade-offs in this

design—hardware and/or software.


Performance issues


In general, the performance in this topology is similar to that of topology A with the same

performance trade-offs.


Cost issues


Mass produced ROMs are typically cheaper than the NOR solution per a given production volume

when large volumes of the same ROM and image are required. As such, you can reduce the cost by

running XIP out of ROM with a small amount of RAM.


Upgradeability


There is no upgrade path other than to replace the ROM.


Topology C: NAND Flash Memory and RAM



In this configuration, a single NAND flash memory device provides non-volatile storage. Because

NAND is a block device and does not support a linear interface, the CPU cannot directly execute

code stored in NAND flash memory. As a result, for this configuration to work, either a non-volatile

linear storage area is required—many hybrid NAND flash memory parts contain a small linear NOR

region called a boot block—or the NAND flash memory must appear to be linear, at least at boot

time. The basic idea is to have a small amount of code that runs at boot time, initializes the

hardware to the point that NAND flash memory and SDRAM are available, then moves the kernel

and some amount of the OS image from NAND to SDRAM where it is executed. From there, the OS

can page in the requisite modules from NAND flash memory as needed.


OS configurations



For this memory topology, you can configure the Windows CE OS in the following way:


       XIP everything from RAM and use NAND for code and data storage.
   This is the only viable configuration for a NAND and RAM design with little or no available linear

   non-volatile storage. The only real design issues are how much of the OS should be paged into

   RAM and when should the paging take place. For example, it is possible to compress the entire

   OS image in NAND flash memory and require the boot loader code to decompress an entire

   image into RAM. The disadvantages to this configuration include potentially greater RAM

   requirements for the design, greater power consumption, and greater load times as everything

   is moved into RAM. The advantages include faster code execution and smaller run-time loading

   delays.


   Alternately, with a multi-region design, it would be possible to split the kernel region from the

   other parts of the image, compress these parts, and then simply load only the kernel region

   into RAM at boot time. From there, the OS loader could then page in required modules from

   NAND flash memory as needed. The upsides could potentially be lower RAM requirements,

   power savings, and quicker load times. The downsides are potentially greater module load

   times and the need to manage multiple image regions.


Summary



While this topology does require some amount of linear non-volatile storage, it can provide cost

advantages when SDRAM prices are low. Performance is relatively good with code executing

primarily from SDRAM and allowing the OEM flexibility in deciding when code is paged into RAM.

The following items discuss some of the specific engineering trade-offs in this design—hardware

and/or software:


Performance issues


This topology yields good performance because code is executed from RAM. The primary design

trade-off is deciding how much of the code should be copied into RAM and when that copy should

occur. This decision is based on boot-time and run-time performance requirements. Unless the

overhead of decompressing code is an issue, all the code in NAND flash memory should be

compressed, thus saving flash memory space.


Power consumption in this configuration can be high as higher-powered SDRAM is required for the

solution. To minimize power consumption, improve control of RAM usage and power down banks

that are not required.
Also, the performance of write operations on NAND is typically better than NOR. As a result, by

running a flash file system on top of NAND, you can obtain the benefits of both the faster storage

device and larger storage capacity.


Cost issues


The amount of NAND flash memory required for a particular solution is smaller that other types of

non-volatile storage because typically everything in NAND flash memory is compressed. Given the

cost-per-byte advantage of NAND flash memory over other flash memory, compressing the image

usually means more flash memory is available for other purposes, for example, file system

storage.


Using this topology, which makes greater use of SDRAM than other configurations, means that the

cost is often more closely tied to SDRAM prices.


Upgradeability


If you can control OS paging, for example, by disabling an interrupt, you can upgrade NAND flash

memory images using an update application because all code needs to execute from SDRAM. To do

this, you need to shut down any applications or unload any drivers that may be dependent upon

the updated code. The safest way is to restart the system after an update.


One disadvantage to this configuration is the unavailability of a failsafe monitor or loader due to the

limited linear boot block region, which is typically only a few kilobytes. This means that any

problems during the field update of a device might not have a failsafe means of recovery. A solution

would be to store a second compressed OS for such occasions, but that would take up additional

NAND flash memory space.


By using the multi-region image option, you can achieve greater upgrade flexibility. You can

update specific regions individually with protection mechanisms unique to any or all of the regions.

In addition, the segmentation of the image can reduce the need to restart the system completely

following an upgrade.


Topology D: Linear ROM, NAND Flash Memory, and RAM
This topology differs from the topology C primarily in the amount of available linear memory, in this

case, ROM. For more information about topology C, see the Topology C: NAND Flash Memory and

RAM topic. While the boot block of a hybrid NAND flash memory part is usually a few kilobytes in

size, you can have a more complex monitor or boot loader environment with a suitably sized ROM

part, thus adding more options to any failsafe recovery. Combined with multi-region, it can also

mean greater protection and/or control over what can and cannot be updated on the system. For

example, the kernel image can be run or loaded in from ROM, thus it cannot be upgraded, but

applications can be paged in from NAND flash memory where they could be updated.


OS configurations



You can use the following OS configurations for this environment. The first configuration is the

most likely.


       XIP a monitor and/or boot loader from ROM, use NAND for all code and data storage, and use
    RAM for code execution and file system, object store and program memory.


    A simple failsafe loader stored in ROM allows you to boot strap the OS while providing a way to

    update the image in NAND flash memory if other means failed. The larger NAND flash memory

    capacities typically mean ample room for both image storage, possibly compressed and a

    separate file system partition for data storage. All OS code needs to be loaded or paged into

    RAM for execution.


       XIP everything from ROM, use NAND only for data storage and use RAM for file system, object
    store and program memory.


    From an upgrade scenario, this is a less flexible alternative than the previous configuration.

    However, it is possible to upgrade certain OS drivers and applications, which are stored in a file

    system on the NAND part. This imposes a small RAM footprint and thus can be less costly and

    save more power.


       XIP everything from RAM, use ROM for code storage, use NAND only for data storage, and use
    RAM for code execution and file system, object store and program memory.


    This is probably not a very desirable configuration. ROM costs are based on volumes and this

    configuration means fixing the image in ROM, which results in a weak upgrade path. This

    configuration also consumes more RAM than the previous configuration, thus more cost and
    power drain. However, this configuration can offer a performance benefit over the previous

    configuration.


       XIP the kernel from ROM, use NAND for code and data storage, and use RAM for code execution
    and file system, object store, and program memory.


    Given the need for ROM code to boot strap the OS, this configuration can be beneficial if you

    want to avoid kernel image updates in the field. Because most of the code resides in NAND

    flash memory, those parts could be field upgraded.


Summary



This topology allows for a number of different OS configurations. However, when using ROM parts,

analyze the volumes for cost savings and determine a clear field upgrade up front. Otherwise, you

may be locked into physical ROM upgrades in the field for any updates. You can save on power by

executing in place code from ROM instead of paging from flash memory, but that cost and

performance trade-off needs to be done against field upgradeability. Alternately, you can use NOR

flash memory in place of ROM to allow for better field upgradeability.


Performance issues


Running the image from DRAM yields the best performance. Depending on target power, cost, and

upgrade goals, running the image from DRAM can mean either running the whole image from

DRAM or running only parts of the image, such as the kernel and/or specific modules.


Power issues


Executing in place code directly from ROM yields the best power savings. This enables the basic

design to use less DRAM or enable parts of DRAM to be powered down when not required.


Cost issues


The ROM parts require larger volumes to amortize initial ROM mask design costs. However, this

can yield DRAM savings and power requirements.


Upgradeability
As much of the image as possible should reside in NAND flash memory for the best upgradeability.

This typically requires setting aside a reserved area in flash memory where OS components can be

paged in through a Windows CE-based file system like FAT file system. Updates then become only

a matter of downloading and replacing the file in the file system.


Topology E: Linear ROM, Disk Drive, and RAM



This memory topology is similar to topology D, where NAND flash memory is replaced by disk

storage. For more information about topology D, see the Topology D: Linear ROM, NAND Flash

Memory, and RAM topic. A major benefit of this configuration is the larger storage capacity

provided by the disk drive over solid-state non-volatile storage. The disadvantages include longer

access times and the inability to XIP directly from disk.


OS configurations



For this memory topology, you can configure the Windows CE OS in the following ways:


       XIP a monitor and/or boot loader from ROM, use disk for all code and data storage, and use RAM
    for code execution and file system, object store and program memory.

       XIP everything from ROM, use disk only for data storage and use RAM for file system, object
    store and program memory.

       XIP everything from RAM, use ROM for code storage, use disk only for data storage and use RAM
    for code execution and file system, object store and program memory.

       XIP kernel from ROM, use disk for code and data storage and use RAM for code execution and
    file system, object store and program memory.


Summary



This memory topology offers a multitude of different places from which an executable image can be

loaded or launched: RAM, ROM, or off a disk drive. RAM in general will provide the best

performance while ROM, based on volumes, will typically provide the best cost, and disk will

provide the best upgrade capabilities.


Performance issues


In general, you want code to execute out of RAM assuming ROM access time is slower than RAM.

Without a boot loader, the OS code that initially runs from ROM could copy itself entirely to RAM

and continue executing in RAM, or individual modules within the OS could be marked compressed
and thus be paged into RAM at run time. Similarly, any modules that you need to upgrade will need

to reside on a disk where they can be paged in through a file system and executed from RAM. Your

choice of file system has serious impact on performance and flexibility.


Generally, the most heavily executed code, which only needs to be loaded once, should reside on

disk. The cost per byte is lower and the possibility of upgrades exists. Meanwhile, any system

critical code or code that needs to be loaded and reloaded should reside in ROM. Whether the latter

is compressed, and thus paged into RAM, or whether it is XIP depends on two factors: the

frequency in which it is used, and the overhead involved in decompression and paging. Although

the kernel could copy itself from ROM to RAM, because it is a single OS image, that would

potentially waste a good amount of RAM and thus be undesirable from a cost perspective. In this

case, use of multi-XIP images can help.


Cost issues


Disk storage is the cheapest compared to ROM and RAM assuming the hardware is already present

for other design reasons. Otherwise, the cost of the hardware and the development effort involved

in getting it to work can be significant.


Upgradeability


For best upgradeability, as much of the image as possible should reside on disk. This will typically

require setting aside a reserved area on disk where OS components can be paged in through a

Windows CE-based file system, like the FAT file system. Updates then become only a matter of

downloading and replacing the file in the file system.




Conclusion

Your choice of storage device and the overall system memory topology in which it is used are

design decisions you should make with the following trade-offs in mind: performance, cost, power

consumption and field upgradeability. With a specific design goal in mind, the Windows CE .NET OS

and its associated development environment can provide you with a number of options along with

a path towards reaching your goals.
For More Information

For more information about the Windows CE .NET OS and a more detailed understanding of the

topics covered in this article, see Windows CE .NET Help or visit MSDN®, the Microsoft Developer

Network, at this Microsoft Web site.




Navigation


MSDN Library
Azure Services PlatformDesign ToolsDevelopment Tools and LanguagesMobile and Embedded
Development.NET DevelopmentOffice DevelopmentOpen SpecificationsServers and Enterprise
DevelopmentWeb DevelopmentWin32 and COM Development
Mobile and Embedded Development
Windows EmbeddedWindows MobileShared Windows Mobile 6 and Windows....NET Compact
FrameworkMobile Web DevelopmentWindows Automotive
Windows Embedded
Windows Embedded CEWindows Embedded NavReadyWindows Embedded StandardWindows NT
EmbeddedWindows Embedded for Point of Servi...The .NET Micro Framework Platform S...Server
Appliance KitColumns
Windows Embedded CE
Windows Embedded CE 6.0 Documentati...Windows Embedded CE 6.0 Technical A...Windows CE
5.0Windows CE .NETWindows CE 3.0Windows CE 2.1
Windows CE .NET
Product DocumentationTechnical Articles
Technical Articles
An In-Depth Look at the Power Manag...Application Development Landscape f...Application Modularity
Maximizes Po...Benchmarking Real-time Determinism ...Build Management Basics Using Micro...Building
and Testing Devices with t...Building DMA Drivers for the Window...Building Native C++ Applications
th...Building XML Web Services in Native...C# and Java: Comparing Programming ...Certificate
Enrollment in Windows C...Choosing a Windows Embedded API: Wi...Comparison of Windows CE .NET
4.2, ...Creating a Board Support Package Us...Critical Information about the Wind...Designing and
Optimizing Microsoft ...Developing Custom Controls in C# wi...Diagnosing Deadlock-Stall
Condition...Hardware-assisted Debugging with Pl...How Windows CE .NET is Designed
for...Implementing Fault Tolerant Systems...Implementing Rock-Solid Windows CE ...Interrupt
Architecture in Microsoft...Microsoft .NET Compact Framework fo...Native 802.11 Support in Windows
CE...Performance Test Methodologies for ...Power Management Features of Window...Predefined
Configurations in Window...Providing Features and Multiple Pro...Real-Time Behavior of the .NET
Comp...Security Features in Windows CE .NE...Stress Testing: Using Modular Stres...System Memory
Management in Windows...Testing NDIS Miniport Drivers by Us...Tips and Tricks for Testing
Windows...UDDI Inquiry with Windows CE .NETVoice over IP (VoIP) Phone SecurityWindows Media
Overview and Optimiza...Windows CE .NET Advanced Memory Man...Windows CE .NET and the
Extensible ...Windows CE .NET Driver DevelopmentWindows CE .NET Interprocess Commun...Windows
CE .NET Long-Haul Testing S...Windows CE .NET Technical Frequentl...Writing Reliable Native Code
System Memory Management in Windows...

				
DOCUMENT INFO