part1 by nuhman10


									ENCH 617 – Advanced Production Operations –
Midterm Exam, November 1, 2006

Student ID #_________________________
Duration – 90 minutes
Closed book, closed notes, regular mathematical calculators only


Multiple Choice – 25 x 2 marks each = 50 possible Marks ______________

Short Answer – 20 possible marks                                  _______________

Computational – 30 possible marks                                 _______________

(Bonus question 3 marks – optional)


   1. A fluid system whose apparent viscosity decreases as shear rate increases is
      known as a;
          a. Newtonian Fluid
          b. Thixotropic Fluid
          c. Rheopectic Fluid
          d. Bingham Plastic Fluid

   2. The Gas Formation Volume Factor ‘Bg' can be defined as;
         a. The volume of a unit volume gas at standard conditions of temperature
            and pressure
         b. The volume a unit volume of gas at reservoir conditions of temperature
            and pressure
       c. The ratio of the volume of a given amount of gas at standard temperature
          and pressure divided by the volume of the same amount of gas at reservoir
          temperature and pressure.
       d. The ratio of the volume of a given amount of gas at reservoir temperature
          and pressure divided by the volume of the same amount of gas at standard
          temperature and pressure.
       e. None of the above.

3. For a reservoir consisting of 100 m of total thickness, of which 20 m of this
   thickness consist of permeable reservoir sand, the net to gross pay ratio would be
   defined as;
       a. 20%
       b. 80%
       c. 1 part in 5
       d. 4 parts in 5
       e. None of the above

4. Which of the following formation types has the highest grain density?
     a. Sandstone
     b. Limestone
     c. Dolomite

5. Which of the following is NOT a type of drilling bit commonly used in the
      a. Percussion/air hammer
      b. PDC
      c. Orthosilicate crystal
      d. Diamond Roller Cone

6. The ‘flexibility’ of an immiscible interface is controlled by the;
      a. Density difference between the two fluids
      b. Viscosity ratio between the two fluids
      c. Interfacial tension between the two fluids
      d. Solids content of each fluid
      e. None of the above

7. Given the following air water system in which a water wet glass capillary tube is
   inserted and in which capillary rise of water occurs as shown, the following
   statement would be most correct;


       a. The pressure at point B in the gas outside the capillary tube and at point A
          in the water inside the capillary tube is the same.
       b. The pressure at point B is higher than at point A
       c. The figure is drawn incorrectly for a water wet capillary
       d. The pressure at point A is lower than the pressure at point B
       e. None of the above

8. Which of the following factors does not impact the specific capillary pressure at a
   given fluid saturation level?
       a. Wettability
       b. Pore Geometry
       c. Surface curvature of the interface between the two fluids
       d. Interfacial tension
       e. Fluid density

9. The main disadvantage of the bulk porous method for capillary pressure
   determination is;
       a. Only one sample can be run at a time
       b. Very slow for low permeability samples
       c. Can only run with gas and water
       d. None of the above
       e. All of the above

10. A sample with a USBM wettability index of -0.70, Amott water index of 0.3 and
    Amott oil index of 0.6 would likely be classified as;
       a. Neutral Wet
       b. Water Wet
       c. Oil Wet
       d. Mixed wet
       e. None of the above

11. In a perfectly neutral well rock the height of the water-oil transition zone would
        a. Large
        b. Small
        c. Zero
        d. Infinite
12. A zero transition zone height would be obtained in a water-oil system if;
       a. The rock was perfectly neutral wet
       b. The capillary pressure value was zero
       c. The IFT was zero
       d. All of a to c
       e. None of the above

13. Micropores represent pores connected by pore throats of diameter of less than
       a. 0.5 microns
       b. 1 micron
       c. 2 microns
       d. 3 microns
       e. 5 microns
       f. 10 microns

14. Hysteresis effects in capillary pressure and relative permeability are believed to
    be directly attributable to differences in advancing and receding contact angle
    which are believed to be a function of;
        a. Surface roughness
        b. Surface wettability
        c. Boundary layer thickness
        d. Shear rate
        e. Interfacial tension
        f. None of the above

15. If we had a old set of relative permeability data where the Kro value at 20% initial
    water saturation had a value of 0.793, and the endpoint Krw value had a value of
    0.224. If we converted the data to a ‘normalized’ relative permeability
    representation basis, what would the value of the Krw be in the normalized set of
        a. 1.0000
        b. 0.2824
        c. 0.1776
        d. 0.2070
        e. None of the above

16. Which one of these statements is correct concerning the value of the critical water
        a. It is always less than the initial water saturation
        b. It is always equal to the initial water saturation
        c. It is always more than the initial water saturation
        d. It can be less than, equal to or greater than the initial water saturation
        e. None of the above
17. When flowing perpendicular to bedding planes in contrast to flowing parallel to
    bedding plans the relative permeability values are generally;
       a. Higher
       b. Lower
       c. The same

18. In a clean state, carbonate rock surfaces are generally;
        a. Strongly oil wet
        b. Strongly water wet
        c. Mixed wet
        d. Neutral wet

19. At a constant level of interfacial tension and mobility ratio the ultimate residual
    oil saturation would likely be the lowest in;
        a. Strongly water wet rock
        b. Strongly oil wet rock
        c. Neutral wet rock

20. In a vaporizing gas miscibility process the low IFT condition is predominantly
        a. On the trailing edge of the displacement bank by extraction of
            intermediate components from the injection gas phase.
        b. Immediately upon contact with the oil
        c. On the leading edge of the displacement bank by the extraction of
            intermediate components from the oil phase
        d. None of the above

21. In a rich gas condensate reservoir with a critical condensate saturation of 22% and
    a maximum liquid dropout of 15% at the final depletion pressure level a major
    concern would be;
        a. Formation damage effects due to condensate dropout and trapping around
            the production wellbores.
        b. Loss of a large portion of the rich liquid phase due to capillary trapping
            effects in the reservoir
        c. Condensate loading and killing of the wells during later production in the
            life of the well
        d. All of the above
        e. None of a to d

22. The steady state method of measuring relative permeability is not used commonly
    for reservoir condition testing due to;
        a. Extensive computations are required to generate the relative permeability
        b. The process in inherently unstable
        c. The process is very slow and time consuming
        d. All of the above
   23. Fines migration when injecting water is more of a potential issue in;
          a. Water wet reservoirs
          b. Mixed wet reservoir
          c. Oil wet reservoirs
          d. Neutral wet reservoir
          e. Not impacted by wettability

   24. A negative skin factor can be equated on a flow basis to a;
          a. Larger wellbore radius
          b. Smaller wellbore radius
          c. Zone of reduced permeability surrounding the well
          d. Barriers to oil flow that selectively reduce its permeability more than
              water flow
          e. None of the above

   25. The most common damaging clays that contribute to fines migration problems
            a. Smectite and Illite
            b. Chlorite and Illite
            c. Illite and mixed layer clay
            d. Chlorite an kaolinite
            e. Illite and kaolinite
            f. None of the above

   1. Give four of the most important functions that a typical overbalanced drilling mud
      performs? (4 Marks)
2. Name 10 factors that are known to impact the configuration and the endpoints of
   relative permeability curves (10 marks).
       a. _________________________________________________
       b. _________________________________________________
       c. _________________________________________________
       d. _________________________________________________
       e. _________________________________________________
       f. _________________________________________________
       g. _________________________________________________
       h. _________________________________________________
       i. _________________________________________________
       j. _________________________________________________

3. Draw comparative sets of relative permeability curves for the following three
   wettability types (6 Marks);
   1. Given the following relationship for computation of bottomhole pressure;

                Pcirc  gh  L fp Ff  BPR
Consider the following wellbore;

Standpipe Inj

                                Return Annulus


                             Drill String

                              Mud Motor


Hole Diameter – 200 mm
Drill string OD – 160 mm
Drill string ID – 140 mm
Mud average density (assume incompressible fluid ) = 1130 kg/m3
Pump Rate – 1400 liters (1.4 m3) per minute of drilling fluid (assume overbalanced and
no inflow from the formation)
Well orientation – perfectly vertical
Interior drill string friction factor component (in kPa per meter of flow path) = 0.35 x
mud average velocity in m/s
Exterior Annular Section friction Factor component (in kPa per meter of flow path) =
0.42 x mud average velocity in m/s
Pressure in the formation next to the wellbore at the bit – 20000 kPa
True vertical depth from the surface to the base of the wellbore – 2345 m
Pressure drop across mud motor (in kPa) – 2214.6 x mud volumetric flow rate in
Assuming that the surface backpressure on the system at the choke manifold (Point ‘C”)
is being maintained at a constant value of 800 kPag, what is the effective circulating
bottomhole pressure at the base of the wellbore at point ‘B’ and what is the mud pump
injection pressure into the standpipe at surface at point ‘A’ to maintain the given
circulation rates? – Show all calculations and remember to include all appropriate
friction effects (with proper sign – remember why fluids flow and how friction works),
hydrostatic and backpressure effects. (20 Marks).
2. Given the following data table and plot from a conventional combined
   Amott/USBM test, estimate from the given curves and provided saturations (use
   rough integration only) the;
      a. The approximate USBM wettability index (USBM index = log10 (A1/A2)
      b. The Amott water index (Vol spontaneous water suction/total
      c. The Amott oil index (Vol spontaneous oil suction vs. total oil
      d. What would you conclude about the wettability if this reservoir based on
          this data (total – 10 Marks)

                                 Combined Ammot/USBM Wettability Test Results



Capillary Pressure - kPa

                                                                               Water Ssturation
                                                                               Oil Saturation



                                 0   0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9   1
                                         Water Saturation - Fraction
Pcap         Sw              Pcap        Sw
kPa                          kPa
         0    0.125                  0        0.71
         0    0.125                  0         0.6
        -5     0.13                  5         0.4
       -10     0.14                 10        0.32
       -20     0.18                 20        0.28
       -30     0.35                 30        0.21
       -40     0.45                 40        0.16
       -50     0.65                 50        0.15
       -60       0.7                60        0.14
       -70     0.71                 70        0.13
(note – the two zero capillary pressure values represent the water saturation at the
beginning and the end of the static fluid exposure phase of the combined Amott/USBM
wettability test)

A man is in a small boat in a lake fishing. He rows to the middle of the lake and throws a
100 kg iron anchor overboard to hold the boat in place. Does the level of the water in the
lake go up, down or stay the same – explain your answer clearly for full marks – no
marks for lucky guesses.

To top