TANDEM BOX DRAWER

Document Sample
TANDEM BOX DRAWER Powered By Docstoc
					TANDEM BOX DRAWER
1. The positions for fixing the runners with                                                   2. Slide the base panel into the groove on the metal            3.        Push the plastic lug into the side until it locks.
    integrated blu-motion, to the Base end panel                                                     side, and fix using two K screws as shown below.                    Repeat for the remaining plastic lug. Secure the
    are shown here. Use:                                                                                                                                                 back panel using four J screws.
    Position 1 for Drawer Line units
    Positions 1, 3 and 5 for 3 Drawer Packs
    Positions 1,2,3 and 5 for 4 Drawer Packs.                                                                                                                                                         BACK
    All 5 Positions for 5 Drawer Packs
    Repeat for the opposite end panel (right hand                                                                                 BASE           DE
    end is shown).                                                                                                                             SI

                                                                                                                                                                                                     BASE
           1


           2
               2*                                                                                 4. Slide opposite side onto base panel and fix as            5. It may be necessary to drill additional holes on the fascia
           3                                                                                             shown. If assembling a deep drawer, fix the gallery        panel to take the Drawer Front fixing clips (and Gallery
                                                                                                         rails to the hob drawer front PRIOR to attaching to        Rails if assembling a 283mm Hob Drawer). The
                                                                                                         the drawer box.                                            necessary dimensions are shown below.
           4
                                                                                                                                                                                                                            500mm deep
                                                                                                                                                                                       10mm dia x 12mm deep
           5




                                                                                                                                                                    64
                                                                                                                                                                                     only on 283mm Hob Drawers
                                                                                                                                                                                                                            450mm deep
                                                                                                                                             BACK
                                                                                                                         DE
                                                                                                                       SI




                                                                                                                                                                    64
    NOTE: For a 2 Drawer Pack use Positions 2* and 5.
                                                                                                                                                                                       2.5mm dia x 3mm deep




                                                                                                                                                                    32
    NOTE: Positions 2*, 3 and 5 have a third hole to provide
    extra support for a 500mm depth drawer.




                                                                                                                                                                    65
                                                                                                                                     BASE




                                                                                                                                                                                                                             34
    NOTE: If you are assembling a 1000 Pan Drawer, it is
    necessary to put the centre drawer support in the LOWER                                                                                                              32
                                                                                                                                                                                     5mm dia x 12mm deep only on
    position whilst assembling the cabinet.
                                                                                                                                                                                   283mm Hob Drawer 1000mm wide
    NOTE: The fittings position for the back panel are for a
                                                                                                                                                                           equal                     288            equal
    500mm depth unit. These should be moved in if assembling
    a 450mm depth drawer unit.
                                                                                                                                                               6. To adjust the drawer front once it has been fitted to
                                             FITTINGS SUPPLIED
                                                        PAN DWR                                                                    PAN DWR
                                                                                                                                                                    the drawer box, use the adjustment screws as
                                   300-600   800-1000                                                        300-600   800-1000
                                                        800-1000                                                                  800-1000                          shown below.
A              Metal
               Dowel                           2          4        M                        Euroscrew
                                                                                            6 x 11mm           6            6       12                                                Drawer front
                                                                                                                                                                                        removal
B               Metal
                Cam                            2          4        N                     Round Head Screw
                                                                                            6 x 5/8mm          4            4        8                                 Side                              Height
                                                                                                                                                                    adjustment                         adjustment
G              Countersunk Screw
                   8 x 1 1/4"                  2          4        S                          Door
                                                                                            Buffer Pad        1pair     1pair      2pairs
J           Countersunk Screw
                 6 x 1/2”            6         6         12        V   CRO
                                                                       IMP    WN
                                                                             ERI
                                                                                   AL
                                                                                        Crown Conceal Caps     2            2        4
K           Flange Head Screw
                 6 x 5/8"            6         6         12                                                                                                                                                           November 2007

				
DOCUMENT INFO
Shared By:
Categories:
Stats:
views:535
posted:5/23/2011
language:English
pages:1