OPERATIONAL MENU FLOW CHART SYSTEM MENU FLOW CHART SYSTEM

OPERATIONAL MENU FLOW CHART SYSTEM MENU FLOW CHART SYSTEM MENU FLOW CHART (cont) SENSOR TUNE This procedure calibrates all optical sensors to the ambient light source. Use this procedure if paper does not load properly or experiencing top of form problems. This procedure MUST be performed without paper installed. 1. Press and keys as you apply power to the printer. Press <↑> key until ... Press key. Press <↑> key. Press key. Press key. Ê FONT STYLE Ë Courier Ë Gothic Ë Prestige (8) Ë Script (8) Ë Orator (8) Ë OCRB-EXT Ë OCRA-EXT Ë Draft Ê CHARS PER INCH Ë5 Ë6 Ë 7.5 Ë 8.5 Ë 10 Ë 12 Ë 15 Ë 17.1 Ë 20 Ë 24 (8) Ê PAGE SETUP Ë Top Reference Ì -72/72 - 144/72 (6/7) Ì -90/90 - 180/90 (8) Ë Lines/ Inch Ì2 Ì3 Ì4 Ì6 Ì8 Ì 12 Ë Form Length Ì 1 thru 144 Ì A5 Ì A4 Ì A3 Ì A2 Ë Top Margin Ì 0 thru 12 Ë Bottom Margin Ì 0 thru 12 Ê LINE SETUP Ë Left Margin Ì 0 thru 135 Ë Right Margin Ì 1 thru 136 Ë Left Reference Ì 0/120 thru 60/120 Ê PRINT MODES Ë Bold Ë Underline Ë Fwidth UL Ë Double HI Ë Overscore Ë Proportional (8) = 3480 printers only (7) = 3470 printers only (6) = 3460 printers only Ê SPECIAL MODES Ë Impact Mode Ì Medium Ì High Ì Low Ë Quiet Mode Ë Reduce Slew Ë Labels Ë Text Direction Ì BI Ì UNI Ë Graph Direction Ì BI Ì UNI Ê FORM THICKNESS Ë Auto Ì -5 thru 3 Ë Fixed Ì 0.6 thru 9.3 Ë Manual Ê EMULATION Ë Epson LQ (8) Ë IBM XL24e (8) Ë 1220ANSI (8) Ë Epson FX (6/7) Ë IBMXL3 (6/7) Ë 3410ANSI (6/7) Ë 3840ANSI (6/7) Ë 3460ANSI (6) Ë 3470ANSI (7) Ê SAVE TO FORMAT Ë None Ë Form #1 Ë Form #2 Ë Form #3 Ë Form #4 Ê PRINT STATUS Ë Config Ë Formats Ë System Ê CLEAR BUFFER Ê TEST MODE Ë Paper Width Ì 80 Ì 136 Ë Start Test Ë Hex Dump Ê SELECT FORMAT Ë Form #1 Ë Form #2 Ë Form #3 Ë Form #4 Ê = 1st menu level Ë = 2nd menu level Ì = 3rd menu level These menu flow charts reflect a 3480, 3470 and 3460 at Initialized:Dom settings. Variations of this menu may occur if alternate operational or system menu options are chosen. Ê CHARACTER SET Ë Epson Ì Italic Ì CS1 Ì CS2 Ë IBM Ì CS1 Ì CS2 Ë ANSI Ì CS1 Ì CS2 Ê NATIONAL SET Ë Epson Ì (25 countries) Ë ANSI Ì (23 countries) Ê CHARACTER TABLE Ë Epson Ì (28 code tables) Ë IBM Ì (28 code tables) Ë ANSI Ì (28 code tables) Ê LCD LANGUAGE Ë English Ë Francais Ë Deutsch Ë Italiano Ë Espanol Ê IBM OPTIONS Ë Comp Chr Ì 15 (7) Ì 17 Ì 20 Ì 24 (8) Ë Auto CR Ë AGM Mode (8) Ê ANSI OPTIONS Ë RIS Enable Ë SI / SO CTL Ë Auto CR Ë Prime On DEL Ë Control In DG Ë Expand Up Ë ALT Graphics (8) Ë 8 Bit CTRL Ë ENQ Code Ì No Ì1 Ì2 Ë S / Sub Script Ë ESC + CTRL Code Ë VT Not Set Ë Fixed Fonts (6/7) Ê OTHER OPTIONS Ë Auto LF Ë Double LF Ë Auto Wrap Ë Auto Tear Ë Retract Time Ì 1 thru 99 Ë Confirm Park Ë Paper Overlay Ë Interlock Ë Move Paper (7) Ì 0 thru 22 Ë NVRam Save Ë Clear Margin Ë 2 Box Option Ë CAN Code Ë Backup Ì None Ì BC Ì OS Ì Both Ë Guard Bar Ë Postnet Comp Ë Slash Zero Ë Bell Enable Ë Epson OGM (8) Ë Native Command Ë Online Default Ì OFLN Ì ONLN Ì PRIO Ë Online At Load Ë Ribbon Type Ì Black Ì Process Ì Red / Black Ë Gap Assign Ì Path Ì Format Ê BUFFER SETUP Ë Download Ë Buffer Size Ì 256 thru 32K (6/8) Ì 256 thru 64K (7) Ë High Trip Ì 91% thru 99% Ë Low Trip Ì 1% thru 94% Ê INTERFACE Ë Typel Ì Parallel Ì Serial Ì Both Ë Switch Time Ì 5 thru 99 seconds Ê PARALLEL OPTIONS Ë AFXT Ë SLCT-IN Ë RCV DC1 / DC3 Ë INIT Enable Ë Fault Lead Ì None Ì ONLN Ì Fault Ë ACK Timing Ì Before Ì After Ì During Ë STRB Polarity Ë FLT Polarity Ë SLCT Polarity Ë PE Polarity Ê SERIAL OPTIONS Ë Baud Rate Ì 300 Ì 600 Ì 1200 Ì 2400 Ì 4800 Ì 9600 Ì 19200 Ì 38400 Ë Data Bits Ì8 Ì7 Ë Parity Type Ì None Ì Odd Ì Even Ì Mark Ì Space Ë ETX / ACK Ë Robust XON Ë XON / XOFF Status Ì ON / BU Ì FA / BU Ì None Ì ONLN Ì Buff Ì Fault Ë DTR Status Ì ON / BU Ì FA / BU Ì None Ì ONLN Ì Buff Ì Fault Ë RTS Status Ì ON / BU Ì FA / BU Ì None Ì ONLN Ì Buff Ì Fault Ë SRTS Status Ì ON / BU Ì FA / BU Ì None Ì ONLN Ì Buff Ì Fault Ë DTR Polarity Ë RTS Polarity Ë SRTS Polarity Ê KEY LOCKOUT Ë (Lists All Keys) Ê PATH OPTIONS Ë Tractor Ì Push Ì Pull Ì Pshpl Ë ASF Type Ì None Ì 1 Bin Ì 2 Bin Ì 3 Bin Ê PATH / FORMAT Ë Rear Ì Current Ì Format #1 Ì Format #2 Ì Format #3 Ì Format #4 Ë Front Ì Current Ì Format #1 Ì Format #2 Ì Format #3 Ì Format #4 Ë Manual Ì Current Ì Format #1 Ì Format #2 Ì Format #3 Ì Format #4 Ê PROGRAM UNITS Ë Fixed Ë Numeric Ê PRINT STATUS Ë Config Ë Formats Ë System 2. 3. 4. 5. 6. LCD = “Starting Up” LCD = “Initial Menu” LCD = “Initialize” LCD = “Sensor Tune” LCD = “Tune> N” LCD = ”Tune: Y” LCD = “Sensors Tuning“ LCD = “Initialize” LCD = “ “ LCD = “Paper Out: xxx” INITIALIZATION Use this procedure if experiencing abnormal operation, unusual control panel operation, or when new firmware is installed. 1. Press and keys as you apply power to the printer. Press key. Press <↑> key until ... Press key. Press key. 2. 3. 4. 5. LCD = “Starting Up” LCD = “Initial Menu” LCD = “Initialize” LCD = “Init> No” LCD = “Init: Dom” or LCD = “Init: Int” LCD = ”Initializing” LCD = “Alignment” LCD = “ “ LCD = “Paper Out: xxx” (Use DOM for USA defaults. Use INT for International defaults.) CONFIG / FORMAT / SYSTEM PRINT Use this procedure to get a printed report of the configuration of your printer. The “PRINT: SYSTEM” selection will display your printer’s firmware and font levels. 1. 2. 3. 4. 5. 6. Press key. Press key. Press <↑> key until ... Press key. Press <↑> key until ... Press key. On Line LED goes out. LCD = "Operational Menu" LCD = "Font Style" LCD = "Print Status" LCD = "Print> Config" LCD = "Print: Config" or LCD = “Print: Formats” or LCD = “Print: System” Desired printout begins. SELF TEST PRINTING 1. 2. 3. 4. 5. 6. 7. 8. 9. Press key. Press key. On Line LED goes out. LCD = "Operational Menu" LCD = "Font Style" Press <↑> key until ... LCD = "Test Mode" Press key. LCD = "Test:Paper Width" Press <↑> key until ... LCD = "Test:Start Test" Press key. LCD = “Test:Start> N” Press <↑> key. LCD = ”Test:Start: Y” Press key. LCD = “Test Mode” Self test begins. Press key to end test. MENU NOTES Enter the SYSTEM MENU by holding down on the key as you apply power to the printer. FRONT PUSH PATH Paper Exit FRONT PUSH/PULL PATH Rear Feed Pull Paper Exit OPTIONS & ACCESSORIES Ribbon (Standard) Color Ribbon (Process) Color Ribbon (Red / Black) Color Ribbon (Black) Color Kit (60/80) 1A3000B01 1A3000B02 1A3000B03 1A3000B04 1A3003B04 1A3003B01 1A3003B02 GEK-89171 GEK-89173 GEK-89172 GEK-89242 GEK-89243 1A3003B05 1A3003B06 3A1213B01 3A1213B05 3A1213B06 1A3003B03 1A3003B08 Front Feed Push 1. 2. 3. 4 5. Close the paper bail located under the top cover. In the SYSTEM MENU set Path Options / Tractor to “Push”. Install the tractor in the “Front Feed” position. Select the front path LED on the control panel. Correctly install paper in the front tractor and press the key to load paper to top of form. Front Feed Push 1. 2. 3. 4. 5. Verify push/pull slide is in the “pull” position. Open the paper bail located under the top cover. In the SYSTEM MENU set Path Options / Tractor to “Pshpl”. Install one tractor in the “Front Feed” position. Install the second tractor in the “Rear Feed” position. Press down on the levers on the rear of the tractor unit and tilt the tractor unit back at an angle as shown above. Select the front & rear path LEDs on the control panel. Correctly install paper in the front tractor and press the key. Paper will advance far enough to install in the rear tractors. Install paper in the rear tractors. Manually turn the square shaft to align the paper holes with the tractor pins. Verify there is no slack in the paper. Place printer On Line to engage rear tractors. Single Bin Feeder Extension Module Manual / Service (60/80) Manual / Service (70) Manual / Users/Prog (70) Manual / Users/Prog (60) Manual / Users/Prog (80) Pedestal (Tilt) Pedestal (Non-Tilt) Pedestal (Universal) Paper Catch Tray (Univ Ped) Forms Rack (Univ Ped) Tractor Assembly (60/80) Tractor Assembly (70) Use the front push path: • • • For general purpose continuous forms applications. When using multipart forms, labels, or heavy stock which requires a straight through paper path. When using the 2-box option. This path can serve as your secondary paper source when your primary source (rear path) runs out of paper. When your work area makes using the front path more convenient. 6 7. 8. • 9. Use the front push/pull path: • When using multipart forms, labels, or heavy stock which requires a straight through paper path. When printing applications require extremely precise paper handling. HOW TO CONTACT GENICOM U.S.A. GENICOM USA..................... 800-436-4266 BBS ....................................... 540-949-1576 Technical Support.................. 540-949-1031 GENICOM Web Site.............. http://www.genicom.com Printer Sales................................telemarketing@genicom.com Supplies.......................................supplies@genicom.com Technical Support.......................techsupport@genicom.com Service Training..........................essctrain@essc.com REAR PUSH PATH Paper Exit Rear Feed Push • CUT SHEET PATH Paper Exit Cut Sheet Feed INTERNATIONAL Product Sales ........................ info@genicom-intl.com Australia................................. 61-2-9417-6411 Belguim.................................. 32-2-712-6270 Canada .................................. 800-268-0464 Canada Web Site .................. http://www.genicom.ca Denmark ................................ 45-45-421120 France ................................... 33-1-69-542-317 Germany................................ 49-6196-65990 Hong Kong............................. 852-2805-3601 Italy ........................................ 39-2-253041 Italy Web Site ........................ http://www.genicom.it Singapore .............................. 65-28-64240 Spain...................................... 34-1-351-48-99 Sweden.................................. 46-31-876-500 United Kingdom ..................... 44-1252-744400 1. 2. 3. 4. 5 6. Verify push/pull lever is in the “push” position. Close the paper bail located under the top cover. In the SYSTEM MENU set Path Options / Tractor to “Push”. Install the tractor in the “Rear Feed” position. Select the rear path LED on the control panel. Correctly install paper in the rear tractor and press the key to load paper to top of form. 1. 2. 3. 4. 5. 6. Use the rear push path: • • • For general purpose continuous forms applications. When using 1 to 4 part forms. When using the 2-box option. This path can serve as your secondary paper source when your primary source (front path) runs out of paper. When your work area makes using the rear path more convenient. Open the cut sheet support cover by pushing downward. Adjust the left and right paper guides for the size of the cut sheet to be used. Close the paper bail located under the top cover. Select the cut sheet LED on the control panel. Insert the sheet between the guides and into the printer. The feed rollers will pull the paper to top of form. A cut sheet may be inserted while continuous forms are presently loaded. When this occurs the paper in the current path will park and the cut sheet will be loaded. •••••••••• • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • •••••••••••••••••••••• • • • • • • • • • • Pocket User Guide Serial Matrix Printers GENICOM GEK-89273 • Use the cut sheet path: • For cut sheet applications and form set printing. (06/98) (Rev 018)