ANTI-THEFT FUEL DEVICE ASSEMBLY INSTRUCTIONS

Document Sample
ANTI-THEFT FUEL DEVICE ASSEMBLY INSTRUCTIONS Powered By Docstoc
					ANTI-THEFT FUEL DEVICE
ASSEMBLY INSTRUCTIONS
Please scroll down to the fitting instructions you require.




IMEX00001 MERCEDES, VOLVO (with aluminium tanks),
MAN, DAF (not 45s), IVECO, RENAULT (Premium), FODEN,
SEDDON, ERF ECT/ECX, SCANIA 3 Series                          2

IMEX00001A SCANIA 4 Series                                    3

IMEX00001B MERCEDES ATEGO (80mm) Plastic tank                 4

IMEX00001C Earlier SCANIA, VOLVO (with Steel tanks
- except FL6), ERF ECT, SCANIA 3 Series, Agricultural/
Construction                                                  5

IMEX00001E IVECO EUROCARGO - 04 >                             6
ANTI-THEFT FUEL DEVICE
ASSEMBLY INSTRUCTIONS
MERCEDES, VOLVO (with aluminium tanks), MAN, DAF (not 45s), IVECO,
RENAULT (Premium), FODEN, SEDDON, ERF ECT/ECX, SCANIA 3 Series

Bayonet Fixing Caps
Fitting Kit Incorporates: 2 rivets, 1 spacer and a 4.2mm Drill Bit
1. Ensure the surface is clean.

2. Screw the anti theft device onto the filler neck until it reaches the stops.

3. Inside the Anti-Theft Fuel Device you will find 2 pre-drilled holes for fixing. Mark the position of the 2 holes
onto the filler neck for drilling.

4. Unscrew and remove the Anti-Theft Fuel Device.

5. Drill out the 2 marked holes on the filler neck using the 4.2mm drill bit provided, taking care that none of
the drilled material falls into the tank, a magnet or vacuum can be used whilst drilling to prevent this.

6. Screw on the Anti-Theft Fuel Device until the 2 holes line up with one another, then using a small pry bar
adjust the 2 lugs on the underside of the device to remove any play providing a good seal.

7. Fix in place using the 2 rivets provided with the tail end of the rivet uppermost using the spacer provided to
gain access with the rivet gun, take care to ensure the tail of the rivet or the spacer does not fall into the tank.

We accept no responsibility for damage resulting from incorrect installation. We recommend that installation be carried out by a
                                                                                                                                       IMEX00001
qualified engineer. Drilling residue etc. remaining in the tank can lead to the destruction of the pump and / or filter.           V5. 03/03/2008
ANTI-THEFT FUEL DEVICE
ASSEMBLY INSTRUCTIONS
SCANIA 4 Series

Screw Fixing Caps
1. Ensure the surface is clean.

2. Ensure the tank is filled but no more than half full.

3. Screw the Anti-Theft Fuel Device onto the filler neck as tight as possible.

4. Insert the 2 provided self tapping screws into the 2 pre-drilled holes and screw up to the mark, between
the thread of the Anti-Theft Fuel Device and the Scania filler device.

5. To make sure that the screws cannot be removed simply drill out the cross head of the screw so that they
cannot be unscrewed.

6. Afterwards unscrew and remove the dipstick out of the fuel gauge and move the indicator 10cm towards
the drivers cab. This will ensure that the float will remain free and not catch on the Anti-Theft Fuel Device,
giving a false fuel level reading.

7 . Replace the modified dipstick and screw firmly back into place.

8. If the existing cap is a screw fixing this will need replacing by a bayonet fixing cap (IMEX00002)


We accept no responsibility for damage resulting from incorrect installation. We recommend that installation be carried out by a
                                                                                                                                     IMEX00001A
qualified engineer. Drilling residue etc. remaining in the tank can lead to the destruction of the pump and / or filter.           V5. 03/03/2008
ANTI-THEFT FUEL DEVICE
ASSEMBLY INSTRUCTIONS
MERCEDES ATEGO
Fitting Kit Incorporates: 2 rivets, 1 spacer and a 4.2mm Drill Bit

1. Ensure the surface is clean.

2. Screw the Anti-Theft Fuel Device onto the filler neck until it reaches the stops.

3. Inside the Anti-Theft Fuel Device you will find 2 pre-drilled holes for fixing. Mark the position of the 2 holes
onto the filler neck for drilling.

4. Unscrew and remove the Anti-Theft Fuel Device.

5. Drill out the 2 marked holes on the filler neck using the 4.2mm drill bit provided, taking care that none of
the drilled material falls into the tank, a magnet or vacuum can be used whilst drilling to prevent this.

6. Place the Anti-Theft Fuel Device back on the filler neck and line up the holes for fixing.

7. Fix in place using the 2 rivets provided with the tail end of the rivet uppermost using the spacer provided
to gain access with the rivet gun, take care to ensure the tail of the rivet or the spacer does not fall into the
tank.




We accept no responsibility for damage resulting from incorrect installation. We recommend that installation be carried out by a
                                                                                                                                     IMEX00001B
qualified engineer. Drilling residue etc. remaining in the tank can lead to the destruction of the pump and / or filter.           V5. 03/03/2008
ANTI-THEFT FUEL DEVICE
ASSEMBLY INSTRUCTIONS
Earlier SCANIA, VOLVO (with Steel tanks - except FL6), ERF ECT, SCANIA 3
Series, Agricultural/Construction
Fitting Kit Incorporates: 2 rivets, 1 Rivet Gun and a 4.2mm Drill Bit

1. Ensure the surface is clean.

2. Offer the Anti-Theft Fuel Device onto the filler neck in the correct position - like a bayonet cap.

3. Inside the anti theft device you will find 2 pre-drilled holes for fixing. Mark the position of the 2 holes onto
the filler neck for drilling.

4. Unscrew and remove the Anti-Theft Fuel Device.

5. Drill out the 2 marked holes on the filler neck using the 4.2mm drill bit provided, taking care that none of
the drilled material falls into the tank, a magnet or vacuum can be used whilst drilling to prevent this.

6. Place the Anti-Theft Fuel Device back on the filler neck and line up holes for fixing.
7. Fix in place using the 2 rivets provided with the tail end of the rivet uppermost using the spacer provided
to gain access with the rivet gun, take care to ensure the tail of the rivet or the spacer does not fall into the
tank.


We accept no responsibility for damage resulting from incorrect installation. We recommend that installation be carried out by a
                                                                                                                                     IMEX00001C
qualified engineer. Drilling residue etc. remaining in the tank can lead to the destruction of the pump and / or filter.           V5. 03/03/2008
ANTI-THEFT FUEL DEVICE
ASSEMBLY INSTRUCTIONS
IVECO EUROCARGO - 04 >

Tools needed: 2 screws

1. Wipe the original filler neck.

2. Check that the seal on the anti theft device is correctly in place.

3. Install the Anti-Theft Fuel Device by screwing it on by hand and tighten with a strap wrench (e.g. used
for oil filters)

4. Fix the 2 screws supplied in the two holes inside the Anti-Theft Fuel Device. The screws penetrate the
original filler neck thread and lock the unit in place. Be careful and ensure that no assembly particles fall
into the tank.

5. Use a drill bit to flatten the grooves on the screw heads.

6. Fit a ventilated bayonet fuel tank cap to close the tank. The old cap can no longer be used




We accept no responsibility for damage resulting from incorrect installation. We recommend that installation be carried out by a
                                                                                                                                     IMEX00001E
qualified engineer. Drilling residue etc. remaining in the tank can lead to the destruction of the pump and / or filter.           V5. 03/03/2008

				
DOCUMENT INFO
Shared By:
Categories:
Stats:
views:13
posted:4/2/2011
language:English
pages:6