Docstoc
EXCLUSIVE OFFER FOR DOCSTOC USERS
Try the all-new QuickBooks Online for FREE.  No credit card required.

Electrical Circuits Lab Course Description DC

Document Sample
Electrical Circuits Lab Course Description DC Powered By Docstoc
					                              Electrical Circuits Lab. (610216) :
Course Description:

DC circuits. KVL and KCL. Mesh and nodal circuits analysis. Network theroems transient analysis
of RL. RC and RLC circuits. AC circuit analysis.

Experiment 1:
Resistors,DC Power supplies and DC meters.
The objective of this experiment is to become familiar with the use of DC power supplies,
resistors, color codes,DC meters and to invistigate the Characteristics of Series and
Parallel DC circuits.

Experiment 2:
 Potentiometers, Series-Parallel DC circuits, Wheatestone Bridge and Delta-Y conversion.
The Objective of this experiment is to become familiar with potentiometers, Delta-Y
conversion and wheatestone bridge.

Experiment 3:
Methods of analysis and Superposition principle.
The objective of this experiment is to become familiar with the branch, mech, nodal
analysis techniques and with Superposition Principle.

Experiment 4:
Thevenin's and Norton,s Theorem.
The objective of this experiment is to varify experimentally the thevenin's and norton's
theorem.

Experiment 5:
Maximum Power Transfer and Source Transformation.
The objective of this experiment is to invistigate the conditions for maximum Power
transfer in DC circuits and the source transformation circuits.

Experiment 6:
Capacitors, RC and RL circuits with DC source.
The objective of this experiment is ti become familiar with the behavior of inductors and
capacitors in DC circuits.

Experiment 7:
Oscilloscope: Voltage, Current and Time Constant.
The objective of this experiment to become familiar with oscillscope operating controls
and its voltage, current ,time measurments and with AC signal operating.

Experiment 8:
Oscilloscope: Frequency Measurment.
The objective of this experiment is to become familiar with oscilloscope frequency
measurment.

Experiment 9:
Oscolliscope: Phase Measurment.
The objective of this experiment is to become familiar with oscilloscope phase
measurment.

Experiment 10:
RLC components,Frequency dependence and Frequency response.
The objective of this experiment is to note the effect of frequency on basic RLC circuits.
                              Electrical Machine Lab. (610386) :
Course Description:

Open and short circuit test of transformers .Electrical machines Transformer Generator Motor
analysis and specification.

Experiment 1:
Single Phase Transformer Part (A)
The objective of this experiment is to illustrate the transformer losses and describe the
iron losses then the measurement of the transformer parameters (i.e Winding resistance)
through open circuit test.

Experiment 2:
Single Phase Transformer Part (B)
The objective of this experiment is to illustrate the transformer losses and describe the
cupper losses then the measurement of the transformer parameters through short circuit
test.

Experiment 3:
 Three Phase Transformer Part (A)
The Objective of this experiment is to become familiar with transformer and know the
different connections of the 3 phase transformer and perform the open circuit test (No
load test) in order to measure transformer parameters, Transformation ratio and iron
losses.

Experiment 4:
Three Phase Transformer Part (B)
The Objective of this experiment is to become familiar with transformer and know the
different connections of the 3 phase transformer and perform the Short circuit test in order
to measure transformer parameters and Cupper losses.

Experiment 5:
Loaded Three-Phase Transformer
The objective of this experiment is to understanding the different types of load (resistive,
inductive and capacitive) loads and to understanding the idea of loading transformer with
different loads type will affect on the transformer voltage , and measuring voltage
regulation, transformer efficiency.

Experiment 6:
Three Phase Synchronous Generator
The objective of this experiment is to perform open and short circuit tests in order to
understanding the behavior of synchronous generator ,the relationship between field
current and flux ,synchronous reactance , Measuring winding resistance, Magnetization
curve, and generator equivalent circuit.

Experiment 7:
Loaded Three-Phase Synchronous Generator
The objective of this experiment is to measuring the Voltage regulation, constructing the
circuit of the three-phase synchronous generator and to measure power factor.

Experiment 8:
Three phase synchronous Motor
The objective of this experiment is to Constructing the equivalent circuit of the three-
phase Motor and to getting familiar with the V-curve.
Experiment 9:
Asynchronous Motor
The objective of this experiment is to become familiar No-load and short circuit tests and
Dc test and to Construct the equivalent Circuit.

Experiment 10:
DC – Shunt Motor
The objective of this experiment is to Getting familiar with magnetizing curve and
construct the equivalent circuit of DC Motor.
                   PHILADELPHIA UNIVERSITY
                   FACULTY OF ENGINEERING
                  Department of Electrical Engineering

                                           Course Title: Power System Lab
                                   Prerequisite: Power Systems Analysis(1)
                                                            Credit Hours: 1

                                                              Course Goals:

To introduce the operating performance of transmission line under different
  circumstances and to investigate the operation performance of protective
                                                                     relay.

                                                                 Objectives:

                   At completing this module the student should be able to:
 •   Understand the operation of transmission line.
 •   Simulated and analyze all the inputs and outputs ratings of
     transmission line.
 •   Invest age the effect of the faults that occurs in the transmission line
     and the protection devices performance.
 •   Use the application of power system analysis in real world
     transmission line.
 •   Investigate the operation performance of protective relay.

                                                           Course Contents:

 •   Transmission Line Performance.
 •   Transmission Line Load Characteristics.
 •   Reactive Power Compensation.
 •   Various method of Earthing
 •   Symmetrical and Asymmetrical Faults.
 •   Power System Protection and Relay.
 •   Over/under voltage relay.
 •   Over current relay.
 •   Current transformer.

                                                                References:
                                                   1. Manual sheet.
2. John J. Grainger, and William D. Stevenson, JR, "power System
                                                        Analysis".
                   PHILADELPHIA UNIVERSITY
                   FACULTY OF ENGINEERING
                  Department of Electrical Engineering

                   Course Title: Power System and Electrical Machine Lab
                                    Prerequisite: Power Systems Analysis
                                                          Credit Hours: 1

                                                              Course Goals:

To introduce the operating performance of transmission line under different
         circumstances and electrical machines operation and applications.

                                                                 Objectives:

                   At completing this module the student should be able to:
 •   Understand the operation of transmission line.
 •   Simulated and analyze all the inputs and outputs ratings of
     transmission line.
 •   Invest age the effect of the faults that occurs in the transmission line
     and the protection devices performance.
 •   Learn about types of machines used in real life and understand its
     operation an application.
 •   Using measuring instrument to measure different machines ratings
     under operation and indicate is characteristics.

                                                           Course Contents:

 •   Transmission Line Performance.
 •   Transmission Line Load Characteristics.
 •   Reactive Power Compensation.
 •   Symmetrical and Asymmetrical Faults.
 •   Power System Protection and Relay.
 •   Single and Three-Phase Transformers.
 •   Loaded Three-Phase Transformer.
 •   Three-Phase Synchronous Generator.
 •   Loaded Three-Phase Synchronous Generator.
 •   Three-Phase Asynchronous Motor.
                                                        References:
                                                   1. Manual sheet.
2. John J. Grainger, and William D. Stevenson, JR, "power System
Analysis". 3. George Mc Pherson, and Robert D. Larmore ,"Electrical
                                        Machines and Transformers"
                                 ‫ﺑﺴﻢ اﷲ اﻟﺮﺣﻤﻦ اﻟﺮﺣﻴﻢ‬

‫اﺳﻢ اﻟﻤﺨﺘﺒﺮ : ﻡﺨﺘﻴﺮ اﺟﻬﺰة ﻗﻴﺎس‬
610356 : ‫رﻗﻢ اﻟﻤﺨﺘﺒﺮ‬
804 : ‫رﻗﻢ اﻟﻘﺎﻋــﻪ‬

.‫اﻟﻤﺘﻄﻠﺐ اﻟﺴﺎﺏﻖ : ﻡﺴﺎق اﺟﻬﺰة ﻗﻴﺎس )153016( او ﻡﺘﺰاﻡﻦ‬

‫اﻟﻬﺪف ﻡﻦ اﻟﻤﺨﺘﺒﺮ : إﻋﻄﺎء اﻟﻄﺎﻟﺐ ﻓﻜﺮﻩ ﻋﻦ اﻟﻘﻴﺎﺱﺎت و اﺥﻄﺎء اﻟﻘﻴﺎس و اﻻﺟﻬﺰة اﻟﻤﺴﺘﺨﺪﻡﻪ ﻟﻬﺬا‬
‫اﻟﻐﺮض، ﺑﺎﻻﺿﺎﻓﻪ اﻟﻰ ﻡﺠﻤﻮﻋﻪ ﻡﻦ اﻟﺘﻄﺒﻴﻘﺎت اﻟﻌﻤﻠﻴﺔ اﻟﺘﻲ ﺕﻮﺿﺢ اﻟﺨﻮاص اﻟﻔﻴﺰیﺎﺋﻴﺔ و اﻟﻜﻬﺮﺑﺎﺋﻴﺔ‬
                                               ً
                           .‫(اﻻآﺜﺮ اﺱﺘﺨﺪاﻡﺎ ﻓﻲ اﻟﻤﺠﺎل اﻟﺘﻄﺒﻴﻘﻲ‬Trancducers ) ‫ﻟﻠﻤﺠﺴﺎت‬

:‫أهﻢ اﻟﺘﺠﺎرب اﻟﺘﻲ ﻳﻐﻄﻴﻬﺎ اﻟﻤﺨﺘﺒﺮ‬
            1.                                Error in measurement (Resistance)
            2.          The wheatstone bridge (sensitivity of wheatstone bridge)
            3.                     Measurements of capacitance and wein bridge
            4.             Capacitance and inductive transducers in an FM system
            5.                                                        Strain gages
            6.                        Temperature measurement : the thermistor
            7. Temperature measurement : the platinum resistance thermometry
            8.              Temperature measurement : on-off temperature control
            9.                              Light measurement : the photodiode
            10.                      Light measurement : the photovoltaic cell

                                                      : ‫اهﻢ اﻻﺝﻬﺰة اﻟﻤﺴﺘﺨﺪﻡﻪ ﻓﻲ اﻟﻤﺨﺘﺒﺮ‬
                    - DC Power Supply.
                    - TK 2941A Transducers Kit.
                    - Power Amplifier Kit (TK2941B).
                    - Light Transducers Kit (TK2941).
                    - Heat Transducers Kit (TK2941H).
                    - Light Transducers BOX (TK294).

  ً
. ‫ﻋﺪد اﻟﻄﻠﺒﺔ ﻓﻲ اﻟﺤﺼﻪ اﻟﻤﺨﺒﺮﻳﻪ: )21( اﺛﻨﺎ ﻋﺸﺮ ﻃﺎﻟﺒﺎ‬


‫ﻡﺸﺮف اﻟﻤﺨﺘﺒﺮ‬
‫م. یﺎﺱﺮ اﻟﻘﻄﻮ‬
                                   ‫ﺑﺴﻢ اﷲ اﻟﺮﺣﻤﻦ اﻟﺮﺣﻴﻢ‬

‫اﺳﻢ اﻟﻤﺨﺘﺒﺮ : ﻡﺨﺘﺒﺮ ﺕﺤﻜﻢ ﺁﻟﻲ‬
‫رﻗﻢ اﻟﻤﺨﺘﺒﺮ : 654016‬

‫رﻗﻢ اﻟﻘﺎﻋــﻪ : 408‬

‫اﻟﻤﺘﻄﻠﺐ اﻟﺴﺎﺏﻖ : ﻡﺴﺎق ﺕﺤﻜﻢ ﺁﻟﻲ ) 154016 ( او ﻡﺘﺰاﻡﻦ .‬

‫اﻟﻬﺪف ﻡﻦ اﻟﻤﺨﺘﺒﺮ : یﻬﺪف اﻟﻤﺨﺘﺒﺮ اﻟﻰ اﻋﻄﺎء اﻟﻄﺎﻟﺐ ﺕﻄﺒﻴﻘﺎت ﻋﻤﻠﻴﺔ ﻋﻠﻰ ﻧﻈﻢ اﻟﻤﺴﺎرات اﻟﻤﻐﻠﻘﺔ‬
‫و اﻟﻤﻔﺘﻮﺣﻪ و ﺕﺄﺙﻴﺮاﺕﻬﺎ اﻟﻤﺨﺘﻠﻔﺔ ﻋﻠﻰ اداء اﻟﻨﻈﺎم ﺑﺎﻻﺿﺎﻓﺔ اﻟﻰ اﺱﺘﺨﺪام ﺑﺮﻧﺎﻡﺞ )‪ (MATLAB‬ﻓﻲ‬
‫ﺣﻞ اﻟﻜﺜﻴﺮ ﻡﻦ ﻡﺸﺎآﻞ ﻧﻈﻢ اﻟﺘﺤﻜﻢ ، و ﺣﻞ ﻡﺴﺎﺋﻞ و ﻡﺸﻜﻼت ریﺎﺿﻴﺔ یﻮاﺟﻬﻬﺎ اﻟﻄﻼب ﻓﻲ ﻡﺴﺎق و‬
                                                                      ‫ﻡﺨﺘﺒﺮ اﻟﺘﺤﻜﻢ اﻻﻟﻲ.‬

‫اهﻢ اﻟﺘﺠﺎرب اﻟﺘﻲ یﻐﻄﻴﻬﺎ اﻟﻤﺨﺘﺒﺮ:‬

                                                          ‫.‪Matrix Algebra with Matlab‬‬
           ‫.1‬
           ‫.2‬                      ‫.‪Introduction to Complex numbers using Matlab‬‬
           ‫.3‬                                       ‫‪Polynomials and time functions‬‬
           ‫.4‬                       ‫‪Introduction to simulation of dynamic systems‬‬
           ‫.5‬                                 ‫‪Motor speed vs. input characteristics‬‬
           ‫.6‬                                 ‫‪Motor speed vs. load characteristics‬‬
           ‫.7‬                             ‫‪Fundamental closed-loop speed control‬‬
           ‫.8‬                                  ‫‪Gain of the system vs. speed control‬‬
           ‫.9‬                                          ‫‪Closed loop position control‬‬
           ‫.01‬                                 ‫‪Speed feedback and position control‬‬
           ‫.11‬
           ‫.21‬
           ‫.31‬
           ‫.41‬
           ‫.51‬
           ‫.61‬
           ‫.71‬


                                                      ‫: اهﻢ اﻻﺝﻬﺰة اﻟﻤﺴﺘﺨﺪﻡﻪ ﻓﻲ اﻟﻤﺨﺘﺒﺮ‬
                 ‫ﺑﺮﻧﺎﻡﺞ1.6 ‪- Matlab ver‬‬
                 ‫‪- E-D-4400 Modular Servo Trainer‬‬
  ‫ً‬
‫ﻋﺪد اﻟﻄﻠﺒﺔ ﻓﻲ اﻟﺤﺼﻪ اﻟﻤﺨﺒﺮﻳﻪ: )61( ﺳﺘﺔ ﻋﺸﺮ ﻃﺎﻟﺒﺎ .‬


                                                     ‫ﻡﺸﺮف اﻟﻤﺨﺘﺒﺮ‬

                                                        ‫م. ﻳﺎﺳﺮ اﻟﻘﻄﻮ‬

				
DOCUMENT INFO