Docstoc

CIIT slot type screwdriver

Document Sample
CIIT slot type screwdriver Powered By Docstoc
					                            Title:
                            NAVIGATION INSTALLATION MANUAL




                                                                   CIIT0590
                            With Bluetooth Instructions (Tundra)
           Customization
Installation Instructions
                            Models:
        August 29, 2008
                            2008 Toyota Tundra
TABLE OF CONTENTS

                                                        Page No.
1.        DEFINITION OF TERMS                              3
2.        PRECAUTIONS FOR INSTALLATION                   4~7
3.        INSTALLATION PREPARATION                       8 ~ 13
      –       CHART: FM1, FM2 AND AM PRE-SET STATIONS

4.        RECOMMENDED TOOLS                               14
5.        INSTALLATION OUTLINE                            15
6.        CAR-NAVI PARTS DESCRIPTION                      16
7.        DISASSEMBLY
      ‰       BASIC
                                                        17 ~ 29
      ‰       BLUETOOTH/VOICE RECOGNITION
      ‰       REAR CAMERA

8.        INSTALLATION
      ‰       BASIC
                                                        30 ~ 47
      ‰       BLUETOOTH/VOICE RECOGNITION
      ‰       REAR CAMERA

9.        GPS ANTENNA INSTALLATION                      48 ~ 50
10.       OPERATION CHECK
      ‰       DISPLAY CHECK MODE
      ‰       NAVIGATION CHECK MODE
      ‰       BLUETOOTH CHECK                           51 ~ 59
      ‰       VOICE RECOGNITION CHECK
      ‰       AUX PORT
      ‰       REAR CAMERA

11.       RE-INSTALLATION                                 60
12.       RE-INITIALIZING                               61 ~ 62
13.       TROUBLESHOOTING HINTS                         63 ~ 64
14.       DIAGNOSTIC CHART                              65 ~ 69
1. DEFINITION OF TERMS

   WARNING:                    Describes precautions that should be
                               observed, in order to prevent injury or
                               death to the user during installation.


   CAUTION:                    Describes precautions that should be
                               observed, in order to prevent damage
                               to the vehicle or its components,
                               which may occur during installation if
                               insufficient care is taken.

   NOTE:                       Provides additional information that
                               facilitates installation work.

   FRONT, REAR, LEFT, RIGHT:   Provides additional information
                               that facilitates installation work.

   TOOLS:                      Specifies the tools and equipment
                               recommended for this process.


   ESD:                        Contains parts and assemblies
                               susceptible to damage by
                               Electrostatic Discharge (ESD).

                               To prevent unnecessary
                               troubleshooting, after an installation
                               procedure.




                                                                     3
2. PRECAUTIONS FOR INSTALLATION
1.      Contents given in the WARNING and CAUTION in this manual must be
        carefully followed during the installation. If they are ignored, functions
        of the CAR-NAVI system are hindered, as well as personal injury or
        damage to the vehicle may result. Always carry out the installation in
        accordance with the WARNING and CAUTION as noted.
2.      When the vehicle parts are removed, keep the tapping screws, bolts and
        nuts organized so that the re-assembly will proceed correctly.
3.      Do NOT remove vehicle parts except for those that are specified in this
        manual.
4.      Not all digital photographs depicted in this Installation Manual, will
        reflect the current model and model year vehicle.

                                                       WARNING
       LOCK &                                   Failure to carry out these
      REMOVE!                                   procedures, will result in a possible
                                                deployment of airbag(s), personal
                                                injuries, or unnecessary repairs to
                                                the Supplemental Restraint System
                                                (SRS).
                                                Turn the key switch to the LOCK
                                                position. Next, remove the key from
                                                the ignition switch.




                     NEGATIVE
                                                       CAUTION
                     TERMINAL                   Do NOT work on the vehicle
                                                while the battery’s NEGATIVE
                                                terminal is connected. Working
                                                on the vehicle with the battery
                                                connected, may result in a short
                                                circuit during the CAR-NAVI KIT
                                                installation.
     FRONT




                                                Tools: 10mm Wrench
                            BATTERY                                              4
2. PRECAUTIONS FOR INSTALLATION

                                WARNING
                       Never use a voltmeter to
                       troubleshoot any of the harnesses
                       or connectors to the SRS.
                       Accidentally probing the
                       connectors to the SRS can lead to
                       deployment of the airbag.
                       SRS wire harness loom or cover is in
                       bright yellow colour.




                           NOTE
    VINYL              Take care NOT to scratch any part of
    TAPE               the vehicle. Bind the tips of tools (i.e.:
                       clip remover, slot screwdriver, etc.)
                       with a piece of vinyl tape to prevent
                       damage to parts of the vehicle.




                           NOTE
            GOOD!      Cut away the excess part of all cable
                       ties, after fastening it.




                                                            5
2. PRECAUTIONS FOR INSTALLATION

                                     NOTE
                                 Carefully handle all connectors. Firmly
                                 attach the connectors during
                                 installation. The connector should click
                     CONNECTOR   shut.
                                 Detach locking connectors by first
                                 releasing the lock and pulling only on
                                 the connector itself.




          RUN-WIRE
          RUN-                       NOTE
          SECTION                Ensure that the run-wire is properly in
                      RUN-
                      RUN-       place of the RUN-WIRE SECTION, as
   BASE               WIRE       shown on the photo on the left. Always
                                 fold the BASE over to meet the RUN-
                                 WIRE SECTION, shown with the
                                 yellow arrow. Use ordinary pliers to
                                 squeeze the base and run-wire
                                 section, until the latch locks.




                                     NOTE
                                 Use protective covers to avoid damage
                                 and scratches to the vehicle
                                 components.
                                 •Seat cover
                                 •Fender cover (photo)
                                 •Floor cover


    FENDER                                                         6
    COVER
2. PRECAUTIONS FOR INSTALLATION
     CONNECTOR VIEWS                NOTE
      K1           K2
                                All connector views in this installation
                                manual, are viewed from the front side.



     K3


                 (Front View)




                                                                  7
3. INSTALLATION PREPARATION
•    Prior to installing the CAR-NAVI System kit, check the following for damage or
     malfunction:
     •     Internal and external trim and body work.
     •     Following vehicle functions:
           •        Radio (FM1, FM2, AM)
           •        Automatic Climate Control System (i.e.: AUTO, A/C, TEMP, FAN
                    SPEED CONTROL, ALL VENT MODES, REAR DEFROST,
                    SECURITY, HAZARD LIGHTS, etc.).
•    CAR-NAVI system parts preparation:
     •     When unpacking the CAR-NAVI system kit, lay out all components in the
           order of installation and check for missing or damaged parts.

                                                       NOTE
                                                  Before proceeding with the CAR-
                                                  NAVI kit installation, please remove
                                                  any audio CD(s) from the factory
                                                  radio assembly. Also, please
                                                  ensure that the pre-set radio
                                                  stations (FM1, FM2 and AM) are
                                                  written down to pre-set the AVN-S
                                                  display unit. Please use chart
                                                  below.




CHART: FM1, FM2 AND AM PRE-SET STATIONS

                1             2            3            4            5            6
    FM1
    FM2
    AM

                                                                                      8
3. INSTALLATION PREPARATION: Basic Installation

     STEREO COMPONENT                   NOTE
         AMPLIFIER
                                     Please order the appropriate Stereo
                                     Component Amplifier from the Toyota
                                     Parts Department. This part is NOT
                                     included in the Car Navigation Kit.




      AUDIO UPGRADE WIRE                NOTE
           HARNESS
                                     Please order the Audio Upgrade W/H
                                     from the Toyota Parts Department.
                                     This part is NOT included in the Car
                                     Navigation Kit.




                           BRACKET
                             KIT
                                        NOTE
                                     Please order the Bracket kit from the
                                     Toyota Parts Department. This part is
                                     NOT included in the Car Navigation
                                     Kit.




                                                                     9
3. INSTALLATION PREPARATION: Basic Installation

    AUX &                       NOTE
  STEERING
   SW W/H                    Please order the AUX & Steering SW
                             Wire Harness, from the Toyota Parts
                             Department. This part is NOT included
                             in the Car Navigation Kit.




SHIELDED WIRE                   NOTE
   HARNESS
                             Please order the Shielded Wire
                             Harness, from the Toyota Parts
                             Department. This part is NOT included
                             in the Car Navigation Kit.




                   MAP DVD      NOTE
                             Please order the most recent version
                             of Map DVD, from the Toyota Parts
                             Department. This part is NOT included
                             in the Car Navigation Kit.




                                                           10
3. INSTALLATION PREPARATION: Basic Installation

                               NOTE
           AUX FIX          Please order the AUX Fix Adapter,
          ADAPTER
                            from the Toyota Parts Department.
                            This part is NOT included in the Car
                            Navigation Kit.




                               NOTE
      NAVIGATION BRACKETS
            #1 AND #2       Please order the appropriate
                            Navigation Brackets #1 and #2, from
                            the Toyota Parts Department. This
                            part is NOT included in the Car
                            Navigation kit.




                                                            11
3. INSTALLATION PREPARATION: Bluetooth/Voice Recognition

 MIC+TALK SWITCH                    NOTE
  WIRE HARNESS
                                 Please order the MIC+Talk Switch
                                 Wire Harness from the Toyota Parts
                                 Department. This part is NOT included
                                 in the Car Navigation Kit.




                                    NOTE
                                 Please order the appropriate
                                 Microphone Amplifier Assembly (MIC)
                                 from the Toyota Parts Department.
                                 This part is NOT included in the Car
                                 Navigation Kit.




TALK SWITCH WIRE                    NOTE
    HARNESS
                                 Please order the Talk Switch Wire
                                 Harness, from the Toyota Parts
                                 Department. This part is NOT included
                                 in the Car Navigation Kit.




                                                               12
3. INSTALLATION PREPARATION: Rear Camera

                           NOTE
 CAMERA ADAPTER
  WIRE HARNESS          Please order the Camera Adapter
                        Wire Harness from the Toyota Parts
                        Department. This part is NOT included
                        in the Car Navigation Kit.




                           NOTE
                        Please order the Camera kit from the
                        Toyota Parts Department. This part is
                        NOT included in the Car Navigation
                        Kit.




                                                       13
 4. RECOMMENDED TOOLS
Safety Tools:                                    Comments:
Safety Goggles
Floor Protectors
Fender Covers
Seat Covers
Installation Tools:                              Comments:
Ratchet ¼” Drive
8mm socket (¼”)
10mm socket (¼”) > Standard&Deep
Torque Wrench ¼” Drive                           4.0 N•m, 41kgf•cm, 36lbf•in
Ratchet 3/8” Drive
10mm socket (3/8”)
11mm or 7/16” socket (¼”)
6” Extension (3/8”)
10mm Wrench
Long and Short Tip Screwdriver
(Philips Type)
Pliers
Nylon Removal Tool
Vinyl Tape
Side Cutters
Drill (Electric/Pneumatic)
#10 Drill Bit
Manuals:                                         Comments:
2007~ Toyota Tundra Repair Manual
2007~ Toyota Tundra: Electrical Wiring Diagram                                 14
5. INSTALLATION OUTLINE
               INTERIOR VIEW

                             MICROPHONE
                               (OPTION)

                                  GPS
                                ANTENNA
                                       AVN-
                                       AVN-S
                                   DISPLAY UNIT




                                       AUDIO            STEREO
                                    UPGRADE W/H       COMPONENT
                                                       AMPLIFIER
               TALK SWITCH   AUX PORT
                 (OPTION)




                               EXTERIOR VIEW
                                                    REAR
                                                  CAMERA
                                                  (OPTION)




                                                             15
6. CAR-NAVI PARTS DESCRIPTION
1                    2                 3        LENGTH
                                                         SHORT                    4




                                                                                      ELECTRO-
                                                                                      ELECTRO-
                                                                                        TAP™
                                                                                        TAP™
                     5
                                                  8               9

                          6

                                                                  7

    10

                                           11                         12




No.                 Part Name                   TOYOTA Part No.            Q’ty
1        AVN-S Display Unit                       86120-06390               1
2        GPS Antenna                              08663-00340               1
3        GPS Antenna Bracket                                                1
4        5 Pin Wire Harness                                                 1
5        Cable Tie (11”)                                                    4
6        Cable Tie (7.5”)                                                   3
7        Cable Tie (4”)                                                    10
8        Push Pin (STT)                                                     1
9        Foam                                                              10
10       Double Coated Tape                                                 1
11       Trim Screws (#10-16 u 5/8”)                                        2
12       Owner’s Manual (English and                                        1
         French)



NOTE: NOT ALL COMPONENTS WILL BE USED FOR THE INSTALLATION METHOD.
                                                                                       16
7. DISASSEMBLY: Basic

               NEGATIVE
                                      CAUTION
               TERMINAL        Do NOT work on the vehicle
                               while the battery’s NEGATIVE
                               terminal is connected. Working
                               on the vehicle with the battery
                               connected, may result in a short
                               circuit during the CAR-NAVI KIT
                               installation.
  FRONT




                               Tools: 10mm Wrench
                     BATTERY


                               Temporary removal of part(s):
                               •Front Scuff Plate (RH)




             FRONT SCUFF
              PLATE (RH)



                               Temporary removal of part(s):
                               Remove the NUT CLIP.
                               •Kick Panel (RH)
 NUT
 CLIP
            KICK PANEL
               (RH)
    FR
      ON
        T




                                                               17
7. DISASSEMBLY: Basic

                              Temporary removal of part(s):
                              •Instrument Side Panel (RH)

     LOWER                    Tools: Nylon Removal Tool
  INSTRUMENT
 SUB-
 SUB-ASSEMBLY        PANEL
                   ASSEMBLY
                      (RH)




      LOWER                   Temporary removal of part(s):
            SUB-
 INSTRUMENT SUB-              •Screw (1)
    ASSEMBLY
                                  : SCREW × 1

                              Tools: Long Tip Screwdriver (Philips
                                    Type)




      LOWER                   Temporary removal of part(s):
            SUB-
 INSTRUMENT SUB-
    ASSEMBLY
                              •Bolt (1)

                                  : BOLT × 1

                              Tools: Ratchet ¼” Drive, 10mm socket
                                    (¼”)




                                                              18
7. DISASSEMBLY: Basic
                                     Place the glove box to the open
                                     position, as indicated on the photo.
                                     Temporary removal of part(s):
                                     •Screws (2)
                                     •Lower Instrument Sub-Assembly

                                         : SCREW × 2

           LOWER                     Tools: Short Tip Screwdriver (Philips
                 SUB-
      INSTRUMENT SUB-                      Type
         ASSEMBLY




                                     <<Floor Shift>>:
                        CUP HOLDER   Temporary removal of part(s):
                                     •Cup Holder
                                     •Upper Console Panel




                            UPPER
                           CONSOLE
                            PANEL



                                     <<Floor Shift>>:

   SHIFT KNOB                        Temporary removal of part(s):
           CENTER LOWER
                                     •Center Lower Instrument Panel
            INSTRUMENT
               PANEL                 •Connectors




                                                                      19
7. DISASSEMBLY: Basic

                                    <<Column Shift>>:
                                    Temporary removal of part(s):
                                    •Clip (1) - LH

                                        : CLIP × 1

              CENTER LOWER          Tools: Short Tip Screwdriver (Philips
                 COVER                    Type




                                    <<Column Shift>>:
                       CUP HOLDER   Temporary removal of part(s):
                                    •Clip (1) – RH
                                    •Center Lower Cover
        CENTER LOWER
                                        : CLIP × 1
           COVER

                                    Tools: Short Tip Screwdriver (Philips
                           UPPER          Type
                          CONSOLE
                           PANEL



                                    <<Column Shift>>:

   SHIFT KNOB
                                    Loosen the following part(s):
           CENTER LOWER             •Lower Instrument Panel
            INSTRUMENT
               PANEL




           LOWER
        INSTRUMENT
           PANEL

                                                                    20
7. DISASSEMBLY: Basic

                                     <<Column Shift>>:
                      LOWER          Temporary removal of part(s):
                   INSTRUMENT
                     CLUSTER         •Screw (1)
   LOWER
INSTRUMENT
   PANEL
                                          : SCREW × 1

                                     Tools: Long Tip Screwdriver (Philips
                                           Type)




                  LOWER INSTRUMENT   <<Column Shift>>:
                      CLUSTER
   SHIFT KNOB                        Temporary removal of part(s):
           CENTER LOWER
            INSTRUMENT               •Ash Box (not shown)
               PANEL                 •Screw (1)
                                     •Lower Instrument Cluster
                                     •Connectors

                                          : SCREW × 1




                                     <<Column Shift>>:
                                     Loosen the following part(s):
                                     •Door Box




      DOOR BOX
                                                                     21
7. DISASSEMBLY: Basic

                        <<Column Shift>>:
                        Temporary removal of part(s):
                        •Screw (2)

                             : SCREW × 2

                        Tools: Long Tip Screwdriver (Philips
                              Type)




                        <<Column Shift>>:
           CUP HOLDER
            ASSEMBLY    Temporary removal of part(s):
                        •Screw (2)
                        •Cup Holder Assembly

                             : SCREW × 2




                        Use the nylon removal tool, to
                        temporary loosen the following part(s):
                        •Instrument Cluster Finish Panel

                        Tools: Nylon Removal Tool




 INSTRUMENT
CLUSTER FINISH
    PANEL                                               22
7. DISASSEMBLY: Basic
                                      Temporary removal of part(s):
              MANUAL A/C
               SYSTEM
                                      •Manual A/C System
                                      •Connectors




                                      Remove 4 bolts and then carefully
                                      remove the Radio Receiver. Next,
                                      disconnect the connector and the
                                      antenna connector.

                                          : BOLT × 4

                                      Tools: Ratchet ¼ ” Drive, 6” Extension
                                            (¼), 10mm socket (¼”)




                            RADIO     Remove 3 bolts (re-use). Next, remove
                           RECEIVER   radio bracket #1. Discard this bracket.

                                          : BOLT × 3

                                      Tools: Ratchet ¼” Drive, 8mm socket
                                            (¼”), Short Tip Screwdriver (Philips
                                            Type)



   RADIO
 BRACKET #1                                                           23
7. DISASSEMBLY: Basic

   RADIO
    RADIO                           Remove 3 bolts (re-use). Next, remove
  RECEIVER #2
  BRACKET                           radio bracket #1. Discard this bracket.

                                        : BOLT × 3

                                    Tools: Ratchet ¼” Drive, 8mm socket
                                          (¼”), Short Tip Screwdriver (Philips
  RADIO                                   Type)
 RECEIVER
W/ HEATER
 CONTROL
 RADIO
BRACKET
   #2



Following procedures are only applicable for disassembly of
the Bluetooth/Voice Recognition and/or Rear Camera OPTIONS.
Please proceed to the necessary procedures.
If these procedures are not required, please skip to the
INSTALLATION: BASIC.




                                                                    24
7. DISASSEMBLY: BLUETOOTH/Voice Recognition

                           Temporary removal of part(s):
                           •5 torx screws (Not Shown)
            ROOF CONSOLE   •Roof Console Box Assembly
            BOX ASSEMBLY
                           •Connectors

                              : SCREW × 5

                           Tools: T-20 Torx Driver, Nylon Removal
                                 Tool




    VISOR                  Temporary removal of part(s):
   HOLDER
                           • Torx Screw
                           •Visor Holder

                              : SCREW × 1

                           Tools: T-20 Torx Driver




                           Temporary removal of part(s):
  VISOR                    •Visor Cover (not shown)
   (LH)
                           •3 Torx Screws
                           •Connector (where applicable)
                           •Visor (LH)

                              : SCREW × 3

                           Tools: T-20 Torx Driver, Nylon Removal
                                 Tool                     25
7. DISASSEMBLY: BLUETOOTH/Voice Recognition

        FRONT PILLAR     Temporary removal / loosen of part(s):
        GARNISH (LH)     •Cover
                         •10mm Bolt
                         •Loosen Front Pillar Garnish (LH)

                            : BOLT × 1

           COVER         Tools: Ratchet 3/8” Drive, 10mm Deep
                               socket (3/8”), Nylon Removal Tool




                         Temporary removal / loosen of part(s):
      ROOF HEADLINING    •Loosen the Roof Headlining
         ASSEMBLY
                         Assembly.




                         Temporary removal / loosen of part(s):
                         •Side Panel (LH)

                         Tools: Nylon Removal Tool




         SIDE PANEL
            (LH)
                                                        26
7. DISASSEMBLY: BLUETOOTH/Voice Recognition

            LOWER INSTRUMENT   Temporary removal/loosen of part(s):
               PANEL (LH)
                               • 1 Bolt
                               •Loosen the Lower Instrument Panel
                               (LH)

                                  : BOLT × 1

                               Tools: Ratchet ¼” Drive, 10mm Deep
                                     Socket (¼”), Nylon Removal Tool




                                                              27
7. DISASSEMBLY: REAR CAMERA

                             NOTE
                          Please ensure that the Camera Kit
                          is installed, prior to any kind of
                          parts removal from the vehicle. For
                          installation of this Camera Kit,
                          please consult with the kit
                          installation manual.




                          Temporary removal of part(s):
                          •2 Screws
            BOX DOOR
          SUB-ASSEMBLY
                          Tools: Long Tip Screwdriver (Philips)
          SUB-
                             : SCREW × 2



   REAR SCUFF
    PLATE (RH)




                          Temporary removal of part(s):
             BOX DOOR
           SUB-ASSEMBLY
           SUB-           •2 Panel Hole Covers (not shown)
                          •2 Screws
                          Use vinyl tape to cover the tip of the
                          slot driver, to remove the covers.

                          Tools: Long Tip Screwdriver (Philips),
                                Long Tip Screwdriver (Slot), Vinyl
                                Tape
                                : SCREW × 2               28
7. DISASSEMBLY: REAR CAMERA

                       Temporary removal of part(s):
        BOX DOOR       •2 Screws
      SUB-
      SUB-ASSEMBLY
                       •Box Door Sub-Assembly

                       Tools: Long Tip Screwdriver (Philips)

                          : SCREW × 2




                                                       29
8. INSTALLATION: Basic
                                     Install the NAVI Bracket #1, onto the
                      NAVI BRACKET
                                     AVN-S Display Unit and then tighten
                            #1
                                     with the 3 bolts. Fourth bolt is not
                                     required.

                                         : BOLT × 3

                                     Tools: Ratchet ¼” Drive, 8mm socket
                                           (¼”), Short Tip Screwdriver (Philips
                                           Type)




                                     Install the NAVI Bracket #2, onto the
 NAVI BRACKET                        AVN-S Display Unit and then tighten
       #2
                                     with the 3 bolts. Fourth bolt is not
                                     required. Afterwards, place the unit
                                     aside.

                                         : BOLT × 3

                                     Tools: Ratchet ¼” Drive, 8mm socket
                                           (¼”), Short Tip Screwdriver (Philips
                                           Type)




         RADIO RECEIVER AREA
                                     Once the original radio receiver and
                                     heater control has been removed,
                                     locate connector K1 and K2. Please
                                     review below for the connector
                K2
        K1                           diagram.
                                            K1                       K2




                                                      (Front View)


                                                                          30
8. INSTALLATION: Basic
                                       Install mating end of the audio upgrade wire
                                       harness, to connectors to K1 and K2. Use 4
       FOAM X 2                        foams to cover the connectors of the audio
                                       upgrade wire harness. The other end of the
                                       audio upgrade wire harness, should be routed
                                       to the glove compartment area.
  K1
                                       Next, locate connector K4 on the audio
                                       upgrade wire harness.
                   FOAM X 2                                 K4

             K2

                              K4

                                                        (Front View)


                                       Once connector K4 (audio upgrade
        K4                    AUDIO    W/H) is located, route the 5 pin wire
                             UPGRADE   harness (dotted red line) beside and
                               W/H
                                       along the audio upgrade wire harness,
                                       as shown on the photo. Use ONE 4”
                                       cable tie, to fasten the 5 pin wire
                                       harness to the audio upgrade W/H.
                                       Only route the BROWN wire (w/ gray
                                       dot, REVERSE) towards the glove
                          5 PIN
                          WIRE         compartment area.
                        HARNESS
                                          :4” CABLE TIE u 1
                                       Tools: Side Cutter

       RADIO RECEIVER AREA             Locate the 20 pin connector (K3).
                                       Please review the photo. For further
              K3
                                       information, please consult with the
                                       Toyota Tundra Electrical Wiring
                                       Diagram.
                                       Ensure that the secondary lock of
                                       the connector is loosened.




                                                                            31
8. INSTALLATION: Basic

                                                  NOTE
                                             Connect the SPEED signal:
                                             Once connector K3 is located, locate pin 3.
                                             Please review the illustration below. The wire
                                             colour is WHITE (SPD signal). Please consult
                                             with the Toyota Tundra Electrical Wiring
                                             Diagram.
                                                                       K3


                K3
                                              PIN 3



                                                                    (Front View)


                                                  NOTE
                     SPEED
                      WIRE                   Once the SPEED signal wire (white w/ grey dot) has been
 RUN WIRE                                    tapped (red Electro-Tap), use ONE Foam provided in the
 SECTION                                     CAR-NAVI kit, to wrap the electro-tap. Use ONE Foam
                             BASE            provided in the CAR-NAVI kit, to wrap the ELECTRO-
                                             TAP™ (SPEED Signal). Please ensure that the SPEED
                                             wire has been properly latched. Use the digital tester,
                                             to ensure that the connection is good.
                                             Use ONE 4” cable tie, to wrap the excess SPEED wire
                                             from the 5 pin W/H.


                                                 :4” CABLE TIE u 1

                                              Tools: Pliers, Side Cutters, Digital Tester
                                5 PIN W/H




                 K3                               NOTE
                                             Connect the shielded wire harness, the end with 3
                                             wires (red, green black), to the 20 pin connector
                                             (K3). Please review the connector illustration
                                             (LEFT) for the connection, and chart below. Ensure
                                             that the secondary lock is loosened, on connector
                                             K3. After ALL wires are in place, ensure that the
                                             secondary lock is locked once again.

                                              PIN LOCATION       WIRE COLOUR            SIGNAL

                                                    11                RED                 IVO+

                                                    12               GREEN                IVO-
  RED   BLACK                                       13               BLACK                32
                                                                                         SLD1
   GREEN                      (Front View)
                                                                                        SB-CNS-IH-10292007


                SERVICE BULLETIN
                                   CAR NAVIGATION SYSTEM
                                         INSTALLATION HINT                                       October, 2007

Subject:                  Stereo Jack Adapter (AUX)
Outline:                  This bulletin was created to inform Toyota dealers that for some
                          vehicles with dealer installed navigation systems, the Stereo Jack
                          Adapter may not function properly. By following these procedure
                          (for corresponding vehicles), this will enable the Stereo Jack
                          Adapter (AUX), to function properly.
    E) Applicable Information (Tundra Gasoline, 4 X 2)
  CAR-NAVI Kit P/N         Vehicle & Model         Audio System          Model Year               Model Code
                                                                                                UCK50L-TRADKA
                                                                                                UCK51L-THADKA
                                                                                                UCK51L-CRASKA
                                                                                                UCK51L-CRALKA
                                                    Without JBL                                 UCK52L-CHASKA
  PU069-34007-G5            Tundra (4 X 2)                                2007MY~
                                                     With JBL                                   USK50L-TRTDKA
                                                                                                USK51L-THTDKA
                                                                                                USK51L-CRTSKA
                                                                                                USK51L-CRTLKA
                                                                                                USK52L-CHTSKA

                                  K3                                                <<WITHOUT JBL>>

                                                                               K1

       (Front View)
                                                                                              (Front View)

                                                    AUX FIX ADAPTER
                                                                                        ELECTRO-
                                                                                        ELECTRO-
                      ELECTRO-
                      ELECTRO-
                                                                                          TAP
                        TAP

 Use the AUX Fix Adapter (orange dotted square) to bridge 2 wires from the vehicle side. Next, locate
 connector K3 (20 pin connector) and find pin 18 (AUXG, grey). Use the red Electro-Tap to tap into pin 18
 (AUXG, grey). Lastly, locate connector K1 (10 pin connector) and find pin 7 (GND, white w/ black tracer). Use
 the blue Electro-Tap to tap into pin 7 (GND, white w/ black tracer). Conduct a continuity check, to determine
 good connection.
 Finally, please ensure that an external device or dummy jack is used to enable to the AUX.



                                                                                      DENSO Sales Canada, Inc.
                                                                                         Aftermarket Department
                                                                                        SB-CNS-IH-10292007


                SERVICE BULLETIN
                                   CAR NAVIGATION SYSTEM
                                         INSTALLATION HINT                                       October, 2007

Subject:                  Stereo Jack Adapter (AUX)
Outline:                  This bulletin was created to inform Toyota dealers that for some
                          vehicles with dealer installed navigation systems, the Stereo Jack
                          Adapter may not function properly. By following these procedure
                          (for corresponding vehicles), this will enable the Stereo Jack
                          Adapter (AUX), to function properly.
    E) Applicable Information (Tundra Gasoline, 4 X 2)
  CAR-NAVI Kit P/N         Vehicle & Model         Audio System          Model Year               Model Code
                                                                                                UCK50L-TRADKA
                                                                                                UCK51L-THADKA
                                                                                                UCK51L-CRASKA
                                                                                                UCK51L-CRALKA
                                                    Without JBL                                 UCK52L-CHASKA
  PU069-34007-G5            Tundra (4 X 2)                                2007MY~
                                                     With JBL                                   USK50L-TRTDKA
                                                                                                USK51L-THTDKA
                                                                                                USK51L-CRTSKA
                                                                                                USK51L-CRTLKA
                                                                                                USK52L-CHTSKA

                                                                                      <<WITH JBL>>
                                 K3                                     K4




       (Front View)
                                                                                              (Front View)

                                                    AUX FIX ADAPTER
                                                                                                 ELECTRO-
                                                                                                 ELECTRO-
                      ELECTRO-
                      ELECTRO-
                                                                                                   TAP
                        TAP

 Use the AUX Fix Adapter (orange dotted square) to bridge 2 wires from the vehicle side. Next, locate
 connector K3 (20 pin connector) and find pin 18 (AUXG, grey). Use the red Electro-Tap to tap into pin 18
 (AUXG, grey). Lastly, locate connector K4 (20 pin connector) and find pin 20 (GND, white w/ black tracer). Use
 the blue Electro-Tap to tap into pin 20 (GND, white w/ black tracer). Conduct a continuity check, to determine
 good connection.
 Finally, please ensure that an external device or dummy jack is used to enable to the AUX.


                                                                                      DENSO Sales Canada, Inc.
                                                                                         Aftermarket Department
                                                                                        SB-CNS-IH-10292007


                SERVICE BULLETIN
                                   CAR NAVIGATION SYSTEM
                                         INSTALLATION HINT                                       October, 2007

Subject:                  Stereo Jack Adapter (AUX)
Outline:                  This bulletin was created to inform Toyota dealers that for some
                          vehicles with dealer installed navigation systems, the Stereo Jack
                          Adapter may not function properly. By following these procedure
                          (for corresponding vehicles), this will enable the Stereo Jack
                          Adapter (AUX), to function properly.
    F) Applicable Information (Tundra Gasoline, 4 X 4)
  CAR-NAVI Kit P/N         Vehicle & Model         Audio System          Model Year               Model Code
                                                                                                UCK55L-TRADKA
                                                                                                UCK56L-THADKA
                                                                                                UCK56L-CRASKA
                                                                                                UCK56L-CRALKA
                                                    Without JBL                                 UCK57L-CHASKA
  PU069-34007-G5            Tundra (4 X 4)                                2007MY~
                                                     With JBL                                   USK55L-TRTDKA
                                                                                                USK56L-THTDKA
                                                                                                USK56L-CRTSKA
                                                                                                USK56L-CRTLKA
                                                                                                USK57L-CHTSKA

                                  K3                                                <<WITHOUT JBL>>

                                                                               K1

       (Front View)
                                                                                              (Front View)

                                                    AUX FIX ADAPTER
                                                                                        ELECTRO-
                                                                                        ELECTRO-
                      ELECTRO-
                      ELECTRO-
                                                                                          TAP
                        TAP

 Use the AUX Fix Adapter (orange dotted square) to bridge 2 wires from the vehicle side. Next, locate
 connector K3 (20 pin connector) and find pin 18 (AUXG, grey). Use the red Electro-Tap to tap into pin 18
 (AUXG, grey). Lastly, locate connector K1 (10 pin connector) and find pin 7 (GND, white w/ black tracer). Use
 the blue Electro-Tap to tap into pin 7 (GND, white w/ black tracer). Conduct a continuity check, to determine
 good connection.
 Finally, please ensure that an external device or dummy jack is used to enable to the AUX.



                                                                                      DENSO Sales Canada, Inc.
                                                                                         Aftermarket Department
                                                                                        SB-CNS-IH-10292007


                SERVICE BULLETIN
                                   CAR NAVIGATION SYSTEM
                                         INSTALLATION HINT                                       October, 2007

Subject:                  Stereo Jack Adapter (AUX)
Outline:                  This bulletin was created to inform Toyota dealers that for some
                          vehicles with dealer installed navigation systems, the Stereo Jack
                          Adapter may not function properly. By following these procedure
                          (for corresponding vehicles), this will enable the Stereo Jack
                          Adapter (AUX), to function properly.
    F) Applicable Information (Tundra Gasoline, 4 X 4)
  CAR-NAVI Kit P/N         Vehicle & Model         Audio System          Model Year               Model Code
                                                                                                UCK55L-TRADKA
                                                                                                UCK56L-THADKA
                                                                                                UCK56L-CRASKA
                                                                                                UCK56L-CRALKA
                                                    Without JBL                                 UCK57L-CHASKA
  PU069-34007-G5            Tundra (4 X 4)                                2007MY~
                                                     With JBL                                   USK55L-TRTDKA
                                                                                                USK56L-THTDKA
                                                                                                USK56L-CRTSKA
                                                                                                USK56L-CRTLKA
                                                                                                USK57L-CHTSKA

                                                                                      <<WITH JBL>>
                                 K3                                     K4




       (Front View)
                                                                                              (Front View)

                                                    AUX FIX ADAPTER
                                                                                                 ELECTRO-
                                                                                                 ELECTRO-
                      ELECTRO-
                      ELECTRO-
                                                                                                   TAP
                        TAP

 Use the AUX Fix Adapter (orange dotted square) to bridge 2 wires from the vehicle side. Next, locate
 connector K3 (20 pin connector) and find pin 18 (AUXG, grey). Use the red Electro-Tap to tap into pin 18
 (AUXG, grey). Lastly, locate connector K4 (20 pin connector) and find pin 20 (GND, white w/ black tracer). Use
 the blue Electro-Tap to tap into pin 20 (GND, white w/ black tracer). Conduct a continuity check, to determine
 good connection.
 Finally, please ensure that an external device or dummy jack is used to enable to the AUX.


                                                                                      DENSO Sales Canada, Inc.
                                                                                         Aftermarket Department
8. INSTALLATION: Basic

                                           NOTE
                     AUX & STEERING
        K3              SW W/H         Connect the aux and steering switch
                                       W/H to connector K3. Ensure that the
                                       receptacle (female) is connected to
                                       K3. Use 2 foams to cover the
                                       receptacle connector of aux and
 FOAM X 2                              steering SW W/H. Please note that
                                       this wire harness must be ordered
                                       through the Toyota Parts
                                       Department.




                                       Next, route the shielded, 5 pin (brown w/ gray
                                       dot) and the audio upgrade wire harnesses
   INSTRUMENT
      PANEL
                                       towards the glove compartment area. Please
 REINFORCEMENT                         review the photo on the left. Ensure that these
                                       3 wire harnesses are routed along the
                                       instrument panel reinforcement.
                                       Use TWO 11” cable ties to fasten all 3 wire
                                       harnesses to the reinforcement.

                                          : 11” CABLE TIE u 2
                                        Tools: Side Cutter

       GLOVE COMPARTMENT AREA




       GLOVE COMPARTMENT AREA
                                       Locate the space as indicated by the
                                       red box, behind the glove
                                       compartment area. See picture. This
                                       is the mounting location of the
                                       external amplifier.
      EXISTING
       HOLE                            Please note that the external
                                       amplifier must be ordered through
                                       the Toyota Parts Department.
                                       Locate the existing hole, as
                           AMPLIFIER   indicated by the arrow on the
                           LOCATION    picture.                      37
8. INSTALLATION: Basic

               EXISTING       MARK     Using a straight edge ruler, measure
                HOLE          HERE!    approximately 35 mm to the right, from
                                       the existing hole. Mark this point, as
                                       indicted on the picture.

                    35 mm              Tools: Straight Edge Ruler




                               DRILL   Use a #10 drill bit to drill through the
  REINFORCEMENT                HERE!   metal reinforcement.
                                       Also, use 1 foam provided in the CAR-
                                       NAVI kit, as indicted in the photo.

                                       Tools: Drill (electrical/pneumatic), #10
                                             Drill Bit
                      FOAM
                      HERE!




                                       Remove the existing nut, as
                                       indicated by the photo. Afterwards,
                                       please re-use this nut to mount the
                                       amplifier bracket.

                                       Tools: Ratchet ¼” Drive, 10mm socket
                                             (¼”)
    EXISTING
      NUT




                                                                          38
8. INSTALLATION: Basic

                         EXTERNAL              NOTE
EXISTING                 AMPLIFIER
  NUT                                     Loosely install the amplifier bracket to the external
                                          amplifier and to the existing bolt, located where the
                                          existing nut was temporarily removed.
                                          Please note that the amplifier bracket may not align
                                          properly. Slight bend in the amplifier bracket may
 AMPLIFIER                                be required.
 BRACKET                                  Use the bolt and nut that came with the bracket kit,
                                          to mount it to the amplifier.
                                          The Bracket kit must be ordered through the
                                          Toyota Parts Department.
 BOLT & NUT
(BRACKET KIT)                             Tools: Ratchet ¼” Drive, 10mm socket
                                                (¼”), 10mm wrench


                  REINFORCEMENT    TAP    Use the tap screw provided in the
                                  SCREW   bracket kit, to mount the top part of the
                                          amplifier to the reinforcement.

                                          Tools: Long Tip Screwdriver (Slot Type),
                                                Ratchet ¼” Drive, 7/16” or 11mm
                                                socket (¼”)
 EXTERNAL
 AMPLIFIER




                                          Once the external amplifier has been
                                          installed, please ensure that the
                                          amplifier has been mounted firmly
                                          into place. Please review the photo
                                          on the left.
           EXTERNAL
           AMPLIFIER




                                                                                      39
8. INSTALLATION: Basic
                                  Connect the REVERSE Signal:
                                  Locate connector AJ2 (RH Kick Panel) and find pin
                                  3. Please see the photo on the left for the location
                                  and below for the connector view. Once pin 3 is
 RIGHT KICK                       located, you will notice that the wire is coloured
   PANEL                          BLUE (REVERSE SIGNAL from the BACKUP
   AREA              AJ2          RELAY). For further information, please consult
                                  with the TOYOTA Tundra Electrical Wiring
                                  Diagram.

                                                         AJ2               Pin 3




                                       NOTE
  REVERSE
   SIGNAL                         Once the REVERSE signal wire (brown w/ grey dot) has
                                  been tapped (blue Electro-Tap), use ONE Foam provided
    WIRE                          in the CAR-NAVI kit, to wrap the electro-tap. Re-connect
                                  connector AJ2 to the junction connector.

                                  Please ensure that the REVERSE wire has been
                                  properly latched. Use the digital tester, to ensure that
                                  the connection is good.
   RUN-
   RUN-WIRE
                           BASE
   SECTION                        Tools: Pliers, Digital Tester




              AU15                The illustration on the left shows the
                                  front view of connectors AU15 and
                                  AU16. These 2 connectors are part
                                  of the audio upgrade W/H. Ensure
                                  that these 2 connectors reach the
                                  external amplifier’s 2 mating
                                  connectors.
              AU16                Next, locate connector AU15 (24 pin
                                  connector).


                                                                                40
8. INSTALLATION: Basic
               AU15                              NOTE
       (AUDIO UPGRADE W/H)                  Connect the shielded wire end with 2 wires (red,
                                            green), to connector AU15. Please review the
                                            connector illustration to the left for the wire
                                            connection and chart below.
                                            Ensure that the secondary lock is loosened.
                                            After ALL wires are in place, ensure that the
                                            secondary lock is locked once again.

                                             PIN LOCATION      WIRE COLOUR           SIGNAL

                                                   22             GREEN               INT-

                                                   23               RED               INT+
                                     RED
                             GREEN


   EXTERNAL                                 Connect AU15 and AU16, to the
   AMPLIFIER                                corresponding mating connectors of
                      AU16
                                            the external amplifier.




                                     AU15




Following procedures are only applicable for installation of the
Bluetooth/Voice Recognition and/or Rear Camera OPTIONS.
Please proceed to the necessary procedures.
If these procedures are not required, please skip to the GPS
ANTENNA INSTALLATION.



                                                                                      41
8. INSTALLATION: Bluetooth & Voice Recognition
                                             Route connector T13 from MIC+Talk Switch
                                             W/H (with “M” label), from the Roof Console
                     ROOF HEADLINING
                        ASSEMBLY
                                             Box Assembly. Please see below for T13
                                             connector view. Ensure to route the harness
                                             between the roof and the lining. Also, use 2
                      WIRE                   foams to fasten the wire harness between the
                    HARNESS                  lining and the roof.

                                                               T13
                              T13




                              ROOF CONSOLE                  (Front View)
             FOAM               BOX AREA




             FRONT PILLAR                    Please continue to route the wire
                 (LH)                        harness along the front pillar (LH).
                                WIRE
                                             Please review the photo. Ensure that
                              HARNESS        the wire harness is passed though the
                                             2 clips. Use ONE cable tie to fasten
                                             the wire harness to the vehicle’s wire
                                             harness.
        ROU
           TE                                  :4” CABLE TIE u 1
                      CLIPS                  Tools: Side Cutter




                                             Continue to route the wire harness
                                             behind the side panel (LH). Next,
                                             continue to route the wire harness as
                                 WIRE
                               HARNESS       shown. Use ONE cable tie to fasten
                                             the wire harness with the vehicle wire
                                             harness.

                                               :4” CABLE TIE u 1
                                             Tools: Side Cutter
  DRIVER’
  DRIVER’S
  DRIVER’S
    SIDE
    SIDE
                                                                                  42
8. INSTALLATION: Bluetooth & Voice Recognition
                                        Continue to route the wire harness, behind the
                                        metal shield (underneath the steering column).
                                        Use 2 foams to wrap the wire harness to the
                                        metal shield (see below). Next, continue to
                                        route the wire harness upwards, towards the
                                        radio receiver area.
                     FOAM


                                                   FOAM

                                                                           WIRE
                                                                         HARNESS
                                         METAL
                                         SHIELD
                            METAL
   WIRE                     SHIELD
 HARNESS                                            << SIDE VIEW >>



     HEATER TO                          Route the wire harness towards the heater to
     REGISTER                           register duct (LH). Use ONE 4” cable tie to
      DUCT (LH)                         fasten to the vehicle wire harness, as shown.

                                          :4” CABLE TIE u 1
                                        Tools: Side Cutter



     WIRE
   HARNESS




                                        Insert the microphone assembly inside
                                        the vacant square area (shown in red).
                                        Please review the photo. Insert the clip
           ROOF CONSOLE BOX             from the connector end of the
                                        microphone assembly, into the existing
 MICROPHONE                             hole on the tab.
  ASSEMBLY                  CONNECTOR




                      TAB


         << UNDERSIDE SHOWN >>
                                                                              43
8. INSTALLATION: Bluetooth & Voice Recognition

                                           Next, re-install the Roof Console
       ROOF CONSOLE BOX                    Box. Remember to re-connect all
                                           connectors, including the
                                           microphone assembly to T13.




   TALK
                        TALK SWITCH WIRE
                                           Use ONLY the talk switch wire
  SWITCH
                            HARNESS        harness, for this installation. Please
                                           note that the WHITE connector of the
                                           talk switch W/H will not be used. The
                                           BLACK connector of the talk switch
                               WHITE       W/H will be used.
                             CONNECTOR




                            BLACK
                          CONNECTOR




     TALK SWITCH                           Connect the black connector from the
         W/H                               talk switch W/H to the MIC+Talk
                                           switch W/H. Install the excess wire
                                           harnesses from both the MIC+talk
                                           switch and talk switch W/Hs, behind
                                           the original radio receiver area.




            MIC+TALK
           SWITCH W/H
                                                                           44
8. INSTALLATION: Bluetooth & Voice Recognition

                                         Ensure that the Talk Switch is routed
                                         through the opening, behind the
                                         Instrument Cluster as indicated in the
                                         photo.
          ROUTE
                     RADIO RECEIVER
                     ASSEMBLY AREA




 INSTRUMENT                TALK SWITCH
   CLUSTER                  W/H (TALK
 FINISH PANEL                SWITCH)




                                         Do not remove the liner underneath
             TALK
                                         the Talk Switch. Leave it loose until
            SWITCH
                                         instructed to do so.




Following procedures are only applicable for the full
installation of the Rear Camera OPTION. Please proceed to the
necessary procedures. Please ensure that the Camera Kit has
been fully installed, prior to proceeding to the Rear Camera
installation, of this manual.



                                                                          45
8. INSTALLATION: Rear Camera
                                       Behind the box door sub-assembly
           SUB-
  BOX DOOR SUB-                        area, please locate the male connector
  ASSEMBLY AREA                        of JK1. Please review the photo. See
                                       below for connector view of the male
                                       connector. Once located, please
                                       remove.

                                                  JK1 (MALE)
                  JK1




                                                 <<FRONT VIEW>>


                               JK1     Next, connect JK1 (male) to the
                            (FEMALE)   corresponding mating connector
    JK1                                (female) of the Camera Adapter W/H.
  (MALE)                               Locate the male connector (similar
                                       appearance of JK1 male) and connect
                                       to JK1 female. Please review photo.




                          CAMERA
                        ADAPTER W/H




                                       Route the bare terminals from the
                                       Camera Adapter W/H, towards the
                                       radio receiver area.
           RO
            UT
              E




                     CAMERA
                   ADAPTER W/H
                                                                      46
8. INSTALLATION: Rear Camera
                         Connect the bare terminals from the camera adapter
                         W/H, to the MIC+talk switch W/H (24 pin connector).
                         Insert the bare terminals from the camera adapter W/H, to
                         the MIC+Talk switch W/H. Please see chart on the left.
                         Once completed, engage the secondary lock.

                              MIC+TALK SWITCH WIRE HARNESS




                                             (Front View)        INSERT
                                                                LOCATION




                                                                       47
9. GPS ANTENNA INSTALLATION

  HEATER TO             <<RIGHT SIDE>>    The GPS Antenna and bracket will be
REGISTER DUCT                             mounted on top of the right side
                                          Heater to register Duct.




                         GPS ANTENNA
                        MOUNTED HERE!



          RADIO RECEIVER AREA




   DOUBLE                   GPS ANTENNA   Peel off one side of the Double Coated Tape,
 COATED TAPE                  BRACKET     and apply on the underside of the GPS
                                          Antenna Bracket (shown on the photo).

                                                        GPS ANTENNA
                                                          BRACKET
                                                                             DOUBLE
                                                                           COATED TAPE
                                             SHORT




                                                           LENGTH

                                                      << SIDE VIEW >>



                                                 NOTE
                                          Peel off the liner of the Double Coated
                              GPS         Tape and mount the tape side, on top
                            BRACKET       of the Heater to Register Duct (shown
                                          on the photo). Use TWO trim screws
                                          provided in the CAR-NAVI kit, to
                                          secure the GPS Antenna bracket to
                                          the duct. Please do NOT drop the
                TRIM
                                          trim screws! Do NOT over tighten
               SCREWS
                                          the trim screws! Please review the
                          RIGHT SIDE      following photo below.
                             DUCT                                              48
9. GPS ANTENNA INSTALLATION
                                     As you will notice in the CAR-NAVI kit, the
                                     GPS Antenna wiring is excessively long.
                                     Wrap the GPS Antenna wiring with your
                                     hands, and use THREE 4” cable ties to tie
                                     it down (shown on the photo to the left).
                  CONNECTOR          Ensure there is plenty of length on the
                                     GPS Antenna and connector ends.

                            GPS         : 4” CABLE TIE u 3
                          ANTENNA
                                     Tools: Side Cutter




         INSTRUMENT                  Mount the excessive GPS Antenna
            PANEL
       REINFORCEMENT
                                     wiring on to the Instrument Panel
                                     Reinforcement. Use TWO 11” cable
                                     ties as shown on the photo on the left.

                                       : 11” CABLE TIE u 2
                                     Tools: Side Cutter

       GPS ANTENNA WIRE
           (EXCESS)

  RADIO RECEIVER ASSEMBLY AREA




                             GPS     Route the GPS Antenna to the top of
                           ANTENNA   the GPS bracket. Please note that the
                                     underside of the GPS Antenna has a
   GPS                               magnet, which will be attracted to the
                            GPS      bracket. Note that the GPS antenna is
 ANTENNA
                          BRACKET
   WIRE                              mounted on the top side of the
                                     bracket. Use ONE Foam provided in
                                     the CAR-NAVI kit, to fasten the GPS
                              FOAM
                                     Antenna Wire to the side of the
                                     register.

                                                                        49
9. GPS ANTENNA INSTALLATION
                                                     Connect the appropriate connectors
  UP
       <<REAR VIEW OF THE AVN-S DISPLAY UNIT>>
                          AVN-                       into the back of the AVN-S Display
                                     RADIO ANTENNA   Unit. Please review the photo on the
  20 PIN CONNECTOR                    CONNECTOR      left. Ensure that ALL applicable
(AUDIO UPGRADE W/H)
                                                     connectors are connected to the
                        5 PIN W/H                    back of the AVN-S unit.


                                                             ESD


                                     AUX/STEERING
24 PIN CONNECTOR         GPS            SW W/H
(MIC+TALK SW W/H)      ANTENNA




           NAVIGATION SYSTEM (WITH                     NOTE
             AVN-
             AVN-S DISPLAY UNIT)
                                                     Once the Navigation System (with
                                                     AVN-S Display Unit) has been re-
                                                     connected, re-connect the negative
                                                     terminal to the negative side of the car
                                                     battery. Do not tighten to torque
                                                     specifications! Mount the Navigation
                                                     System back into its original location.




                                                                                      50
10. OPERATION CHECK

                      Turn the key to the ACC or ON position. Since
                      there is no Map DVD in the AVN-S Display
                      Unit, the unit will automatically retract. Since
                      the Map DVD is NOT provided in the CAR-
                      NAVI kit, ensure that it is ordered through
                      the Toyota Parts Department. When
                      encountering problems at any time during the
                      Operation Check, please consult with the
                      latest TOYOTA Tundra Repair Manual.




                      Insert the latest version of the DVD
                      Map into the MAP slot. The AVN-S
                      Display portion will automatically
                      return, in the upright position. NOTE:
                      Please ensure that the DVD Map is
                      inserted into the MAP slot.

        INSERT
         HERE!




                          NOTE
                      Notice that the system is loading.
                      During this time, please do NOT
                      turn off the power.




                                                              51
10. OPERATION CHECK

                           NOTE
                      Select the appropriate language
                      selection (English/French/Spanish).
                      Please note that the AVN-S Display
                      Unit features a TOUCH SCREEN
                      (press firmly on the screen).




                      START the vehicle, then move the vehicle
                      outside of the garage. Once outside, ensure
                      that there are no tall buildings obstructing
                      the GPS signal to the vehicle. Go to the
                      MAP screen shown on the photo on the left
                      (press the MAP/VOICE button). Wait 8 to 10
                      seconds before the GPS signal is picked up.
                      This is indicated by the GPS symbol.
    GPS               For a quicker calibration, please press the
  SYMBOL              MENU button and go into the SETUP menu.
                      Next, go to page 3/3 and select
                      CALIBRATION. Go into
                      POSITION/DIRECTION and calibrate
                      manually here.



                      There are TWO methods to enter the
                      Diagnostic Mode:
                      Method #1: Make sure that the vehicle is
                      stopped (speed=0 km/h). Go into the
                      DIAGNOSTIC menu by pressing the Display
                      button on the bezel. Alternately touch the
                      upper and lower areas at the left side of the
           TOUCH      screen (shown on the photo) 3 times. This will
            HERE      activate the diagnostic system of the AVN-S
                      unit.



                                                            52
10. OPERATION CHECK
                                  There are TWO methods to enter the
                                  Diagnostic Mode:
                                  Method #2: Make sure that the vehicle is
                                  stopped (speed=0 km/h). Go into the
                                  DIAGNOSTIC menu by pressing and holding
                 (OFF-TAIL) u 3
                 (OFF-            the INFO button on the bezel, then alternately
                                  operate the light control switch: OFF-TAIL,
                                  OFF-TAIL, OFF-TAIL (total of 3 times). This
                LIGHT CONTROL     will activate the diagnostic system of the AVN-
                    SWITCH        S unit.




                                  Wait 2 to 4 seconds, before the results of the
                                  System Check Mode. If the message indicates
                                  OK, the AVN-S Display Unit and the DSP-
                                  Amplifier (DSP-AMP) are good. Next, check
                                  the results of the LAN Monitor (LAN Mon). If
                                  the display unit indicates an error (CHK),
                                  please consult with the latest TOYOTA
                                  Tundra Repair Manual.
                                  The Rear Seat Entertainment (Rr-TV) icon
  LAN MONITOR
                                  is not available on this model.




                                      NOTE
                                  If the message indicates OK, the AVN-S
                                  Display Unit, and DSP-Amplifier (DSP-AMP)
                                  are good. Proceed to the Menu screen (press
                                  top right hand corner of display). If the display
                                  unit indicates an error (CHK), please
                                  consult with the latest TOYOTA Tundra
                                  Repair Manual. Please note that when
                                  installing the CAR-NAVI kit without
                                  removing negative terminal of the battery,
                                  can cause the LAN Monitor circuitry, to log
                                  LAN Monitor codes.
                                  The Rear Seat Entertainment (Rr-TV) icon
                                                                    53
                                  is not available on this model.
    DISPLAY CHECK
        MODE




                                                         1
                                                         2
                                                         3
                                                         4




1                                                            2




    Press each COLOUR chart. The entire screen                   Ensure that each location touched on the
    will change to the selected colour or stripe.                AVN-S Display, does activate the pointer.
    Ensure that each colour name does
    correspond to each colour on the bar. Ensure
    that there is no visible pixel of different colour
    on the display. Please use this Colour Bar
    Check mode and compare with the NAVI
    Colour Bar Check mode.




3                                                            4




    Ensure that each push and rotary switches                    Ensure that Reverse, Speed and Tail signals
    are being displayed, once they are pushed or                 are functioning properly. NOTE:The Park Brake
    turned.                                                      (PKB) signal is NOT required for the Vehicle
                                                                 Signal Check (Default: OFF).
                                                                                                             54
NAVIGATION CHECK
      MODE




                                             1               5
                                             2               6
                                             3
                                             4               7




1                                                                2




    The Measurement Status must read 3D (3 dimensions),              Ensure that Vehicle and Sensor Signals are
    before the vehicle can pass initial inspection. Always           functioning properly. To test the REV signal, shift
    ensure that at least three Ps (positioning) and one T            the transmission to reverse. The SPD signal must
    (tracking) is available in the STS (status) column.              be observed during a test run of the vehicle.
    NOTE: Ensure that there are no objects, blocking the             Please use the combination meter’s readings for
    reception of the GPS Antenna. Also, ensure that the              comparison or the TOYOTA Diagnostic Hand
    vehicle is outside of the garage.                                Tool, during a test run. Gyro Voltage can be
                                                                     tested during a turn of the vehicle (left/right). The
                                                                     Relative Bearing is defaulted to ZERO degrees. If
                                                                     not, please RESET.


3                                                                4




       Ensure that each colour name does correspond                  This function is not available.
       to each colour on the bar. Please use this NAVI
       Colour Bar Check mode and compare with the
       Colour Bar Check Mode.
                                                                                                                      55
NAVIGATION CHECK
   MODE cont..




                                           1             5
                                           2             6
                                           3
                                           4             7




5                                                            6



                                                                                D




                                                                                        A      B      C

    Navi Information lists the manufacture of the AVN
    Display Unit, as well as the version number of the                     Switch               Description
    AVN Display Unit. Disc Information lists the                                        Record up to 5 second
    version number of the Map DVD.                                                      sample. During recording,
                                                                  A        Record       the REC text will show to
                                                                                        the right of the Play Back
                                                                                        switch.

                                                                                        Stops recording the
                                                                  B         Stop
                                                                                        sample.

7                                                                 C      Play Back      Plays the recorded sample.

                                                                         Mic. Input     Indicates the microphone
                                                                  D
                                                                           Level        level input.

                                                                 When voice is inputted into the microphone, check
                                                                 that the microphone input level meter changes,
                                                                 based on the voice input. Push the recording
                                                                 switch and perform voice recording. Check that the
                                                                 recording indicator remains on while recording and
                                                                 that the recorded voice is played normally.
    This screen displays the diagnostic code history
    of the DVD player (Map DVD).
    Code 01: Cannot Recognize
    Code 03: Cannot Read
                                                                                                              56
10. OPERATION CHECK: VOICE RECOGNITION

                       Remove the liner from the back of the
         TALK          talk switch and mount as indicated by
        SWITCH
                       the photo.
                       Press the Talk Switch, to initiate the
                       Voice Recognition function.




                           NOTE
                       After the Talk Switch has been pressed, a
                       voice command will ask the user to say a
                       command, after the beep. Please say
                       “HELP”. This will list useful voice recognition
                       commands. Please ensure that you sit back
                       and talk clearly to the MIC, located above
                       of the Personal Light Assembly. DO NOT
                       TALK DIRECTLY INTO THE MIC! Conduct
                       more testing by speaking other listed voice
                       commands, in the HELP menu.




                       If the system could not detect your voice
                       command, please ensure that you talk clearly
                       to the MIC. Also, ensure that all connection
                       have been made to the back of the AVN-S
                       unit. Ensure that the interior cabin noise is
                       reduced to minimum. For your reference,
                       please visit the Diagnostic Mode and re-check
                       the Mic & Voice Recognition Check.




                                                              57
10. OPERATION CHECK: AUX PORT

                        To test the AUX port, use a dummy
                        mini jack to simulate an external
                        device connection. If possible, plug an
                        external device and conduct sound
                        testing.

             AUX PORT




                        Once the dummy mini jack is in place,
                        press the DISC/AUX button on the
                        AVN-S unit. A pop-up message will
                        appear on the top of the display
                        screen. If no AUX message appears,
                        ensure that the AUX connector has
                        been properly connected at the back
                        of the AVN-S unit.




                                                        58
10. OPERATION CHECK: REAR CAMERA

                       Once the transmission has been
                       shifted to the REVERSE position, the
                       AVN will display the camera’s rear
                       image behind the vehicle.
                       If no image appears, please ensure
                       that all wire harnesses are properly
                       connected.




                                                       59
11. RE-INSTALLATION

   CAUTION

For the RE-INSTALLATION section, please follow the
DISASSEMBLY section in reverse order. While re-
installing original parts, ensure that there is no biting
into the vehicle harness, and damage to the original
parts.



              NEGATIVE            Re-connect the vehicle’s
              TERMINAL            negative battery cable. Tighten
                                  with 4.0 N•m [41 kgf•cm, 36
                                  lbf•in].

                                  Tools: Ratchet ¼” Drive, 10mm Socket
                                        (¼”)
   FRONT




                    BATTERY




                                                               60
12. RE-INITIALIZING
                      <Power Window>
                      Ensure that the key is in the ON position. Push
                      down on the power window switch (Driver’s
                      Side) and lower the window half way. Next pull
                      up the switch until the window closes, and hold
                      the switch for a second. Ensure that the power
                      window automatically opens and closes after
                      the re-initializing process.




                      <Moon Roof>
                      Ensure that the key is in the ON position. Push
                      and hold the switch on the TILT UP side, until
                      the moon roof tilts to the upward position and
                      then slightly tilts down automatically. Also
                      make sure that the moon Roof automatically
                      opens and closes after the re-initialization
                      process.




                      Enter the CAR-NAVI voice volume setting by
                      pressing the MENU button located on the
                      bezel. Next, enter VOLUME menu then select
                      the desired CAR-NAVI Voice setting. If no
                      CAR-NAVI voice is heard, please check all
                      connections.
                      Please note in the previous installation,
                      that if the shielded wire has not been
                      properly installed, no voice guidance can
                      be heard. If this is the case, ensure that
                      you return to those installation procedure.


                                                             61
12. RE-INITIALIZING
                              Please adjust the clock setting on the Clock
POWER/VOLUME
                              Assembly (where applicable). Re-set the original
                              radio stations (FM1, FM2 and AM). To enter the
                              radio station screen, turn the audio function on by
                              pressing the left knob (power/volume switch) and
                              then press the AUDIO button on the bezel. Also,
                              check if the AUDIO CD Player is functioning
                              properly.




                      AUDIO




                                                                          62
13. TROUBLESHOOTING HINTS




                            63
13. TROUBLESHOOTING HINTS




                            64
    14. DIAGNOSTIC CHART
‰




‰




‰




‰




                           65
    14. DIAGNOSTIC CHART
‰




‰




                           66
    14. DIAGNOSTIC CHART
‰




‰




‰




                           67
    14. DIAGNOSTIC CHART
‰




                           68
    14. DIAGNOSTIC CHART
‰




                           69
Published: February 2008

    [Duplication prohibited without permission]




SUPERVISION: Toyota Canada Inc.

EDITING: DENSO Sales Canada, Inc.

				
DOCUMENT INFO
Shared By:
Categories:
Tags:
Stats:
views:144
posted:3/23/2011
language:English
pages:70