VIEWS: 11 PAGES: 1 POSTED ON: 3/20/2011
5.Attach the plastic needle to 6.Deflate on the position of Instruction Installation Steps the syringe. the colour you want to refill by using the syringe provided. How to shield and delete printer 1 Fixing plate installation messages Eco-Ink Refill System 1.Combine the arc part on the fixing 2.Press the fixing plate vertically till it The printer may display messages showing " empty cartridge" or "used plate with that on the cartridge. reaches the face plate of the Canon cartridges" as the cartridge is refilled, please press the "stop" button on cartridge. the printer and hold for 5 seconds to shield and delete the messages. Please read the instruction carefully ,follow the procedures and be aware of the signs on the machine. 7.Pull the syringe pole up to the 30ml mark and hold for 4-5 seconds to get the ! Warning ① ② Notes:Same fixing plate for either black and white cartridges, please drill on the pressure balanced. Notes:please insert the 1.To prevent ink leakage please respective position indicated by the fix plate. ! syringe down to the bottom. 5" insert the syringe to deflate 8.Release the syringe pole, before second usage. 2 Drill on the cartridge a refill is completed when √ × 30 2.Do not press the injection! the syringe pole reaches 1.Remove the protection cap 2.Put the cartridge upside down to the bottom. on the drill bit. get the print-head faces up. Parts list and pictures Eco-Refill FAQ and trouble shooting Drill Bit Fixing plate Problems Please confirm What to do. Eco-Refill Syringe 3.Drill on the position indicated by 4.Remove the fixing plate by release the fixing plate on a clockwise the buckle and keep the plate for Instructions sequence. See the parts list on Please contact the next refill. Missing Parts Plastic Needle the instruction distributor Tissue Fixing Plate tissue 1. Damage on package 9.Please follow steps 2-8 10.Seal the stopper after use. for refills for each colour. and the product Syringe(30ml) Ink leakage on during transportation Please contact the Eco-Refill distributor 2. If no package Plastic Needle Drill Bit Instructions damage Leakage on Please replace Before Use Notes:For colour cartridges, please drill on the area indicated by the fixing plate. As Cartridge Ink concreted the cartridge shown on the picture above. To prevent cross contamination, please clean the coloured ! Tips:This product is for use with used out inkjet cartridges with drill bit after every drilling. print-head,do please follow the procedures in use.The actual times 1. Any leakage on the 1. Please clean the Leakage on refilled cartridge residual ink on the of refill is totally depended on the quality of the cartridge, 3 Place the cartridge into the Eco-refill kit cartridge during 2. Too many refill cartridge more times with higher quality cartridges and vice versa. print process causes the sponge 2: Please replace the 1.Open the lid 2.Remove the plastic stoppers. structure saturated cartridge ! If the printer displays caution message when using refilled cartridges,please shield the message and the printer will still work Notes:For black ink, please refill twice if the ink are only 1/4 left, so as to normally.Please see the last part of the instruction for specific steps. provide sufficient ink supply. 1. Non-OEM cartridges 1. Please use OEM For black deflate at the hole assigned.(as shown in figure ) with bad quality print- ! Same procedures for cartridges with different capacity. head cartridges If the syringe is coloured during refill, please wash it so as to prevent cross 2. Please replace the contamination. 2. Ink concreted or Inferior print cartridge electric circuit damage ! Cautions 4 Procedures after refill quality 3. Use incompatible ink 3: Please use Ninestar manufactured inks 1.Please make sure the cartridge works properly. in last refill 4: Please replace the 2.To prevent ink leakage, do always plug the stoppers after use. 4. Cartridge reaches 1.Open the lid and pull out the 2.Wipe out the residual inks cartridge the end of its life cycle 3.To prevent needle damage, do always close the lid. cartridge vertically and place and then you are ready to 4.For black ink, please refill twice if the ink are only 1/4 left, so as to it onto a piece of tissue. perform print test. provide sufficient ink supply. 1. Please replace the 3.Make sure the print-head faces 4.Close the lid and make sure the 5.The product is designed on negative pressure theory, so never press up and insert it vertically into lid is perfectly buckled. 1. Colour mixed inside cartridge the syringe pole to prevent spill of ink. Eco-refill. the cartridge 2. Please print serval 6.please deflate the kit by using the plastic needle before every usage. 2. Colour mixed during pieces of paper or 7.Please clean the print head after each refill. print head cleaning clean the print-head 8.The syringe pole might not reach back to the buttom after deflating, Colour difference 3. Software problems 3. Check the setting on any position reached below 5ml mark is within normal range 4. A slight difference software and monitor compare with the 4. Adjust the colour 9.Do please place the kit out of reach of children.If carelessly OEM ink configuration of the swallowed, please consult the doctor immediately. Notes:If the printer appears offline, please clean the print head so as to remove bubbles on the nozzle. printer, please see 10.Avoid direct sunlight. Please storage under natural temperature. printer manual 11.Same procedure for either large or small capacity cartridges.
Pages to are hidden for
"Instruction"Please download to view full document