SJ00 Section2

Document Sample
SJ00 Section2 Powered By Docstoc
					                                               SECTION 2
                                               OPERATION
OPERATOR QUALIFICATIONS                                      ELECTRICAL PANEL - This control station is located in
Only trained and authorized persons should use this work     the Hydraulic/Electric Tray. It contains the following
platform. Safe use of this work platform requires the        controls:
operator to understand the limitations and warnings,
operating procedures and operator’s responsibility for       1. UP/DOWN TOGGLE SWITCH, or BUTTONS -
maintenance.        Accordingly, the operator MUST           Selecting and holding this toggle-type switch to “UP”
understand and be familiar with this operating manual, its   position, or pressing the “UP” button will raise platform to
warnings and instructions and ALL warnings and               desired height. Release switch/button to stop. Selecting



                                                                                                                             2
instructions on the work platform. Operator also MUST be     and holding switch to “DOWN” position, or pressing
familiar with employer’s work rules and related              “DOWN” button will lower platform to desired height.
government regulations and be able to demonstrate his/       Release switch/button to stop.
her ability to understand and operate THIS make and
model work platform in the presence of a qualified person.   2. BUZZER ALARM - This audible pulse alarm sounds
                                                             when platform is being lowered.
OPERATING CONTROL IDENTIFICATION                             3. HOURMETER - Activated when the pump/motors runs,
The following descriptions are for identification and        this gauge measures work platform operating time.
locating purposes only. A qualified operator MUST read
and completely understand “SECTION 2, OPERATION”             4. 15 AMP CIRCUIT BREAKER RESETS, or FUSES - In
in this manual before operating any control on the work      the event of a power overload or positive circuit grounding,
platform.                                                    circuit breaker will pop out or fuse will blow. Make the
                                                             necessary corrections, then depress the push-button to
Both standard and optional controls for this work platform   reset or replace the fuse.
are identified in this section. Therefore, some controls
may be included that are not furnished on your work          Emergency Power Disconnect Switch
platform.                                                          (If Equipped)

OPERATING CONTROLS
Base Controls - Electrical
Electrical Panel

         2                  3


                                                                 1


   1



                                                                Figure 2-2. Emergency Battery Disconnect Switch

                                                             1. EMERGENCY BATTERY DISCONNECT SWITCH

               Figure 2-1. Electrical Panel     4
                                                             1. EMERGENCY BATTERY DISCONNECT SWITCH,
                                                             (If Equipped) - Located at the rear of the hydraulic/electric
1. UP/DOWN TOGGLE SWITCH, or BUTTONS                         tray this switch, when in “OFF” position, disconnects
2. BUZZER ALARM                                              power to all control circuits. Switch MUST be in “ON”
3. HOURMETER                                                 position to operate any control circuit.
4. 15 AMP CIRCUIT BREAKER RESETS, or FUSES


SJ00 Series 104282AA                                                                               SECTION 2, Page 1

toc     1      3      4     5      6
Base Controls - Hydraulic                                      Base Controls - Hydraulic/Manual
Emergency Lowering Valve                                       Parking Brake
(Machines with Velocity Fuses)


                                                      1
                                                                                                                      1




                                                                               Figure 2-5. Parking Brake

         Figure 2-3. Emergency Lowering Valve                  1. PARKING BRAKE

1. EMERGENCY LOWERING VALVE (Rotary-Type)                      1. PARKING BRAKE - A pin retracted and extended by
                                                               a single-acting hydraulic cylinder engages the brake disc
1. EMERGENCY LOWERING VALVE (Rotary-Type) -                    on the rear wheel when lifting, lowering or parking. The pin
Located in the hydraulic/electric tray, this valve allows      disengages when driving. The brake MUST be manually
platform lowering in the event of an electrical system         disengaged for towing, pushing or winching. This requires
failure. Turning the valve knob counterclockwise allows        a special procedure as follows:
the platform to gradually lower. Valve MUST be fully
closed (clockwise) to restore normal operation.
                                                                                      WARNING
Free-Wheeling Valve
             1                                                 DO NOT manually disengage the parking brake(s) if the
                                                               work platform is on a slope.

                                                               •       Make sure that the work platform is on level
                                                                       ground.

                                                               •       For Left-Hand Brake: Using a 3/4" wrench,
                                                                       rotate the lockout block on the brake pin 90°
                                                                       clockwise.


                                                                                         NOTE
            Figure 2-4. Free-Wheeling Valve                    The parking brake(s) will reset automatically when the
                                                               work platform is driven. Inspect to be sure brake is fully
1. FREE-WHEELING VALVE                                         functional and fully engaged when stopped.
1. FREE-WHEELING VALVE - The free-wheeling valve is
located at the rear of the base on the rear manifold.
Turning the valve knob counterclockwise to a fully opened
position allows fluid to flow through the wheel motors, thus
providing “free-wheeling” so that the work platform can be
pushed or towed without damaging the wheel motors.
When towing, DO NOT exceed 2 mph. Valve MUST be
closed tightly (clockwise) for normal operation.




SECTION 2, Page 2                                                                              SJ00 Series 104282AA
Safety Bar                                                 Platform Controls
                                                           Operator’s Control Box



                                                              3


                                                1
                                                                                                               2




                                                                                                                   1


                Figure 2-6. Safety Bar

1. SAFETY BAR

1. SAFETY BAR - Designed to support the scissors
assembly (when properly positioned), the safety bar
MUST be used for inspection and performing
maintenance or repairs within the scissors assembly with
the platform raised. To use the safety bar, follow the                      5                 4
procedure on the safety bar label on the base.

                    DANGER                                            Figure 2-7. Operator’s Control Box
              CRUSHING HAZARD                              1. LIFT/OFF/DRIVE SELECT KEY SWITCH
                                                           2. UP/DOWN SELECT SWITCH
DO NOT reach through scissor assembly without the          3. DRIVE STEER CONTROLLER
safety bar properly positioned. Failure to avoid this      4. EMERGENCY STOP BUTTON
hazard will result in death or serious injury!             5. LIFT ENABLE PUSH-BUTTON (Later models)


                                                           OPERATOR’S CONTROL BOX - This metal control
                                                           station is mounted on the railing at the right front of the
                                                           platform. It contains the following controls:

                                                           1. LIFT/OFF/DRIVE SELECT KEY SWITCH - Key to
                                                           “LIFT” position energizes the lift circuit. Key to “OFF”
                                                           position disconnects power to control circuit in control
                                                           box. Key to “DRIVE” position energizes the drive/steer
                                                           circuit.

                                                           2. UP/DOWN SELECTOR SWITCH - To raise the
                                                           platform, key to “LIFT” position, then rotate selector
                                                           switch to “ UP “ position until desired height is reached.
                                                           Release switch to stop. To lower the platform, key to
                                                           “LIFT” position, then rotate selector switch to “ DOWN“
                                                           position until desired height is reached. Release switch
                                                           to stop. A warning alarm will sound while lowering.


SJ00 Series 104282AA                                                                            SECTION 2, Page 3
3. DRIVE/STEER CONTROLLER - A one-hand toggle-                 Powered Extension Platform Control Box
type lever to control three-speed drive and steer motion. It
is a “dead-man” control which returns to neutral and locks
when released. To drive forward, key to “DRIVE” position,
then lift lock ring and push handle forward to desired
speed. Release to stop. To drive in reverse, key to
“DRIVE” position, then lift lock ring and pull handle             1
backwards to desired speed. Release to stop. To steer,
depress the side of the rocker switch on top of the
controller handle in the direction you wish to steer.

4. EMERGENCY STOP BUTTON - When struck, this red
push-button switch disconnects power to the platform                  2
control circuit. In the event of an emergency or at work
platform shut down, push the button in. To restore power
to the platform controls, simply pull the button out.
                                                                      Figure 2-9. Powered Ext. Platform Control Box
5. LIFT ENABLE PUSH-BUTTON (Later models) -
When depressed and held, this push-button switch               1. ENABLE SWITCH(Later models)
energizes the lift circuit. It MUST be depressed and held      2. PLATFORM EXTEND/RETRACT SELECTOR
while raising or lowering the platform from this control          SWITCH
station. Release button to stop
                                                               POWERED PLATFORM CONTROL BOX - This metal
Optional Platform Controls                                     control station is mounted at the front of the powered
Operator Horn                                                  extension platform. It contains the following controls:

                                                               1. ENABLE SWITCH - This switch, when activated,
     1                                                         brings power to the Platform Extend/Retract Selector
                                                               Switch. It MUST be used while extending or retracting the
                                                               extension platform. (Later models)

                                                               2. PLATFORM EXTEND/RETRACT SWITCH -To extend
                                                               the platform, push and hold the Enable Switch forward,
                                                               then push and hold switch to “ OUT “ position until desired
                                                               extension is reached. Release switch to stop. To retract
                                                               the platform, push and hold the Enable Switch backward,
                                                               then push and hold switch to “ IN “ position until desired
                                                               retraction is reached. Release switch to stop.


                                                                                      NOTE
                                                               The extension platform MUST be fully retracted before
                                                               driving.



         Figure 2-8. Operator Horn Push-Button

1. OPERATOR HORN PUSH-BUTTON

1. OPERATOR HORN PUSH-BUTTON - This push-
button switch, when depressed, sounds an automotive-
type horn.




SECTION 2, Page 4                                                                             SJ00 Series 104282AA
Stabilizers                                                    SAFETY DEVICE OPERATION
                                                               Fold-Down Guardrail System


                                                                                                                 1
                                                   1


     3
                                                   2




                 Figure 2-10. Stabilizer                              Figure 2-11. Fold Down Guardrail System

1. STABILIZER LEG                                              1. GUARDRAIL LOCKING PIN W/LANYARD
2. STABILIZER LOCK PIN and COTTER PIN
3. STABILIZER JACK                                             FOLD DOWN GUARDRAIL SYSTEM - This system
                                                               when folded down, reduces the shut height of the work
STABILIZERS - Stabilizers are located at each of the four      platform for traveling through standard doorways.
corners of the base. To use the stabilizers, follow the
procedure below:                                               1. GUARDRAIL LOCKING PIN W/LANYARD - To fold the
                                                               guardrail system down, remove the locking pin at each
1.       Remove the Cotter Pin and Stabilizer Lock Pin         pivot point and lower each guardrail. To raise the guardrail
         and fully extend each stabilizer.                     system, swing up each guardrail and lock in place with the
                                                               locking pins ensuring that the detent ball of each pin is
2.       Align the Stabilizer Leg hole with the hole in the    clear of the side of the pivot brackets. (Figure 2-12.)
         stabilizer support tube and reinstall the lock pins
         and cotter pins.
                                                                                       WARNING
3.       Using the Stabilizer Jack Handle, rotate the
         handle clockwise to extend the jack screw until
         the footpad makes firm contact with the ground.       The guardrail system MUST be upright and locked in
                                                               place before resuming the normal operation. Check the
                      DANGER                                   guardrail system for loose or missing locking pins
                TIP OVER HAZARD                                before operating this equipment!

•        DO NOT use the stabilizers to level the machine.

•        DO NOT raise the tires off the ground with the                                          DETENT BALL
         stabilizers.                                                                            CLEAR OF SIDE
                                                                                                 OF PIVOT
NOTE: Repeat this procedure for each stabilizer.                                                 BRACKET

To store the stabilizers, follow the above procedure in the
opposite order.
                                                                    Figure 2-12. Correct Position of Locking Pin




SJ00 Series 104282AA                                                                                SECTION 2, Page 5
OPERATING PROCEDURES                                             7.      In the hydraulic/electric tray, check the hydraulic
SETUP PROCEDURE                                                          oil level (scissors MUST be fully lowered) in the
                                                                         tank. Level should be at or slightly above the
The following steps are normally required for equipment                  top mark on the gauge. If required, add a good
being put into service for the first time. After the equipment           grade hydraulic oil.
has been unloaded:
                                                                 8.      Swing the tray to the locked closed position.
1.       Remove all packing materials and inspect for            9.      Rotate the free-wheeling valve to a fully opened
         damage incurred during transport.                               position (counterclockwise).
                       NOTE
Report any damage to delivery carrier immediately.               10.     Disengage the parking brake (following the
                                                                         procedure found earlier in this section).
2.       Inspect work platform thoroughly and remove any
         foreign objects.                                                          IMPORTANT NOTE

3.       Remove the operator’s control box from its              Before pushing or towing the work platform, ensure that
         shipping container and attach it to the railing at      the brake pin is disengaged. When towing, DO NOT
         the right front of the platform. Connect the control    exceed 2 mph.
         cable to the scissors control cable.
                                                                 11.     Push or tow the work platform to a level, firm test
4.       Unlock and swing out the battery tray and               area where the work platform can be vertically extended to
         hydraulic/electric tray.                                its maximum working height.
5.       In the battery tray, check the battery water level      12.     Rotate the free-wheeling valve to a fully closed
         in all four batteries. If plates are not covered,               position (clockwise).
         carefully add distilled or demineralized water.
                                                                 13.     Raise the platform with the Up/Down Switch until
6.       If needed, connect the battery charger to the                   there is adequate clearance to lower the safety
         proper power source and charge the batteries                    bar.
         until the charger shuts off. (Refer to Battery
         Charging Procedure, this section for instructions).     14.     Lift the safety bar from its storage bracket and
         Check the specific gravity in each battery, it                  swing down into position. (Refer to label on top
         should be 1.260 to 1.275. Disconnect the battery                of base for proper procedure.)
         charger from the external power source and swing
         the battery tray to the locked closed position.         15.     Slowly lower the platform with the Up/Down
                                                                         Switch until the scissor assembly is firmly resting
                    WARNING                                              on the safety bar.
               EXPLOSION HAZARD
                                                                 16.     Inspect all hoses, fittings, wires, valves, etc. for
                                                                         leaks, looseness, hidden damage, and foreign
Keep flames and sparks away. DO NOT smoke near                           material.
batteries.
                       FIRST AID                                 17.     Raise the platform until there is adequate
Immediately flush eyes with cold water if electrolytic acid              clearance to swing up safety bar. Return safety
is splattered into them. Seek medical attention if                       bar to storage channel.
discomfort continues.
                                                                 18.     Again, raise the platform until the platform has
                                                                         reached the maximum working height.

                                                                 19.     Use the up/down Switch or Emergency Lowering
                                                                         Valve to fully lower the platform.

                                                                 20.     The Work Platform is now ready for use by an
                                                                         authorized, qualified operator who has read and
                                                                         completely understands ALL of SECTION 2,
                                                                         OPERATION in this manual.



SECTION 2, Page 6                                                                               SJ00 Series 104282AA
OPERATING PROCEDURES                                              Start and Operation
Prestart Checks                                                   Using the Base Controls:

1.          Carefully read and completely understand ALL of       1.      Turn Emergency Power Disconnect Switch to
            SECTION 2, OPERATION in this manual and ALL                   “ON” position.
            warnings and instruction labels on the work
            platform.                                             2.      Use the ladder at the rear of the work platform to
                                                                          access the work platform deck.
2.          Check for any obstacles around the work platform
            and in the path of travel such as holes, drop offs,   3.      Latch the entry chain(s).
            debris, ditches and soft fill.
                                                                  Using the Platform Controls:
3.          Check overhead clearances.
                                                                  4.      Pull out the Emergency Stop Button.
4.          Make sure the batteries are fully charged.
            Disconnect charger from AC power supply.                                    NOTE
                                                                  Extension platform MUST be fully retracted before
5.          Make sure that the free-wheeling and emergency        driving.
            lowering valves are fully closed.
                                                                  5.      TO RAISE THE PLATFORM: Select “LIFT”
                                                                          position with Lift/Off/Drive Select Key Switch.
           OPERATOR’S CHECKLIST                                           Depress and hold the Lift Enable Push-button (if
                                                                          so equipped), then Select “ UP “ position with
 INSPECT AND/OR TEST THE FOLLOWING DAILY OR AT
                                                                          Up/Down Selector switch.
 BEGINNING OF EACH SHIFT

     1.      OPERATING AND EMERGENCY CONTROLS.                    6.      TO LOWER THE PLATFORM: Select “LIFT”
     2.      SAFETY DEVICES.                                              position with Lift/Off/Drive Select Key Switch.
     3.      PERSONAL PROTECTIVE DEVICES.                                 Depress and hold the Lift Enable Push-button (if
     4.      TIRES AND WHEELS.                                            so equipped), then rotate the Up/Down Selector
     5.      OUTRIGGERS (IF EQUIPPED) AND OTHER                           Switch to “ DOWN “ position.
             STRUCTURES.
     6.      AIR, HYDRAULIC AND FUEL SYSTEM(S) FOR                7.      TO STEER: Select “DRIVE” position with Lift/
             LEAKS.
                                                                          Off/Drive Select Key Switch. Press rocker on top
     7.      LOOSE OR MISSING PARTS.
     8.      CABLES AND WIRING HARNESSES.
                                                                          of Controller Handle in the direction you wish to
     9.      PLACARDS,     WARNINGS,       CONTROL                        steer.
             MARKINGS AND OPERATING MANUALS.
     10.     GUARDRAIL SYSTEM.                                    8.      TO DRIVE FORWARD: Select “DRIVE” position
     11.     ENGINE OIL LEVEL (IF SO EQUIPPED).                           with Lift/Off/Drive Select Key Switch. Lift lock
     12.     BATTERY FLUID LEVEL.                                         ring and push Controller Handle forward. Release
     13.     HYDRAULIC RESERVOIR LEVEL.                                   to stop.
     14.     COOLANT LEVEL (IF SO EQUIPPED).
                                                                  9.      TO DRIVE IN REVERSE: Select “DRIVE”
                                                                          position with Lift/Off/Drive Select Key Switch.
                                                                          Lift lock ring and pull Controller Handle backwards.
                       WARNING                                            Release to stop.

                                                                  Shutdown Procedure
DO NOT OPERATE THIS EQUIPMENT
WITHOUT PROPER AUTHORIZATION AND                                  1.      Completely lower the platform.
TRAINING. DEATH OR SERIOUS INJURY
COULD RESULT FROM IMPROPER USE                                    2.      Turn Key to “OFF” position and remove key from
                                                                          Lift/Off/Drive Select Key Switch.
OF THIS EQUIPMENT!
                                                                  3.      Push Emergency Stop Button(s) in.

                                                                  4.      Turn Emergency Battery Disconnect Switch to
     SJ00 Series 104282AA                                                 “OFF” position. (If Equipped)
                                                                                                        SECTION 2, Page 7
                                    Table 2.1-1. Owner’s Annual Inspection Record


 MODEL NUMBER________________________________                           SERIAL NUMBER______________________
     RECORDING
       DATE

     RECORDING
       YEAR #
                     1             2            3              4            5            6            7             8
      OWNERS
       NAME

     INSPECTED
         BY




BATTERY SERVICE AND CHARGING                                       Battery Charging Procedures
PROCEDURES
Battery Service                                                                     WARNING
                                                                                EXPLOSION HAZARD
                     WARNING
                                                                   Chargers can ignite flammable materials and vapors. DO
                 EXPLOSION HAZARD
                                                                   NOT use near fuels, grain dust, solvents, or other
                                                                   flammables.
Keep flames and sparks away. DO NOT smoke near
batteries.
                                                                                      WARNING
                         CAUTION                                                   SHOCK HAZARD

Contact with electrolytic acid can cause skin irritation and       To reduce the risk of electrical shock, connect charger
damage clothing. Wear a protective apron, gloves and               only to a properly grounded single phase outlet. DO NOT
goggles when working with batteries.                               use a extension cord longer than 25 feet.

                                                                   1.      Connect charger AC plug to proper voltage source.
                      FIRST AID
                                                                           Refer to charger nameplate for voltage
                                                                           requirements.
Immediately flush eyes with cold water if electrolytic acid
is splattered into them. Seek medical attention if                 2.      Charge batteries. DO NOT leave charger
discomfort continues.                                                      unattended for more than two consecutive days.
                                                                           Severe overcharging and battery damage will result
1.        Turn Emergency Power Disconnect Switch to                        if charger fails to turn off.
          “OFF” position.
                                                                   3.      Disconnect charger from external power source.




SECTION 2, Page 8                                                                                 SJ00 Series 104282AA
BATTERY CHARGER OPERATION                                       OPERATION OF THE COMPLETELY
(If Equipped with This Type of Charger)                         AUTOMATIC BATTERY CHARGER

                                                                This charger is equipped with an electronic circuit that will
                                                                completely recharge the batteries and automatically turn
                                                                off after the charge cycle is complete.

                                                                The function of the L.E.D. indicators is as follows:

                                                                When the AC power is connected to the charger, the
                                                                L.E.D.’s will flash several times then flash independently
                                                                to check the light circuits. After the flashing sequence is
                                                                complete the “INCOMPLETE” light will come on. Five
                                                                seconds later, the “CHARGER ON” light will come on and
                                                                at the same time, the ammeter will indicate how much
                                                                current is going to the batteries.

                                                                As the charge cycle continues, which can last between 1-
                                                                1/2 hours and 16 hours for a complete cycle, depending on
                                                                the state of charge of the batteries, the “80% CHARGE”
                                                                light will come on and the “INCOMPLETE” light will go off.
          Figure 2-13. Automatic Battery Charger                When voltage of the batteries reaches approximately 30
                                                                volts, the “80% CHARGE” light will go off and the
                                                                “CHARGE COMPLETE” light will come on. This light will
BATTERY STATUS
                                                                remain on even after the charger is turned off by the
1. GREEN L.E.D .............. CHARGE COMPLETE                   electronic control. After the charger turns off, the
2. YELLOW L.E.D. ....................... 80% CHARGE             “CHARGE COMPLETE” light will indicate to the operator
3. RED L.E.D. ............................... INCOMPLETE        that the batteries are healthy and are fully charged.
CHARGER STATUS
                                                                If the “80% CHARGE” light continues to stay on after the
4. YELLOW L.E.D. ....................... CHARGER ON             charge cycle is complete, this indicates to the operator
5. RED L.E.D. ..................... ABNORMAL CYCLE              that the batteries are not capable of attaining a full charge.
                             NOTE
                                                                If the “INCOMPLETE” light remains on after the charge
On earlier chargers, the charger front panel read as            cycle is complete, this indicates to the operator that the
follows:                                                        batteries are not capable of attaining even an 80% charge.

                                                                If either the “80% CHARGE” or “INCOMPLETE” light
BATTERY CONDITION
                                                                remain on after the charge cycle is complete, the batteries
1. GREEN L.E.D ......................................... FULL   should be inspected for problems.
2. YELLOW L.E.D. ....................................... 80%
3. RED L.E.D. ............................... DISCHARGED        Your standard good watering procedures should be used
                                                                at all times.
CHARGER STATUS
4. YELLOW L.E.D. ...................... CHARGER ON
5. RED L.E.D. ..................... ABNORMAL CYCLE




SJ00 Series 104282AA                                                                                  SECTION 2, Page 9
                                  Table 2.2-1. Maintenance and Inspection Schedule


                                           Daily          Weekly           Monthly       3 Months      6 Months     12 Months*
  Mechanical
  Structural damage/welds                    A                                                                           A
  Parking brake                              B                                                                           B
  Tires/wheels & fasteners               A, B & C                                                                     A, B & C
  Guides/ rollers & slider pads          A, B & I                                                                     A, B & I
  Railings & railing lock pins            A&C                                                                          A&C
  Entry chains or gates                   B&C                                                                          B&C
  Bolts and fasteners                        C                                                                           C
  Safety Bar                                 B                                                                           B
  Rust                                                                        A                                          A
  Wheel Bearings & King pins             A, B & E                                                                     A, B & E
  Steering cylinder & tie rod                                                            A, B & E                     A, B & E
  Electrical
  Battery fluid level                        A                                                                           A
  Control switches                         A&B                                                                         A&B
  Cords & wiring                             A                                                                           A
  Battery terminals                       A&C                                                                          A&C
  Terminals & plugs                          C                                                                           C
  Generator/receptacle                    A&B                                                                          A&B
  Limit switches                             B                                                                           B
  Hydraulic
  Hydraulic oil level                        H                                                                           H
  Hydraulic Hoses/Fittings                 A&L                 C                                                      A, C & L
  Cylinders                                               A&B                                                          A&B
  Emergency lowering                         B                                                                           B
  Lift capacity                                                               D                                          D
  Hydraulic oil & oil filter                                                                               F             F
  Miscellaneous
  Manual                                   A&K                                                                         A&K
  Labels                                   A&J                                                                         A&J
  Notes
  A. Visually Inspect.                                    I.       Ensure there is no metal to metal contact with slider, slider
  B. Check operation.                                              side or running surface. Check for free movement of surface.
  C. Check tightness.                                              Also check for free movement of the slider pin through the
  D. Check relief valve setting. Refer to serial number            slider.
     nameplate.                                           J.       Replace if missing or illegible.
  E. Lubricate.                                           K.       Proper manual must be in box.
  F. Replace.                                             L.       Check For Leaks.
  G. Refer to table 2.3-1 specifications and features.
  H. Check oil level.                                     *        Record inspection date and signature.




SECTION 2, Page 10                                                                                      SJ00 Series 104282AA
                                                   Table 2.3-1, General Specifications
                                                 Specifications and Features SJ00 Series Work Platform

                     Platform        Drive         Overall     Overall      Retracted    Platform        Power Source       Wheel Type        Weight
     Model No.        Height        Height         Width       Length        Height        Size
                                                                                                         Std.       Opt.    Std.     Opt.     (Lbs.)
                     (Ft.-Ins)     (Ft.-Ins.)       (Ins.)      (Ins.)        (Ins.)      (Ins.)
      SJ005-07          16           13-6             30          82            39       28 x 82         B-24V        A      1         -       2400
      SJ005-10          16            16             42            82          39        40 x 82         B-24V        A      1         4       2550
     SJ005.5-07         18            16             32            82          39        28 x 82         B-24V        A      1         -       2400
     SJ005.5-10         18            18             42            82          39        40 x 82         B-24V        A      1         4       2550
     SJ005.8-07         19            16             32            82          40        28 x 82         B-24V        A      1         -       2400
     SJ005.8-10         19            19             42            82          40        40 x 82         B-24V        A      1         4       2500
      SJ006-07          21            16             32            82          45        28 x 82         B-24V        A      1         -       2800
      SJ006-10          21            21             42            82          45        40 x 82         B-24V        A      1         4       2950
      SJ006-13          21            21             54            86          45        52 x 82         B-24V        A      1         4       3100
      SJ006-15          21            21             60            86          47        52 x 82         B-24V        A      2         5       3150
    SJ006.5-07**        24            16             32            82          45        28 x 82         B-24V        A      1         -       2800
     SJ006.5-10         24            21             42            82          45        40 x 82         B-24V        A      1         4       2950
     SJ006.5-13         24            24             54            86          47        52 x 82         B-24V        A      2         5       3200
     SJ006.5-15         24            24             60            86          47        52 x 82         B-24V        A      2         5       3250
     SJ006.8-10         25            21             44            82          45        40 x 82         B-24V        A      1         4       2950
     SJ006.8-13         25            25             54            86          47        52 x 82         B-24V        A      2         5       3100
     SJ006.8-15         25            25             60            86          47        52 x 82         B-24V        A      2         5       3250
      SJ007-15          26            26             61            102         55        52 x 82         B-36V        A      3         -       3750
    SJ009-15-10         31            26             64            86          52        40 x 82         B-36V        A      2         5       3350
    SJ009-15-13         31            26             64            86          52        52 x 82         B-36V        A      2         5       3450
    SJ009-17-10         32            26             68            102         60        40 x 82         B-36V        A      3         -       3900
    SJ009-17-13         32            26             68            102         60        52 x 82         B-36V        A      3         -       4000

                                 Platform Capacity                               Platform Capacity (Lbs.)
                                                                                                                                 Relief Pressure
                                       (Lbs.)                                  Machines sold to Ontario Only
     Model No.
                     Main Deck       * Main Deck          Extension       Main Deck       * Main Deck           Extension   System           Lift
                    No Extension    c/w Extension          Plat. *       No Extension    c/w Extension           Plat. *     (PSI)          (PSI)
      SJ005-07           750               450               300             750               450                300        2000           1400
      SJ005-10          1000               700               300             900               600                300        2000           1600
     SJ005.5-07          750               450               300             750               450                300        2000           1400
     SJ005.5-10          800               500               300             800               500                300        2000           1400
     SJ005.8-07          750               450               300             750               450                300        2000           1400
     SJ005.8-10          800               500               300             800               500                300        2000           1400
      SJ006-07           750               450               300             750               450                300        2000           1200
      SJ006-10           750               450               300             750               450                300        2000           1200
      SJ006-13          1000               700               300             900               600                300        2000           1400
      SJ006-15          1000               700               300             900               600                300        2000           1400
    SJ006.5-07**         750               450               300             750               450                300        2000           1200
     SJ006.5-10          750               450               300             750               450                300        2000           1200
     SJ006.5-13          800               500               300             800               500                300        2000           1200
     SJ006.5-15         1000               700               300             900               600                300        2000           1400
     SJ006.8-10          750               450               300             750               450                300        2000           1200
     SJ006.8-13          800               500               300             800               500                300        2000           1200
     SJ006.8-15         1000               700               300             900               600                300        2000           1400
      SJ007-15          1000               700               300             900               600                300        2000           1400
    SJ009-15-10         1000               700               300             800               500                300        2000           1400
    SJ009-15-13          800               500               300             800               500                300        2000           1200
    SJ009-17-10         1000               700               300             900               600                300        2000           1400
    SJ009-17-13         1000               700               300             900               600                300        2000           1400
   * Extension Deck Capacity May be Increased to 300 lbs from 250 lbs Provided the Main Platform Capacity is Lowered by 50 lbs.
   OPTIONS:        -Outriggers Optional for All Models. (** Standard on SJ006.5-07 Model)
                   -Auxiliary Extension Platform, 6ft Crank-Out Platform or 3ft Roll-Out Platform.
                   -Wheel Type, (1) 16 x 4 Hard Rubber, (2) 18 x 5.5 Hard Rubber, (3) 26 x 12 Urethane Filled, (4) 16 x 6.5 Urethane
                   Filled, (5) 18 x 9.5 Urethane Filled
SJ00 Series 104282AA                                                                                                             SECTION 2, Page 11

				
DOCUMENT INFO
Shared By:
Categories:
Tags:
Stats:
views:10
posted:3/9/2011
language:English
pages:11