Docstoc

Tracer KB

Document Sample
Tracer KB Powered By Docstoc
					x00031 1/15   Kbtrac3.wpd   04/08/98
                                                 TABLE OF CONTENTS
                                                                            TRACER - KB
T R A C E R - KB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -2-
G E N E R A L D E S C R I P T I O N . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -3-
        The KEYBOARD / DISPLAY units can display the following information: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -3-
        Through the KEYBOARD / DISPLAY it is possible to perform the following operations: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -4-
        REPORTING OF AN ALARM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -4-
I N S T A L L A T I O N . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -5-
        1 - ALARM CIRCUIT CONNECTIONS: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -5-
        2 - SIREN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -5-
        3 - BUZZER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -5-
        4 - EXTERNAL LIGHTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -5-
        5 - POWER SUPPLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -5-
        6 - KEYBOARD / DISPLAY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -5-
        7 - BATTERY CONNECTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -5-
W I R E L E S S S E N S O R S . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -6-
        SYSTEM CODE CHANNEL SETTING (TRACER-DSP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -6-
        REMOTE CONTROL CHANNEL SETTING (TRACER-DSP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -6-
O P E R A T I O N . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -7-
        REMOTE PANIC BUTTON . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -7-
        SECURITY LIGHTS OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -7-
        CUSTOMER programming mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -7-
THE DISPLAY on the REMOTE UNIT: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -8-
        ARMED ZONES 1 TO 8 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -8-
        WARN ZONES 1 TO 8 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -8-
        AUXILIARY INDICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -8-
THE KEYBOARD / DISPLAY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -9-
        MULTIUSER OPERATION (ZONE-SHARING): . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -9-
CUSTOMER INSTRUCTIONS FOR ARMING, DISARMING AND SETTING THE WARNING MODE FACILITY. . . . . . . . . . . . . . . . . . . . . . -10-
        REMOTE CONTROL OPERATION: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -10-
        ARMING YOUR SYSTEM ON LEAVING THE PREMISES. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -10-
        DIS-ARMING UPON ENTERING THE PREMISES. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -10-
        ARMING THE SYSTEM WHILE AT HOME: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -10-
        DIS-ARMING THE "TRACER" . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -10-
        ENTERING THE WARNING MODE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -10-
KEYBOARD OPERATION: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -11-
        ARMING YOUR SYSTEM ON LEAVING THE PREMISES: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -11-
        DIS-ARMING UPON ENTERING THE PREMISES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -11-
        ARMING THE SYSTEM WHILE AT HOME: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -11-
        DIS-ARMING OR RESETTING THE SYSTEM. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -11-
        SELECTING THE WARNING MODE: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -11-
MANUFACTURER'S NOTE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -11-
appendix “A”          Key-board entries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -12-
                T R A C E R - KB
                    Telephone & Radio Alarm Control & Emergency Reporter
                                                    04/08/98


The "TRACER-KB" is a microprocessor based INTRUSION DETECTION UNIT with optional RADIO or TELEPHONE
COMMUNICATOR designed to perform all the functions associated with the monitoring of alarm conditions and
subsequent transmission to a REMOTE LISTENING CENTRE or to a PRIVATE TELEPHONE.

These are the features that make the "TRACER-KB" a versatile , efficient and innovative ALARM CONTROL UNIT:

- 8 zones BOTH WIRED and WIRELESS.
- BOTH KEYBOARD and REMOTE CONTROL operation.
- All zones programmable to suit ANY special installation requirement.
- Programmable "entry and exit delay" for hands-free operation on any of the 8 zones.
- Programmable siren activation for each circuit.
- Remote PANIC button.
- AUTOMATIC ACTIVATION of security lights on alarm or warning conditions.
- VHF, UHF or TELEPHONE communicator to report to a control room.
- Built in 3 amps power supply and battery charger.
- Stand-by 6.5 A/h battery (72 hrs autonomy).
- Buzzer output for indicating signals (arm, disarm, battery-low etc....).
- When triggered, sends the conditions of all 8 circuits.
- Programmable silent PANIC alarm.
- Programmable arm/disarm indicating signals on the siren.
- Programmable auto transmission of battery low condition in sensors and their I.D. code.
- Programmable auto transmission of system mains failure as well as mains restoral.
- Programmable auto transmission of system battery low condition and restoral.
- Programmable auto transmission of arm and disarm operations.
- Subscriber code and options fully programmable by the installer.
- All options programmable from any keyboard.
- EEPROM memory for retention of both options and code selections during "power-down".
- It can generate a TEST transmission to the control room by use of the remote control.
- Programmable to send a "check-in" transmission every 1 to 250 hours.
- All operations are performed through a 2 CHANNEL HAND-HELD REMOTE CONTROL.
- Up to 4 keyboards on a 4 wired system.
- Installer code for programming the options registers.
- 4 users with optional "Zone-sharing " facilities
- Each keyboard with 4 individual user codes and installer codes.
- Four preset levels of activation “A, B, C, or D”.
- Extensive diagnostic for testing wireless devices.
- Special option for "Follow-me" telephone operation.
- Visualisation of current options and settings for easy programming.
- Reporting of alarm conditions to a control room via radio, telephone or both.
- Seven output extended signals for triggering NON-MAMI radio or telephone communicators.
- Transmission of an alarm is programmable for each circuit.
- Disabling facility for each of the individual keyboards.
- Operation of gate automation via the keyboards relays. (OPTIONAL).
- Triggering of a synthesised message when disarming the system. (OPTIONAL)
- Activation of listening-in devices (or intercoms) connected at any of the 4 keyboards .(OPTIONAL)
- Automatic scanning of listening-in devices.(OPTIONAL)




                                                       -2-
                  GENERAL                                 DESCRIPTION
The "TRACER-KB" is capable of monitoring BOTH WIRED and WIRE-LESS detector circuits at the same time.
A REMOTE PANIC BUTTON system is built in as a standard feature.

The "TRACER-KB" will alarm/report whenever the following inputs are triggered:


- Any of the 8 wired active inputs.
- Any of the 8 wireless active inputs.
- Remote panic button.

- Supervisory signals such as:
     - battery low in the wireless sensors.              - low battery in the system.
     - arm / disarm. - battery restoral in system.
     - mains failure. - test transmission
     - mains restoral
For complete flexibility the eight wired inputs may be programmed to send an alarm whenever one of the following
conditions occur:
  - When the external circuit is opened (Normally Closed circuit).
  - When the external circuit is closed (Normally Open circuit).
  - Both when the external circuit is Opened or Closed.
       (In this case it is possible to program any of the circuits as an "alarm circuit" or a "door entry monitoring circuit").
  - When the trigger condition has occurred for longer than 15 sec (slow detection).

For example : You may require that the particular circuit calls the control room both when an alarm occurs and when
it is restored, or that a particular circuit calls the control room both when a door is locked or unlocked.

The eight wireless inputs work in "parallel" to the wired inputs and therefore share all the available optional
features such as:
 - individual siren activation selection.       - individual "entry delay" selection
 - individual "warning only" selection.         - individual "24 hrs" ready activation.

A great feature of the "TRACER-KB" is the fact that it is fully programmable to suit every requirement. It will allow
you, for instance, to define 4 patterns each containing a set of "armed" zones which you will mostly select in everyday
operation. You do not have to remember which set you normally arm or put onto warning mode. The "TRACER-KB"
will memorize the four patterns for you and so, when arming the system, automatically step through these preset
patterns allowing you to stop at the one you desire. These patterns may be changed at will using the two buttons
on the hand-held remote control.

ALL COMMANDS and INDICATIONS are performed and shown on extended, wall mounted keyboards /
displays units . Up to 4 units may be connected in parallel using only 4 wires.

The KEYBOARD / DISPLAY units can display the following information:
      - the wireless sensor or circuit which has caused the alarm to trigger.
      - the wireless sensor or circuit which has caused the warning signal.
      - which of the 8 circuits are 24hrs, armed or on warning.
      - system battery is only 20 % charged.
      - mains failure has occurred.
      - delay-in circuit has been initialized.
      - system has triggered and the signal was sent to control room.
      - system armed / disarmed indication.

They also retain the type of transmission which was sent to the control room e.g.:
       - Numbers 1 to 8 indicating the alarm circuit which was triggered.
       - The letter "p" indicating panic button activation.
       - The letter "t" indicating test transmission.
       - The letter "b" indicating battery low in one of the wireless sensors.
       - The letter "r" indicating that the system had a reset.
       - The letter “h” indicating a warning or a call facility.




                                                              -3-
Through the KEYBOARD / DISPLAY it is possible to perform the following operations:
- program the system's options.
- access the 4 preset patterns and if necessary change them.
- access each zone individually.
- change the user codes ( 4 different user codes per keyboard ).
- activate a panic alarm .
- activate a test signal.
- reset the system /alarm .
- program the tel. number for the "follow-me" reporting .

Combination of 2 keys pressed simultaneously will give different conditions, these are shown in appendix “A”:

NOTE:
When arming the system if any of the zone is in “alarm” condition the system will sound the keyboard buzzer for 10
seconds before initializing the arming sequence.
During the arming sequence it is possible to cancel the operation by pressing 0..0..0 .
By pressing 1..1.. 1 the system will arm immediately to the preselected level.

MOST COMMANDS can also be performed through a 2 CHANNEL HAND-HELD REMOTE CONTROL:
- arming and disarming of the system     - partial arming.
- partial "warning only" selection.      - programming of the different patterns of activation.
- panic button.                          - test transmission.
- security lights

REPORTING OF AN ALARM
Reporting of an alarm can be achieved in 4 different modes:

BY RADIO: The system will transmit , via radio, 3 times at random within 25 seconds

BY TELEPHONE: The System will communicate with the base station via telephone using 2 alternative numbers. If the
“FOLLOW-ME “ option is set the second number can be that of a “cellular” , a friend or a neighbour and therefore can
be changed at will by user “1" .NOTE the signal to the alternative no is not intelligible but merely a digital sound.

BY RADIO AND TELEPHONE: after transmitting 3 times via radio the system will use the telephone to communicate
the signal to a base station or private telephone number.

NO REPORTING
when neither communication is selected the system latches, for 3 seconds, 7 different conditions on to an expander
card (optional) to drive non MAMI communicators or radio transmitters.
These signals are:
- panic
- system dis-armed
- system armed
- system battery failure
- sensor battery low
- test
- intrusion


After each Radio reporting the “running” LED on the key board will flash for 12 seconds to allow all passive detectors
to settle down. During this period the system is dormant.




                                                         -4-
                                  INSTALLATION
Installing the "TRACER-KB" is a very simple, as the power supply for instance is already built into the unit. All you have
to do is connect the external receiver and/or the long range transmitter or telephone communicator. The connections
are easy to read and to understand. Then all you have to do is connect the battery, the external transformer and wire
up the different zone circuits and audible devices such as the buzzer and siren. These connections are as follows :
(CONNECTOR STRIPS A and B )
               BUZZER
                    LIGHTS
       SIREN

                                                          AC             BAT SPLY TO P.I.R.
                                                         17V              - +        + + +




                CONNECTOR      "A" ( TOP)                 CONNECTOR      "B" ( BOTTOM)
1 - ALARM CIRCUIT CONNECTIONS:
There are 8 inputs available on the TRACER-KB ( A8 TO A15 ). These INPUTS are factory-programmed for
NORMALLY-CLOSED operation, that is: You need to REMOVE 12 V (from the common 12V CONNECTIONS B13,
B14 and B15) to trigger the alarm.( See connection diagram 2 )

 If you require any of these to be NORMALLY-OPEN ( trigger on applying 12V), it is necessary to define these
circuits in the INVERT register (see "PROGRAMMING THE TRACER "(key .3))
 Entering "0" will change that circuit from N.C. to N.O. All these inputs have Metal Oxide Varistors and current
limiting devices for lightning protection.
     Power to the detectors is taken from B13, B14, B15 (POS.) and B10, B11, B12 (NEG)

2 - SIREN
12 Volts DC is available between connectors A1(-) & A2(+) to operate the external siren. The siren will automatically
RESET 3 minutes after activation. (1 - 255 Seconds)

3 - BUZZER
12 Volts DC is available between A3(-) & A4(+) to operate an optional buzzer.

4 - EXTERNAL LIGHTS
12 Volts DC is available between A5(-) & A6(+) to operate a heavy duty 220v a.c. relay or contactor to control particular
light circuits. Option 4 of register 1 will allow for the lights to switch on with an alarm or a warning and switch off 4
minutes later. The security lights can also be activated manually using a REMOTE -CONTROL with bridges on
channels 2&3 . The lights will switch off 4 minutes after the last activation.
NOTE : The combined current the 3 relays may supply is limited by a 1.5Amp fuse.

 5 - POWER SUPPLY
15-17 Volts AC may be supplied to the "TRACER" on contacts B1 and B2. This input has a Metal Oxide Varistor for
lightning protection. The transformer should have a rating of at least 800 mA (3 amps when using a radio
communicator.)

6 - KEYBOARD / DISPLAY
The 4 wires to the remote display units are connected as follows:
[B5] (T) for transmitted data line 1               [B3] (R) for received data line 2
[B6] (-) for negative supply ( 0v)                 [B7] (+) for positive supply (12v)
7 - BATTERY CONNECTIONS
The stand-by battery ratings must be : 12v with a recommended capacity of 6.5 A/hr
The standby battery must be connected between B8(NEGATIVE) and B9(POSITIVE).
To optimize the maximum power which the battery can supply when using a radio transmitter crowbar polarity
protection method has been implemented. It is therefore necessary to change the GENERAL and OUTPUT
fuses after connecting the battery incorrectly.
Our guarantee DOES NOT cover damages caused by REVERSE/INCORRECT polarity connection to the
battery.

Special components have been introduced to protect the keyboard and detectors power supply from short circuits.
The characteristic of these devices is such that on excessive current they will heat up and reduce the current . Only
once the short has been removed will they slowly recover to their initial value.
It is important to remember that the maximum current available on either the keyboard or the P.I.R.
circuits is 700 mA before limiting takes place.

                                                           -5-
                               WIRELESS                               SENSORS
              Using wireless sensors is simple! - provided that you are aware of the following facts:

1 - Transmission of alarms occurs for only a short period of time (3 - 5 Seconds)

 2 - The sensors are designed to save battery power as much as possible and therefore will not transmit if
continuous movement is detected. From the last movement detected they will return to an active state within either
30 sec (test mode ) or 3 minutes (normal mode).

 3 - The radio transmission range may vary widely from one installation and location to another. The                        position of
the radio receiver is therefore critical and must be chosen accordingly.

4 - The tuning of the radio transmitter in the sensor and in the receiver itself is critical . Any changes or retuning will
affect its performance.

There are two operations which must be carried out to interface wireless sensors to the "TRACER" so that they may
communicate properly and not interfere with one another.

SYSTEM CODE : The first is the setting of the 10 way dip switch inside the sensors.
   This will give the system its own and unique identification by which all the sensors will be recognised.
   [ NOTE: To enable the battery-low detection circuit in the sensors it is necessary to have
   dip-switch 7 set to "OFF" (this will not affect the systems coding)].

I.D. SETTING : The second is to make each sensor and other wireless devices identifiable within
the system. This is done by encoding "jumpers" 1, 2 , 3 and 4 - see table below.


                  SYSTEM CODE CHANNEL SETTING (TRACER-DSP)
 BRIDGE NO.                 FUNCTION                       APPLICATION                 BRIDGE NO.              FUNCTION
 1=ON 0=OFF               WHEN ACTIVATED                                               1=ON 0=OFF
 4   3   2    1                                                                        4   3       2       1
 0   0   0    0    WARNING (1 SEC ON BLEEPER)   DOOR BELL/POOL WARNING                 1   0       0       0   ZONE 1
 0   0   0    1    PANIC ACTIVATION                                                    1   0       0       1   ZONE 2
 0   0   1    0    not used                     EMERGENCY / MEDICAL ASSISTANCE         1   0       1       0   ZONE 3
 0   0   1    1    not used                                                            1   0       1       1   ZONE 4
 0   1   0    0    not used                                                            1   1       0       0   ZONE 5
 0   1   0    1    not used                                                            1   1       0       1   ZONE 6
 0   1   1    0    EXTERNAL LIGHT ACTIVATION    SECURITY LIGHT / SENSOR ACTIVATION     1   1       1       0   ZONE 7
 0 1     1 1 not used                                                                  1   1       1       1   ZONE 8


REMOTE CONTROL CODE : First set the the 10 way dip switch inside the remote . This gives the remote
control its own and unique identification from which the tracer will recognise the commands.
-This code should be different from the system code (above)

REMOTE CONTROL CHANNEL SETTING: This will make the remote control perform different function as
described in the table below
This is done by encoding "solder bridges inside the remote control itself (these are normally set in the factory).



             REMOTE CONTROL CHANNEL SETTING (TRACER-DSP)
 BRIDGE NO.                     FUNCTION                      APPLICATION                  BRIDGE NO.           SENSOR
 1=ON 0=OFF                   WHEN ACTIVATED                                               1=ON 0=OFF
 4   3   2    1                                                                            4   3       2   1
 0   0   0    0    WARNING (1 SEC ON BLEEPER)     DOOR BELL/POOL WARNING                   1   0       0   0    (MEDICAL)
 0   0   0    1    PANIC ACTIVATION               EMERGENCY / MEDICAL ASSISTANCE           1   0       0   1    not used
 0   0   1    0    ARM / DISARM                   TURN SYSTEM ON OR OFF                    1   0       1   0    not used
 0   0   1    1    TEST TRANSMISSION              CHECK IF THE SYSTEM IS WORKING           1   0       1   1    not used
 0   1   0    0    ARM ONLY (to d level)                                                   1   1       0   0    not used
 0   1   0    1    DISARM ONLY                                                             1   1       0   1    not used
 0   1   1    0    EXTERNAL LIGHT ACTIVATION      SECURITY LIGHT / MANUAL ACTIVATION       1   1       1   0    not used
 0   1   1    1    not used                                                                1   1       1   1    not used




                                                                -6-
                                 O P E R A T I O N
After the installation is completed, this is what you should see on the remote KEYBOARD/DISPLAY:

"MAINS" indication                     (L.E.D)             OFF
"LOW BATTERY" (in sensors)             (L.E.D)             OFF
"SYSTEM ARMED" indication              (L.E.D)             OFF
"TRIGGERED" indication                 (L.E.D)             OFF
"DELAY" indication                     (L.E.D)             OFF
"RUNNING" indication                   (L.E.D)             FLASHING
"ARMED" indication                     RED (L.E.D’S)       ON [only the PERMANENTLY-ARMED (24hrs) zones.]
"WARNING" indication                   YELL (L.E.D’S)      ALL OFF
Note: Some of the warning lights may temporarily be ON     to indicate that some of the zones (doors, windows or
    motion detectors) are still activated.

REMOTE PANIC BUTTON
The remote controls may be supplied with either 1 (RED) or 2 (RED & GREEN) buttons:

  - The RED button will ALWAYS trigger the emergency operation.
  - The GREEN button is used to arm, disarm, and reset the system.
  - The GREEN & RED buttons pressed together will send a test transmission to the control room (only when
     using a radio or telephone communicator) .

 - Once you have pressed the GREEN button to arm the system, you have four selections:

1 - Let the system automatically step through the three patterns "A", "B" , "C" and automatically arm
    itself with pattern "D".

2 - While stepping through levels "A", "B", "C" and "D", press the RED button at the one
    required and arm the system with THAT pattern OR......

3 - While stepping through, press the GREEN button at the pattern required and select those zones which
     will give you a warning when triggered OR.....

4 - While stepping through the preset patterns press both buttons at the same time to access the CUSTOMER
    programming mode (see below) which allows you to change the zone configuration in that pattern.

To disarm the system, following any of the first 3 choices (1, 2, or 3), press the GREEN button until a 2 beep
signal (dis-armed) is heard though the buzzer/siren or the remote display.

SECURITY LIGHTS OPERATION
By pressing buttons B and C on a 3 channel remote control, will activate the security lights relay. This will remain
on for 4 minutes or until the remote control is pressed again.
If the lights are turned on by a sensor ( system dip-switch setting) they will remain on for 4 minutes from the last
activation.

CUSTOMER programming mode
Note: It is strongly recommended that this be done in consultation with your installer.
If you have entered the programming mode (4) a yellow light will be ON for zone No. 1.

The two remote buttons have now assumed different roles where the GREEN button will toggle the
corresponding red light and the RED will step to the next zone.
This way it is possible to change the patterns to suit new requirements.
An error may be easily rectified by pressing the RED button again either to toggle back or, pressing the green
button, to step right around.
If, for security reasons, you wish to change the code in the REMOTE CONTROL , simply change the dip-switch
setting to the required code before leaving the programming mode.
To leave the programming mode PRESS BOTH BUTTONS TOGETHER (Green & red).




                                                         -7-
THE DISPLAY on the REMOTE UNIT:
ARMED ZONES 1 TO 8
The RED lights indicate which of the zones are armed.
       - A steady light indicates that the zone is permanently armed (24 hrs).
       - A running light indicate which zones are being monitored for an alarm condition.

WARN ZONES 1 TO 8
The YELLOW lights indicate which of the zones are in warning mode.
        - The running lights indicates which zones are being monitored for a warning condition.
        - A steady light indicates that the zone is being activated .
This gives you the facility , when leaving your home to check whether you left any of the windows or
doors open . ( The buzzer will also remain on during arming sequence.)

AUXILIARY INDICATIONS

 MAINS        MAINS FAILURE indication:
              This indicator will be on to indicate that either there is an A.C power failure or that the transformer
              supplying power to the system has been accidentally unplugged.

 BCKUP        SYSTEM BATTERY LOW indication:
              The system's battery is left with only 20% of its nominal charge. (Check mains)

 L.BAT        WIRELESS-DETECTOR BATTERY-LOW indication:
              This light will be activated by "poor condition" of the battery in the wireless sensor shown by the
              digit display . (Change the battery in the sensor indicated).

 ARMED        SYSTEM ARMED indication:
              This light is on whenever the system is either armed or set on warning mode.

 TRIGG        SYSTEM TRIGGERED indication:
              This intermittent light warns you that an alarm activation has occurred while you were away.

 DELAY        ENTRY DELAY indication:
              It is often required that some of the zones activate only after a preset time delay. This is done when
              you , the user , would like to keep the arm/disarm REMOTE CONTROL in the house rather then
              carrying it around at all times. This light will warn that you have initiated a time delay on one of the
              zones and that you have a limited time (programmable) to reach the REMOTE CONTROL or the
              KEYBOARD and disarm the system.

 RUNNG        SYSTEM RUNNING indication:
              This light reassures you that the system is running correctly. If this indicator does not flash regularly,
              please contact your installer.


Note: MAINS, BCKUP, L.BAT, TRIGG and DELAY indications may be individually made to buzz
         Together with the indicator on the keyboard/display. (Local keyboard option register no. 3)




                                                          -8-
THE KEYBOARD / DISPLAY
Each keyboard is capable of storing in memory one INSTALLER code and four USER codes ( 4 digits).
Each code performs different tasks.

INSTALLER CODE : (factory default 1 0 0 0 )
The installer code is used to setup the system, program the options required, test some of the features and
perform the following operations:
             - Programming of the system options. (see table 1)
             - Programming of the options for the detection circuits . (see table 3)
             - Programming subscriber (Customer) code. (see table 2)
             - Programming of the system I.D. dip switches. (see table 2)
             - Programming of the 4 preset patterns. (see table 3)
             - Programming the telephone numbers of the monitoring centre (control room). (see table 5)
             - Programming the telephone number for " follow-me " operation. (see table 5)
             - Resetting the system to factory defaults . (see table 1)
             - Enter the wireless test mode .

USER 1 CODE : (factory default 1 1 1 1 )
The user 1 code allows the following operations:
            - Select any of the 4 preset patterns. (see table 5)
            - Select any of the individual zones . (see table 5)
            - Reset the system/alarm. (see table 5)
            - Display the first 3 alarm activations.(TABLE E) (see table 5)
            - Change his/her own password and those of users 2, 3, and 4. (see table 5)
            - Programming the telephone number for " follow-me " operation. (see table 5)

USER 2,3 and 4 CODES :(factory defaults 2 2 2 2 , 3 3 3 3 and 4 4 4 4 )
User codes 2, 3, and 4 allow the following operations:
           - Select 1 of the 4 preset patterns.(see table 6)
           - Reset the system/alarm.(see table 6)
           - Change his/her own password (see table 6)

USER 5 CODE: (Factory defaults to 5555)
  Normal mode: User 5 is the servant function in normal mode and can only arm/disarm the ‘A’ preset level
  Multiuser mode: Because the superpower of user 1 is not required in multiuser mode, user 5 takes its place.
        - Select preset level ‘A’ only
        - Share the same function as other users (See multiuser mode)

It is possible to allocate each keyboard its own I.D. number (1 to 4). This allows the TRACER-KB to address each
keyboard individually.(see table 4)

Whenever mains failure or battery low conditions occur the buzzer will sound, this can be silenced by holding
the "0" key. The buzzer is enabled for these two events in the buzzer enable option register. (see table 4)

MULTIUSER OPERATION (ZONE-SHARING):
(Only applicable on software versions S0001Axx, where ‘xx’ is version 02 or later)

One of the greatest features of the TRACER-KB is the possibility to operate in the MULTIUSER or ZONE-
SHARING facility This option is set in the option register 1.
The multiuser mode allows 4 users to operate individually the same control panel and accessories but share
some of the zones.
 In this mode USER 1 is replaced by a user 5 who has the same rights as users 2,3 and 4.

Understanding how the zone-sharing concept works is simple .... just remember the following:

Assume that users 2 and 3 are sharing some zones....
To DISARM shared zones think of the OR function (e.g. EITHER user 2 OR user 3 can disarm )
To ARM shared zones think of the AND function ( e.g. BOTH user 2 AND user 3 must arm)

It is possible to use a remote control with every user by changing the solder bridges on the TOPO remote controls.
Please refer to the table below.
Every time one of the users arms/disarms the system , the new condition is reported to the control room.
Note: Special caution must be made to ensure that the passwords for other users not required must not be
left at factory default by the installer and that the different levels A,B,C & D need to correspond to the
relative partition.


                                                        -9-
YOUR "   TRACER-KB"                             SECURITY SYSTEM
    CUSTOMER INSTRUCTIONS FOR ARMING, DISARMING AND SETTING THE
                     WARNING MODE FACILITY.
There are EIGHT working zones on your TRACER-KB alarm system.
These EIGHT zones correspond to the following areas in the house.

ZONE 1. _________________________________ ZONE 5. _________________________________

ZONE 2. _________________________________ ZONE 6. _________________________________

ZONE 3. _________________________________ ZONE 7. _________________________________

ZONE 4. _________________________________ ZONE 8. ________________________________


                                       zone allocation for each level
                   ZONE          ZONE         ZONE         ZONE         ZONE        ZONE         ZONE        ZONE
 Level “a”
 Level “b”
 Level “c”
 Level “d”
REMOTE CONTROL OPERATION:
1. PRESSING THE RED BUTTON will activate the siren and transmit a panic signal to the Control Room.
2. PRESSING THE GREEN BUTTON will arm, dis-arm and reset the system.
3. PRESSING THE GREEN AND THE RED BUTTONS TOGETHER will send a test signal to the Control Room.
ARMING YOUR SYSTEM ON LEAVING THE PREMISES.
1. Secure all doors and windows.
2. When outside, press the GREEN BUTTON once. This will be acknowledged with ONE BEEP.
   After stepping through the four levels, there will be another beep .
3. Your system is now ARMED.
DIS-ARMING UPON ENTERING THE PREMISES.
1. Press the GREEN BUTTON once. This will be acknowledged with TWO-BEEPS.
2. The SYSTEM is now DIS-ARMED.
ARMING THE SYSTEM WHILE AT HOME:
Selecting the designated sections to be armed:      (Refer to the above table )
1. Press the GREEN BUTTON once. The system automatically steps through LEVELS "A" to "D"
2. Stop the keypad/display at the level required by pressing the RED BUTTON once .
3. The system is now ARMED at this selected level.

DIS-ARMING THE "TRACER"
1. Press the GREEN BUTTON once. This will be acknowledged with TWO BEEPS.
2. The system is now DIS-ARMED.
ENTERING THE WARNING MODE
Note that following mode WILL NOT trigger the siren or send a signal to the Control Room.
The buzzer will warn you whenever a zone is being violated.
Select the designated level to be in the warning mode. (Refer to the above table )
1. Press the GREEN BUTTON once. The system automatically steps through levels "A" to " D."
2. Stop the display at the level required by pressing the GREEN BUTTON once .
3. The system is now SET TO WARNING MODE at this selected level.
 GENERAL NOTES:
-Resetting of the system may occur at any time using the GREEN button.
-Indications on the remote display units are retained until the system is armed again. This will allow you to ascertain
the cause of the alarm even after resetting.


                                                          -10-
KEYBOARD OPERATION:
User 1 has access to all the features of the system including those of the remote control.
Note “1111" is factory default user code and can be changed through programming.

ARMING YOUR SYSTEM ON LEAVING THE PREMISES:
a) (Enter user code)1 1 1 1 # (Enter the level required) a, b, c, or d (Enter) A .
     (If you need to select a preset level).
b) (Enter user code) 1 1 1 1 # (Enter the zones required) 1 to 8 (Enter) A
     (If you need to select individual zones).
     (If an exit delay had been programmed, you have preset time to leave the premises).

DIS-ARMING UPON ENTERING THE PREMISES
a) (Enter user code) 1 1 1 1 # #
   (All zones will be dis-armed).
   (if an entry delay had been programmed, you have preset time to enter the premises
   and disarm the system).

ARMING THE SYSTEM WHILE AT HOME:
a) (Enter user code) 1 1 1 1 # (Enter the level required) a, b, c or d (Enter) A . (to select a preset level ).
or
b) (Enter user code) 1 1 1 1 # (Enter the zones required) 1 to 8 (Enter) A .
    (If you need to select individual zones) -(The selected RED LED's will light-up.

DIS-ARMING OR RESETTING THE SYSTEM.
(Enter user code) 1 1 1 1 # #

SELECTING THE WARNING MODE:
a) (Enter user code) 1 1 1 1 # (Enter the level required) a,b,c or d (Enter) B. (if you need to select a preset level)
    or
b) ( Enter user code) 1 1 1 1 # (Enter the zones required) 1 to 8 (Enter) B.
    (if you need to select individual zones) - The selected yellow LED's will light-up.

DISABLING THE KEYBOARDS
Each keyboard can be disabled individually. Only user 1 code will operate without any visual or audible indication.
To disable temporarily a keyboard enter the user code with a long # key. enter "D" the display and the buzzer will
become inoperative . To re-enable the keypad repeat the operation.
REMEMBER THAT THE SECOND TIME THERE IS NO INDICATION FROM THE BUZZER ON THE KEYPAD
 Notes :
 1- Both entry and exit delays will be indicated by an intermittent buzzer (if so selected).
 2- Running" LED'S on the display indicate zones being monitored.
 3- Steady" LED'S on the display indicate "permanently" armed zones.
 4- To silence "battery low" and "mains failure" buzzer hold "0" until the buzzer is switched off.
 5- Pressing these 2 keys simultaneously will cause the following signals to be activated:
    * and # will activate a panic signal.
    7 and 9 will activate the lights.
    4 and 6 will activate the transmitter for a test transmission.
    1 and 3 will activate the medical, help or call function.

PLEASE TEST YOUR SYSTEM REGULARLY ( at least once a week) WITH THE CONTROL ROOM.


MANUFACTURER'S NOTE
CONGRATULATIONS !!       YOU ARE NOW THE OWNER OF ONE OF THE MOST SOPHISTICATED ALARM
SYSTEMS IN SOUTH AFRICA. THE "TRACER" SYSTEM HAS EVOLVED OVER THE LAST 10 YEARS, DURING
WHICH TIME THE TECHNOLOGY APPLIED WAS CONTINUOUSLY IMPROVED AND PERFECTED. THIS LATEST
MODEL OF THE "TRACER" HAS BEEN DEVELOPED WITH THE CONSUMER'S INTERESTS IN MIND - IT IS USER
FRIENDLY, IT IS VERSATILE, IT ENCOMPASSES ALL LATEST FEATURES OF AN ALARM SYSTEM AND ABOVE
ALL, IT IS 100% A SOUTH AFRICAN PRODUCT. WE TRUST IT WILL SERVE YOU WELL AND AFFORD YOU
COMPLETE PEACE OF MIND, WHETHER AT HOME OR AWAY.




                                                          -11-
appendix “A”                                                     Key-board entries
INSTALLER
1000 # 0 1   = SET OPTIONS 1 OF THE SYSTEM (8 BITS)              1000 # 0 7   = SET ALM / RESTORE ON EACH INPUT (8 BITS)
1000 # 0 2   = SET OPTIONS 2 OF THE SYSTEM (8 BITS)              1000 # 0 9   = SET ERASE EEPROM
1000 # 0 3   = SET INVERT REGISTER (8 BITS)                      1000 # 0 A   = SET LEVEL A (8 BITS)
1000 # 0 4   = SET DET. DELAY FOR EACH CIRCUIT. (8 BITS)         1000 # 0 B   = SET LEVEL B (8 BITS)
1000 # 0 5   = SET SIREN ON EACH INPUT (8 BITS)                  1000 # 0 C   = SET LEVEL C (8 BITS)
1000 # 0 6   = SET OPEN / CLOSE ON EACH INPUT (8 BITS)           1000 # 0 D   = SET LEVEL D (8 BITS)

1000 # 1 0 = SET SPEECH TRIGGER KEYPAD (only with KEYBOARDS-R( with relays)
1000 # 1 1 # = PROGRAM TEL NO 1 (16 DIGITS)               1000 # 1 2 # = PROGRAM TEL NO 2 (16 DIGITS)
1000 # 1 1 * = DISPLAY TEL NO 1 (16 DIGITS)               1000 # 1 2 * = DISPLAY TEL NO 2 (16 DIGITS)
1000 # 1 4 = NO COMMUNICATOR SELECTION (8 BITS)           1000 # 1 A = SET DIP SW OF SYSTEM
1000 # 1 5 = 24 HRS CIRCUITS (8 BITS)                     1000 # 1 B = SET DIP SW OF REMOTE
1000 # 1 6 = ENTRY DELAY (8 BITS)                         1000 # 1 C # = SET SUBSCRIBER CODE (4 DIGITS)
1000 # 1 7 = ENTRY DELAY VALUE (8 BITS)                   1000 # 1 C * = DISPLAY SUBSCRIBER CODE (4 DIGITS)
1000 # 1 8 = CHECK-IN TIME (8 BITS)                       1000 # 1 D = SET RADIO TEST MODE ("0" TO EXIT)
1000 # 1 9 = SIREN DURATION (8 BITS)
1000 #–># 1 = SET OPTIONS 1 ON THE LOCAL KB (LONG KEY)    1000 #--># 3 = SET BEEPER ON THE LOCAL KB
1000 #--># 2 = SET OPTIONS 2 ON THE LOCAL KB (LONG KEY)   1000 #--># 9 = CLEAR EEPROM ON THE LOCAL KB (LONG KEY)
1 000 #--># C 1 = CHANGE PASSWORD USER 1 ON THE LOCAL KB (LONG KEY
1000 #--># C 2 = CHANGE PASSWORD USER 2 ON THE LOCAL KB (LONG KEY)
1000 #--># C 3 = CHANGE PASSWORD USER 3 ON THE LOCAL KB (LONG KEY)
1000 #--># C 4 = CHANGE PASSWORD USER 4 ON THE LOCAL KB (LONG KEY)
1000 #--># C 5 = CHANGE PASSWORD USER 5 ON THE LOCAL KB (LONG KEY)
1000 #--># D = SET THIS_KB_NO ON THE LOCAL KB (LONG KEY)

USER 1 (non multiuser mode)
1111 # 1A    = ARM BIT 1 OF CURRENT LEVEL                                     1111 # 5A   = ARM BIT 5 OF CURRENT LEVEL
1111 # 2A    = ARM BIT 2 OF CURRENT LEVEL                                     1111 # 6A   = ARM BIT 6 OF CURRENT LEVEL
1111 # 3A    = ARM BIT 3 OF CURRENT LEVEL                                     1111 # 7A   = ARM BIT 7 OF CURRENT LEVEL
1111 # 4A    = ARM BIT 4 OF CURRENT LEVEL                                     1111 # 8A   = ARM BIT 8 OF CURRENT LEVEL

1111 # AA = ARM LEVEL A      1111 # BA = ARM LEVEL B       1111 # CA = ARM LEVEL C    1111 # DA = ARM LEVEL D

1111 # 1B    = WARN BIT 1 OF CURRENT LEVEL                                    1111 # 5B   = WARN BIT 5 OF CURRENT LEVEL
1111 # 2B    = WARN BIT 2 OF CURRENT LEVEL                                    1111 # 6B   = WARN BIT 6 OF CURRENT LEVEL
1111 # 3B    = WARN BIT 3 OF CURRENT LEVEL                                    1111 # 7B   = WARN BIT 7 OF CURRENT LEVEL
1111 # 4B    = WARN BIT 4 OF CURRENT LEVEL                                    1111 # 8B   = WARN BIT 8 OF CURRENT LEVEL

1111 # AB = WARN LEVEL A       1111 # BB = WARN LEVEL B       1111 # CB = WARN LEVEL C       1111 # DB = WARN LEVEL D
1111 # # = DISARM SYSTEM                                              1111 # * = SHOW LAST 3 ALARMS

1111 #--># 1 = CHANGE PASSWORD USER 1 ON THE LOCAL KB (LONG KEY)
1111 #--># 2 = CHANGE PASSWORD USER 2 ON THE LOCAL KB (LONG KEY)
1111 #--># 3 = CHANGE PASSWORD USER 3 ON THE LOCAL KB (LONG KEY)
1111 #--># 4 = CHANGE PASSWORD USER 4 ON THE LOCAL KB (LONG KEY)
1111 #--># A = DIRECT PROGRAMMING OF TEL NO 2 (LONG KEY)
1111 #--># D = DISABLE/ENABLE THIS KEYBOARD
1111 #--># * = DIRECT MODE TO TRACER USING "1" & "2" KEYS (LONG KEY)

USERS 2,3,4 and... (5 for multiuser mode)
2222 #--># = CHANGE PASSWORD USER 2                            3333 #--># = CHANGE PASSWORD USER 3
4444 #--># = CHANGE PASSWORD USER 4                            5555 #--># = CHANGE PASSWORD USER 4

2222 # A     = ARM LEVEL B                                       2222 # #   = DISARM LEVEL B
3333 # A     = ARM LEVEL C                                       3333 # #   = DISARM LEVEL C
4444 # A     = ARM LEVEL D                                       4444 # #   = DISARM LEVEL D
5555 # A     = ARM LEVEL A                                       5555 # #   = DISARM LEVEL A


                                       DOUBLE KEY (special keys)
 * & # --> * & # = PANIC        (LONG KEY)                                           7 & 9 --> 6 & 9 = TEST   (LONG KEY)
 4 & 6 --> 4 & 7 = LIGHTS       (LONG KEY)                                           1 & 3 --> 1 & 3 = MEDICAL (LONG KEY)

intercom/camera scanning
  A+0 = ALL intercoms (relays) OFF (only with KEYBOARDS-R( with relays)
  A+1 = intercom (relay) 1 (only with KEYBOARDS-R( with relays) A+2 = intercom (relay) 2 (only with KEYBOARDS-R( with relays)
  A+3 = intercom (relay) 3 (only with KEYBOARDS-R( with relays) A+4 = intercom (relay) 4
  A+5 = auto scanning of relays (intercoms)
  *+6 to *+D = spare functions



                                                                        -12-

				
DOCUMENT INFO
Shared By:
Categories:
Stats:
views:27
posted:3/9/2011
language:English
pages:13