Docstoc

HEAT WELDED SHEET VINYL

Document Sample
HEAT WELDED SHEET VINYL Powered By Docstoc
					2010    HEAT WELDED SHEET VINYL

                                                                                   Page 1 of 10

PART 1 - GENERAL

1.01           SECTION INCLUDES

A.     Heat welded solid vinyl sheet flooring, complete with accessories. All heat welded sheet
       vinyl shall meet Erlanger Health System standards.
              1.     Coordinate the requirements of this section with Section 01010 Summary of
                     Work.

1.02           REFERENCE STANDARDS

A.     ASTM E84 - Surface Burning Characteristics of Building Materials.
B.     FS L-F-1641 - Floor Covering, Translucent or Transparent Vinyl Surface, with Backing.
C.     FS L-F-475 - Floor Covering, Vinyl Surface (Tile and Roll), with Backing.
D.     FS SS-T-312 - Tile, Floor: Asphalt, Rubber, Vinyl, Vinyl Composition.
E.     ASTM-D1044: No wear thru with 1000 gram weight at 20,000 cycles.
F.     ASTM-d4060: taber abraser using H-22 wheel under a 1000 gram load
G.     ASTM-E648 / NFPA 253: Critical Radiant Flux Class I not less than 0.45 W/cm2
H.     ASTM-662 / NFPA 258: Smoke developed 450 or less.

1.03           SUBMITTALS

A.     Submit following in accordance with Section 01340.
B.     Manufacturer's Product Data: Describing physical and performance characteristics, sizes,
       patterns and colors available for heat welded sheet flooring.
C.     Samples: 2" x 2" in size, illustrating the available colors and patterns for sheet flooring.
               1.     Include samples of welding rods in available colors.
D.     Installation Instructions: Describing manufacturer's recommendations for installation of
       sheet flooring.

1.04           OPERATION AND MAINTENANCE DATA

A.     Submit cleaning and maintenance data.
B.     Include maintenance procedures, recommended maintenance materials, and suggested
       schedule for cleaning.

1.05           ENVIRONMENTAL REQUIREMENTS

A.     Store materials for three days prior to installation in area of installation to achieve
       temperature stability.
B.     Maintain ambient temperature required by adhesive manufacturer three days prior to,
       during, and 24 hours after installation of materials.




2010 SVSPEC.                                                                              1
2010 HEAT WELDED SHEET VINYL

                                                                                    Page 2 of 10

1.06           DELIVERY AND STORAGE

A.     Sheet flooring materials shall be delivered in original unopened packages bearing
       Manufacturer's labels in accordance with Section 01605.
B.     Store and protect materials in accordance with Section 01605.

1.07           QUALITY ASSURANCE

A.     Install heat welded resilient flooring in accordance with floor manufacturer specifications.
B.     Installer shall be certified in writing by manufacturer.

1.08        WARRANTY
A.     Manufacturer 5 years


PART 2 - PRODUCTS

2.01   HEAT WELDED SHEET VINYL
       Acceptable manufacturers:

       A.      Johnsonite Collage Optima
               1.   Color to be selected.

       B.      Mannington Biospec/Fine Fields
               1.   Color to be selected.

       C.      Mannington Natures Path (Plank)
               1.   Color to be selected.

       D.      Mannington Realities
               1.   Color to be selected.

       E.      Toli Mature
               1.    Color to be selected.

       F.      Toli Lightwood (Plank)
               1.     Color to be selected.

       G.      Armstrong Medintone/Medintech
               1.   Color to be selected.

       H.      Armstrong Timberline
               1.   Color to be selected.

       J.      No substitutions will be allowed.




2010 SVSPEC.                                                                               2
2010    HEAT WELDED SHEET VINYL

                                                                            Page 3 of 10

2.02   BASE:        Integral coved base, not separate
            1.      Height: 4 IN.
            2.      Cap strip
            3.      Cove fillet

2.03. ADHESIVE
      Comply with EPA VOC regulations

2.04   TRANSITION STRIPS: 1IN wide rubber or PVC tapered to meet abutting material.

PART 3 - EXECUTION

3.01           PREPARATION

A.     Before installing sheet flooring:
              1.       Concrete surfaces shall be smooth and flat with maximum variation of 1/8
                       inch in 10 ft. and ready to receive flooring materials.
              2.       Concrete floors shall be dry to a maximum moisture content of 7 percent, and
                       exhibit negative alkalinity, carbonization, or dusting.
B.     Beginning of installation means acceptance of substrate and site conditions.
C.     Remove ridges and bumps from concrete surfaces. Fill low spots, cracks, joints, holes and
       other defects with subfloor filler.
D.     Apply, trowel, and float the filler to leave a smooth, flat, hard surface.
E.     Prohibit traffic from area until filler is cured.
F.     Vacuum clean the substrate.
G.     Prepare and prime surfaces in accordance with manufacturer's published instructions.

3.02           INSTALLATION

A.     Install heat welded sheet flooring and integral base in accordance with manufacturer's
       published instructions.
               1.     Install cover fillet strips at floor/wall intersections with adhesive.
               2.     Turn flooring material up the walls and set in adhesive.
               3.     Carefully miter corners and heat weld the seams.
               4.     Install cap strip at top of integral base.
B.     Spread only enough adhesive to permit installation of sheet flooring before initial set.
C.     Set sheet flooring in place, press with heavy roller to attain full adhesion.
D.     Terminate sheet flooring at centerline of door openings where adjacent floor finish is
       dissimilar.
E.     Edge Strips: Install at unprotected or exposed edges, and where sheet flooring terminates.
F.     Scribe sheet flooring to walls, columns, cabinets, floor outlets, and other appurtenances to
       produce tight joints.
G.     Sheet flooring shall be installed over covers for telephone conduits, electrical conduits and
       other similar items which occur within finished floor areas.
               1.     Sheet flooring MUST be cut sharp and clean around these covers so that
                      covers can be removed when required.
               2.     The sheet flooring must be applied to covers in a solid application of
                      adhesive.

2010 SVSPEC.                                                                               3
2010    HEAT WELDED SHEET VINYL

                                                                       Page 4 of 10

3.03           PROTECTION AND CLEANING

A.     Remove excess adhesive from sheet flooring surfaces without damage.
            1.    Clean surfaces in accordance with manufacturer's instructions.

END OF SECTION




2010 SVSPEC.                                                                          4
                                                                                  Page 5 of 10

                             2010    HEAT WELDED SHEET VINYL
                                      GENERAL NOTES


-      The following is Erlanger Health System's standard heat welded sheet vinyl selection.

-      This finish is determined by the Erlanger Health System's Interior Designer.

-      Any adjustments needed after a project begins will be handled by a change order (either
       an increase or decrease).

-      Glue and reducer strips will need to be added into the LABOR TO INSTALL item to be
       included in the Total Unit Price.

-      Do NOT add in removal of existing materials, floor prep/patch work, cleaning, waxing and
       protection of new materials.

-      Do NOT add in removal of furniture and equipment.

       The Markup percentage line item should be shown as both dollars and percentage.



       Unit Price Clarification:

       1. The total quantity of sheet vinyl square yards for a project will include the following:
               A. Borders
               B. Cove base to the top of the base
       The price for border work will only include extra labor per LFT of border
       The price for cove base per LFT will only include items other than the yards of sheet vinyl.
       The line item for freight will be determined by the bidder for all STANDARD material items.
       The second line under the TOTAL UNIT PRICE is to include a cut charge for less than
       minimum roll material as required by the manufacturer.
       This line item should NOT be used as a small quantity surcharge

       NON STANDARD BID CALCULATION

       Use the following for NON STANDARD ONLY:

       Material price: - The actual invoice cost of the HWSV from the manufacturer will be paid
       For this bid evaluation, assume the material cost of $20.00 / sq yd.
       Freight: estimated cost per yd (assume $x.xx), Actual Freight will be paid from attached
       invoice NO Markup will be ADDED.
       Use less than 50 yards as the cut charge breakpoint Manufactures actual will be paid




2010 SVSPEC.                                                                             5
2010     HEAT WELDED SHEET VINYL                 BIDDER: __________________________

                                      MATERIAL AND LABOR


NON - STANDARD HEAT WELDED SHEET VINYL
(All other than standard HWSV)
6’-6” wide (Roll)
        Material unit price (Actual Invoice will be paid)   $     20.00     /SQYD

       Labor to install                                                     /SQYD

       Markup percentage                                    $               (        %)

       Tax                                                                  (9.25%)

       Freight       (Actual invoice will be paid)          $     0.75      /SQYD

                     Total Unit Price                       $               /SQYD

                                                            $    N/A        /SQYD



STANDARD HEAT WELDED SHEET VINYL
Johnsonite Collage Optima 6’-6” wide (Roll)
     Material unit price                                                    /SQYD

       Labor to install                                                     /SQYD

       Markup percentage                                    $               (        %)

       Tax                                                                  (9.25%)

       Freight                                                              /SQYD

                     Total Unit Price                       $               /SQYD

                     Less than______sqyds Add for cut charge $              /SQYD




2010 SVSPEC.                                                                     6
2010     HEAT WELDED SHEET VINYL               BIDDER: ______________________________


STANDARD HEAT WELDED SHEET VINYL
Mannington Biospec/Fine Fields 6’-0” wide (Roll)
      Material unit price                                                 /SQYD

       Labor to install                                                   /SQYD

       Markup percentage                                   $              (        %)

       Tax                                                                (9.25%)

       Freight                                                            /SQYD

                     Total Unit Price                      $              /SQYD

                     Less than______sqyds Add for cut charge $            /SQYD



STANDARD HEAT WELDED SHEET VINYL
Mannington Natures Path (Plank)
     Material unit price                                                  /SQYD

       Labor to install                                                   /SQYD

       Markup percentage                                    $             (        %)

       Tax                                                                (9.25%)

       Freight                                                            /SQYD

                     Total Unit Price                       $             /SQYD

                     Less than______sqyds Add for cut charge $            /SQYD




2010 SVSPEC.                                                                   7
2010     HEAT WELDED SHEET VINYL                BIDDER: ______________________________


STANDARD HEAT WELDED SHEET VINYL
Mannington Realities 12’-0” wide (Roll)
     Material unit price                                                   /SQYD

       Labor to install                                                    /SQYD

       Markup percentage                                     $             (        %)

       Tax                                                                 (9.25%)

       Freight                                                             /SQYD

                     Total Unit Price                        $             /SQYD

                     Less than____sqyds Add for cut charge   $             /SQYD



STANDARD HEAT WELDED SHEET VINYL
Toli Mature 6’-0” wide (Roll)
      Material unit price                                                  /SQYD

       Labor to install                                                    /SQYD

       Markup percentage                                     $             (        %)

       Tax                                                                 (9.25%)

       Freight                                                             /SQYD

                     Total Unit Price                        $             /SQYD

                     Less than____sqyds Add for cut charge   $             /SQYD




2010 SVSPEC.                                                                    8
2010     HEAT WELDED SHEET VINYL                BIDDER: ______________________________


STANDARD HEAT WELDED SHEET VINYL
Toli Lightwood (Plank)
       Material unit price                                                 /SQYD

       Labor to install                                                    /SQYD

       Markup percentage                                     $             (        %)

       Tax                                                                 (9.25%)

       Freight                                                             /SQYD

                     Total Unit Price                        $             /SQYD

                     Less than____sqyds Add for cut charge   $             /SQYD



STANDARD HEAT WELDED SHEET VINYL
Armstrong Medintone/Medintech (Roll)
     Material unit price                                                   /SQYD

       Labor to install                                                    /SQYD

       Markup percentage                                     $             (        %)

       Tax                                                                 (9.25%)

       Freight                                                             /SQYD

                     Total Unit Price                        $             /SQYD

                     Less than____sqyds Add for cut charge   $             /SQYD




2010 SVSPEC.                                                                    9
2010     HEAT WELDED SHEET VINYL                 BIDDER: ______________________________


STANDARD HEAT WELDED SHEET VINYL
Armstrong Timberline (Roll)
     Material unit price                                                         /SQYD

       Labor to install                                                          /SQYD

       Markup percentage                                       $                 (       %)

       Tax                                                                       (9.25%)

       Freight                                                                   /SQYD

                      Total Unit Price                         $                 /SQYD

                      Less than____sqyds Add for cut charge    $                 /SQYD



MISC ITEMS


Border work/color (Doesn’t include intricate design)          $ ________________ /LFT
  (ADDED Labor only; weld material only)
  (sheet vinyl material cost is in above sq yds)


Flash coving                                                  $ ________________ /LFT
   (sheet vinyl material cost is in above sq yds)


Night Shift Differential            Labor ADD                 $ ________________ / SQ YD


Saturday Differential               Labor ADD                 $ ________________ / SQ YD


Sunday and Holiday Differential     Labor ADD                 $ ________________ / SQ YD




2010 SVSPEC.                                                                            10

				
DOCUMENT INFO