Blank Poster Presentation Template Symposium on Recent and Emerging Advances in Chemical by wbb39366


More Info
									Symposium on Recent and Emerging Advances in Chemical Engineering (REACH), Indian Institute of Technology Madras, Chennai,
India. December 2-4, 2010.

                                   Title in Title Case
                      (Each Word of the Title Should be Capitalised)

                                     Name Surname 1, Name Surname 2
                                         Department/ Division/Centre
                                        Institute/ University/ Company
                                   123 Main Street, City, Code City, Country


       This file provides a template for the extended abstract for poster presentation at the REACH
symposium. The proceedings will be published in an electronic format. The extended abstract in
MS Word file shall be written in compliance with these instructions.
       The main text of the extended abstract can be divided into sections. The paper length,
including figures, tables and references should not exceed 2 pages. Papers are to be prepared in
English (British or American) and SI-units shall be used. Acronyms should be written out at their
first appearance.
       Reference numbers in the text should be designated by square brackets, e.g., [1-4]. The
references should be listed in the same order as cited in the text. See also examples in the
REFERNCES section of this template [1-4].

          PAPER FORMAT

       The authors should use this template file to write their extended abstract. Please note the
following details: this template is on A4 page format with 20 mm margins on left, right, top and
bottom. Header and footer shall be positioned 16 mm from the edge.
       All text paragraphs should be single spaced, with first line intended by 10 mm. Double
spacing should only be used before and after headings and subheadings as shown in this example.
Position and style of headings and subheadings should follow this example. No spaces should be
placed between paragraphs. Please DO NOT change any of the above mentioned page, paragraph
and font settings. Papers should use 12-point Times New Roman font. The styles available are bold,
italic and underlined. It is recommended that text in figures is not smaller than 9-point font size.

          Tables and Figures

      Figure captions and table headings should be sufficient to explain the figure or table without
needing to refer to the text. Figures and tables not cited in the text should not be presented. The
following is the example for Table 1. Table headings should be centred above the tables.

                                         Table 1 Title of Example Table
                                            Header                          X            Y
                          Test 1                                            1           Yes
                          Test 6                                            6           No

      All figures and tables should be numbered with Arabic numerals. Figure captions should be
centred below the figures. An example is shown in Figure 1.

Figure 1: Conductivity of blend membranes as a function of weight % of poly vinyl alcohol (PVA)


      Each equation should be presented on a separate line from the text with a blank space above
and below. Equations should be clear and expressions used should be explained in the text. The
equations should be numbered consecutively at the outer right margin, as shown in Eq. (1) below:
Following are examples of equations:

         ( 
          k )! k                                                                          (1)
        
      k1 ( 1m)!


     This section should state the most important conclusions of the paper. The manuscript can be
submitted electronically on or before October 15, 2010, by e-mail to the address


[1] E. Gulzow, M. Schulze, N. Wagner, J. Power Sources 86 (2000) 352-362.

[2] L.J. Blomen, M.N. Mugerwa, Fuel Cell Systems, Plenum Press, 1993.

[3] T. Uemura, S. Murakami, US patent 4,737,421, 12 April (1988).

[4] M. Iwase, S. Kawatsu, Optimized CO tolerant electrocatalysts for polymer electrolyte fuel cells,
    in: Proceedings of the First International Symposium on Proton Conducting Membrane Fuel
    Cells, vol. 1, 1995, 12-18.


To top