Sony Kp53V25 Projection Tv

Document Sample
Sony Kp53V25 Projection Tv Powered By Docstoc
					Sony KP41T65         Chassis RA2A

Looks like AGC overload on live video. Test patterns OK.

C5145 10uf50v located on the PT board

Wayne Vanaman
Omega Electronics
6904 W Fairfield Dr
Pensacola, Fl. 32506-3310



Sony PTV is a 1998 model KP41T65.
The set will not turn on until about the 3rd, or 4th try.
When the picture comes in, it is in from both sides about 2 inches, and
Down from the top, and up from the bottom about 2 inches. After about 5 minutes,
the picture finally fills the screen, but it looks a little milky, or some
what out of focus. They say if it is left on too long, it will shut
off

A can of circuit coolant lead me straight to C655 (2200 ufd. @ 25VDC), on
power supply module. Read about 1650 ufd. when cold, and about 1850 ufd.
after heated up.
LeRoy Westlund




         KP41T65

         Subject
         ANODE AND HV LEAD P/N




       SYMPTOMS

       What are the part numbers for the anode and focus leads?

       RESOLUTION

       Anode 1-779-095-21
       Focus Lead 1-900-231-42
  KP41T65

  Subject
  NO AUDIO, IC403


SYMPTOMS

No audio,

RESOLUTION

IC403 defective. Replaced IC403 or the A Board. Your assistance is need
to obtain the necessary information to find the solution to this failure..
Please contact your Tech Rep. with the information required below.

The Vcc of audio amp may be higher than expected.
Vcc is provided from PIT but no regulator in this line so the voltage varies
by a variation of PIT winding. To verify that we want to know the voltage of
Vcc.
Please measure the voltage between pin 9(Vcc) and pin 3(GND) of IC404.
It's supposed to be around 30V. If our assumption is correct then
additional diode in Vcc line will help an IC404 failure. Design will
determine type of diode and the location of the insertion.



  KP41T65, KP46C65

  Subject
  P/N FOR IC5052 INCORRECT, 875953389


SYMPTOMS

P/N for IC-5052 in the S/M 8-759-487-47 comes up no longer available in
the system.

RESOLUTION

The correct P/N is 8-759-533-89.



  KP53S15, KP53S25, KP53S55, KP53S65, KP53V15, KP53V16, KP53V25, KP53V35 ,
  KP53V45, KP53V75, KP53V90, KP53XBR200, KP53XBR35, KP53XBR45,
  KP53XBR4CT
  Subject
  L and F Screens Sub


SYMPTOMS

The L Screen is No Longer Available. Is there a sub?

RESOLUTION

Both the L screen and F Screen must be replaced with the part numbers
below.

Failure to replace both screens will cause picture degrading.

Change screens to Part Numbers:

L Screen 4-070-525-01
F Screen 4-084-702-02




  KV27FV300, KV32FV300, KV36FV300

  Subject
  Picture blinked no luminance


SYMPTOMS

Picture blinked on and off but no luminance.

CAUSE

Problem look like unit had bad connection on the BC board check pin 7 of
CN306 (Y signal) good, but CN306/pin 12 no luminance out. Checked
CN306/pin 16, 14v missing !

14v come from GK board CN605 pin1 . 14v missing found PS601open
replace fixed .
Service manual is wrong Cn 605 pin 1 on the GK board show 5v it
incorrect should be 14v and pin 2 should be 5v

RESOLUTION
       Found PS601open replace fixed .

       Service manual is wrong CN605/pin 1 on the GK board show 5v it's
       incorrect.
       Should be 14v and CN605/pin 2 should be 5v

Part Number              Referenc e Number                Description
157633721                PS601                            Link IC




         KP41T65

         Subject
         AUX PICTURE S NOW Y, IC001


       SYMPTOMS

       Aux picture is snowy.

       RESOLUTION

       Found IC001 on the A Board defective.

Part Number              Referenc e Number              Description

8-752-894-96             IC001                          CXP85856A-




         KP41T65

         Subject
         DEAD, Q502


       SYMPTOMS

       Dead.

       RESOLUTION

       Replaced Q502 on the G Board.
Part Number                  Referenc e Number                  Description
8-729-024-05                 Q502                               2SD2348




         KP41T65

         Subject
         DEAD, T504


       SYMPTOMS

       Dead.

       RESOLUTION

       Found T504 defective on the G Board.

Part Number                  Referenc e Number                  Description
1-453-238-11                 T504                               FBT




         KP41T65

         Subject
         DEAD, T605


       SYMPTOMS

       Primary input okay, extremely low secondary outputs.

       RESOLUTION

       Found the secondary windings T605/pin 9 -12 shorted to windings
       T605/pin 13-14.
       Replaced T-605

Part Number           Referenc e Number           Description
142998511             T605                        CONVERTER (PIT)
         KP41T65

         Subject
         PICTURE JUMPI NG, IC808


       SYMPTOMS

       Picture jumping.

       RESOLUTION

       Replaced IC808 on the G Board.

Part Number               Referenc e Number                  Description

8-759-464-79              IC808                              PM0011AS




         KP41T65

         Subject
         SHUTS DOWN, IC601, R608


       SYMPTOMS

       Unit shuts down.

       RESOLUTION

       Found IC601 & R608 defective on the G Board.

Part Number           Referenc e Number        Description
8-729-041-12          IC601                    0.1 OHM FUS E 1/2W

1-202-933-61          R608                     0.1 OHM FUS E 1/2W
         KP41T65

         Subject
         SHUTS DOWN, R586


       SYMPTOMS

       Unit shuts down.

       RESOLUTION

       Found R586 on the G Board defective.

Part Number                Referenc e Number                  Description

1-260-292-11               R586                               1 OHM 1/2W




         KP41T15,   KP41T25, KP41T35, KP41T65, KP43T70, KP46C36, KP46C65, KP46C70,
         KP46S15,   KP46S17, KP46S25, KP46V25, KP46V35, KP48S35, KP48S65, KP48S72,
         KP48V45,   KP48V75, KP53S15, KP53S17, KP53S25, KP53S35, KP53S65, KP53V25,
         KP53V35,   KP53V45, KP53V75, KP53XBR45, KP61S35, KP61S65, KP61V25,
         KP61V35,   KP61V45, KP61V75, KP61XBR48

         Subject
         UP DATE OF THE NVM JIG I/M, GEN S B31


       SYMPTOMS

       If the need should arise that a circuit board needs to be replaced, It might
       contain an EEPROM. If the EEPROM data is not written into the EEPROM
       of the replacement board all the service or customer adjustments will be
       lost. Example: Convergence adjustments. This will then require additional
       time to re-converge a projection TV.



       RESOLUTION

       Refer to SB GENTVP E08921219 for NVM Jig connections. Also refer to
       the NVM Instruction Manual for operating instructions E16415167 or TV
       SB449. The I/M will not address all chassis since it was written prior to
       RA-6 and DA4 chassis. The SB E08921219 contains the settings for all
       chassis.
  KP41T65

  Subject
  Two types of CRTs Used


SYMPTOMS

Two types of CRTs Used

RESOLUTION

If you need to replace the CRT please refer to the chart below for the
correct CRT needed.
CRT Serial Number Range 9000001-9018822
Red 8-733-539-05
Blue 8-733-519-05
Green 8-733-537-05

Serial Number Range 9500001-9534348
Red A-1501-367-A
Blue A-1501-369-A
Green A-1501-372-A
NOTE: Due to the CRT change some boards were also changed. Please
see the
attached SB below before ordering any boards.

SUPPORTING DOCUMENTS AND GRAPHICS



                                                       Name: SB400R1.pdf
                                                       Description: SB400R1




  KP41T65

  Subject
  Unit in shutdown


SYMPTOMS
       Unit is dead.

       CAUSE

       No HV, TV just clicks. Found B+ voltage 135v. Source reading 10v and
       diode D655 getting hot. Disconnect 220v source to CB PCB and HV
       restored.
       Found shorted video IC761. Replaced and solved problem.



       RESOLUTION

       No HV, TV just clicks. Found B+ voltage 135v. Source reading 10v and
       diode D655 getting hot. Disconnect 220v source to CB PCB and HV
       restored.
       Found shorted video IC761. Replaced and solved problem.


Part Number                Referenc e Number                  Description
875943439                  314                                CB Board




         KP41T65, KP46C65, KP48S65, KP48S65R, KP48V45, KP48V75, KP48V75, KP53S65,
         KP53V45, KP53V75, KP53V75, KP61S35, KP61S65, KP61V45, KP61V75, KP61V75

         Subject
         Repeat failures of the audio amplifier


       SYMPTOMS

       We are having a continuing problem with the RA-2 chassis models. We
       get a no audio situation and find the Audio Amp TA8216H (IC404) shorted
       and PS401 open. We replace both components and the unit works fine for
       anywhere from 3 to 6 months.


       RESOLUTION

       You assistance is need to obtain the necessary information to find the
       solution to this failure.. Please contact your Tech Rep with the information
       required below.
       The Vcc of audio amp may be higher than expected.
       Vcc is provided from PIT but no regulator in this line so the voltage varies
       by a variation of PIT winding. To verify that we want to know the voltage of
       Vcc.
       Please measure the voltage between pin 9(Vcc) and pin 3(GND) of IC404.
       It's supposed to be around 30V. If our assumption is correct then
       additional diode in Vcc line will help an IC404 failure. Design will
       determine type of diode and the location of the insertion with the
       information supplied from the servicers.


Part Number            Referenc e Number           Description
8-759-168-24           IC404                       Audio Amp TA8216H
1-532-984-11           PS401                       IC 2A/90V




         KP41T65, KP46C65, KP48S65, KP48V75, KP53S65, KP53V75, KP61S65, KP61V75

         Subject
         Repeat failures of the audio amplifier


       SYMPTOMS

       We are having a continuing problem with the RA-2A chassis models. We
       get a no audio situation and find the Audio Amp TA8216H (IC404) shorted
       and PS401 open. We replace both components and the unit works fine for
       anywhere from 3 to 6 months.


       RESOLUTION

       Your assistance is needed to obtain the necessary information to find the
       solution to this failure. Please contact your Tech Rep with the information
       required below.

       The Vcc of audio amp may be higher than expected.
       Vcc is provided from PIT but no regulator in this line so the voltage varies
       by a variation of PIT winding. To verify that we want to know the voltage of
       Vcc.
       Please measure the voltage between IC404/pin 9 (Vcc) and pin 3 (GND)
       of IC404 or IC403 Audio Amp . It's supposed to be around 30V. If our
       assumption is correct then additional diode in Vcc line will help an IC404
       failure. Design will determine type of diode and the location of the insertion
       with the information supplied from the servicers.

       NOTE: Since we never received the requested information from the field
       no diode or circuit mod was created for this continuing failure. The
       information requested would have giving the engineering the details they
       needed to confirm there opinion that the voltage might be too high but
       with no feedback they could not tell if their guess was correct or not.


Part Number           Referenc e Number             Description
8-759-168-24          IC404                         Audio Amp TA8216H
1-532-984-11          PS401                         IC 2A/90V




         KP41T15, KP41T25, KP41T35, KP41T65, KP43HT20, KP43T70, KP43T75, KP43T90,
         KP46C36, KP46C65, KP46C70, KP46S15, KP46S25, KP46V25, KP46V35, KP48S35,
         KP48S65, KP48S65R, KP48S70, KP48S72, KP48S72, KP48S75, KP48V45, KP48V75,
         KP48V80, KP48V85, KP48V90, KP51HW40, KP53HS20, KP53HS30, KP53N74,
         KP53S15, KP53S25, KP53S35, KP53S65, KP53S70, KP53S75, KP53V25, KP53V35,
         KP53V45, KP53V75, KP53V80, KP53V85, KP53V90, KP53XBR45 , KP53XBR4CT,
         KP57HW40, KP57XBR10W, KP61HS20, KP61HS30, KP61S65, KP61S70, KP61S75,
         KP61V25, KP61V35, KP61V45, KP61V75, KP61V80, KP61V85, KP61V90,
         KP61XBR48, KP65XBR10W

         Subject
         Focus Block Part Change


       SYMPTOMS

       The original Focus Block is no longer available.

       RESOLUTION

       If the Focus Block should need to be replaced the new sub P/N 1-223-
       925-31 should be used. The wire connections will be difference. See the
       diagram below for proper wiring.

       Description Former P/N New P/N
       Focus Block 1-223-925-11 1-223-925-31
       Focus Block 1-223-925-12 1-223-925-31
       Focus Block 1-223-925-81 1-223-925-31
       The -51 should sub to the -61 and has 11 connections. They should not
       sub to the -31 or -71 which have 10 connections. The -31 and -71 differ in
       the value of the resistors and should not sub as long as both are available.


       SUPPORTING DOCUMENTS AND GRAPHICS



                                                   Name: sb555.pdf
                                                   Description: Focus Block diagram
                                                   Size: 16226 bytes




         KP41T65, KP46C65, KP48S65, KP48V75, KP53S65, KP53V75, KP61S65, KP61V75

         Subject
         Exce ssive red on picture


       SYMPTOMS

       Excessive red on picture

       CAUSE

       Red drive too high. Red G2 voltage cannot be adjusted properly. Running
       red G2 through its normal range causes red to jump from blanked to
       retrace.

       RESOLUTION

       Replaced C315 red S/H cap. Cap measured OK with capacitor checker,
       but substituting C315 resolved the problem. Cap was causing excessive
       red drive.

       Located at IC301/pin 19.

Part Number             Referenc e Number               Description

113049500               C315                            0.1UF 50V Film
  KP41T65

  Subject
  CRT and board P/N change


SYMPTOMS

CRT and board P/N change

RESOLUTION

Please see the attached Supplement.

SUPPORTING DOCUMENTS AND GRAPHICS



                                                 Name: Suppleme.pdf
                                                 Description: Supplement1




  KP41T65, KP46C65, KP48S65, KP53S65, KP61S65

  Subject
  PN for C514 100pf and 680pf at 2kv


SYMPTOMS

The part number for C514 is not provided in the G board parts listing,
because it is one of those selected values, per HV adjustment procedures
on page 45. The values may be 100, 390, or 680 pf at 2KV. Need the P/N
for the 100PF and the 680PF at 2kv.



RESOLUTION

The P/N are:
680pf /2kv 1-162-116-00
100pF/2kv 1-107-444-11 ceramic disc cap
  KP46C65

  Subject
  CONTROL DOOR P/N CHANGE, X-403-445-62


SYMPTOMS

P/N 4-057-605-01, control door subs to NLA.

RESOLUTION

Order the control panel assy per the following X-403-445-62




  KP46C65

  Subject
  PART NUMBER ANODE & FOCUS LEAD


SYMPTOMS

What are the part numbers for the anode and focus leads?

RESOLUTION

Anode 1-779-095-21
Focus Lead 1-900-231-42




  KP46C65

  Subject
  DEAD, R610


SYMPTOMS

Dead.

RESOLUTION

Found R610 open on the G Board.
Part Number                  Referenc e Number                  Description
1-247-887-00                 R610                               220K 1/4W




         KP46C65

         Subject
         DEAD, R614


       SYMPTOMS

       Dead.

       RESOLUTION

       Found R614 on the G Board was defective.

Part Number           Referenc e Number           Description
1-247-887-00          R614                        220K 1/4W RESISTOR




         KP48S65, KP61S65

         Subject
         P/N FOR IC5052 INCORRECT, 8-759-533-89


       SYMPTOMS

       P/N for IC-5052 in the S/M 8-759-487-47 comes up no longer available in
       the system.

       RESOLUTION

       The correct P/N is 8-759-533-89.

Part Number             Referenc e Number               Description
8-759-533-89            IC5052                          SDA9288X-B121
         KP48S65

         Subject
         DEAD, IC601, R608, D662


       SYMPTOMS

       Dead.

       RESOLUTION

       Found IC601, R608, and D662 defective on the G Board.

Part Number          Referenc e Number       Description

8-719-991-33         D662                    ISS133T-77
8-729-041-12         IC601                   MX0841AB-F
1-202-933-61         R608                    FUS E 0.1 OHM 1/2W RESISTOR




         KP48S65

         Subject
         NO PICTURE, T504


       SYMPTOMS

       No Picture.

       RESOLUTION

       Found T504 defective on the G: Board.

Part Number                  Referenc e Number                 Description
1-453-238-11                 T504                              FBT
         KP48S35, KP48S35, KP48S35, KP48S65

         Subject
         NO V ERTI CAL, PS601 & PS602


       SYMPTOMS

       No vertical.

       RESOLUTION

       Found PS601 & PS602 open on the G Board.

Part Number                Referenc e Number           Description
1-533-597-21               PS601                       LINK IC
1-533-597-21               PS602                       LONK IC




         KP48S65

         Subject
         POOR CONVERGENCE, IC803.


       SYMPTOMS

       Poor convergence.

       RESOLUTION

       Replaced IC803 on the G Board.

Part Number             Referenc e Number         Description
8-759-183-37            IC1803                    Shading Amp.




         KP53S65
         Subject
         POOR PICTURE, MIRROR BROKEN


       SYMPTOMS

       Poor picture.

       RESOLUTION

       Broken mirror.

Part Number                 Referenc e Number                Description
4-048-181-01                80                               MIRROR




         KP53S65

         Subject
         P/N FOR IC5052 INCORRECT, 8-759-533-89.


       SYMPTOMS

       P/N for IC-5052 in the S/M 8-759-487-47 comes up no longer available in
       the system.

       RESOLUTION

       The correct P/N is 8-759-533-89.




         KP53S65, KP53V75

         Subject
         DAMAGED PIX TUBES


       SYMPTOMS

       A dab of what appears to be a clear silicon compound is applied to the
       junction of the CRT pins and sockets, to prevent the C boards from getting
       loose, it seems like the new models are receiving an excessive application
       of this compound making it very difficult to remove the C boards for
       service. When tech use a blade to cut exposed portion, enough of this
       compound has penetrated in front of the socket, preventing a gentle
       separation from the tube causing the frequent rupture of the CRT tip.
       HQ: Pittsburgh will reduce this compound to prevent this damage.

       SYMPTOMS

       CRT Board very hard to remove causing damage to the CRT.

       RESOLUTION

       We continue to investigate this issue




         KP53S65

         Subject
         DARK OR NO PICTURE, R586


       SYMPTOMS

       Dark or no picture. -Found R586 on the G Board defective. Located off
       FBT/pin4 (200V)

       RESOLUTION

       We continue to investigate this issue

Part Number                  Referenc e Number              Description
1-206-292-11                 R586                           1 OHM 1W




         KP53S65

         Subject
         DEAD, T504 & Q502


       SYMPTOMS
       Dead.

       RESOLUTION

       FBT (T504) and Q502 defective on the A Board.

Part Number                  Referenc e Number                 Description

8-729-024-05                 Q502                              2SD2348

1-453-238-11                 T504                              FBT




         KP53S65

         Subject
         DEAD, T603


       SYMPTOMS

       Dead.

       RESOLUTION

       Replaced defective T603 on the G Board.

Part Number           Referenc e Number          Description
1-423-665-11          T603                       POWER TRANSFORMER




         KP53S65

         Subject
         IK BLANKING STANDBY LED FLASHI NG, D763


       SYMPTOMS

       While in Ik blanking the screen would intermittently flash on and off with a
       bright cyan raster about every 15 seconds, or it might just stay blank. All
       three Ik pulses looked normal. Sound was normal.
       RESOLUTION

       All three Ik pulses looked normal. Sound was normal.

       Replace D763 10v 1/2 watt zener located off of IC761/pin 5 on the Blue
       CRT drive board. For testing purposes, lift one end of diode to see if
       restores operation. Our diode tested good with an ohm meter. This same
       diode is used on red & green CRT boards, D708 and D733. Lifting one
       end of D763 doesn't correct problem, you can try this same test for D708
       and D733.

Part Number               Referenc e Number                Description
871911017                 D763                             RD1OESB2




         KP53S65

         Subject
         INTERMITTENT CONV ERGENCE, IC007


       SYMPTOMS

       Intermittent Convergence.

       RESOLUTION

       Replaced IC007 on the A Board.

Part Number                 Referenc e Number                 Description

8-759-518-23                IC007                             EEPROM




         KP53S65

         Subject
         POOR PIN, D528


       SYMPTOMS
       Poor pincushion.

       RESOLUTION

       Found D528 located on IC501/pin1 defective on the G Board.

Part Number               Referenc e Number            Description

8-719-923-86              D528                         MTZJ-T-77-15




         KP53S65

         Subject
         SHUTS DOWN, X5051


       SYMPTOMS

       Unit shuts down.

       RESOLUTION

       Replaced X5051 on the PT Board.

Part Number                Referenc e Number               Description
1-760-095-21               X5051                           CRYSTAL




         KP53S65

         Subject
         SNOWY PICTURE, TUNER


       SYMPTOMS

       Snowy picture.

       RESOLUTION

       Replaced the tuner on the A Board.
Part Number                 Referenc e Number                Description
8-598-340-00                TU1101                           TUNER




         KP53S65

         Subject
         VERTICAL POSITION INCORRECT, C337


       SYMPTOMS

       Vertical position incorrect.

       RESOLUTION

       Found C337 on the A Board defective.

Part Number                 Referenc e Number                Description
1-126-960-11                C337                             1UF 50V




         KP53S65

         Subject
         blue off center


       SYMPTOMS

       Blue was off center by two inches and centering could not be adjusted.

       CAUSE

       IC804 on the G board was defective.


       RESOLUTION

       IC804 on the G board was defective.
Part Number              Referenc e Number                   Description
875946479                IC804                               B CONV.




         KP61S65

         Subject
         INTERMITTENT SHUTDOWN, CN8007


       SYMPTOMS

       Intermittent shutdown.

       RESOLUTION

       Found cold solder joint on CN8007. Resoldered CN8007 on the D Board.




         KP61S65

         Subject
         MIRROR P/N INCORRECT, 4-058-643-01


       SYMPTOMS

       The part number for the mirror, Ref 111, listed on page 91 of the Service
       Manual is incorrect.

       RESOLUTION

       The correct part number is 4-058-643-01.




         KP61S65

         Subject
         SCREEN ACCESSORY
SYMPTOMS

Which model do the SCN-61X2 Fit?

RESOLUTION

This is for the KP-61S65.




  KP61HS10, KP61S35, KP61S65, KP61S70, KP61S75, KP61V15, KP61V25, KP61V35,
  KP61V45, KP61V80, KP61V85, KP61XBR200, KP61XBR300, KP61XBR38

  Subject
  Screen No Longer Available


SYMPTOMS

Screens No Longer Available
(L) 4-040-124-11
(F) 4-040-123-11

(L) 4-070-283-11
(F) 4-066-082-01

RESOLUTION

If one of the screens is No Longer Available then it is recommended to
replace both Fresnel and Lenticular with the P/Ns below to achieve
satisfactory result.

Fresnel 4-084-704-01
Lenticular 4-070-283-01




     Mode l KP41T65: Features

      PEDISTAL C LAMP YES
      AUTO WHITE BAL YES
      BRIGHTNESS 720 FT LAMBER TS
      COLOR FILTER DUAL CO LOR FILTER SYSTEM R ED & GR EEN
      DYNAMIC FOCUS YES
      DYNAMIC CRT DYNAMIC PICTUR E PROC ESSOR
SHADING CIRC YES
VELOCITY MO D YES
PROTEC T SCR EEN BUILT-IN HIGH CO NTR AST PROTECTIVE SCR EEN
MTS YES
MATR IX SURROUND YES
AUDIO POW ER 12 W ATTS X 2
SPEAKER O N/OFF YES
PIP YES
PIP FR EEZE FR EEZE MEMO
C HANNEL INDEX 12 C HANNELS
MULTI-LANGUAGE ENGLISH,SPANISH,FR ENCH
FAVORITE C HANEL 5 CHANNEL
C APTIO N VISIO N YES
C HANNEL C APTIO N YES
VIDEO LABEL YES
PRO GRAM TIMER YES
SLEEP 30,60,90 MINUTES
JUMP YES
SA-VA CO NTROL YES
XDS EXTENDED DATA SERVIC E
C HANNEL BLOC K YES
PRO GRAM PALETTESTANDARD,MO VIE,SPORTS
COLOR TEMP. TRINITO NE CO LOR TEMPER ATUR E ADJUSTMENT
BRIGHTVIEW DUAL CO MPO NENT SCR EEN
GAMMA COMPENSATYES
VIEWING ANGLE 130/55
VIDEO AMPLIFIERWIDEBAND
C HANNEL MAGIC 8 C HANNELS
CO NV ADJUSTMENTWITH R EMOTE




Mode l KP41T65: Specifications

C HANNEL COVER          181 CHANNEL
TUNING SYSTEM           EXPR ESS TUNING SYSTEM ( 181 CHANNEL )
PROJECTIO N LENS        MICROFOCUS LENS SYSTEM
INPUT                   2 R EAR AUDIO/VIDEO INPUTS, 1 S-VIDEO
INPUTS                  FRO NT AUDIO/VIDEO INPUTS WITH S-VIDEO
ANT INPUT               75 O HMS
OUTPUTS                 VARIABLE/FIXED AUDIO OUTPUTS
OUTPUTS                 MO NITOR
W EIGHT                 122 LBS
DIMENSIO NS             37 1/2 X 40 1/4 X 23 3/4 (W ,H,D)
R EMOTE CO NTRO L       RM-Y136A
COMB FILTER             3 LINE DIGITAL COMB FILTER
VIDEO PROC ESSOR        BI-POLAR VIDEO PROC ESSOR
AUDIO POW ER            24 W ATT AUDIO POW ER
ENER GY STAR            ENER GY STAR COMPLIANT
S VIDEO                 R EAR S VIDEO INPUT
S O UTPUT               NO
Mode l KP46C65: Spec ifications

C HANNEL COVER      VHF: 2-13, UHF: 14-69, C ATV 1-125
PROJ SYSTEM         3 PICTUR E TUBES, 3 LENSES
PROJECTIO N LENS    HIGH PER FORMANC E, LAR GE DIA HYBR ID LENS F 1.1
PICTUR E BR IGHT    7" HI-BRIGHTNESS MO NOCHRO ME TUBES
OPTIM VIEW AR EA    HOR IZ: 6 FT., VERT: 6 FT 20 DEGR EES L/R
INPUT               A/V W S-VIDEO , VIDEO/AUDIO 2, A/V W/S-VIDEO
ANT INPUT           75 O HM
OUTPUTS             AUDIO O UT PHO NO JAC KS, IMPEDANC E: 5KILO HMS
OUTPUTS             MO NITOR OUT: VIDEO/AUDIO
SPEAKER             FULL R ANGE 100 MM (3.9 IN) DIA
PWR R EQUIR EMENT   120V, 60 HZ
PWR CO NSUMPTIO N 165 WATTS, STANDBY MODE: 3 WATTS
W EIGHT             143 LBS 5 0Z (65 KG)
DIMENSIO NS         42 X 51 1/2 X 22 1/4" (1066 X 1306 X 563MM)
R EMOTE CO NTRO L   RMY136A
AUDIO POW ER        SPEAKER OUTPUT: 15 W X 2
ENER GY STAR        COMPATIBLE
S VIDEO             YES




Mode l KP48S65: Features

PEDISTAL C LAMP YES
AUTO WHITE BAL YES
BRIGHTNESS 550 FT LAMBER TS
COLOR FILTER DUAL CO LOR FILTER SYSTEM R ED & GR EEN
DYNAMIC FOCUS YES
DYNAMIC CRT DYNAMIC PICTUR E PROC ESSOR
SHADING CIRC YES
VELOCITY MO D YES
PROTEC T SCR EEN SC N48X2 ( OPTIO NAL )
MTS YES
MATR IX SURROUND YES
AUDIO POW ER 12 W ATTS X 2
SPEAKER O N/OFF YES
PIP YES
PIP FR EEZE SNAP SHOT SCR EEN FR EEZE
C HANNEL INDEX 12 C HANNELS
MULTI-LANGUAGE ENGLISH,SPANISH,FR ENCH
FAVORITE C HANEL 5 CHANNEL
C APTIO N VISIO N YES
C HANNEL C APTIO N YES
VIDEO LABEL YES
PRO GRAM TIMER YES
SLEEP 30,60,90 MINUTES
JUMP YES
SA-VA CO NTROL YES
XDS YES
C HANNEL BLOC K YES
PRO GRAM PALETTEPROGR AM PALLETTE (STANDAR D,MO VIE,SPORTS)
COLOR TEMP. HIGH,MEDIUM,NTC S STANDAR D
MIRROR FIR ST SURFAC E MIRROR
BRIGHTVIEW DUAL CO MPO NENT SCR EEN
GAMMA COMPENSATYES
VIEWING ANGLE 130/55
VIDEO AMPLIFIERWIDEBAND
C HANNEL MAGIC 8 FAVORITE CHANNELS
CO NV ADJUSTMENTWITH R EMOTE




Mode l KP48S65: Spec ifications

C HANNEL COVER        181 CABLE COMPATIBLE
PROJECTIO N LENS      MICROFOCUS LENS SYSTEM
PICTUR E BR IGHT      550 FT LAMBERTS
INPUT                 2 R EAR AUDIO/VIDEO INPUTS
INPUTS                1 FRO NT AUDIO/VIDEO INPUT WITH S-VIDEO
ANT INPUT             75 O HMS
OUTPUTS               VARIABLE/FIXED AUDIO OUTPUT
OUTPUTS               MO NITOR OUTPUT AND CO NTROL S OUTPUT
PWR R EQUIR EMENT     120V, 60 HZ
PWR CO NSUMPTIO N     165 W MAX, 2.5 STANDBY
W EIGHT               148 LBS APPRO X.
DIMENSIO NS           43 5/8 X 52 5/8 X 22 1/2 (W ,H,D)
C ABINET              GR AY
R EMOTE CO NTRO L     RMY 136A
COMB FILTER           3 LINE COMB FILTER CIRC UITRY
VIDEO PROC ESSOR      ADVANC ED VIDEO PROC ESSOR
AUDIO POW ER          12W X 2
ENER GY STAR          COMPATIABLE
S VIDEO               FRO NT AND BAC K S VIDEO INPUTS




Mode l KP48S65R: Features

PEDISTAL C LAMP YES
AUTO WHITE BAL YES
BRIGHTNESS 550 FT LAMBER TS
COLOR FILTER DUAL CO LOR FILTER SYSTEM R ED & GR EEN
DYNAMIC FOCUS YES
DYNAMIC CRT DYNAMIC PICTUR E PROC ESSOR
SHADING CIRC YES
VELOCITY MO D YES
PROTEC T SCR EEN SC N48X2 (INC LUDED)
MTS YES
AUDIO POW ER YES
SPEAKER O N/OFF 12 W ATTS X 2
PIP YES
PIP FR EEZE YES
C HANNEL INDEX SNAP SHOT SCR EEN FR EEZE
MULTI-LANGUAGE 12 CHANNELS
FAVORITE C HANEL ENGLISH,SPANISH,FR ENCH
C APTIO N VISIO N 5 CHANNEL
C HANNEL C APTIO N YES
VIDEO LABEL YES
PRO GRAM TIMER YES
SLEEP YES
JUMP 30,60,90 MINUTES
SA-VA CO NTROL YES
XDS YES




Mode l KP48S65R: Specifications

C HANNEL COVER        181 CABLE COMPATIBLE
PROJECTIO N LENS      MICROFOCUS LENS SYSTEM
PICTUR E BR IGHT      550 FT LAMBERTS
INPUT                 2 R EAR AUDIO/VIDEO INPUTS, COMPO NENT VIDEO
INPUTS                1 FRO NT AUDIO/VIDEO INPUT WITH S-VIDEO
ANT INPUT             75 O HMS
OUTPUTS               VARIABLE/FIXED AUDIO OUTPUT
OUTPUTS               MO NITOR OUTPUT AND CO NTROL S OUTPUT
PWR R EQUIR EMENT     120V, 60 HZ
PWR CO NSUMPTIO N     165 W MAX, 2.5 STANDBY
W EIGHT               148 LBS APPRO X.
DIMENSIO NS           43 5/8 X 52 5/8 X 22 1/2 (W ,H,D)
C ABINET              GR AY
R EMOTE CO NTRO L     RMY 136A
COMB FILTER           3 LINE COMB FILTER CIRC UITRY
VIDEO PROC ESSOR      ADVANC ED VIDEO PROC ESSOR
AUDIO POW ER          12W X 2
ENER GY STAR          COMPATIABLE
S VIDEO               FRO NT AND BAC K S VIDEO INPUTS




Mode l KP53S65: Features

PEDISTAL C LAMP YES
AUTO WHITE BAL YES
BRIGHTNESS 460 FT LAMBER TS
COLOR FILTER DUAL CO LOR FILTER SYSTEM R ED & GR EEN
DYNAMIC FOCUS YES
DYNAMIC CRT DYNAMIC PICTUR E PROC ESSOR
SHADING CIRC YES
VELOCITY MO D YES
PROTEC T SCR EEN SC N53X2 (OPTIO NAL)
MTS YES
MATR IX SURROUND YES
AUDIO POW ER 12 W ATTS X 2
SPEAKER O N/OFF YES
PIP YES
PIP FR EEZE FR EEZE MEMO
C HANNEL INDEX NO NE
MULTI-LANGUAGE ENGLISH,SPANISH,FR ENCH
FAVORITE C HANEL 5 CHANNEL
C APTIO N VISIO N YES
C HANNEL C APTIO N YES,CUSTOMIZED UP TO 12 CHANNELS
VIDEO LABEL YES
PRO GRAM TIMER YES
SLEEP 30,60,90 MINUTES
JUMP YES
SA-VA CO NTROL YES
XDS YES
C HANNEL BLOC K YES
PRO GRAM PALETTEMO VIE, SPORTS, STANDAR D
COLOR TEMP. TRINITO NE ADJ (HIGH/MEDIUM/NTSC STANDAR D)
BRIGHTVIEW DUAL CO MPO NENT SCR EEN
GAMMA COMPENSATYES
VIEWING ANGLE 130/55
VIDEO AMPLIFIERWIDEBAND
C HANNEL MAGIC 8 FAVORITE CHANNELS
CO NV ADJUSTMENTWITH R EMOTE




Mode l KP53S65: Spec ifications

C HANNEL COVER          181 CABLE COMPATIBLE
TUNING SYSTEM           EXPR ESS TUNING SYSTEM (181 C HANNEL)
PROJECTIO N LENS        MICROFOCUS LENS SYSTEM
PICTUR E BR IGHT        460 FT LAMBERTS
INPUT                   2 R F INPUTS
INPUTS                  FRO NT AUDIO/VIDEO INPUTS WITH S-VIDEO
ANT INPUT               R F 75 O HM
OUTPUTS                 VARIABLE/FIXED AUDIO OUTPUT
OUTPUTS                 MO NITOR OUTPUT AND CO NTROL S OUTPUT
AUDIO /VID INPUT        1 A/V WITH S-VIDEO , 1 A/V O NLY
AUD/VID OUTPUT          MO NITOR OUT, AUDIO FIXED/VARIABLE
PWR R EQUIR EMENT       120 V, 60 HZ
PWR CO NSUMPTIO N       165 WATTS MAX/2.5 WATTS STANDBY
W EIGHT                 153 LBS APPRO X.
DIMENSIO NS             48" X 55 5/8 X 24 1/4 (W ,H,D)
C ABINET                 GR AY
R EMOTE CO NTRO L        RM-Y136A
COMB FILTER              3 LINE DIGITAL COMB FILTER CIRC UITRY
VIDEO PROC ESSOR         ADVANC ED VIDEO PROC ESSOR
AUDIO POW ER             12 W ATTS X 2
ENER GY STAR             COMPLIANT
S VIDEO                  FRO NT/R EAR S VIDEO INPUTS




Mode l KP61S65: Features

PEDISTAL C LAMP YES
AUTO WHITE BAL YES
BRIGHTNESS 380 FT LAMBER TS
COLOR FILTER DUAL CO LOR FILTER SYSTEM R ED & GR EEN
DYNAMIC FOCUS YES
DYNAMIC CRT DYNAMIC PICTUR E PROC ESSOR
SHADING CIRC YES
VELOCITY MO D YES
PROTEC T SCR EEN SC N61X2 (OPTIO NAL)
MTS YES
MATR IX SURROUND YES
AUDIO POW ER 12 W ATTS X 2
SPEAKER O N/OFF YES
PIP YES
PIP FR EEZE FR EEZE MEMO
C HANNEL INDEX 12 C HANNELS
MULTI-LANGUAGE ENGLISH,SPANISH,FR ENCH
FAVORITE C HANEL 5 CHANNEL
C APTIO N VISIO N YES
C HANNEL C APTIO N YES
VIDEO LABEL YES
PRO GRAM TIMER YES
SLEEP 30,60,90 MINUTES
JUMP YES
SA-VA CO NTROL YES
XDS YES
C HANNEL BLOC K YES
PRO GRAM PALETTEMO VIE, SPORTS, STANDAR D
COLOR TEMP. TRINITO NE ADJ (HIGH/MEDIUM/NTSC STANDAR D)
BRIGHTVIEW DUAL CO MPO NENT SCR EEN
GAMMA COMPENSATYES
VIEWING ANGLE 130/55
VIDEO AMPLIFIERWIDEBAND
C HANNEL MAGIC 8 FAVORITE CHANNELS
CO NV ADJUSTMENTWITH R EMOTE
Mode l KP61S65: Spec ifications

C HANNEL COVER      181 CHANNEL C ATV
TUNING SYSTEM       EXPR ESS TUNING SYSTEM ( 181 CHANNEL )
PROJECTIO N LENS    MICROFOCUS LENS SYSTEM
PICTUR E BR IGHT    380 FT LAMBERTS
INPUT               2 R F INPUTS
INPUTS              1 FRO NT/R EAR A/V WITH S-VIDEO, 1 R EAR A/V
ANT INPUT           75 O MHS
OUTPUTS             VARIABLE/FIXED AUDIO OUTPUT
OUTPUTS             MO NITOR OUT
AUDIO /VID INPUT    2 R EAR AND 1 FRO NT AUDIO/VIDEO
SPEAKER             12W X 2
PWR R EQUIR EMENT   120 V, 60 HZ
PWR CO NSUMPTIO N   165 WATTS MAX/2.5 WATTS STANDBY
W EIGHT             269 LBS
DIMENSIO NS         52 3/4 X 59 3/8 X 25 3/8 (W ,H,D)
C ABINET            DARK GR AY FINISH
R EMOTE CO NTRO L   RM-Y136
COMB FILTER         3 LINE COMB FILTER CIRC UITRY
VIDEO PROC ESSOR    ADVANC ED VIDEO PROC ESSOR
ENER GY STAR        YES
S VIDEO             R EAR S VIDEO INPUT, FRO NT S-VIDEO INPUT
S O UTPUT           CO NTROL S OUTPUT

				
DOCUMENT INFO
Shared By:
Categories:
Stats:
views:347
posted:11/15/2010
language:English
pages:32
Description: Sony Kp53V25 Projection Tv document sample