Docstoc

Sony Projection Tv Power Supply Sony KP41T65

Document Sample
Sony Projection Tv Power Supply Sony KP41T65 Powered By Docstoc
					Sony KP41T65         Chassis RA2A

Looks like AGC overload on live video. Test patterns OK.

C5145 10uf50v located on the PT board

Wayne Vanaman
Omega Electronics
6904 W Fairfield Dr
Pensacola, Fl. 32506-3310



Sony PTV is a 1998 model KP41T65.
The set will not turn on until about the 3rd, or 4th try.
When the picture comes in, it is in from both sides about 2 inches, and
Down from the top, and up from the bottom about 2 inches. After about 5 minutes,
the picture finally fills the screen, but it looks a little milky, or some
what out of focus. They say if it is left on too long, it will shut
off

A can of circuit coolant lead me straight to C655 (2200 ufd. @ 25VDC), on
power supply module. Read about 1650 ufd. when cold, and about 1850 ufd.
after heated up.
LeRoy Westlund




         KP41T65

         Subject
         ANODE AND HV LEAD P/N




       SYMPTOMS

       What are the part numbers for the anode and focus leads?

       RESOLUTION

       Anode 1-779-095-21
       Focus Lead 1-900-231-42
  KP41T65

  Subject
  NO AUDIO, IC403


SYMPTOMS

No audio,

RESOLUTION

IC403 defective. Replaced IC403 or the A Board. Your assistance is need
to obtain the necessary information to find the solution to this failure..
Please contact your Tech Rep. with the information required below.

The Vcc of audio amp may be higher than expected.
Vcc is provided from PIT but no regulator in this line so the voltage varies
by a variation of PIT winding. To verify that we want to know the voltage of
Vcc.
Please measure the voltage between pin 9(Vcc) and pin 3(GND) of IC404.
It's supposed to be around 30V. If our assumption is correct then
additional diode in Vcc line will help an IC404 failure. Design will
determine type of diode and the location of the insertion.



  KP41T65, KP46C65

  Subject
  P/N FOR IC5052 INCORRECT, 875953389


SYMPTOMS

P/N for IC-5052 in the S/M 8-759-487-47 comes up no longer available in
the system.

RESOLUTION

The correct P/N is 8-759-533-89.



  KP53S15, KP53S25, KP53S55, KP53S65, KP53V15, KP53V16, KP53V25, KP53V35,
  KP53V45, KP53V75, KP53V90, KP53XBR200, KP53XBR35, KP53XBR45,
  KP53XBR4CT
  Subject
  L and F Screens Sub


SYMPTOMS

The L Screen is No Longer Available. Is there a sub?

RESOLUTION

Both the L screen and F Screen must be replaced with the part numbers
below.

Failure to replace both screens will cause picture degrading.

Change screens to Part Numbers:

L Screen 4-070-525-01
F Screen 4-084-702-02




  KV27FV300, KV32FV300, KV36FV300

  Subject
  Picture blinked no luminance


SYMPTOMS

Picture blinked on and off but no luminance.

CAUSE

Problem look like unit had bad connection on the BC board check pin 7 of
CN306 (Y signal) good, but CN306/pin 12 no luminance out. Checked
CN306/pin 16, 14v missing !

14v come from GK board CN605 pin1 . 14v missing found PS601open
replace fixed .
Service manual is wrong Cn 605 pin 1 on the GK board show 5v it
incorrect should be 14v and pin 2 should be 5v

RESOLUTION
      Found PS601open replace fixed .

      Service manual is wrong CN605/pin 1 on the GK board show 5v it's
      incorrect.
      Should be 14v and CN605/pin 2 should be 5v

Part Number            Reference Number                  Description
157633721              PS601                             Link IC




         KP41T65

         Subject
         AUX PICTURE SNOWY, IC001


      SYMPTOMS

      Aux picture is snowy.

      RESOLUTION

      Found IC001 on the A Board defective.

Part Number             Reference Number               Description
8-752-894-96            IC001                          CXP85856A-




         KP41T65

         Subject
         DEAD, Q502


      SYMPTOMS

      Dead.

      RESOLUTION

      Replaced Q502 on the G Board.
Part Number                  Reference Number                  Description
8-729-024-05                 Q502                              2SD2348




         KP41T65

         Subject
         DEAD, T504


      SYMPTOMS

      Dead.

      RESOLUTION

      Found T504 defective on the G Board.

Part Number                  Reference Number                  Description
1-453-238-11                 T504                              FBT




         KP41T65

         Subject
         DEAD, T605


      SYMPTOMS

      Primary input okay, extremely low secondary outputs.

      RESOLUTION

      Found the secondary windings T605/pin 9-12 shorted to windings
      T605/pin 13-14.
      Replaced T-605

Part Number           Reference Number           Description
142998511             T605                       CONVERTER (PIT)
         KP41T65

         Subject
         PICTURE JUMPING, IC808


      SYMPTOMS

      Picture jumping.

      RESOLUTION

      Replaced IC808 on the G Board.

Part Number              Reference Number                   Description
8-759-464-79             IC808                              PM0011AS




         KP41T65

         Subject
         SHUTS DOWN, IC601, R608


      SYMPTOMS

      Unit shuts down.

      RESOLUTION

      Found IC601 & R608 defective on the G Board.

Part Number          Reference Number         Description
8-729-041-12         IC601                    0.1 OHM FUSE 1/2W
1-202-933-61         R608                     0.1 OHM FUSE 1/2W
         KP41T65

         Subject
         SHUTS DOWN, R586


      SYMPTOMS

      Unit shuts down.

      RESOLUTION

      Found R586 on the G Board defective.

Part Number               Reference Number                  Description
1-260-292-11              R586                              1 OHM 1/2W




         KP41T15, KP41T25, KP41T35, KP41T65, KP43T70, KP46C36, KP46C65, KP46C70,
         KP46S15, KP46S17, KP46S25, KP46V25, KP46V35, KP48S35, KP48S65, KP48S72,
         KP48V45, KP48V75, KP53S15, KP53S17, KP53S25, KP53S35, KP53S65, KP53V25,
         KP53V35, KP53V45, KP53V75, KP53XBR45, KP61S35, KP61S65, KP61V25,
         KP61V35, KP61V45, KP61V75, KP61XBR48

         Subject
         UP DATE OF THE NVM JIG I/M, GEN SB31


      SYMPTOMS

      If the need should arise that a circuit board needs to be replaced, It might
      contain an EEPROM. If the EEPROM data is not written into the EEPROM
      of the replacement board all the service or customer adjustments will be
      lost. Example: Convergence adjustments. This will then require additional
      time to re-converge a projection TV.



      RESOLUTION

      Refer to SB GENTVP E08921219 for NVM Jig connections. Also refer to
      the NVM Instruction Manual for operating instructions E16415167 or TV
      SB449. The I/M will not address all chassis since it was written prior to
      RA-6 and DA4 chassis. The SB E08921219 contains the settings for all
      chassis.
  KP41T65

  Subject
  Two types of CRTs Used


SYMPTOMS

Two types of CRTs Used

RESOLUTION

If you need to replace the CRT please refer to the chart below for the
correct CRT needed.
CRT Serial Number Range 9000001-9018822
Red 8-733-539-05
Blue 8-733-519-05
Green 8-733-537-05

Serial Number Range 9500001-9534348
Red A-1501-367-A
Blue A-1501-369-A
Green A-1501-372-A
NOTE: Due to the CRT change some boards were also changed. Please
see the
attached SB below before ordering any boards.

SUPPORTING DOCUMENTS AND GRAPHICS



                                                      Name: SB400R1.pdf
                                                      Description: SB400R1




  KP41T65

  Subject
  Unit in shutdown


SYMPTOMS
      Unit is dead.

      CAUSE

      No HV, TV just clicks. Found B+ voltage 135v. Source reading 10v and
      diode D655 getting hot. Disconnect 220v source to CB PCB and HV
      restored.
      Found shorted video IC761. Replaced and solved problem.



      RESOLUTION

      No HV, TV just clicks. Found B+ voltage 135v. Source reading 10v and
      diode D655 getting hot. Disconnect 220v source to CB PCB and HV
      restored.
      Found shorted video IC761. Replaced and solved problem.


Part Number                Reference Number                  Description
875943439                  314                               CB Board




         KP41T65, KP46C65, KP48S65, KP48S65R, KP48V45, KP48V75, KP48V75, KP53S65,
         KP53V45, KP53V75, KP53V75, KP61S35, KP61S65, KP61V45, KP61V75, KP61V75

         Subject
         Repeat failures of the audio amplifier


      SYMPTOMS

      We are having a continuing problem with the RA-2 chassis models. We
      get a no audio situation and find the Audio Amp TA8216H (IC404) shorted
      and PS401 open. We replace both components and the unit works fine for
      anywhere from 3 to 6 months.


      RESOLUTION

      You assistance is need to obtain the necessary information to find the
      solution to this failure.. Please contact your Tech Rep with the information
      required below.
      The Vcc of audio amp may be higher than expected.
      Vcc is provided from PIT but no regulator in this line so the voltage varies
      by a variation of PIT winding. To verify that we want to know the voltage of
      Vcc.
      Please measure the voltage between pin 9(Vcc) and pin 3(GND) of IC404.
      It's supposed to be around 30V. If our assumption is correct then
      additional diode in Vcc line will help an IC404 failure. Design will
      determine type of diode and the location of the insertion with the
      information supplied from the servicers.


Part Number            Reference Number            Description
8-759-168-24           IC404                       Audio Amp TA8216H
1-532-984-11           PS401                       IC 2A/90V




         KP41T65, KP46C65, KP48S65, KP48V75, KP53S65, KP53V75, KP61S65, KP61V75

         Subject
         Repeat failures of the audio amplifier


      SYMPTOMS

      We are having a continuing problem with the RA-2A chassis models. We
      get a no audio situation and find the Audio Amp TA8216H (IC404) shorted
      and PS401 open. We replace both components and the unit works fine for
      anywhere from 3 to 6 months.


      RESOLUTION

      Your assistance is needed to obtain the necessary information to find the
      solution to this failure. Please contact your Tech Rep with the information
      required below.

      The Vcc of audio amp may be higher than expected.
      Vcc is provided from PIT but no regulator in this line so the voltage varies
      by a variation of PIT winding. To verify that we want to know the voltage of
      Vcc.
      Please measure the voltage between IC404/pin 9 (Vcc) and pin 3 (GND)
      of IC404 or IC403 Audio Amp . It's supposed to be around 30V. If our
      assumption is correct then additional diode in Vcc line will help an IC404
      failure. Design will determine type of diode and the location of the insertion
      with the information supplied from the servicers.

      NOTE: Since we never received the requested information from the field
      no diode or circuit mod was created for this continuing failure. The
      information requested would have giving the engineering the details they
      needed to confirm there opinion that the voltage might be too high but
      with no feedback they could not tell if their guess was correct or not.


Part Number           Reference Number             Description
8-759-168-24          IC404                        Audio Amp TA8216H
1-532-984-11          PS401                        IC 2A/90V




         KP41T15, KP41T25, KP41T35, KP41T65, KP43HT20, KP43T70, KP43T75, KP43T90,
         KP46C36, KP46C65, KP46C70, KP46S15, KP46S25, KP46V25, KP46V35, KP48S35,
         KP48S65, KP48S65R, KP48S70, KP48S72, KP48S72, KP48S75, KP48V45, KP48V75,
         KP48V80, KP48V85, KP48V90, KP51HW40, KP53HS20, KP53HS30, KP53N74,
         KP53S15, KP53S25, KP53S35, KP53S65, KP53S70, KP53S75, KP53V25, KP53V35,
         KP53V45, KP53V75, KP53V80, KP53V85, KP53V90, KP53XBR45, KP53XBR4CT,
         KP57HW40, KP57XBR10W, KP61HS20, KP61HS30, KP61S65, KP61S70, KP61S75,
         KP61V25, KP61V35, KP61V45, KP61V75, KP61V80, KP61V85, KP61V90,
         KP61XBR48, KP65XBR10W

         Subject
         Focus Block Part Change


      SYMPTOMS

      The original Focus Block is no longer available.

      RESOLUTION

      If the Focus Block should need to be replaced the new sub P/N 1-223-
      925-31 should be used. The wire connections will be difference. See the
      diagram below for proper wiring.

      Description Former P/N New P/N
      Focus Block 1-223-925-11 1-223-925-31
      Focus Block 1-223-925-12 1-223-925-31
      Focus Block 1-223-925-81 1-223-925-31
      The -51 should sub to the -61 and has 11 connections. They should not
      sub to the -31 or -71 which have 10 connections. The -31 and -71 differ in
      the value of the resistors and should not sub as long as both are available.


      SUPPORTING DOCUMENTS AND GRAPHICS



                                                  Name: sb555.pdf
                                                  Description: Focus Block diagram
                                                  Size: 16226 bytes




         KP41T65, KP46C65, KP48S65, KP48V75, KP53S65, KP53V75, KP61S65, KP61V75

         Subject
         Excessive red on picture


      SYMPTOMS

      Excessive red on picture

      CAUSE

      Red drive too high. Red G2 voltage cannot be adjusted properly. Running
      red G2 through its normal range causes red to jump from blanked to
      retrace.

      RESOLUTION

      Replaced C315 red S/H cap. Cap measured OK with capacitor checker,
      but substituting C315 resolved the problem. Cap was causing excessive
      red drive.

      Located at IC301/pin 19.

Part Number            Reference Number                 Description
113049500              C315                             0.1UF 50V Film
  KP41T65

  Subject
  CRT and board P/N change


SYMPTOMS

CRT and board P/N change

RESOLUTION

Please see the attached Supplement.

SUPPORTING DOCUMENTS AND GRAPHICS



                                                 Name: Suppleme.pdf
                                                 Description: Supplement1




  KP41T65, KP46C65, KP48S65, KP53S65, KP61S65

  Subject
  PN for C514 100pf and 680pf at 2kv


SYMPTOMS

The part number for C514 is not provided in the G board parts listing,
because it is one of those selected values, per HV adjustment procedures
on page 45. The values may be 100, 390, or 680 pf at 2KV. Need the P/N
for the 100PF and the 680PF at 2kv.



RESOLUTION

The P/N are:
680pf /2kv 1-162-116-00
100pF/2kv 1-107-444-11 ceramic disc cap
  KP46C65

  Subject
  CONTROL DOOR P/N CHANGE, X-403-445-62


SYMPTOMS

P/N 4-057-605-01, control door subs to NLA.

RESOLUTION

Order the control panel assy per the following X-403-445-62




  KP46C65

  Subject
  PART NUMBER ANODE & FOCUS LEAD


SYMPTOMS

What are the part numbers for the anode and focus leads?

RESOLUTION

Anode 1-779-095-21
Focus Lead 1-900-231-42




  KP46C65

  Subject
  DEAD, R610


SYMPTOMS

Dead.

RESOLUTION

Found R610 open on the G Board.
Part Number                  Reference Number                   Description
1-247-887-00                 R610                               220K 1/4W




         KP46C65

         Subject
         DEAD, R614


      SYMPTOMS

      Dead.

      RESOLUTION

      Found R614 on the G Board was defective.

Part Number           Reference Number            Description
1-247-887-00          R614                        220K 1/4W RESISTOR




         KP48S65, KP61S65

         Subject
         P/N FOR IC5052 INCORRECT, 8-759-533-89


      SYMPTOMS

      P/N for IC-5052 in the S/M 8-759-487-47 comes up no longer available in
      the system.

      RESOLUTION

      The correct P/N is 8-759-533-89.

Part Number             Reference Number                Description
8-759-533-89            IC5052                          SDA9288X-B121
         KP48S65

         Subject
         DEAD, IC601, R608, D662


      SYMPTOMS

      Dead.

      RESOLUTION

      Found IC601, R608, and D662 defective on the G Board.

Part Number         Reference Number       Description
8-719-991-33        D662                   ISS133T-77
8-729-041-12        IC601                  MX0841AB-F
1-202-933-61        R608                   FUSE 0.1 OHM 1/2W RESISTOR




         KP48S65

         Subject
         NO PICTURE, T504


      SYMPTOMS

      No Picture.

      RESOLUTION

      Found T504 defective on the G: Board.

Part Number                 Reference Number                Description
1-453-238-11                T504                            FBT
         KP48S35, KP48S35, KP48S35, KP48S65

         Subject
         NO VERTICAL, PS601 & PS602


      SYMPTOMS

      No vertical.

      RESOLUTION

      Found PS601 & PS602 open on the G Board.

Part Number               Reference Number            Description
1-533-597-21              PS601                       LINK IC
1-533-597-21              PS602                       LONK IC




         KP48S65

         Subject
         POOR CONVERGENCE, IC803.


      SYMPTOMS

      Poor convergence.

      RESOLUTION

      Replaced IC803 on the G Board.

Part Number             Reference Number         Description
8-759-183-37            IC1803                   Shading Amp.




         KP53S65
         Subject
         POOR PICTURE, MIRROR BROKEN


      SYMPTOMS

      Poor picture.

      RESOLUTION

      Broken mirror.

Part Number                 Reference Number                Description
4-048-181-01                80                              MIRROR




         KP53S65

         Subject
         P/N FOR IC5052 INCORRECT, 8-759-533-89.


      SYMPTOMS

      P/N for IC-5052 in the S/M 8-759-487-47 comes up no longer available in
      the system.

      RESOLUTION

      The correct P/N is 8-759-533-89.




         KP53S65, KP53V75

         Subject
         DAMAGED PIX TUBES


      SYMPTOMS

      A dab of what appears to be a clear silicon compound is applied to the
      junction of the CRT pins and sockets, to prevent the C boards from getting
      loose, it seems like the new models are receiving an excessive application
      of this compound making it very difficult to remove the C boards for
      service. When tech use a blade to cut exposed portion, enough of this
      compound has penetrated in front of the socket, preventing a gentle
      separation from the tube causing the frequent rupture of the CRT tip.
      HQ: Pittsburgh will reduce this compound to prevent this damage.

      SYMPTOMS

      CRT Board very hard to remove causing damage to the CRT.

      RESOLUTION

      We continue to investigate this issue




         KP53S65

         Subject
         DARK OR NO PICTURE, R586


      SYMPTOMS

      Dark or no picture. -Found R586 on the G Board defective. Located off
      FBT/pin4 (200V)

      RESOLUTION

      We continue to investigate this issue

Part Number              Reference Number                  Description
1-206-292-11             R586                              1 OHM 1W




         KP53S65

         Subject
         DEAD, T504 & Q502


      SYMPTOMS
      Dead.

      RESOLUTION

      FBT (T504) and Q502 defective on the A Board.

Part Number                  Reference Number                 Description
8-729-024-05                 Q502                             2SD2348
1-453-238-11                 T504                             FBT




         KP53S65

         Subject
         DEAD, T603


      SYMPTOMS

      Dead.

      RESOLUTION

      Replaced defective T603 on the G Board.

Part Number           Reference Number          Description
1-423-665-11          T603                      POWER TRANSFORMER




         KP53S65

         Subject
         IK BLANKING STANDBY LED FLASHING, D763


      SYMPTOMS

      While in Ik blanking the screen would intermittently flash on and off with a
      bright cyan raster about every 15 seconds, or it might just stay blank. All
      three Ik pulses looked normal. Sound was normal.
      RESOLUTION

      All three Ik pulses looked normal. Sound was normal.

      Replace D763 10v 1/2 watt zener located off of IC761/pin 5 on the Blue
      CRT drive board. For testing purposes, lift one end of diode to see if
      restores operation. Our diode tested good with an ohm meter. This same
      diode is used on red & green CRT boards, D708 and D733. Lifting one
      end of D763 doesn't correct problem, you can try this same test for D708
      and D733.

Part Number               Reference Number                Description
871911017                 D763                            RD1OESB2




         KP53S65

         Subject
         INTERMITTENT CONVERGENCE, IC007


      SYMPTOMS

      Intermittent Convergence.

      RESOLUTION

      Replaced IC007 on the A Board.

Part Number                 Reference Number                 Description
8-759-518-23                IC007                            EEPROM




         KP53S65

         Subject
         POOR PIN, D528


      SYMPTOMS
      Poor pincushion.

      RESOLUTION

      Found D528 located on IC501/pin1 defective on the G Board.

Part Number              Reference Number            Description
8-719-923-86             D528                        MTZJ-T-77-15




         KP53S65

         Subject
         SHUTS DOWN, X5051


      SYMPTOMS

      Unit shuts down.

      RESOLUTION

      Replaced X5051 on the PT Board.

Part Number               Reference Number               Description
1-760-095-21              X5051                          CRYSTAL




         KP53S65

         Subject
         SNOWY PICTURE, TUNER


      SYMPTOMS

      Snowy picture.

      RESOLUTION

      Replaced the tuner on the A Board.
Part Number                Reference Number                Description
8-598-340-00               TU1101                          TUNER




         KP53S65

         Subject
         VERTICAL POSITION INCORRECT, C337


      SYMPTOMS

      Vertical position incorrect.

      RESOLUTION

      Found C337 on the A Board defective.

Part Number                Reference Number                Description
1-126-960-11               C337                            1UF 50V




         KP53S65

         Subject
         blue off center


      SYMPTOMS

      Blue was off center by two inches and centering could not be adjusted.

      CAUSE

      IC804 on the G board was defective.


      RESOLUTION

      IC804 on the G board was defective.
Part Number             Reference Number                    Description
875946479               IC804                               B CONV.




         KP61S65

         Subject
         INTERMITTENT SHUTDOWN, CN8007


      SYMPTOMS

      Intermittent shutdown.

      RESOLUTION

      Found cold solder joint on CN8007. Resoldered CN8007 on the D Board.




         KP61S65

         Subject
         MIRROR P/N INCORRECT, 4-058-643-01


      SYMPTOMS

      The part number for the mirror, Ref 111, listed on page 91 of the Service
      Manual is incorrect.

      RESOLUTION

      The correct part number is 4-058-643-01.




         KP61S65

         Subject
         SCREEN ACCESSORY
SYMPTOMS

Which model do the SCN-61X2 Fit?

RESOLUTION

This is for the KP-61S65.




  KP61HS10, KP61S35, KP61S65, KP61S70, KP61S75, KP61V15, KP61V25, KP61V35,
  KP61V45, KP61V80, KP61V85, KP61XBR200, KP61XBR300, KP61XBR38

  Subject
  Screen No Longer Available


SYMPTOMS

Screens No Longer Available
(L) 4-040-124-11
(F) 4-040-123-11

(L) 4-070-283-11
(F) 4-066-082-01

RESOLUTION

If one of the screens is No Longer Available then it is recommended to
replace both Fresnel and Lenticular with the P/Ns below to achieve
satisfactory result.

Fresnel 4-084-704-01
Lenticular 4-070-283-01




     Model KP41T65: Features

      PEDISTAL CLAMP YES
      AUTO WHITE BAL YES
      BRIGHTNESS 720 FT LAMBERTS
      COLOR FILTER DUAL COLOR FILTER SYSTEM RED & GREEN
      DYNAMIC FOCUS YES
      DYNAMIC CRT DYNAMIC PICTURE PROCESSOR
SHADING CIRC YES
VELOCITY MOD YES
PROTECT SCREEN BUILT-IN HIGH CONTRAST PROTECTIVE SCREEN
MTS YES
MATRIX SURROUND YES
AUDIO POWER 12 WATTS X 2
SPEAKER ON/OFF YES
PIP YES
PIP FREEZE FREEZE MEMO
CHANNEL INDEX 12 CHANNELS
MULTI-LANGUAGE ENGLISH,SPANISH,FRENCH
FAVORITE CHANEL 5 CHANNEL
CAPTION VISION YES
CHANNEL CAPTION YES
VIDEO LABEL YES
PROGRAM TIMER YES
SLEEP 30,60,90 MINUTES
JUMP YES
SA-VA CONTROL YES
XDS EXTENDED DATA SERVICE
CHANNEL BLOCK YES
PROGRAM PALETTESTANDARD,MOVIE,SPORTS
COLOR TEMP. TRINITONE COLOR TEMPERATURE ADJUSTMENT
BRIGHTVIEW DUAL COMPONENT SCREEN
GAMMA COMPENSATYES
VIEWING ANGLE 130/55
VIDEO AMPLIFIERWIDEBAND
CHANNEL MAGIC 8 CHANNELS
CONV ADJUSTMENTWITH REMOTE




Model KP41T65: Specifications

CHANNEL COVER        181 CHANNEL
TUNING SYSTEM        EXPRESS TUNING SYSTEM ( 181 CHANNEL )
PROJECTION LENS      MICROFOCUS LENS SYSTEM
INPUT                2 REAR AUDIO/VIDEO INPUTS, 1 S-VIDEO
INPUTS               FRONT AUDIO/VIDEO INPUTS WITH S-VIDEO
ANT INPUT            75 OHMS
OUTPUTS              VARIABLE/FIXED AUDIO OUTPUTS
OUTPUTS              MONITOR
WEIGHT               122 LBS
DIMENSIONS           37 1/2 X 40 1/4 X 23 3/4 (W,H,D)
REMOTE CONTROL       RM-Y136A
COMB FILTER          3 LINE DIGITAL COMB FILTER
VIDEO PROCESSOR      BI-POLAR VIDEO PROCESSOR
AUDIO POWER          24 WATT AUDIO POWER
ENERGY STAR          ENERGY STAR COMPLIANT
S VIDEO              REAR S VIDEO INPUT
S OUTPUT             NO
Model KP46C65: Specifications

CHANNEL COVER      VHF: 2-13, UHF: 14-69, CATV 1-125
PROJ SYSTEM        3 PICTURE TUBES, 3 LENSES
PROJECTION LENS    HIGH PERFORMANCE, LARGE DIA HYBRID LENS F 1.1
PICTURE BRIGHT     7" HI-BRIGHTNESS MONOCHROME TUBES
OPTIM VIEW AREA    HORIZ: 6 FT., VERT: 6 FT 20 DEGREES L/R
INPUT              A/V W S-VIDEO, VIDEO/AUDIO 2, A/V W/S-VIDEO
ANT INPUT          75 OHM
OUTPUTS            AUDIO OUT PHONO JACKS, IMPEDANCE: 5KILOHMS
OUTPUTS            MONITOR OUT: VIDEO/AUDIO
SPEAKER            FULL RANGE 100 MM (3.9 IN) DIA
PWR REQUIREMENT    120V, 60 HZ
PWR CONSUMPTION    165 WATTS, STANDBY MODE: 3 WATTS
WEIGHT             143 LBS 5 0Z (65 KG)
DIMENSIONS         42 X 51 1/2 X 22 1/4" (1066 X 1306 X 563MM)
REMOTE CONTROL     RMY136A
AUDIO POWER        SPEAKER OUTPUT: 15 W X 2
ENERGY STAR        COMPATIBLE
S VIDEO            YES




Model KP48S65: Features

PEDISTAL CLAMP YES
AUTO WHITE BAL YES
BRIGHTNESS 550 FT LAMBERTS
COLOR FILTER DUAL COLOR FILTER SYSTEM RED & GREEN
DYNAMIC FOCUS YES
DYNAMIC CRT DYNAMIC PICTURE PROCESSOR
SHADING CIRC YES
VELOCITY MOD YES
PROTECT SCREEN SCN48X2 ( OPTIONAL )
MTS YES
MATRIX SURROUND YES
AUDIO POWER 12 WATTS X 2
SPEAKER ON/OFF YES
PIP YES
PIP FREEZE SNAP SHOT SCREEN FREEZE
CHANNEL INDEX 12 CHANNELS
MULTI-LANGUAGE ENGLISH,SPANISH,FRENCH
FAVORITE CHANEL 5 CHANNEL
CAPTION VISION YES
CHANNEL CAPTION YES
VIDEO LABEL YES
PROGRAM TIMER YES
SLEEP 30,60,90 MINUTES
JUMP YES
SA-VA CONTROL YES
XDS YES
CHANNEL BLOCK YES
PROGRAM PALETTEPROGRAM PALLETTE (STANDARD,MOVIE,SPORTS)
COLOR TEMP. HIGH,MEDIUM,NTCS STANDARD
MIRROR FIRST SURFACE MIRROR
BRIGHTVIEW DUAL COMPONENT SCREEN
GAMMA COMPENSATYES
VIEWING ANGLE 130/55
VIDEO AMPLIFIERWIDEBAND
CHANNEL MAGIC 8 FAVORITE CHANNELS
CONV ADJUSTMENTWITH REMOTE




Model KP48S65: Specifications

CHANNEL COVER        181 CABLE COMPATIBLE
PROJECTION LENS      MICROFOCUS LENS SYSTEM
PICTURE BRIGHT       550 FT LAMBERTS
INPUT                2 REAR AUDIO/VIDEO INPUTS
INPUTS               1 FRONT AUDIO/VIDEO INPUT WITH S-VIDEO
ANT INPUT            75 OHMS
OUTPUTS              VARIABLE/FIXED AUDIO OUTPUT
OUTPUTS              MONITOR OUTPUT AND CONTROL S OUTPUT
PWR REQUIREMENT      120V, 60 HZ
PWR CONSUMPTION      165 W MAX, 2.5 STANDBY
WEIGHT               148 LBS APPROX.
DIMENSIONS           43 5/8 X 52 5/8 X 22 1/2 (W,H,D)
CABINET              GRAY
REMOTE CONTROL       RMY 136A
COMB FILTER          3 LINE COMB FILTER CIRCUITRY
VIDEO PROCESSOR      ADVANCED VIDEO PROCESSOR
AUDIO POWER          12W X 2
ENERGY STAR          COMPATIABLE
S VIDEO              FRONT AND BACK S VIDEO INPUTS




Model KP48S65R: Features

PEDISTAL CLAMP YES
AUTO WHITE BAL YES
BRIGHTNESS 550 FT LAMBERTS
COLOR FILTER DUAL COLOR FILTER SYSTEM RED & GREEN
DYNAMIC FOCUS YES
DYNAMIC CRT DYNAMIC PICTURE PROCESSOR
SHADING CIRC YES
VELOCITY MOD YES
PROTECT SCREEN SCN48X2 (INCLUDED)
MTS YES
AUDIO POWER YES
SPEAKER ON/OFF 12 WATTS X 2
PIP YES
PIP FREEZE YES
CHANNEL INDEX SNAP SHOT SCREEN FREEZE
MULTI-LANGUAGE 12 CHANNELS
FAVORITE CHANEL ENGLISH,SPANISH,FRENCH
CAPTION VISION 5 CHANNEL
CHANNEL CAPTION YES
VIDEO LABEL YES
PROGRAM TIMER YES
SLEEP YES
JUMP 30,60,90 MINUTES
SA-VA CONTROL YES
XDS YES




Model KP48S65R: Specifications

CHANNEL COVER        181 CABLE COMPATIBLE
PROJECTION LENS      MICROFOCUS LENS SYSTEM
PICTURE BRIGHT       550 FT LAMBERTS
INPUT                2 REAR AUDIO/VIDEO INPUTS, COMPONENT VIDEO
INPUTS               1 FRONT AUDIO/VIDEO INPUT WITH S-VIDEO
ANT INPUT            75 OHMS
OUTPUTS              VARIABLE/FIXED AUDIO OUTPUT
OUTPUTS              MONITOR OUTPUT AND CONTROL S OUTPUT
PWR REQUIREMENT      120V, 60 HZ
PWR CONSUMPTION      165 W MAX, 2.5 STANDBY
WEIGHT               148 LBS APPROX.
DIMENSIONS           43 5/8 X 52 5/8 X 22 1/2 (W,H,D)
CABINET              GRAY
REMOTE CONTROL       RMY 136A
COMB FILTER          3 LINE COMB FILTER CIRCUITRY
VIDEO PROCESSOR      ADVANCED VIDEO PROCESSOR
AUDIO POWER          12W X 2
ENERGY STAR          COMPATIABLE
S VIDEO              FRONT AND BACK S VIDEO INPUTS




Model KP53S65: Features

PEDISTAL CLAMP YES
AUTO WHITE BAL YES
BRIGHTNESS 460 FT LAMBERTS
COLOR FILTER DUAL COLOR FILTER SYSTEM RED & GREEN
DYNAMIC FOCUS YES
DYNAMIC CRT DYNAMIC PICTURE PROCESSOR
SHADING CIRC YES
VELOCITY MOD YES
PROTECT SCREEN SCN53X2 (OPTIONAL)
MTS YES
MATRIX SURROUND YES
AUDIO POWER 12 WATTS X 2
SPEAKER ON/OFF YES
PIP YES
PIP FREEZE FREEZE MEMO
CHANNEL INDEX NONE
MULTI-LANGUAGE ENGLISH,SPANISH,FRENCH
FAVORITE CHANEL 5 CHANNEL
CAPTION VISION YES
CHANNEL CAPTION YES,CUSTOMIZED UP TO 12 CHANNELS
VIDEO LABEL YES
PROGRAM TIMER YES
SLEEP 30,60,90 MINUTES
JUMP YES
SA-VA CONTROL YES
XDS YES
CHANNEL BLOCK YES
PROGRAM PALETTEMOVIE, SPORTS, STANDARD
COLOR TEMP. TRINITONE ADJ (HIGH/MEDIUM/NTSC STANDARD)
BRIGHTVIEW DUAL COMPONENT SCREEN
GAMMA COMPENSATYES
VIEWING ANGLE 130/55
VIDEO AMPLIFIERWIDEBAND
CHANNEL MAGIC 8 FAVORITE CHANNELS
CONV ADJUSTMENTWITH REMOTE




Model KP53S65: Specifications

CHANNEL COVER        181 CABLE COMPATIBLE
TUNING SYSTEM        EXPRESS TUNING SYSTEM (181 CHANNEL)
PROJECTION LENS      MICROFOCUS LENS SYSTEM
PICTURE BRIGHT       460 FT LAMBERTS
INPUT                2 RF INPUTS
INPUTS               FRONT AUDIO/VIDEO INPUTS WITH S-VIDEO
ANT INPUT            RF 75 OHM
OUTPUTS              VARIABLE/FIXED AUDIO OUTPUT
OUTPUTS              MONITOR OUTPUT AND CONTROL S OUTPUT
AUDIO/VID INPUT      1 A/V WITH S-VIDEO, 1 A/V ONLY
AUD/VID OUTPUT       MONITOR OUT, AUDIO FIXED/VARIABLE
PWR REQUIREMENT      120 V, 60 HZ
PWR CONSUMPTION      165 WATTS MAX/2.5 WATTS STANDBY
WEIGHT               153 LBS APPROX.
DIMENSIONS           48" X 55 5/8 X 24 1/4 (W,H,D)
CABINET               GRAY
REMOTE CONTROL        RM-Y136A
COMB FILTER           3 LINE DIGITAL COMB FILTER CIRCUITRY
VIDEO PROCESSOR       ADVANCED VIDEO PROCESSOR
AUDIO POWER           12 WATTS X 2
ENERGY STAR           COMPLIANT
S VIDEO               FRONT/REAR S VIDEO INPUTS




Model KP61S65: Features

PEDISTAL CLAMP YES
AUTO WHITE BAL YES
BRIGHTNESS 380 FT LAMBERTS
COLOR FILTER DUAL COLOR FILTER SYSTEM RED & GREEN
DYNAMIC FOCUS YES
DYNAMIC CRT DYNAMIC PICTURE PROCESSOR
SHADING CIRC YES
VELOCITY MOD YES
PROTECT SCREEN SCN61X2 (OPTIONAL)
MTS YES
MATRIX SURROUND YES
AUDIO POWER 12 WATTS X 2
SPEAKER ON/OFF YES
PIP YES
PIP FREEZE FREEZE MEMO
CHANNEL INDEX 12 CHANNELS
MULTI-LANGUAGE ENGLISH,SPANISH,FRENCH
FAVORITE CHANEL 5 CHANNEL
CAPTION VISION YES
CHANNEL CAPTION YES
VIDEO LABEL YES
PROGRAM TIMER YES
SLEEP 30,60,90 MINUTES
JUMP YES
SA-VA CONTROL YES
XDS YES
CHANNEL BLOCK YES
PROGRAM PALETTEMOVIE, SPORTS, STANDARD
COLOR TEMP. TRINITONE ADJ (HIGH/MEDIUM/NTSC STANDARD)
BRIGHTVIEW DUAL COMPONENT SCREEN
GAMMA COMPENSATYES
VIEWING ANGLE 130/55
VIDEO AMPLIFIERWIDEBAND
CHANNEL MAGIC 8 FAVORITE CHANNELS
CONV ADJUSTMENTWITH REMOTE
Model KP61S65: Specifications

CHANNEL COVER     181 CHANNEL CATV
TUNING SYSTEM     EXPRESS TUNING SYSTEM ( 181 CHANNEL )
PROJECTION LENS   MICROFOCUS LENS SYSTEM
PICTURE BRIGHT    380 FT LAMBERTS
INPUT             2 RF INPUTS
INPUTS            1 FRONT/REAR A/V WITH S-VIDEO, 1 REAR A/V
ANT INPUT         75 OMHS
OUTPUTS           VARIABLE/FIXED AUDIO OUTPUT
OUTPUTS           MONITOR OUT
AUDIO/VID INPUT   2 REAR AND 1 FRONT AUDIO/VIDEO
SPEAKER           12W X 2
PWR REQUIREMENT   120 V, 60 HZ
PWR CONSUMPTION   165 WATTS MAX/2.5 WATTS STANDBY
WEIGHT            269 LBS
DIMENSIONS        52 3/4 X 59 3/8 X 25 3/8 (W,H,D)
CABINET           DARK GRAY FINISH
REMOTE CONTROL    RM-Y136
COMB FILTER       3 LINE COMB FILTER CIRCUITRY
VIDEO PROCESSOR   ADVANCED VIDEO PROCESSOR
ENERGY STAR       YES
S VIDEO           REAR S VIDEO INPUT, FRONT S-VIDEO INPUT
S OUTPUT          CONTROL S OUTPUT

				
DOCUMENT INFO
Description: Sony Projection Tv Power Supply document sample