Documents
Resources
Learning Center
Upload
Plans & pricing Sign in
Sign Out

Calcium carbonate

VIEWS: 664 PAGES: 7

									From Wikipedia, the free encyclopedia

Calcium carbonate

Calcium carbonate
Calcium carbonate NFPA 704

0 0 0 Flash point Related compounds Other anions IUPAC name Calcium carbonate Other names Identifiers CAS number RTECS number ChemSpider ID Properties Molecular formula Molar mass Appearance Density Melting point Boiling point Solubility in water Solubility product, Ksp Solubility in dilute acids Hazards MSDS EU Index ICSC 1193 Not listed CaCO3 100.09 g/mol Fine white powder. 2.71 g/cm3 (calcite) 2.83 g/cm3 (aragonite) 825 °C (calcite) 1339 °C (aragonite) decomposes .00015 mol/L (25°C) 4.8 x 10-9 [1] soluble [471-34-1] FF9335000 9708 Limestone; calcite; aragonite; chalk; marble Related compounds Other cations Calcium bicarbonate Magnesium carbonate Strontium carbonate Barium carbonate Calcium sulfate Non-flammable

Except where noted otherwise, data are given for materials in their standard state (at 25 °C, 100 kPa) Infobox references

Calcium carbonate is a chemical compound with the chemical formula CaCO3. It is a common substance found in rock in all parts of the world, and is the main component of shells of marine organisms, snails, pearls, and eggshells. Calcium carbonate is the active ingredient in agricultural lime, and is usually the principal cause of hard water. It is commonly used medicinally as a calcium supplement or as an antacid, but high consumption can be hazardous.

Occurrence
Calcium carbonate is found naturally as the following minerals and rocks: • Aragonite • Calcite • Vaterite or (μ-CaCO3) • Chalk (Blackboard chalk is calcium sulfate, CaSO4) • Limestone • Marble • Travertine To test whether a mineral or rock contains carbonate, strong acids such as hydrochloric acid or sulfuric acid can be added to it; if the sample does contain carbonate, it will fizz and produce carbon dioxide and water. (Although sulfuric acid reacts, the reaction soon ceases

1

From Wikipedia, the free encyclopedia
because the calcium sulfate produced is rather insoluble in water and limits the reaction.) Weak acids such as acetic acid will react, albeit less vigorously. All of the rocks/minerals mentioned above will react with acid. To test for calcium, prepare a platinum or nichrome wire and dip it into some hydrochloric acid. Then dip the wire into some crushed sample to be tested. Place the wire in a bunsen burner flame; if calcium is presented in the sample a brick-red flame will be produced. If a sample gives positive results for both of the two tests above, the presence of calcium carbonate is indicated.

Calcium carbonate
Alternatively, calcium oxide is prepared by calcining crude calcium carbonate. Water is added to give calcium hydroxide, and carbon dioxide is passed through this solution to precipitate the desired calcium carbonate, referred to in the industry as precipitated calcium carbonate (PCC):[2] CaCO3 → CaO + CO2 CaO + H2O → Ca(OH)2 Ca(OH)2 + CO2 → CaCO3 + H2O

Chemical properties
Calcium carbonate shares the typical properties of other carbonates. Notably: 1. it reacts with strong acids, releasing carbon dioxide: CaCO3(s) + 2HCl(aq) → CaCl2(aq) + CO2(g) + H2O(l) 2. it releases carbon dioxide on heating (to above 840 °C in the case of CaCO3), to form calcium oxide, commonly called quicklime, with reaction enthalpy 178 kJ / mole: CaCO3 → CaO + CO2 Calcium carbonate will react with water that is saturated with carbon dioxide to form the soluble calcium bicarbonate. CaCO3 + CO2 + H2O → Ca(HCO3)2 This reaction is important in the erosion of carbonate rocks, forming caverns, and leads to hard water in many regions.

Uses
Industrial applications
The main use of calcium carbonate is in the construction industry, either as a building material in its own right (e.g. marble) or limestone aggregate for roadbuilding or as an ingredient of cement or as the starting material for the preparation of builder’s lime by burning in a kiln. Calcium carbonate is also used in the purification of iron from iron ore in a blast furnace. Calcium carbonate is calcined in situ to give calcium oxide, which forms a slag with various impurities present, and separates from the purified iron.[3] Calcium carbonate is also used in the oil industry in drilling fluids as a formation bridging and filtercake sealing agent and may also be used as a weighting material to increase the density of drilling fluids to control downhole pressures. Calcium carbonate is also one of the main sources used in growing Seacrete, or Biorock. Precipitated Calcium carbonate, pre-dispersed in slurry form, is also now widely used as filler material for latex gloves with the aim of achieving maximum saving in material and production costs.[4] Calcium carbonate is widely used as an extender in paints,[5] in particular matte emulsion paint where typically 30% by weight of the paint is either chalk or marble. Calcium carbonate is also widely used as a filler in plastics.[5] Some typical examples include around 15 to 20% loading of chalk in uPVC drain pipe, 5 to 15% loading of stearate coated chalk or marble in uPVC window profile. PVC cables can use calcium carbonate at loadings of up to 70 phr (parts per hundred parts of resin) to improve mechanical properties (tensile strength and elongation) and electrical properties (volume resistivity). Polypropylene compounds are often filled with calcium carbonate to increase rigidity, a requirement that becomes important at high use temperatures.[6] It also routinely used as a filler in thermosetting resins (Sheet and Bulk moulding compounds)[6] and has also been mixed with ABS, and other ingredients, to form some types of compression molded "clay" Poker chips.

Preparation

Mississippian marble in Big Cottonwood Canyon, Wasatch Mountains, Utah. The vast majority of calcium carbonate used in industry is extracted by mining or quarrying. Pure calcium carbonate (e.g. for food or pharmaceutical use), can be produced from a pure quarried source (usually marble).

2

From Wikipedia, the free encyclopedia
Fine ground calcium carbonate is an essential ingredient in the microporous film used in babies’ diapers and some building films as the pores are nucleated around the calcium carbonate particles during the manufacture of the film by biaxial stretching. Calcium carbonate is also used in a wide range of trade and DIY adhesives, sealants, and decorating fillers.[5] Ceramic tile adhesives typically contain 70 to 80% limestone. Decorating crack fillers contain similar levels of marble or dolomite. It is also mixed with putty in setting stained glass windows, and as a resist to prevent glass from sticking to kiln shelves when firing glazes and paints at high temperature. Calcium carbonate is known as whiting in ceramics/glazing applications,[5] where it is used as a common ingredient for many glazes in its white powdered form. When a glaze containing this material is fired in a kiln, the whiting acts as a flux material in the glaze. In North America, calcium carbonate has begun to replace kaolin in the production of glossy paper. Europe has been practicing this as alkaline papermaking or acidfree papermaking for some decades. Carbonates are available in forms: ground calcium carbonate (GCC) or precipitated calcium carbonate (PCC). The latter has a very fine and controlled particle size, on the order of 2 micrometres in diameter, useful in coatings for paper. It is used in swimming pools as a pH corrector for maintaining alkalinity "buffer" to offset the acidic properties of the disinfectant agent. It is commonly called chalk as it has been a major component of blackboard chalk. Chalk may consist of either calcium carbonate or gypsum, hydrated calcium sulfate CaSO4·2H2O. Ground calcium carbonate is further used as an abrasive (both as scouring powder and as an ingredient of household scouring creams), in particular in its calcite form, which has the relatively low hardness level of 3 on the Mohs scale of mineral hardness, and will therefore not scratch glass and most other ceramics, enamel, bronze, iron, and steel, and have a moderate effect on softer metals like aluminium and copper.

Calcium carbonate

500 milligram calcium supplements made from calcium carbonate syndrome," which has serious toxicity and can be fatal. In 1915, Bertram Sippy introduced the "Sippy regimen" of hourly ingestion of milk and cream, and the gradual addition of eggs and cooked cereal, for 10 days, combined with alkaline powders, which provided symptomatic relief for peptic ulcer disease. Over the next several decades, the Sippy regimen resulted in renal failure, alkalosis, and hypercalemia, mostly in men with peptic ulcer disease. These adverse effects were reversed when the regimen stopped, but it was fatal in some patients with protracted vomiting. Milk alkali syndrome declined in men after effective treatments for peptic ulcer disease. But during the past 15 years, it has been reported in women taking calcium supplements above the recommended range of 1200 to 1500 mg daily, for prevention and treatment of osteoporosis, and is exacerbated by dehydration. Calcium has been added to over-the-counter products, which contributes to inadvertent excessive intake. Excessive calcium intake can lead to hypercalcemia, complications of which include vomiting, abdominal pain and altered mental status.[9] A form of food additive is designated as E170.[10] It is used in some soy milk products as a source of dietary calcium; one study suggests that calcium carbonate might be as bioavailable as the calcium in cow’s milk.[11]

Health and dietary applications
Calcium carbonate is widely used medicinally as an inexpensive dietary calcium supplement or antacid.[7] It may be used as a phosphate binder for the treatment of hyperphosphatemia (primarily in patients with chronic renal failure). It is also used in the pharmaceutical industry as an inert filler for tablets and other pharmaceuticals.[8] Calcium carbonate is used in the production of toothpaste and is also used in homeopathy as one of the constitutional remedies. Excess calcium from supplements, fortified food and high-calcium diets, can cause the "milk alkali

Environmental applications
In 1989, a researcher, Ken Simmons, introduced CaCO3 into the Whetstone Brook in Massachusetts.[12] His hope was that the calcium carbonate would counter the acid in the stream from acid rain and save the trout that had ceased to spawn. Although his experiment was a success, it did increase the amounts of aluminium ions in the area of the brook that was not treated with the limestone. This shows that CaCO3 can be added to neutralize the effects of acid rain in river ecosystems. Currently calcium carbonate is used to neutralize acidic conditions in both soil and water.[13][14]. Since the 1970s, such liming has been practiced on a large scale in Sweden to

3

From Wikipedia, the free encyclopedia
mitigate acidification and several thousand lakes and streams are limed repeatedly.[15]

Calcium carbonate

Solubility
With varying CO2 pressure
Calcium ion solubility as a function of CO2 partial pressure at 25 °C (Ksp = 4.47×10−9) (atm) 10−12 10−10 10−8 10−6 10−4 3.5 × 10−4 10−3 10−2 10−1 1 10 pH 12.0 11.3 10.7 9.83 8.62 8.27 7.96 7.30 6.63 5.96 5.30 [Ca2+] (mol/L) 5.19 × 10−3 1.12 × 10−3 2.55 × 10−4 1.20 × 10−4 3.16 × 10−4 4.70 × 10−4 6.62 × 10−4 1.42 × 10−3 3.05 × 10−3 6.58 × 10−3 1.42 × 10−2

Calcination equilibrium
Equilibrium Pressure of CO2 over CaCO3[16] 550 °C 587 °C 605 °C 680 °C 727 °C 748 °C 777 °C 800 °C 830 °C 852 °C 871 °C 881 °C 891 °C 898 °C 937 °C 1082 °C 1241 °C 0.055 kPa 0.13 kPa 0.31 kPa 1.80 kPa 5.9 kPa 9.3 kPa 14 kPa 24 kPa 34 kPa 51 kPa 72 kPa 80 kPa 91 kPa 101 kPa 179 kPa 901 kPa 3961 kPa

Calcium carbonate is poorly soluble in pure water (47 mg/L at normal atmospheric CO2 partial pressure as shown below). The equilibrium of its solution is given by the equation (with dissolved calcium carbonate on the right): CaCO3 ? Ca2+ + CO32–

Ksp = 3.7×10–9 to 8.7×10–

Calcination of limestone using charcoal fires to produce quicklime has been practiced since antiquity by cultures all over the world. The temperature at which limestone yields calcium oxide is usually given as 825 °C, but stating an absolute threshold is misleading. Calcium carbonate exists in equilibrium with calcium oxide and carbon dioxide at any temperature. At each temperature there is a partial pressure of carbon dioxide that is in equilibrium with calcium carbonate. At room temperature the equilibrium overwhelmingly favors calcium carbonate, because the equilibrium CO2 pressure is only a tiny fraction of the partial CO2 pressure in air, which is about 0.035 kPa. At temperatures above 550 °C the equilibrium CO2 pressure begins to exceed the CO2 pressure in air. So above 550 °C, calcium carbonate begins to outgas CO2 into air. But in a charcoal fired kiln, the concentration of CO2 will be much higher than it is in air. Indeed if all the oxygen in the kiln is consumed in the fire, then the partial pressure of CO2 in the kiln can be as high as 20 kPa. The table shows that this equilibrium pressure is not achieved until the temperature is nearly 800 °C. For the outgassing of CO2 from calcium carbonate to happen at an economically useful rate, the equilibrium pressure must significantly exceed the ambient pressure of CO2. And for it to happen rapidly, the equilibrium pressure must exceed total atmospheric pressure of 101 kPa, which happens at 898 °C.

where the solubility product for [Ca2+][CO32–] is given as anywhere from Ksp = 3.7×10–9 to Ksp = 8.7×10–9 at 25 °C, depending upon the data source.[16][17] What the equation means is that the product of molar concentration of calcium ions (moles of dissolved Ca2+ per liter of solution) with the molar concentration of dissolved CO32– cannot exceed the value of Ksp. This seemingly simple solubility equation, however, must be taken along with the more complicated equilibrium of carbon dioxide with water (see carbonic acid). Some of the CO32– combines with H+ in the solution according to: HCO3– ? H+ + CO32–

Ka2 = 5.61×10–11 at 25 °C

HCO3– is known as the bicarbonate ion. Calcium bicarbonate is many times more soluble in water than calcium carbonate—indeed it exists only in solution. Some of the HCO3– combines with H+ in solution according to: H2CO3 ? H+ + HCO3– Ka1 = 2.5×10–4 at 25 °C

Some of the H2CO3 breaks up into water and dissolved carbon dioxide according to: H2O + CO2(dissolved) ? H2CO3 Kh = 1.70×10–3 at 25 °C

4

From Wikipedia, the free encyclopedia
And dissolved carbon dioxide is in equilibrium with atmospheric carbon dioxide according to:

Calcium carbonate

underground can be exposed to levels of CO2 much higher than atmospheric. As such water percolates through calcium carbonate 25 °C the CaCO where kH = 29.76 atm/(mol/L) at rock, (Henry 3 dissolves according constant), to the second 2 partialWhen that same water then being the CO trend. pressure. emerges from the tap, in time it comes into equilibrium with CO2 levels in the air by outgassing its excess CO2. –4 atmospheres The calcium carbonate becomes less soluble as a result For ambient air, is around 3.5×10 and the excess precipitates as lime scale. This same pro(or equivalently 35 Pa). The last equation above fixes the concentration of dissolved CO2 as a function of , cess is responsible for the formation of stalactites and stalagmites in limestone caves. independent of the concentration of dissolved CaCO3. At Two hydrated phases of calcium carbonate, monoatmospheric partial pressure of CO2, dissolved CO2 conhydrocalcite, CaCO3·H2O and ikaite, CaCO3·6H2O, may –5 moles/liter. The equation before centration is 1.2×10 precipitate from water at ambient conditions and persist that fixes the concentration of H2CO3 as a function of as metastable phases. [CO2]. For [CO2]=1.2×10–5, it results in [H2CO3]=2.0×10–8 moles per liter. When [H2CO3] is known, the remaining three equations together with H2O ? H+ + OH–

With varying pH

We K = 10–14 at 25 °C now consider the problem of the maximum solubility of calcium carbonate in normal atmospheric conditions ( = 3.5 × 10−4 atm) when the pH of the solu(which is true for all aqueous solutions), and the fact tion is adjusted. This is for example the case in a swimthat the solution must be electrically neutral, ming pool where the pH is maintained between 7 and 8 2[Ca2+] + [H+] = [HCO3–] + 2[CO32–] + [OH–] (by addition of sodium bisulfate NaHSO4 to decrease the pH or of sodium bicarbonate NaHCO3 to increase it). make it possible to solve simultaneously for the remainFrom the above equations for the solubility product, the ing five unknown concentrations (note that the above hydratation reaction and the two acid reactions, the folform of the neutrality equation is valid only if calcium lowing expression for the maximum [Ca2+] can be easily carbonate has been put in contact with pure water or deduced: with a neutral pH solution; in the case where the origin water solvent pH is not neutral, the equation is modified). The table on the right shows the result for [Ca2+] and [H+] (in the form of pH) as a function of ambient partial showing a quadratic dependence in [H+]. The numerical pressure of CO2 (Ksp = 4.47×10−9 has been taken for the application with the above values of the constants gives calculation). 1) At atmospheric levels of ambient CO2 the table indicates the solution will be slightly alkaline with a maximum CaCO3 solubility of 47 mg/L. 2) As ambient CO2 partial pressure is reduced below atmospheric levels, the solution becomes more and more alkaline. At extremely low , dissolved CO2, bicarbonate ion, and carbonate ion largely evaporate from the solution, leaving a highly alkaline solution of calcium hydroxide, which is more soluble than CaCO3. Note that for = 10−12 atm, the [Ca2+][OH-]2 product is still below the solubility product of Ca(OH)2 (8×10−6). For still lower CO2 pressure, Ca(OH)2 precipitation will occur before CaCO3 precipitation. 3) As ambient CO2 partial pressure increases to levels above atmospheric, pH drops, and much of the carbonate ion is converted to bicarbonate ion, which results in higher solubility of Ca2+. The effect of the latter is especially evident in day to day life of people who have hard water. Water in aquifers pH [Ca2+]max (10-4mol/L or °F) [Ca2+]max (mg/L) 6390 2540 1010 403 160 63.9 25.4 18.9 10.1 7.0 7.2 7.4 253 7.6 7.8 8.0 8.2 8.27 8.4 1590 635 101 40.0 15.9 6.35 4.70 2.53

Comments: • decreasing the pH from 8 to 7 increases the maximum Ca2+ concentration by a factor 100. Water with a pH maintained to 7 can dissolve up to 15.9 g/L of CaCO3. This explains the high Ca2+ concentration in some mineral waters with pH close to 7. • note that the Ca2+ concentration of the previous table is recovered for pH = 8.27 • keeping the pH to 7.4 in a swimming pool (which gives optimum HClO/ClO− ratio in the case of "chlorine" maintenance) results in a maximum Ca 2+ concentration of 1010 mg/L. This means that successive cycles of water evaporation and partial renewing may result in a very hard water before CaCO3 precipitates (water with a Ca2+ concentration

5

From Wikipedia, the free encyclopedia
above 120 mg/L or 30 °F is considered very hard). Addition of a calcium sequestring agent or complete renewing of the water will solve the problem.

Calcium carbonate
yielding in the end as many H+ ions as the strong acid to "dissolve" the calcium carbonate. • The calculation in the case of phosphoric acid (which is the most widely used for domestic applications) is more complicated since the concentrations of the four dissociation states corresponding to this acid must be calculated together with [HCO3−], [CO32−], [Ca2+], [H+] and [OH−]. The system may be reduced to a seventh degree equation for [H+] the numerical solution of which gives [A] (mol/ 1 L) Final pH 10−1 10−2 10−3 3.05 8.06 10−4 4.01 8.24 10−5 5.00 8.26 10−6 5.97 8.26 10−7 6.74 8.26

Solubility in a strong or weak acid solution
Solutions of strong (HCl) or weak (acetic, sorbic, lactic, phosphoric) acids are commercially available. They are commonly used as descaling agents to remove limescale deposits. The maximum amount of CaCO3 that can be "dissolved" by one liter of an acid solution can be calculated using the above equilibrium equations. • In the case of a strong monoacid with decreasing acid concentration [A] = [A−], we obtain (with CaCO3 molar mass = 100 g): [A] (mol/ 1 L) Final pH 10−1 10−2 10−3 3.00 8.14 10−4 4.00 8.25 10−5 5.00 8.26

1

Initial pH 1.08 1.62 2.25 6.71 7.17 7.63

7

8

Initial pH 0.00 1.00 2.00 6.75 7.25 7.75

Dissolved 62.0 7.39 0.874 0.123 0.0536 0.0477 0.0471 0.0471 0 10−6 CaCO3 (g 10−10 10−7 per liter acid) 7.00 6.00 of6.79

8.26 where [A] = [H3PO4] + [H2PO4−] + [HPO42−] + [PO43−] is the 8.26 8.27 total acid concentration. We see that phosphoric acid is Dissolved 50.0 5.00 0.514 0.0849 0.0504 0.0474 0.0471 0.0470 0.0470 more efficient than a monoacid since at the final almost CaCO3 (g neutral pH, the second dissociated state concentration per liter [HPO42−] is not negligible (see phosphoric acid). of acid) where the initial state is the acid solution with no Ca2+ (not taking into account possible CO2 dissolution) and the final state is the solution with saturated Ca2+. For strong acid concentrations, all species have a negligible concentration in the final state with respect to Ca2+ and A− so that the neutrality equation reduces approximately to 2[Ca ] = [A ] yielding . When the −] becomes non negliconcentration decreases, [HCO3 gible so that the preceding expression is no longer valid. For vanishing acid concentrations, we recover the final pH and the solubility of CaCO3 in pure water. • In the case of a weak monoacid (here we take acetic acid with pKA = 4.76) with decreasing total acid concentration [A] = [A−]+[AH], we obtain: [A] (mol/ 1 L) 10−1 10−2 10−3 3.91 10−4 4.47 10−5 5.15 10−6
2+ −

See also

Travertine calcium carbonate deposits from a hot spring 10−7 10−10 Ocean acidification 6.79 Gesso 7.00 Cuttlefish 8.26 8.27 Cuttlebone 0.0470 0.0470 Marble Industrial use of (ground) marble Limescale

• 6.02 • Final pH 6.75 7.25 7.75 8.14 8.25 8.26 8.26 • Dissolved 49.5 4.99 0.513 0.0848 0.0504 0.0474 0.0471• • CaCO3 (g • per liter of acid) Initial pH 2.38 2.88 3.39 We see that for the same total acid concentration, the initial pH of the weak acid is less acid than the one of the strong acid; however, the maximum amount of CaCO3 which can be dissolved is approximately the same. This is because in the final state, the pH is larger that the pKA, so that the weak acid is almost completely dissociated,

References
[1] [2] Pradyot Patnaik. Handbook of Inorganic Chemicals. McGraw-Hill, 2002, ISBN 0070494398 "Solvay Precipitated Calcium Carbonate: Production". Solvay S. A.. 2007-03-09. http://www.solvaypcc.com/ safety_environment/0,0,1000044-_EN,00.html. Retrieved on 2007-12-30.

6

From Wikipedia, the free encyclopedia
[3] "Blast Furnace". Science Aid. http://www.scienceaid.co.uk/chemistry/industrial/ blastfurnace.html. Retrieved on 2007-12-30. [4] "Precipitated Calcium Carbonate uses". http://www.aristocratholding.com/calris-5.html. [5] ^ "Calcium Carbonate Powder". Reade Advanced Materials. 2006-02-04. http://www.reade.com/Products/ Minerals_and_Ores/calcium_carbonate.html. Retrieved on 2007-12-30. [6] ^ "Calcium carbonate in plastic applications". Imerys Performance Minerals. http://www.imerysperfmins.com/calcium-carbonate/eu/calciumcarbonate-plastic.htm. Retrieved on 2008-08-01. [7] "Calcium Carbonate". Medline Plus. National Institutes of Health. 2005-10-01. http://www.nlm.nih.gov/ medlineplus/druginfo/medmaster/a601032.html. Retrieved on 2007-12-30. [8] Herbert A. Lieberman, Leon Lachman, Joseph B. Schwartz (1990). Pharmaceutical Dosage Forms: Tablets. pp. 153. ISBN 0824780442. [9] Clinical problem-solving, back to basics, Ilan Gabriely et al., N Engl J Med, 1 May 2008, 358(18):1952. [10] "Food-Info.net : E-numbers : E170 Calcium carbonate". http://www.food-info.net/uk/e/e170.htm. 080419 foodinfo.net [11] Y. Zhao, B. R. Martin and C. M. Weaver (2005). "Calcium Bioavailability of Calcium Carbonate Fortified Soymilk Is Equivalent to Cow’s Milk in Young Women". J. Nutr. 135 (10): 2379–2382. PMID 16177199. http://jn.nutrition.org/ cgi/content/abstract/135/10/2379.

Calcium carbonate
[12] Associated Press (1989-06-13). "Limestone Dispenser Fights Acid Rain in Stream". New York Times. http://query.nytimes.com/gst/ fullpage.html?res=950DEFD9173FF930A25755C0A96F948260. [13] R. K. Schreiber (1988). "Cooperative federal-state liming research on surface waters impacted by acidic deposition". Water, Air, & Soil Pollution 41 (1): 53–73. doi:10.1007/BF00160344 (inactive 2008-06-25). [14] Dan Kircheis; Richard Dill (2006). "Effects of low pH and high aluminum on Atlantic salmon smolts in Eastern Maine and liming project feasibility analysis" (reprinted at Downeast Salmon Federation). National Marine Fisheries Service and Maine Atlantic Salmon Commission. http://www.mainesalmonrivers.org/pages/ Liming%20Project%20Rpt.pdf. [15] M. Guhren, C. Bigler and I. Renberg (2007). "Liming placed in a long-term perspective: A paleolimnological study of 12 lakes in the Swedish liming program". Journal of Paleolimnology 37: 247–258. [16] ^ CRC Handbook of Chemistry and Physics 44th ed. [17] "Selected Solubility Products and Formation Constants at 25 °C". California State University, Dominguez Hills. http://www.csudh.edu/oliver/chemdata/data-ksp.htm.

External links
• • • • International Chemical Safety Card 1193 CID 516889 from PubChem ATC codes: A02AC01 and A12AA04 The British Calcium Carbonate Association – What is calcium carbonate

Retrieved from "http://en.wikipedia.org/wiki/Calcium_carbonate" Categories: Calcium compounds, Carbonates, Limestone, Phosphate binders, Excipients, Antacids This page was last modified on 17 May 2009, at 14:01 (UTC). All text is available under the terms of the GNU Free Documentation License. (See Copyrights for details.) Wikipedia® is a registered trademark of the Wikimedia Foundation, Inc., a U.S. registered 501(c)(3) tax-deductible nonprofit charity. Privacy policy About Wikipedia Disclaimers

7


								
To top