GA-4KXSV Pentium Prescott 1066 Motherboard

Document Sample
GA-4KXSV Pentium Prescott 1066 Motherboard Powered By Docstoc
					           GA-4KXSV
Pentium Prescott 1066 Motherboard




   USER’S MANUAL




        Pentium®Prescott Processor Motherboard
                    Rev. 1001
               12ME-4KXSVRH-1001R
          GA-4KXSV-RH Motherboard

                                                 Table of Content
English




          Item Checklist ......................................................................................... 4
          WARNING! ............................................................................................... 4
           Chapter 1 Introduction ............................................................................ 5
              Features Summary ...................................................................................... 5
              GA-4KXSV Motherboard Layout .................................................................. 7
          Chapter 2 Hardware Installation Process ............................................... 9
              2-1: Installing Processor and CPU Haet Sink ............................................. 9
                            2-1-1: Installing CPU ......................................................................................................... 9
                            2-1-2: Installing Heat Sink ............................................................................................... 10
              2- 2: Install memory modules .................................................................... 11
              2-3: Install expansion cards ...................................................................... 13
              2- 4: Connect ribbon cables, cabinet wires, and power supply................ 14
                            2-4-1 : I/O Back Panel Introduction ................................................................................ 14
                            2-4-2 : LAN LED Description .......................................................................................... 16
              2- 5: Connectors Introduction .................................................................... 17
              2- 6: Jumper Setting .................................................................................. 28
              2- 7: Block Diagram ................................................................................... 32
          Chapter 3 BIOS Setup .......................................................................... 33
                            The Main Menu ............................................................................................................... 34
                            2-1 Standard CMOS Features ........................................................................................ 36
                            2-2 Advanced BIOS Features ........................................................................................ 38
                            2-3 Integrated Peripherals ............................................................................................... 40
                            2-4 Power Management Setup ...................................................................................... 43
                            2-5 PnP/PCI Configurations ............................................................................................ 45
                            2-6 PC Health Status ....................................................................................................... 46
                            2-7 Frequency/Voltage Control ...................................................................................... 48
                            2-8 Load Fail-Safe Defaults ............................................................................................. 50
                            2-9 Load Optimized Defaults ........................................................................................... 50
                            2-10 Set Supervisor/User Password ............................................................................ 51
                            2-11Save & Exit Setup .................................................................................................... 52
                            2-12Exit Without Saving .................................................................................................. 52
          Chapter 4 INTEL RAID BIOS Configuration ........................................... 53
                                                                             2
                                                                                         Introduction

 Item Checklist
    The GA-4KXSV motherboard                              Serial ATA cable x 4
    IDE (ATA100 ) cable x 1 / Floppy cable x 1            I/O Shield Kit
    CD for motherboard driver & utility
    GA-4KXSV user’s manual




               WARNING!
Computer motherboards and expansion cards contain very delicate Integrated Circuit (IC) chips. To
protect them against damage from static electricity, you should follow some precautions whenever you
work on your computer.
   1.   Unplug your computer when working on the inside.
   2.   Use a grounded wrist strap before handling computer components. If you do not have
        one, touch both of your hands to a safely grounded object or to a metal object, such as
         the power supply case.
   3.   Hold components by the edges and try not touch the IC chips, leads or connectors, or
        other components.
   4.   Place components on a grounded antistatic pad or on the bag that came with the
        components whenever the components are separated from the system.
   5.   Ensure that the ATX power supply is switched off before you plug in or remove the ATX
                 power connector on the motherboard.


Installing the motherboard to the chassis…
     If the motherboard has mounting holes, but they don’t line up with the holes on the base and
there are no slots to attach the spacers, do not become alarmed you can still attach the spacers to
the mounting holes. Just cut the bottom portion of the spacers (the spacer may be a little hard to
cut off, so be careful of your hands). In this way you can still attach the motherboard to the base
without worrying about short circuits. Sometimes you may need to use the plastic springs to isolate
the screw from the motherboard PCB surface, because the circuit wire may be near by the hole. Be
careful, don’t let the screw contact any printed circuit write or parts on the PCB that are near the
fixing hole, otherwise it may damage the board or cause board malfunctioning.




                                                 3
          GA-4KXSV-RH Motherboard

          Chapter 1 Introduction
English




          Features Summary
          Form Factor               12” x 9.6” ATX size form factor, 6 layers PCB.
          CPU                       Supports Intel® Pentium® 4 / Pentium® D processor
                                    Intel® Prescott LGA 775 supports 533/800/1066MHz FSB
                                    L2 cache on-die per processor from 1M
          Chipset                   Intel® 945G Chipset
                                    Intel® ICH7R
                                    Intel® 6700 PXH
          Memory                    4 x DDRII socket up to 4 GB
                                    Supports Dual Channel Un-buffered DDRII 400/533/667
                                    Support 256MB, 512MB, and 1GB memory
          I/O Control               ITE IT8712F-A Super I/O
          Expansion Slots           Supports 2 PCI slots 32-Bit/33MHz (5V)
                                    Supports 2 PCI-X slots 64-Bit/133MHz
                                    Supports 1 PCI-Express x1 slot
                                    Supports 1 PCI-Express x16 slot
          SATA RAID Controller      ICH7R built in SATA RAID 0,1,5, 0+1 without Linux support
                                    Supports 4 SATAII conntectors
          IDE RAID Controller       ITE IT8212F built in IDE RAID 0,1, 0+1
          On-Board Peripherals      1 IDE connector
                                    1 Floppy port supports 2 FDD with 360K, 720K,1.2M, 1.44M
                                    and 2.88M bytes.
                                    2 PS/2 connectors
                                    1 Parallel port supports Normal/EPP/ECP mode
                                    1 Serial port (COM)
                                    4 x USB 2.0
                                    1 VGA connector
                                    1 x LAN RJ45
                                    4 x SATAII connectors
          Hardware Monitor          CPU/Power/System Fan Revolution Detect
                                    CPU shutdown when overheat
                                    System Voltage Detect




                                                 4
                                                                           Introduction

On-Board Graphic      Build in Intel® 945G Chipset


On-Board Audio        Realtek® ALC 880


On-Board LAN          Intel 82573V Gigabit Ethernet controllers


Hardware Monitor      ITE IT8712F-A controller
                      Enhanced features with CPU Vcore, DDRII 1.8V reference,
                      VCC3 (3.3V), VCC5V, +12V, +5V SB, CPU Temperature, and
                      System Temperature Values viewing by

BIOS                  AWARD BIOS on 4Mb flash RAM


Additional Features   PS/2 Mouse wake up from S1 under Windows Operating System
                      External Modem wake up
                      Supports S1, S3, S5 under Windows Operating System
                      Wake on LAN (WOL)
                      AC Recovery
                      Supports Console Redirection
                      Supports 4-pin Fan controller




                                         5
          GA-4KXSV-RH Motherboard

          GA-4KXSV Motherboard Layout
English




            1.     CPU                    21.   DDRII 3
            2.     Intel 945G             22.   DDRII 4
            3.     Intel 6700 PXH         23.   PCIEX1
            4.     Intel ICH7R            24.   PCI1(Supports 32bit/33MHz)
            5.     ITE IT8712F            25.   PCI2 (Supports 32bit/33MHz)
            6.     ITE IT8212F GigaRAID   26.   PCI-X 1 (Supports 64bit/66~133MHz)
            7.     Intel 82573V GbE       27.   PCI-X 2 (Supports 64bit/66~133MHz)
            8.     Realtek ALC 880        28.   PCIEX16
            9.     Main BIOS              29.   CD_IN
            10     Back BIOS              30.   F_Audio
            11.    IDE RAID1              31.   IR
            12.    IDE RAID2              32.   F_USB1
            13.    IDE                    33.   F_USB2
            14.    FDD                    34.   COMB
            15     SATA1                  35.   F_Panel
            16.    SATA2                  36.   CPU FAN
            17.    SATA3                  37.   NB FAN
            18.    SATA4                  38.   System FAN
            19.    DDRII 1                39.   Power FAN
            20.    DDRII 2                40.   ATX
                                          41.   ATX12V




                                            6
                                                                             Introduction

                    29            30

                              8
          10    9                          7
35
                                                         22 21 20 19   5
          23 24          25       26 27        28                           31
     14                                                                     37

           6                                                                40
                                                                       2
           32
     11

                     4
39                                                                                36
                                                                        1
     12    33       18    13
           15                          3

          16


                    17                                   38
                                                    41




                                                         7
          GA-4KXSV-RH Motherboard

           Chapter 2 Hardware Installation Process
English




          2-1: Installing Processor and CPU Haet Sink




          2-1-1: Installing CPU
          Step 1 Gently lift the metal lever located on the CPU socket to the upper-right position.
          Step 2 Remove the plastic covering on the CPU socket.
          Step 3 Align the indented corner of the CPU with the triangle and gently insert the CPU into position.
                 (Grasping the CPU firmly between your thumb and forefinger, carefully place it into the socket
                 in a straight and downwards motion. Avoid twisting or bending motions that might cause
                 damage to the CPU during installation.)
          Step 4 Once the CPU is properly inserted, please replace the plastic covering and push the metal
                 lever back into its original position.
          Step 5 Close the lever, reverse step 1 & 2.




                                                            8
                                                                              Hardware Installation Process

2-1-2: Installing Heat Sink

                                                                                       Male Push Pin



                                                                                       The top of Female Push Pin


                                                                                       Female Push Pin


Fig.1                                                 Fig. 2
Please apply heatsink paste on the surface of         ( to remove the heatsink, turning the push pin along
the installed CPU.                                    the direction of arrow; and reverse the previous
                                                      step to install the heat sink.)
                                                      Please note the direction of arrow sign on the male
                                                      push pin doesn't face inwards before installation.
                                                      (This instruction is only for Intel boxed fan)




Fig. 3                                                Fig. 4
Place the heatsink on top the CPU and make            Please make sure the Male and Female push pin
sure the push pins align to the pin hole on the       are brought together. (for detailed installation
motherboard.Push down the push pins                   instructions, please refer to the heatsink installation
diagonally.                                           section of the user manual)




Fig. 5                                                Fig. 6
Please check the back side of teh motherboard.        Attach the power connector of the heatsink to the
Make sure the push pin is seated firmly as the        CPU fan header located on the motherboard.
picture shown. Installation completed.




                                                  9
          GA-4KXSV-RH Motherboard

          2- 2: Install memory modules
English




                    Before installing the processor and heatsink, adhere to the following warning:
          When DIMM LED is ON, do not install/remove DIMM from socket.
          GA-4KXSV has 4 dual inline memory module (DIMM) socets. It supports the Dual Channel Technology.
          The BIOS will automatically detects memory type and size during system boot. For detail DIMM
          installation, please refer to the following instructions.




                                                                      Channel A




                                                                  Channel B




                                                                 10
                                                                           Hardware Installation Process
Table 1. Supported DIMM Module Type


       Technology         Organization                  SDRAM Chips/DIMM
       256MB              8MB x 8 x 4 bks                     8
                          16MB x 4 x 4bks                     16
       512MB              16MB x 8 x 4bks                     8
                          32MB x 4 x 4bks                     16
       1GB                32MB x 8 x 4bks                     8
                          64MB x 4 x 4bks                     16

Table 2. DIMM Placement DDR2-533/667

          DIMM Configuration                    DIMM1             DIMM2

          1   Single Rank                       Empty             Empty
          1   Dual Rank                         Empty             Empty
          2   Single Rank                       Empty             Single Rank
          1   Dual Rank, 1 Single Rank          Empty             Single Rank
          2   Dual Rank                         Empty             Dual Rank


Installation Steps:
1. Unlock a DIMM socket by pressing the retaining clips outwards.
2. Aling a DIMM on the socket such that the notch on the DIMM exactly match the notches in the
socket.
3. Firmly insert the DIMMinto the socket until the retaining clips snap back in place.
4. When installing the DIMM into the DIMM socket, we recommend to populate one DIMM in
   Channel A module and one in Channel B module for best performance.
   Please note that each logical DIMM must be made of two identical DIMMs having the same
   device size on each and the same DIMM size.
5. Reverse the installation steps when you wish to remove the DIMM module.




                                                   11
          GA-4KXSV-RH Motherboard

          2-3: Install expansion cards
English




          1. Read the related expansion card’s instruction document before install the expansion card into
              the computer.
          2. Remove your server’s chassis cover, necessary screws and slot bracket from the computer.
          3. Press the expansion card firmly into expansion slot in motherboard.
          4. Be sure the metal contacts on the card are indeed seated in the slot.
          5. Replace the screw to secure the slot bracket of the expansion card.
          6. Replace your computer’s chassis cover.
          7. Power on the computer, if necessary, setup BIOS utility of expansion card from BIOS.
          8. Install related driver from the operating system.




                                                           12
                                        Hardware Installation Process

2- 4: Connect ribbon cables, cabinet wires, and power
supply
2-4-1 : I/O Back Panel Introduction




                                 13
          GA-4KXSV-RH Motherboard

             PS/2 Keyboard and PS/2 Mouse Connector
English




             To install a PS/2 port keyboard and mouse, plug the mouse to the upper port (green) and the keyboard
             to the lower port (purple).
             Parallel Port
             The parallel port allows connection of a printer, scanner and other peripheral devices.
             Serial Port
             Modem can be connected to Serial port.
             VGA Port
             Monitor can be connected to VGA port.
             LAN Port
             The provided Internet connection is Gigabit Ethernet, providing data transfer speeds of
             10/100/1000Mbps.
             USB Port
             Before you connect your device(s) into USB connector(s), please make sure your device(s)
             such as USB keyboard, mouse, scanner, zip, speaker...etc. have a standard USB interface.
             Also make sure your OS supports USB controller. If your OS does not support USB controller,
             please contact OS vendor for possible patch or driver updated. For more information please
             contact your OS or device(s) vendors.
             Line In
             The default Line In jack. Devices like CD-ROM, walkman etc. can be connected to Line In jack.
             Line Out (Front Speaker Out)
             The default Line Out (Front Speaker Out) jack. Stereo speakers, earphone or front surround
             speakers can be connected to Line Out (Front Speaker Out) jack.
             MIC In
             The default MIC In jack. Microphone must be connected to MIC In jack.
             Surround Speaker Out (Rear Speaker Out)
             The default Surround Speaker Out (Rear Speaker Out) jack. Rear surround speakers can be
             connected to Surround Speaker Out (Rear Speaker Out) jack.
             Center/Subwoofer Speaker Out
             The default Center/Subwoofer Speaker Out jack. Center/Subwoofer speakers can be connected
             to Center/Subwoofer Speaker Out jack.
             Side Speaker Out
             The default Side Speaker Out jack. Surround side speakers can be connected to Side Speaker
             Out jack.




                                                           14
                                                           Hardware Installation Process

2-4-2 : LAN LED Description
Name         Color     Condition    Description
LAN            Green   ON           LAN Link / no Access
 Link/Activity Green   BLINK        LAN Access
           -           OFF          Idle
10/100 LAN Green       ON           100Mbps connection
Speed      -           OFF          10Mbps connection
GbE LAN Yellow         ON           1Gbps connection
Speed   Yellow         BLINK        Port identification with 1Gbps connection
        Green          ON           100Mbps connection
             Green     BLINK        Port identification with 10 or 100Mbps connection
             -         OFF          10Mbps connection




                                   15
          GA-4KXSV-RH Motherboard

          2- 5: Connectors Introduction
English




               18                 14       15



          16

                                                                             13
          6                                                          17
                                                                             22
                                                                                  1


          3              7
                                                                             19


          20
          4                                23
                        8

                    9        12
                    10

                                  11   5        2        21
               1) ATX                                    15) F_Audio
               2) ATX 12V                                16) Front Panel
               3) RAID IDE1                              17) IR
               4) RAID IDE2                              18) PWR_LED
               5) IDE                                    19) CPU FAN
               6) FDD                                    20) PWR FAN
               7) F_USB1                                 21) SYS FAN
               8) F_USB2                                 22) NB FAN
               9) SATA1                                  23) BAT (Battery)
               10) SATA2
               11) SATA3
               12) SATA4
               13) COMB
               14) CD_IN
                                                    16
                                                                               Connector Introduction
1 ) ATX (ATX Power Connector)
                                                    PIN No.    Definition
                                                                                          13
                                                    1          +3.3V                           1
                                                    2          +3.3V
                                                    3          GND
                                                    4          +5V
                                                    5          GND
                                                    6          +5V
                                                    7          GND
                                                    8          POK
                                                    9          5VSB
                                                    10         +12V
                                                    11         +12V
                                                    12         +3.3V
                                                    13         +3.3V
                                                    14         -12V
  AC power cord should only be connected to         15         GND
  your power supply unit after ATX power cable      16         PSON                            12
                                                                                          24
                                                    17         GND
  and other related devices are firmly connected
                                                    18         GND
  to the mainboard.                                 19         GND
                                                    20         -5V
                                                    21         +5V
                                                    22         +5V
                                                    23         +5V
                                                    24         GND




2 ) ATX_12V( +12V Power Connector)
                                                                     4 5




                                                                     1 8

                                                         Pin No.            Definition
                                                            1                  GND
                                                            2                  GND
                                                            3                  GND
                                                            4                  GND
                                                            5               P12V_CPU
 This connector (ATX +12V) is used only for                 6               P12V_CPU
                                                            7               P12V_CPU
 CPU1 Core Voltage.                                         8               P12V_CPU

                                               17
          GA-4KXSV-RH Motherboard
          3 /4 ) RAID IDE1/2 (RAID IDE Connectors)
English




            These two connectors are for RAID IDE hard disk. The red stripe of the ribbon cable must be the
            same side with the Pin1.
           RAID IDE1
                                                                                 39 40




          RAID IDE2
                                                                                  21




          5 ) IDE (IDE Connector)
            Please connect first hard disk to IDE1. The red stripe of the ribbon cable must be the same side with
            the Pin1.
                                                                                  39 40




                                                                                    21

                                                           18
                                                                             Connector Introduction
6 ) FDD (Floppy Connector)
  Please connect the floppy drive ribbon cables to FDD. It supports 720K,1.2M,1.44M and
  2.88Mbytes floppy disk types. The red stripe of the ribbon cable must be the same side with the
  Pin1.
                                                                     1 2




                                                                     33 34




7/8 ) F_USB1/F_USB2 (Front USB Connector)
  Be careful with the polarity of the front panel USB connector. Check the pin assignment while you
  connect the front panel USB cable. Please contact your nearest dealer for optional front panel
  USB cable.
  F_USB1

                                                       1 2              Pin No.    Definition
                                                                          1          Power
                                                                          2          Power
                                                                          3         USB DX-
                                                                          4         USB Dy-
                                                                          5        USB DX+
                                                                          6        USB Dy+
                                                                          7          GND
                                                                          8          GND
                                                        9 10
                                                                          9           NC
                                                                          10          NC




  F_USB2


                                               19
          GA-4KXSV-RH Motherboard
          9/10/11/12 ) S_ATA1/ 2/ 3/ 4 (Serial ATA Connectors)
English




             You can connect the Serial ATA device to this connector, it provides you high speed transfer rates
             (150MB/sec).




                                                                      7             Pin No.   Definition
                                                                                      1         GND
                                                                                      2         TXP
                                                                                      3         TXN
                                                                                      4         GND
                                                                                      5         RXN
                                                                                      6         RXP
                                                                      1               7         GND




                  SATA3
          SATA1           SATA4
            SATA2




          13 ) COMB


                                                                   10 9          Pin No.         Definition
                                                                                   1               DCD-
                                                                                   2               SIN2
                                                                                   3              SOUT2
                                                                                   4              DTR2-
                                                                                   5               GND
                                                                                   6              DSR2-
                                                                                   7              RTS2-
                                                                     2 1
                                                                                   8              CTS2-
                                                                                   9               RI2-
                                                                                   10               NC




                                                           20
                                                                                 Connector Introduction
14) CD_IN (CD In Connector)
   Connect CD-ROM or DVD-ROM audio out to the connector.




                                                                          Pin No.   Definition
                                                                             1       CD-L
                                                                            2        GND
                                                                            3        GND
                                                                1           4        CD-R




15) F_AUDIO (Front Audio Connector)
   If you want to use Front Audio connector, you must remove 5-6, 9-10 Jumper.
   In order to utilize the front audio header, your chassis must have front audio connector. Also please
   make sure the pin assigment on the cable is the same as the pin assigment on the MB header. To
   find out if the chassis you are buying support front audio connector, please contact your dealer.
   Please note, you can have the alternative of using front audio connector or of using rear audio
   connector to play sound.


                                                                          Pin No.   Definition
                                                                            1        MIC_L
                                                                            2        GND
                                                          2      10         3        MIC_R
                                                                            4        ACI_DET
                                                                            5        LINE_R
                                                          1      9
                                                                            6        GND
                                                                            7        F_Audio_JD
                                                                            8        No Pin
                                                                            9        LINE_L
                                                                            10       GND




                                                 21
          GA-4KXSV-RH Motherboard
          16 ) F_Panel1 (2X10 Pins Front Panel connector)
English




            Please connect the power LED, PC speaker, reset switch and power switch of your chassis
            front panel to the F_PANEL connector according to the pin assignment above.

                                                         Speaker Connector 1920

                                                                SPEAK-
                                                                                           Reset Switch
                                                               SPEAK+
                                                                                       NC
                                                                                        RES-
                                                                                             RES+
                                                                   MSG-                 HD-
                                                                   MSG+                 HD+
                                                            Message LED/         2 1
                                                            Power/                        IDE Hard Disk
                                                            Sleep LED                     Active LED




               HD (IDE Hard Disk Active LED)                  Pin 1: LED anode(+)
               (Blue)                                         Pin 2: LED cathode(-)
               SPEAK (Speaker Connector)                      Pin 1: VCC(+)
               (Amber)                                        Pin 2- Pin 3: NC
                                                              Pin 4: Data(-)
               RES (Reset Switch)                             Open: Normal Operation
               (Green)                                        Close: Reset Hardware System
               PW (Soft Power Connector)                      Open: Normal Operation
               (Red)                                          Close: Power On/Off
               MSG(Message LED/ Power/ Sleep LED)             Pin 1: LED anode(+)
               (Yellow)                                       Pin 2: LED cathode(-)
               NC (Purple)                                    NC




                                                       22
                                                                                  Connector Introduction
17) IR_CIR
   Make sure the pin 1 on the IR device is aling with pin one the connector. To enable the IR function
   on the board, you are required to purchase an option IR module. To use IR function only, please
   connect IR module to Pin1 to Pin5.


                                                                        Pin No.      Definition
                                                                          1           VCC(5V)
                                                                          2           Pin Removed
                                                                          3           IRRX
                                                                          4           GND
                                                                          5           IRTX




18) PWR_LED
   PWR_LED is connect with the system power indicator to indicate whether the system is on/off.
   It will blink when the system enters suspend mode. If you use dual color LED, power LED will turn
   to another color.



                                                                           Pin No.      Definition
                                                                              1          MPD+
                                                                    1         2           MPD-
                                                                              3           MPD-




                                                23
          GA-4KXSV-RH Motherboard
          19 )CPU_FAN (CPU Fan Connector)
English




             Please note, a proper installation of the CPU cooler is essential to prevent the CPU from running
             under abnormal condition or damaged by overheating.The CPU fan connector supports Max.
             current up to 1A .




                                                                          Pin No.         Definition
                                                                  1
                                                                            1                GND
                                                                            2                12V
                                                                            3               Sense
                                                                            4              Control




          20) PWR_FAN (Power Fan Connector)
             This connector allows you to link with the cooling fan on the system case to lower the system
             temperature.




                                                                      1       Pin No.   Definition
                                                                                 1       GND
                                                                                2        +12V
                                                                                3        Sense




                                                          24
                                                                               Connector Introduction
21) SYS_FAN (System Fan Connector)
   This connector allows you to link with the cooling fan on the system case to lower the system
   temperature.


                                                              1         Pin No.     Definition
                                                                           1         GND
                                                                           2         +12V
                                                                           3         Sense




22) NB_FAN (Chip Fan Connector)
   If you installed wrong direction, the chip fan will not work. Sometimes will damage the chip fan.
   (Usually black cable is GND)




                                                                  1
                                                                          Pin No.     Definition
                                                                             1         +12V
                                                                               2       GND




                                               25
          GA-4KXSV-RH Motherboard
          23 ) BAT1 (Battery)
English




                                                                              CAUTION
                                                               Danger of explosion if battery is incorrectly
                                                               replaced.
                                                               Replace only with the same or equivalent
                                                               type recommended by the manufacturer.
                                                               Dispose of used batteries according to the
                                                               manufacturer’s instructions.
          If you want to erase CMOS...
          1.Turn OFF the computer and unplug the power cord.
          2.Remove the battery, wait for 30 second.
          3.Re-install the battery.
          4.Plug the power cord and turn ON the computer.




                                                       26
                                           Jumper Setting

2- 6: Jumper Setting
                                              2
           3




       1

               7




           4 6
                       8
                   5


  1)   RUSB_PSEL                5)   JP1
  2)   FUSB_PSEL                6)   JP2
  3)   SUS_CLK                  7)   JP5
  4)   CLR_CMOS                 8)   JP6




                           27
          GA-4KXSV-RH Motherboard
          1 / 2 ) FUSB_PSEL/RUSB_PSEL (F_USB1 connector USB power source selection)
English




                                      RUSB_PSEL



                                                   1
                                                       1-2 close: P5V_DUAL

                                                       2-3 close: P5V (Default value)
                                                   1

                                                   1      1-2 close: P5V_DUAL
                                                   1      2-3 close: P5V (Default value)




          FUSB_PSEL




          3 ) SUS_CLK (TPM clock selection)




                                                       1 1-2 close: South Bridge (Deault value)

                                                       1 2-3 close: Crystal




                                              28
                                                                                 Jumper Setting
4 ) CLR_CMOS (Clear CMOS Function)
 You may clear the CMOS data to its default values by this jumper.
 Default value doesn’t include the “Shunter” to prevent from improper use this jumper. To
 clear CMOS, temporarily short 1-2 pin.



                                                            1-2 close: Clear CMOS
                                                    1

                                                            2-3 close: Normal (Default)
                                                    1




                                              29
          GA-4KXSV-RH Motherboard
          5 / 6 / 7 / 8 ) JP1/JP2/JP5/JP6 (PCI-X Bus Speedy Function)
English




            JP5




             JP1


                               JP2 JP6
                            PCI-X1                              PCI-X2
                     JP1    1. PCI                       JP5    1. PCI
                            2. PCI-X 66MHz                      2. PCI-X 66MHz
                     JP2    3. PCI-X 100MHz              JP6    3. PCI-X 100MHz
                            4. PCI 33MHz                        4. PCI 33MHz

                   PCI-X Compatibility
                   PCI-X 133MHz/100MHz                1 OPEN            2 OPEN
                   PCI-X 66MHz                        1 OPEN            2 CLOSE
                   PCI                                1 CLOSE           2 DON’T CARE

                   133MHZ Enabled
                    PCI-X 133MHz                      3 OPEN
                   PCI-X 100MHz                       3 CLOSE


                   66MHz Enabled
                   PCI 66MHz                          4 OPEN
                   PCI 33MHz                          4 CLOSE

                                                 30
                                                                               Motherboard Block Diagram

2- 7: Block Diagram


   Clock Generator
      ICS954148                       Intel Pentium4                  VID0~4
                                                                                  PWM/Other
                                          LGA775                                    Power

    Onboard VGA
                                                                                   Channel A
                                         GMCH
                                                                             DDRII SDRAM DIMMx2
                      PCIE Bus
     PCI Express                       (Lakeport)
      PCIE x16                            945G                                     Channel B
                                                                             DDRII SDRAM DIMMx2

                                            DMI        Hub Link

    USB Ports 0~7                                                 PCI Bus
                                                                               ITE8212 RAID

                      PCIE Bus                                    IDE Bus
     PCI Express                        ICH7R                                  IDE Primary
       PCIE x1                                                    SATA Bus
                                                                  LPC Bus       Serial ATA
                                  PCI Bus
    TEKOR 8257E
                                                                                Dual BIOS
                                       PCI Slot 1,2


    Intel 6700 PXH                     TPM SLD9630                             LPC I/O ITE8712G
   PCIE-PCIX Bridge
                          AC97 Link

                                        Front Panel/
                                          CPU Fan                                 I/O Ports:
        AC97/
                                                                               COMA COMB LPT
    Azalia ALC880
                                                                                  PS/2 FDD


    Audio Ports: Front Audio
    LIN_OUT LINE_IN MIC
    TELE CD_IN AUX_IN




                                                  31
                                                                                            BIOS Setup

Chapter 3                   BIOS Setup
BIOS (Basic Input and Output System) includes a CMOS SETUP utility which allows user to
configure
required settings or to activate certain system features.
The CMOS SETUP saves the configuration in the CMOS SRAM of the motherboard.
When the power is turned off, the battery on the motherboard supplies the necessary power to the
CMOS SRAM.
When the power is turned on, pushing the <Del> button during the BIOS POST (Power-On Self Test)
will take you to the CMOS SETUP screen. You can enter the BIOS setup screen by pressing "Ctrl
+ F1".
When setting up BIOS for the first time, it is recommended that you save the current BIOS to a disk
in the event that BIOS needs to be reset to its original settings. If you wish to upgrade to a new
BIOS, either
Gigabyte's Q-Flash or @BIOS utility can be used.
Q-Flash allows the user to quickly and easily update or backup BIOS without entering the operating
system.
@BIOS is a Windows-based utility that does not require users to boot to DOS before upgrading BIOS
but directly download and update BIOS from the Internet.

CONTROL KEYS
< >< ><      ><    > Move to select item
<Enter>              Select Item
<Esc>                Main Menu - Quit and not save changes into CMOS Status Page Setup Menu
                     and Option Page Setup Menu - Exit current page and return to Main Menu
<Page Up>            Increase the numeric value or make changes
<Page Down>          Decrease the numeric value or make changes
<F1>                 General help, only for Status Page Setup Menu and Option Page Setup Menu
<F2>                 Item Help
<F5>                 Restore the previous CMOS value from CMOS, only for Option Page Setup Menu
<F6>                 Load the file-safe default CMOS value from BIOS default table
<F7>                 Load the Optimized Defaults
<F8>                 Dual BIOS/Q-Flash utility
<F9>                 System Information
<F10>                Save all the CMOS changes, only for Main Menu



Main Menu
The on-line description of the highlighted setup function is displayed at the bottom of the screen.
Status Page Setup Menu / Option Page Setup Menu
Press F1 to pop up a small help window that describes the appropriate keys to use and the
possible selections for the highlighted item. To exit the Help Window press <Esc>.




                                                   33
GA-4KXSV-RH Motherboard
The Main Menu
Once you enter Award BIOS CMOS Setup Utility, the Main Menu (as figure below) will appear on the
screen. Use arrow keys to select among the items and press <Enter> to accept or enter the sub-menu.


                          CMOS Setup Utility-Copyright (C) 1984-2005 Award Software

          Standard CMOS Features                              Load Fail-Safe Defaults
          Advanced BIOS Features                              Load Optimized Defaults
          Integrated Peripherals                              Set Supervisor Password
          Power Management Setup                              Set User Password
          PnP/PCI Configurations                              Save & Exit Setup
          PC Health Status                                    Exit Without Saving
          Frequency/Voltage Control

      ESC: Quit                                                     : Select Item
      F8: Dual BIOS1/Q-Flash                                 F10: Save & Exit Setup
                                         Time, Date, Hard Disk Type...




         If you can't find the setting you want, please press "Ctrl+F1" to search the advanced option
         hidden.
         Please Load Optimized Defaults in the BIOS when somehow the system works not stable as
         usual. This action makes the system reset to the default for stability.

    Standard CMOS Features
    This setup page includes all the items in standard compatible BIOS.
    Advanced BIOS Features
    This setup page includes all the items of Award special enhanced features.
    Integrated Peripherals
    This setup page includes all onboard peripherals.
    Power Management Setup
    This setup page includes all the items of Green function features.
    PnP/PCI Configuration
    This setup page includes all the configurations of PCI & PnP ISA resources.
    PC Health Status
    This setup page is the System auto detect Temperature, voltage, fan, speed.
    Frequency/Voltage Control
    This setup page is control CPU clock and frequency ratio.
    Load Fail-Safe Defaults
    Fail-Safe Defaults indicates the value of the system parameters which the system would be in safe
    configuration.




                                                      34
                                                                                             BIOS Setup
Load Optimized Defaults
Optimized Defaults indicates the value of the system parameters which the system would be in best
performance configuration.
Set Supervisor Password
Change, set, or disable password. It allows you to limit access to the system and Setup, or just to Setup.
Set User Password
Change, set, or disable password. It allows you to limit access to the system.
Save & Exit Setup
Save CMOS value settings to CMOS and exit setup.
Exit Without Saving
Abandon all CMOS value changes and exit setup.




                                                 35
GA-4KXSV-RH Motherboard
2-1       Standard CMOS Features
                             CMOS Setup Utility-Copyright (C) 1984-2005 Award Software
                                              Standard CMOS Features
      Date (mm:dd:yy)                                Fri, Mar 18 2005                Item Help
      Time (hh:mm:ss)                                18:25:04                        Menu Level

      IDE Channel 0 Master                           [None]                          Change the day, month,
      IDE Channel 0 Slave                            [None]                          year
      IDE Channel 2 Master                           [None]
      IDE Channel 2 Slave                            [None]                          <Week>
      IDE Channel 3 Master                           [None]                          Sun. to Sat.
      IDE Channel 3 Slave                            [None]
                                                                                     <Month>
                                                                                     Jan. to Dec.
      Drive A                                        [1.44M, 3.5"]
      Drive B                                        [None]                          <Day>
      Floppy 3 Mode Suport                           [Disabled]                      1 to 31 (or maximum
                                                                                     allowed in the month)
      Halt On                                        [All, But Keyboard]
                                                                                     <Year>
      Base Memory                                    640K                            1999 to 2098
      Extended Memory                                511M



          : Move      Enter: Select      +/-/PU/PD: Value        F10: Save    ESC: Exit      F1: General Help
   F5: Previous Values                         F6: Fail-Safe Defaults         F7: Optimized Defaults




   Date
   The date format is <week>, <month>, <day>, <year>.
     Week            The week, from Sun to Sat, determined by the BIOS and is display only
     Month           The month, Jan. Through Dec.
     Day             The day, from 1 to 31 (or the maximum allowed in the month)
     Year            The year, from 1999 through 2098
   Time
   The times format in <hour> <minute> <second>. The time is calculated base on the 24-hour
   military-time clock. For example, 1 p.m. is 13:00:00.
   IDE Channel 0/2/3 Master, Slave
       IDE HDD Auto-Detection Press "Enter" to select this option for automatic device detection.
       IDE Chaneel 0 Master: You can use one of three methods:
         Auto        Allows BIOS to automatically detect IDE devices during POST(default)
         None        Select this if no IDE devices are used and the system will skip the automatic
                     detection step and allow for faster system start up.
         Manual      User can manually input the correct settings
       Access Mode    Use this to set the access mode for the hard drive. The four options are:
                      CHS/LBA/Large/Auto(default:Auto)
     Capacity         Capacity of currently installed hard disk.
   Hard drive information should be labeled on the outside drive casing. Enter the appropriate option
   based on this information.
       Cylinder           Number of cylinders
       Head               Number of heads
       Precomp            Write precomp
                                                         36
                                                                                                  BIOS Setup
       Landing Zone Landing zone
       Sector       Number of sectors
    Drive A / Drive B
   The category identifies the types of floppy disk drive A or drive B that has been installed in the
computer.
      None                No floppy drive installed
      360K, 5.25"        5.25 inch PC-type standard drive; 360K byte capacity.
      1.2M, 5.25"        5.25 inch AT-type high-density drive; 1.2M byte capacity
                         (3.5 inch when 3 Mode is Enabled).
      720K, 3.5"         3.5 inch double-sided drive; 720K byte capacity
      1.44M, 3.5"        3.5 inch double-sided drive; 1.44M byte capacity.
      2.88M, 3.5"        3.5 inch double-sided drive; 2.88M byte capacity.
    Floppy 3 Mode Support (for Japan Area)
       Disabled              Normal Floppy Drive. (Default value)
       Drive A               Drive A is 3 mode Floppy Drive.
       Drive B               Drive B is 3 mode Floppy Drive.
       Both                  Drive A & B are 3 mode Floppy Drives.
    Halt on
    The category determines whether the computer will stop if an error is detected during power up.
      No Errors           The system boot will not stop for any error that may be detected and you
                          will be prompted.
      All Errors          Whenever the BIOS detects a non-fatal error the system will be stopped.
      All, But Keyboard The system boot will not stop for a keyboard error; it will stop for all other
                          errors. (Default value)
      All, But Diskette   The system boot will not stop for a disk error; it will stop for all other errors.
      All, But Disk/Key   The system boot will not stop for a keyboard or disk error; it will stop for all
                          other errors.
    Memory
    The category is display-only which is determined by POST (Power On Self Test) of the BIOS.
       Base Memory
    The POST of the BIOS will determine the amount of base (or conventional) memory installed
    in the system.
    The value of the base memory is typically 512K for systems with 512K memory installed on
    the motherboard, or 640K for systems with 640K or more memory installed on the motherboard.
       Extended Memory
    The BIOS determines how much extended memory is present during the POST.
    This is the amount of memory located above 1 MB in the CPU's memory address map.
       Total Memory
    This item displays the memory size that used.




                                                      37
GA-4KXSV-RH Motherboard
2-2       Advanced BIOS Features
                          CMOS Setup Utility-Copyright (C) 1984-2005 Award Software
                                           Advanced BIOS Features
     Hard Disk Boot Priority                        [Press Enter]                  Item Help
     First Boot Device                              [Floppy]                       Menu Level
     Second Boot Device                             [Hard Disk]
     Third Boot Device                              [CDROM]                        Select Hard Disk Boot
     Password Check                                 [Setup]                        Device Priority
   # CPU Hyper-Threading                            [Enabled]
     Limit CPUID Max. to 3                          [Disabled]
     No-Execute Memory Protect (Note)               [Enabled]
     CPU Enhanced Halt (C1E) (Note)                 [Enabled]
     CPU Thermal Monitor 2(TM2) (Note)              [Enabled]
     CPU EIST Function (Note)                       [Enabled]
     On-Chip Frame Buffer Size                      [8MB]




          : Move    Enter: Select       +/-/PU/PD: Value        F10: Save   ESC: Exit      F1: General Help
   F3: Language1    F5: Previous Values       F6: Fail-Safe Defaults        F7: Optimized Defaults


          " # " System will detect automatically and show up when you install the Intel® Pentium® 4
          processor with HT Technology.

    Hard Disk Boot Priority
    Select boot sequence for onboard(or add-on cards) SCSI, RAID, etc.
    Use < > or < > to select a device, then press<+> to move it up, or <-> to move it down the list. Press
    <ESC> to exit this menu.
    First / Second / Third Boot Device
         Floppy              Select your boot device priority by Floppy.
         LS120               Select your boot device priority by LS120.
         Hard Disk           Select your boot device priority by Hard Disk.
         CDROM               Select your boot device priority by CDROM.
         ZIP                 Select your boot device priority by ZIP.
         USB-FDD             Select your boot device priority by USB-FDD.
         USB-ZIP             Select your boot device priority by USB-ZIP.
         USB-CDROM           Select your boot device priority by USB-CDROM.
         USB-HDD             Select your boot device priority by USB-HDD.
         LAN                 Select your boot device priority by LAN.
         Disabled            Select your boot device priority by Disabled.
    Password Check
         Setup             The system will boot but will not access to Setup page if the correct
                           password is not entered at the prompt. (Default value)
        System             The system will not boot and will not access to Setup page if the correct
                           password is not entered at the prompt.
    If you want to cancel the setting of password, please just press ENTER to make [SETUP] empty.
(Note)    This item will show up when you install a processor which supports this function.


                                                        38
                                                                                             BIOS Setup
    CPU Hyper-Threading
         Enabled       Enables CPU Hyper Threading Feature. Please note that this feature is only working
                       for operating system with multi processors mode supported. (Default value)
         Disabled      Disables CPU Hyper Threading.
    Limit CPUID Max. to 3
         Enabled       Limit CPUID Maximum value to 3 when use older OS like NT4.
         Disabled      Disables CPUID Limit for windows XP. (Default value)
    No-Execute Memory Protect (Note)
         Enabled       Enables No-Execute Memory Protect function. (Default value)
         Disabled      Disables No-Execute Memory Protect function.
    CPU Enhanced Halt (C1E) (Note)
         Enabled       Enables CPU Enhanced Halt (C1E) function. (Default value)
         Disabled      Disables CPU Enhanced Halt (C1E) function.
    CPU Thermal Monitor 2 (TM2) (Note)
         Enabled       Enable CPU Thermal Monitor 2 (TM2) function. (Default value)
         Disabled      Disable CPU Thermal Monitor 2 (TM2) function.
    CPU EIST Function (Note)
         Enabled       Enable CPU EIST function. (Default value)
         Disabled      Disable EIST function.
    On-Chip Frame Buffer Size
         1MB           Set On-chip frame buffer size to 1MB.
         8MB           Set On-chip frame buffer size to 8MB. (Default value)




(Note)    This item will show up when you install a processor which supports this function.


                                                   39
GA-4KXSV-RH Motherboard
2-3      Integrated Peripherals
                            CMOS Setup Utility-Copyright (C) 1984-2005 Award Software
                                              Integrated Peripherals
    On-Chip Primary PCI IDE                         [Enabled]                       Item Help
    SATA RAID/AHCI Mode                             [Disabled]                      Menu Level
    On-Chip SATA Mode                               [Auto]
  x PATA IDE Set to                                 Ch.0 Master/Slave
    SATA Port 0/2 Set to                            Ch.2 Master/Slave
    SATA Port 1/3 Set to                            Ch.3 Master/Slave
    USB Controller                                  [Enabled]
    USB 2.0 Controller                              [Enabled]
    USB Keyboard Support                            [Disabled]
    USB Mouse Support                               [Disabled]
    Legacy USB Storage detect                       [Enabled]
    Azalia Codec                                    [Auto]
    Onboard H/W GigaRAID                            [Enabled]
    GigaRAID Function                               [RAID]
    Onboard H/W LAN                                 [Enabled]
    Onboard LAN Boot ROM                            [Disabled]
    Onboard Serial Port 1                           [3F8/IRQ4]
    Onboard Serial Port 2                           [2F8/IRQ3]


         : Move      Enter: Select      +/-/PU/PD: Value        F10: Save    ESC: Exit      F1: General Help
  F5: Previous Values                         F6: Fail-Safe Defaults         F7: Optimized Defaults


                            CMOS Setup Utility-Copyright (C) 1984-2005 Award Software
                                              Integrated Peripherals
    Onboard Parallel Port                           [378/IRQ7]                      Item Help
    Parallel Port Mode                              [SPP]                           Menu Level
  x ECP Mode Use DMA                                3




         : Move      Enter: Select      +/-/PU/PD: Value        F10: Save    ESC: Exit      F1: General Help
  F5: Previous Values                         F6: Fail-Safe Defaults         F7: Optimized Defaults




      On-Chip Primary PCI IDE
        Enabled                Enable onboard 1st channel IDE port. (Default value)
        Disabled               Disable onboard 1st channel IDE port.




                                                        40
                                                                                        BIOS Setup
SATA RAID / AHCI Mode
  RAID                     Set the onboard SATA controller to RAID mode.
  AHCI                     Set the onboard SATA controller to AHCI mode. Advanced Host
                           Controller Interface (AHCI) is an interface specification that allows the
                           storage driver to enable advanced Serial ATA features such as Native
                           Command Queuing and hot plug. For more details about AHCI, please
                           visit Intel's website.
  Disabled                 Set the onboard SATA controller to IDE mode. (Default value)
On-Chip SATA Mode
  Disabled                 Disable this function.
  Auto                     BIOS will auto detect. (Default value)
   Combined                Set On-Chip SATA mode to Combined, you can use up to 4 HDDs on
                           the motherboard; 2 for SATA and the other for PATA IDE.
  Enhanced                 Set On-Chip SATA mode to Enhanced, the motherboard allows up to 6
                           HDDs to use.
  Non-Combined             Set On-Chip SATA mode to Non-Combined, SATA will be simulated to
                           PATA mode.
PATA IDE Set to
  Ch.1 Master/Slave        Set PATA IDE to Ch. 1 Master/Slave. (Default value)
  Ch.0 Master/Slave        Set PATA IDE to Ch. 0 Master/Slave.
SATA Port 0/2 Set to
   This value will auto make by the setting "On-Chip SATA Mode" and "PATA IDE Set to".
If PATA IDE were set to Ch. 1 Master/Slave,this function will auto set to Ch. 0 Master/Slave.
SATA Port 1/3 Set to
    This value will auto make by the setting "On-Chip SATA Mode" and "PATA IDE Set to".
If PATA IDE were set to Ch. 0 Master/Slave,this function will auto set to Ch. 1 Master/Slave.
USB Controller
  Enabled                  Enable USB Controller. (Default value)
  Disabled                 Disable USB Controller.
USB 2.0 Controller
Disable this function if you are not using onboard USB 2.0 feature.
   Enabled                   Enable USB 2.0 Controller. (Default value)
   Disabled                  Disable USB 2.0 Controller.
USB Keyboard Support
  Enabled                  Enable USB Keyboard Support.
  Disabled                 Disable USB Keyboard Support. (Default value)
USB Mouse Support
  Enabled                  Enable USB Mouse Support.
  Disabled                 Disable USB Mouse Support. (Default value)
Legacy USB Storage detect
  Enabled                  Enable legacy USB storage detect. (Default value)
  Disabled                 Disable legacy USB storage detect.



                                              41
GA-4KXSV-RH Motherboard
   Azalia Codec
     Auto                  Auto detect Azalia audio function. (Default value)
     Disabled              Disable Azalia audio function.
   Onboard H/W GigaRAID
     Enabled      Enable Onboard H/W GigaRAID function. (Default value)
     Disabled     Disable this function.
   GigaRAID Function
     RAID         Select onboard GigaRAID chip function as RAID. (Default value)
     ATA          Select onboard GigaRAID chip function asa ATA.
   Onboard H/W LAN
     Enabled      Enable Onboard H/W LAN function. (Default value)
     Disabled     Disable this function.
   Onboard Onboard LAN Boot ROM
     Enabled      Enable Onboard Onboard LAN Boot ROM function.
     Disabled     Disable this function. (Default value)
   Onboard Serial Port 1
     Auto         BIOS will automatically setup the port 1 address.
     3F8/IRQ4     Enable onboard Serial port 1 and address is 3F8/IRQ4. (Default value)
     2F8/IRQ3     Enable onboard Serial port 1 and address is 2F8/IRQ3.
     3E8/IRQ4     Enable onboard Serial port 1 and address is 3E8/IRQ4.
     2E8/IRQ3     Enable onboard Serial port 1 and address is 2E8/IRQ3.
     Disabled     Disable onboard Serial port 1.
   Onboard Serial Port 2
     Auto         BIOS will automatically setup the port 1 address.
     3F8/IRQ4     Enable onboard Serial port 2 and address is 3F8/IRQ4.
     2F8/IRQ3     Enable onboard Serial port 2 and address is 2F8/IRQ3. (Default value)
     3E8/IRQ4     Enable onboard Serial port 2 and address is 3E8/IRQ4.
     2E8/IRQ3     Enable onboard Serial port 2 and address is 2E8/IRQ3.
     Disabled     Disable onboard Serial port 2.
   Onboard Parallel port
     Disabled     Disable onboard LPT port.
     378/IRQ7     Enable onboard LPT port and address is 378/IRQ7. (Default value)
     278/IRQ5     Enable onboard LPT port and address is 278/IRQ5.
     3BC/IRQ7     Enable onboard LPT port and address is 3BC/IRQ7.
   Parallel Port Mode
     SPP          Using Parallel port as Standard Parallel Port. (Default value)
     EPP          Using Parallel port as Enhanced Parallel Port.
     ECP          Using Parallel port as Extended Capabilities Port.
     ECP+EPP      Using Parallel port as ECP & EPP mode.
   ECP Mode Use DMA
     3            Set ECP Mode Use DMA to 3. (Default value)
     1            Set ECP Mode Use DMA to 1.



                                              42
                                                                                                    BIOS Setup
2-4     Power Management Setup
                            CMOS Setup Utility-Copyright (C) 1984-2005 Award Software
                                            Power Management Setup
    ACPI Suspend Type                               [S1(POS)]                       Item Help
    Soft-Off by PWR-BTTN                            [Instant-off]                   Menu Level
    PME Event Wake Up                               [Enabled]
    Power On by Ring                                [Enabled]
    Resume by Alarm                                 [Disabled]
  x Date (of Month) Alarm                           Everyday
  x Time (hh:mm:ss) Alarm                           0:0:0
    Power On By Mouse                               [Disabled]
    Power On By Keyboard                            [Disabled]
  x KB Power ON Password                            Enter
    AC Back Function                                [Soft-Off]




         : Move      Enter: Select      +/-/PU/PD: Value        F10: Save    ESC: Exit      F1: General Help
  F5: Previous Values                         F6: Fail-Safe Defaults         F7: Optimized Defaults




   ACPI Suspend Type
      S1(POS)            Set ACPI suspend type to S1/POS(Power On Suspend). (Default value)
      S3(STR)            Set ACPI suspend type to S3/STR(Suspend To RAM).
   Soft-off by PWR-BTTN
      Instant-off        Press power button then Power off instantly. (Default value)
      Delay 4 Sec.       Press power button 4 sec. to Power off. Enter suspend if button is pressed
                         less than 4 sec.
   PME Event Wake Up
      Disabled           Disable this function.
      Enabled            Enable PME Event Wake up. (Default value)
   Power On by Ring
      Disabled           Disable Power on by Ring function.
      Enabled            Enable Power on by Ring function. (Default value)
   Resume by Alarm
   You can set "Resume by Alarm" item to enabled and key in Date/time to power on system.
      Disabled        Disable this function. (Default value)
      Enabled         Enable alarm function to POWER ON system.
   If Resume by Alarm is Enabled.
      Date (of Month) Alarm :        Everyday, 1~31
      Time (hh: mm: ss) Alarm :      (0~23) : (0~59) : (0~59)
   Power On By Mouse
      Disabled           Disabled this function. (Default value)
      Double Click       Double click on PS/2 mouse left button to power on the system.


  Only for GA-8I945G Pro.

                                                        43
GA-4KXSV-RH Motherboard
   Power On By Keyboard
     Password            Enter from 1 to 5 characters to set the Keyboard Power On Password.
     Disabled            Disabled this function. (Default value)
     Keyboard 98         If your keyboard have "POWER Key" button, you can press the key to
                         power on the system.
   KB Power ON Password
   When "Power On by Keyboard" set at Password, you can set the password here.
     Enter             Input password (from 1 to 5 characters) and press Enter to set the Keyboard
                       Power On password.
   AC Back Function
     Soft-Off            When AC-power back to the system, the system will be in "Off" state.
                         (Default value)
     Full-On             When AC-power back to the system, the system always in "On" state.
     Memory              When AC-power back to the system, the system will return to the Last state
                         before AC-power off.




                                                44
                                                                                                     BIOS Setup
2-5      PnP/PCI Configurations
                             CMOS Setup Utility-Copyright (C) 1984-2005 Award Software
                                              PnP/PCI Configurations
      PCI 1 IRQ Assignment                           [Auto]                                  Item Help
      PCI 2 IRQ Assignment                           [Auto]                          Menu Level




         : Move     Enter: Select       +/-/PU/PD: Value        F10: Save     ESC: Exit      F1: General Help
  F3: Language1     F5: Previous Values       F6: Fail-Safe Defaults          F7: Optimized Defaults



   PCI 1 IRQ Assignment
       Auto                              Auto assign IRQ to PCI 1. (Default value)
       3,4,5,7,9,10,11,12,14,15          Set IRQ 3,4,5,7,9,10,11,12,14,15 to PCI 1.
   PCI 2 IRQ Assignment
       Auto                              Auto assign IRQ to PCI 2. (Default value)
       3,4,5,7,9,10,11,12,14,15          Set IRQ 3,4,5,7,9,10,11,12,14,15 to PCI 2.




  Only for GA-8I945G Pro.


                                                        45
GA-4KXSV-RH Motherboard
2-6      PC Health Status
                            CMOS Setup Utility-Copyright (C) 1984-2005 Award Software
                                                PC Health Status
      Vcore                                         OK                                       Item Help
      VCC18                                         OK                               Menu Level
      +3.3V                                         OK
      +5V                                           OK
      +12V                                          OK
      5VSB                                          OK
      Current CPU Temperature                       47oC
      Current CPU FAN Speed                          RPM
      Current POWER FAN Speed                        RPM
      Current SYSTEM FAN Speed                       RPM
      CPU Warning Temperature                       [Disabled]
      CPU FAN Fail Warning                          [Disabled]
      POWER FAN Fail Warning                        [Disabled]
      SYSTEM FAN Fail Warning                       [Disabled]
      CPU Smart FAN Control                         [Enabled]
      CPU Smart FAN Mode                            [Auto]




         : Move      Enter: Select      +/-/PU/PD: Value        F10: Save     ESC: Exit      F1: General Help
  F5: Previous Values                         F6: Fail-Safe Defaults          F7: Optimized Defaults



   Current Voltage(V) Vcore / VCC18V / +3.3V / +5V / +12V / 5VSB
       Detect system's voltage status automatically.
   Current CPU Temperature
       Detect CPU temperature automatically.
   Current CPU/POWER/SYSTEM FAN Speed (RPM)
       Detect CPU/POWER/SYSTEM Fan speed status automatically.
   CPU Warning Temperature
       60 oC / 140 o F        Monitor CPU temperature at 60 oC /        140 oF.
       70 oC / 158 o F        Monitor CPU temperature at 70 oC /        158 oF.
       80 oC / 176 o F        Monitor CPU temperature at 80 oC /        176 oF.
       90 oC / 194 o F        Monitor CPU temperature at 90 oC /        194 oF.
       Disabled               Disable this function. (Default value)
   CPU/POWER /SYSTEM FAN Fail Warning
       Disabled               Fan warning function disable. (Default value)
       Enabled                Fan warning function enable.
   CPU Smart FAN Control
       Disabled          Disable this function.
       Enabled           When this function is enabled, CPU fan will run at different speed depending on
                         CPU temperature. Users can adjust the fan speed with Easy Tune based on
                         their requirements.




                                                        46
                                                                                   BIOS Setup
CPU Smart FAN Mode
This option is available only when CPU Smart FAN Control is enabled.
  Auto             BIOS autodetects the type of CPU fan you installed and sets the optimal CPU
                   Smart FAN control mode for it. (Default Value)
  Voltage          Set to Voltage when you use a CPU fan with a 3-pin fan power cable.
  PWM              Set to PWM when you use a CPU fan with a 4-pin fan power cable.
Note: In fact, the Voltage option can be used for CPU fans with 3-pin or 4-pin power cables.
However, some 4-pin CPU fan power cables are not designed following Intel 4-Wire fans PWM
control specifications. With such CPU fans, selecting PWM will not effectively reduce the fan
speed.




                                            47
GA-4KXSV-RH Motherboard
2-7       Frequency/Voltage Control
                            CMOS Setup Utility-Copyright (C) 1984-2005 Award Software
                                        MB Intelligent Tweaker(M.I.T.)
    Robust Graphics Booster                         [Auto]                                  Item Help
    C.A.M                                           [High]                          Menu Level
    CPU Host Clock Control                          [Disabled]
  x CPU Host Frequency (Mhz)                        200
    System Memory Multiplier                        [Auto]
  x Memory Frequency (Mhz)                          667




         : Move      Enter: Select      +/-/PU/PD: Value        F10: Save    ESC: Exit      F1: General Help
  F5: Previous Values                         F6: Fail-Safe Defaults         F7: Optimized Defaults



         Wrong frequency may cause system can’t boot. Clear CMOS will overcome wrong
         frequency setting issue.


      Robust Graphics Booster
      Select the options can enhance the VGA graphics card bandwidth to get higher performance.
        Auto            Set Robust Graphics Booster to Auto. (Default value)
        Fast            Set Robust Graphics Booster to Fast.
        Turbo           Set Robust Graphics Booster to Turbo.
      C.A.M
        High             Set clock ratio for frequency-locked CPU to High. (Default value)
        Low              Set clock ratio for frequency-locked CPU to Low.
      CPU Host Clock Control
      Please note that if your system is overclocked and cannot restart, please wait 20secs.
      for automatic system restart or clear the CMOS setup data and perform a safe restart.
         Disabled       Disable CPU Host Clock Control. (Default value)
         Enabled        Enable CPU Host Clock Control.
      CPU Host Frequency (Mhz)
          100MHz ~ 600MHz       Set CPU Host Frequency from 100MHz to 600MHz.
      If you use FSB533 Pentium 4 processor, please set "CPU Host Frequency" to 133MHz.If you use
      FSB800 Pentium 4 processor, please set "CPU Host Frequency" to 200MHz.
      Incorrect using it may cause your system broken. For power End-User use only!
          Auto           Set Memory frequency by DRAM SPD data. (Default value)




                                                        48
                                                                              BIOS Setup
System Memory Multiplier
Wrong frequency may make system can't boot, clear CMOS to overcome wrong frequency issue.
for FSB(Front Side Bus) frequency=533MHz,
   3             Memory Frequency = Host clock X 3.
   4             Memory Frequency = Host clock X 4.
   Auto          Set Memory frequency by DRAM SPD data. (Default value)
for FSB(Front Side Bus) frequency=800MHz,
   2.0           Memory Frequency = Host clock X 2.0.
   2.66          Memory Frequency = Host clock X 2.66.
   3.33          Memory Frequency = Host clock X 3.33.
   Auto          Set Memory frequency by DRAM SPD data. (Default value)
for FSB(Front Side Bus) frequency=1066MHz,
   1.5           Memory Frequency = Host clock X 1.5.
   2.0           Memory Frequency = Host clock X 2.0.
   2.5           Memory Frequency = Host clock X 2.5.
   Auto          Set Memory frequency by DRAM SPD data. (Default value)
Memory Frequency (Mhz)
The values depend on CPU Host Frequency (Mhz) and System Memory Multiplier setting.




                                         49
GA-4KXSV-RH Motherboard
2-8      Load Fail-Safe Defaults
                          CMOS Setup Utility-Copyright (C) 1984-2005 Award Software

          Standard CMOS Features                               Load Fail-Safe Defaults
          Advanced BIOS Features                               Load Optimized Defaults
          Integrated Peripherals                               Set Supervisor Password
          Power Management Setup                               Set User Password
          PnP/PCI Configurations       Load Fail-Safe Defaults (Y/N)? N
                                                               Save & Exit Setup
          PC Health Status                                     Exit Without Saving
          Frequency/Voltage Control

      ESC: Quit                                                     : Select Item
      F8: Dual BIOS1/Q-Flash                                 F10: Save & Exit Setup
                                            Load Fail-Safe Defaults



Fail-Safe defaults contain the most appropriate values of the system parameters that allow minimum
system performance.




2-9      Load Optimized Defaults
                          CMOS Setup Utility-Copyright (C) 1984-2005 Award Software

          Standard CMOS Features                             Load Fail-Safe Defaults
          Advanced BIOS Features                             Load Optimized Defaults
          Integrated Peripherals                             Set Supervisor Password
          Power Management Setup                             Set User Password
          PnP/PCI Configurations                              (Y/N)? N
                                      Load Optimized DefaultsSave & Exit Setup
          PC Health Status                                   Exit Without Saving
          Frequency/Voltage Control

      ESC: Quit                                                      : Select Item
      F8: Dual BIOS1/Q-Flash                                  F10: Save & Exit Setup
                                            Load Optimized Defaults


Selecting this field loads the factory defaults for BIOS and Chipset Features which the system
automatically detects.




                                                      50
                                                                                         BIOS Setup
2-10 Set Supervisor/User Password
                           CMOS Setup Utility-Copyright (C) 1984-2005 Award Software

         Standard CMOS Features                                Load Fail-Safe Defaults
         Advanced BIOS Features                                Load Optimized Defaults
         Integrated Peripherals                                Set Supervisor Password
         Power Management Setup                                Set User Password
         PnP/PCI Configurations Enter Password:                Save & Exit Setup
         PC Health Status                                      Exit Without Saving
         Frequency/Voltage Control

     ESC: Quit                                                        : Select Item
     F8: Dual BIOS1/Q-Flash                                    F10: Save & Exit Setup
                                            Change/Set/Disable Password



When you select this function, the following message will appear at the center of the screen to
assist you in creating a password.
Type the password, up to eight characters, and press <Enter>. You will be asked to confirm the
password. Type the password again and press <Enter>. You may also press <Esc> to abort the
selection and not enter a password.
To disable password, just press <Enter> when you are prompted to enter password. A message
"PASSWORD DISABLED" will appear to confirm the password being disabled. Once the password
is disabled, the system will boot and you can enter Setup freely.
The BIOS Setup program allows you to specify two separate passwords:
SUPERVISOR PASSWORD and a USER PASSWORD. When disabled, anyone may access all
BIOS Setup program function. When enabled, the Supervisor password is required for entering the
BIOS Setup program and having full configuration fields, the User password is required to access
only basic items.
If you select "System" at "Password Check" in Advance BIOS Features Menu, you will be
prompted for the password every time the system is rebooted or any time you try to enter Setup
Menu.
If you select "Setup" at "Password Check" in Advance BIOS Features Menu, you will be prompted
only when you try to enter Setup.




                                                        51
GA-4KXSV-RH Motherboard
2-11 Save & Exit Setup
                           CMOS Setup Utility-Copyright (C) 1984-2005 Award Software

           Standard CMOS Features                          Load Fail-Safe Defaults
           Advanced BIOS Features                          Load Optimized Defaults
           Integrated Peripherals                          Set Supervisor Password
           Power Management Setup                          Set User Password
           PnP/PCI Configurations                          Save & Exit Setup
           PC Health Status                                Exit Without
                                       Save to CMOS and EXIT (Y/N)? Y Saving
           Frequency/Voltage Control

      ESC: Quit                                                      : Select Item
      F8: Dual BIOS1/Q-Flash                                  F10: Save & Exit Setup
                                              Save Data to CMOS


Type "Y" will quit the Setup Utility and save the user setup value to RTC CMOS.
Type "N" will return to Setup Utility.




2-12 Exit Without Saving
                           CMOS Setup Utility-Copyright (C) 1984-2005 Award Software

           Standard CMOS Features                              Load Fail-Safe Defaults
           Advanced BIOS Features                              Load Optimized Defaults
           Integrated Peripherals                              Set Supervisor Password
           Power Management Setup                              Set User Password
           PnP/PCI Configurations         Quit Without Saving (Y/N)? NExit Setup
                                                               Save &
           PC Health Status                                    Exit Without Saving
           Frequency/Voltage Control

      ESC: Quit                                                      : Select Item
      F8: Dual BIOS1/Q-Flash                                  F10: Save & Exit Setup
                                                Abandon all Data


Type "Y" will quit the Setup Utility without saving to RTC CMOS.
Type "N" will return to Setup Utility.




   Only for GA-8I945G Pro.

                                                       52
                                                                               INTEL RAID BIOS Configuration

Chapter 4                        INTEL RAID BIOS Configuration
Configuring the Intel RAID BIOS
The Intel RAID BIOS setup lets you choose the RAID array type and which hard drives you want to
make part of the array.
Entering the RAID BIOS Setup
1. After rebooting your computer, wait until you see the RAID software prompting you to press Ctrl + I.
The RAID prompt appears as part of the system POST and boot process prior to loading the OS. You
have a few seconds to press Ctrl + I before the window disappears.


        Intel(R) Matrix Storage Manager option ROM V5.0.0.1011 ICH7R wRAID5
        Copyright(C) 2003-04 Intel Corporation. All Rights Reversed.

        RAID Volumes :
        None Defined.

        Physical Disks :
        Port     Driver Model        Serial #                       Size    Type/Status(Vol ID)
        0        ST3120026AS         3JT354CP                       111.7GB Non-RAID Disk
        1        ST3120026AS         3JT329JX                       111.7GB Non-RAID Disk

        Press <CTRL - I> to enter Configuration Utility




Press Ctrl + I. The Intel RAID Utility - Create RAID Volume window appears (as illustrated below).


                      Intel(R) Matrix Storage Manager option ROM V5.0.0.1011 ICH7R wRAID5
                             Copyright(C) 2003-04 Intel Corporation. All Rights Reversed.
                                                 [ MAIN MENU ]
                                            1. Create RAID Volume
                                            2. Delete RAID Volume
                                            3. Reset Disks to Non-RAID
                                            4. Exit

                                       [ DISK/VOLUME INFORMATION ]
           RAID Volumes :
           None Defined.

           Physical Disks :
           Port     Driver Model        Serial #                         Size    Type/Status(Vol ID)
           0        ST3120026AS         3JT329JX                         111.7GB Non-RAID Disk
           1        ST3120026AS         3JT354CP                         111.7GB Non-RAID Disk




                  [   ]-Select                      [ESC]-Exit                    [ENTER]-Select Menu




                                                          53
GA-4KXSV-RH Motherboard
Create RAID Volume
Press Enter under Create RAID Volume to set up RAID.
                    Intel(R) Matrix Storage Manager option ROM V5.0.0.1011 ICH7R wRAID5
                           Copyright(C) 2003-04 Intel Corporation. All Rights Reversed.
                                        [ CREATE VOLUME MENU ]
                                   Name : RAID_Volume0
                              RAID Level : RAID0(Stripe)
                                    Disks : Select Disks
                                Strip Size : 128KB
                                Capacity : 223.5 GB
                                             Create Volume
                                                   [ HELP ]

                        Enter a string between 1 and 16 characters in length that can be used
                      to uniquely identify the RAID volume. This name is case sensitive and
                                          can not contain special characters.




              [   ]-Change        [TAB]-Next             [ESC]-Previous Menu             [ENTER]-Select

After entering the Create Volume Menu, you can set disk name with 1~16 letters (letters cannot be
special characters) under Name item.
After setting disk name, press Enter to select RAID Level.

                    Intel(R) Matrix Storage Manager option ROM V5.0.0.1011 ICH7R wRAID5
                           Copyright(C) 2003-04 Intel Corporation. All Rights Reversed.
                                        [ CREATE VOLUME MENU ]
                                   Name : RAID_Volume0
                              RAID Level : RAID0(Stripe)
                                    Disks : Select Disks
                                Strip Size : 128KB
                                Capacity : 223.5 GB
                                             Create Volume
                                                   [ HELP ]
                            Choose the RAID level best suited to your usage model.
                    RAID0- Data striped across multiple physical drives for performance.
                    RAID1- Data mirrored across multiple physical drives for redundancy.
                    RAID0+1- Striped volume whose segments are RAID 1 volumes. Requires
                            four hard drives. Functionally equivalent to RAID 0+1.
                    RAID5- Data and parity striped across three or more physical drives
                             for performance and redundancy.

              [   ]-Change        [TAB]-Next             [ESC]-Previous Menu             [ENTER]-Select


There are four RAID levels: RAID0(Stripe), RAID1(Mirror), RAID 0+1 (Striping + Mirroring) and RAID5.
After selecting the RAID level, press Enter to select Strip Size.




                                                       54
                                                                               INTEL RAID BIOS Configuration
The KB is a unit of Strip Size. You can set disk block size with this item.
The disk block size can be set from 4KB to 128KB. After you set disk block size, press Enter to set
disk Capacity.

                    Intel(R) Matrix Storage Manager option ROM V5.0.0.1011 ICH7R wRAID5
                           Copyright(C) 2003-04 Intel Corporation. All Rights Reversed.
                                          [ CREATE VOLUME MENU ]
                                     Name : RAID_Volume0
                                RAID Level : RAID0(Stripe)
                                      Disks : Select Disks
                                  Strip Size : 128KB
                                  Capacity : 223.5 GB
                                               Create Volume
                                                    [ HELP ]

                                           The following are typical values:
                                               RAID 0 - 128KB
                                               RAID 1 - 64KB
                                               RAID 5 - 64KB




              [   ]-Change          [TAB]-Next           [ESC]-Previous Menu              [ENTER]-Select




                    Intel(R) Matrix Storage Manager option ROM V5.0.0.1011 ICH7R wRAID5
                           Copyright(C) 2003-04 Intel Corporation. All Rights Reversed.
                                          [ CREATE VOLUME MENU ]
                                     Name : RAID_Volume0
                                RAID Level : RAID0(Stripe)
                                      Disks : Select Disks
                                  Strip Size : 128KB
                                  Capacity : 223.5 GB
                                               Create Volume
                                                    [ HELP ]


                             Enter the volume capacity. The default value indicates the
                             maximum volume capacity using the selected disks. If less
                             than the maximum capacity is chosen, creation of a second
                             volume is needed to utilize the remaining space.



              [   ]-Change          [TAB]-Next           [ESC]-Previous Menu              [ENTER]-Select

Press Enter to enter Create Volume after setting disk capacity.




                                                       55
GA-4KXSV-RH Motherboard
Press Enter under the Create Volume item.
                     Intel(R) Matrix Storage Manager option ROM V5.0.0.1011 ICH7R wRAID5
                            Copyright(C) 2003-04 Intel Corporation. All Rights Reversed.
                                        [ CREATE VOLUME MENU ]
                                   Name : RAID_Volume0
                              RAID Level : RAID0(Stripe)
                                    Disks : Select Disks
                                Strip Size : 128KB
                                Capacity : 223.5 GB
                                             Create Volume
                                                   [ HELP ]



                                 Press "ENTER" to Create the specified volume




               [   ]-Change       [TAB]-Next            [ESC]-Previous Menu         [ENTER]-Select




An alert bar will be displayed warning you that all data on selected disks will be lost. Please press Y
to complete the set-up of RAID.
                     Intel(R) Matrix Storage Manager option ROM V5.0.0.1011 ICH7R wRAID5
                            Copyright(C) 2003-04 Intel Corporation. All Rights Reversed.
                                       [ CREATE VOLUME MENU ]
                                  Name : RAID_Volume0
                             RAID Level : RAID0(Stripe)
                                   Disks : Select Disks
                               Strip Size : 128KB
                               Capacity : 223.5 GB
                                            Create Volume
                        WARNING : ALL DATA ON [SELECTED DISKS WILL BE LOST.
                                                  HELP ]
                              Are you sure you want to creat this volume? (Y/N) :

                                 Press "ENTER" to Create the specified volume




               [   ]-Change       [TAB]-Next            [ESC]-Previous Menu         [ENTER]-Select




                                                      56
                                                                      INTEL RAID BIOS Configuration
After the completion, you will see the detailed information about the RAID, such as RAID level, disk
block size, disk name and disk capacity, etc.

                     Intel(R) Matrix Storage Manager option ROM V5.0.0.1011 ICH7R wRAID5
                            Copyright(C) 2003-04 Intel Corporation. All Rights Reversed.
                                              [ MAIN MENU ]
                                         1. Create RAID Volume
                                         2. Delete RAID Volume
                                         3. Reset Disks to Non-RAID
                                         4. Exit

                                     [ DISK/VOLUME INFORMATION ]
          RAID Volumes :
          ID      Name                          Level                 Strip     Size      Status
          Bootable
          0       RAID_Volume0       RAID(Stripe)       128KB         223.5GB   Normal    Yes

          Physical Disks :
          Port     Driver Model      Serial #                         Size      Type/Status(Vol ID)
          0        ST3120026AS       3JT329JX                         111.7GB   Member Disk(0)
          1        ST3120026AS       3JT354CP                         111.7GB   Member Disk(0)

                 [   ]-Select                    [ESC]-Exit                     [ENTER]-Select Menu




Delete RAID Volume
If you want to delete a RAID volume, please select the Delete RAID Volume option. Press Enter key
and follow the instructions on the screen.

                     Intel(R) Matrix Storage Manager option ROM V5.0.0.1011 ICH7R wRAID5
                            Copyright(C) 2003-04 Intel Corporation. All Rights Reversed.
                                              [ MAIN MENU ]
                                         1. Create RAID Volume
                                         2. Delete RAID Volume
                                         3. Reset Disks to Non-RAID
                                         4. Exit

                                     [ DISK/VOLUME INFORMATION ]
          RAID Volumes :
          ID      Name                          Level                 Strip     Size      Status
          Bootable
          0       RAID_Volume0       RAID(Stripe)       128KB         223.5GB   Normal    Yes

          Physical Disks :
          Port     Driver Model      Serial #                         Size      Type/Status(Vol ID)
          0        ST3120026AS       3JT329JX                         111.7GB   Member Disk(0)
          1        ST3120026AS       3JT354CP                         111.7GB   Member Disk(0)

                 [   ]-Select                    [ESC]-Exit                     [ENTER]-Select Menu




                                                    57

				
DOCUMENT INFO
Shared By:
Categories:
Stats:
views:12
posted:9/6/2010
language:English
pages:57