Docstoc

Slips

Document Sample
Slips Powered By Docstoc
					                   Safety is an individual responsibility. You can use the best equipment




Slips, Trips, and Falls in Construction




All you have to do is look around........the potential for slipping, tripping and falls is everywhere. At home,
on the job and during recreation. It appears that slips and falls are just a fact of life and nothing can be
done about them. Well, that's just not true and that's what this program's all about. Preventing slips, trips
and falls on construction sites.

Let's explain some terminology, then we'll discuss how to prevent these potentially harmful injuries. A
foot-level fall is one when the person falls to the same level on which he or she was walking or standing.
There are basically two kinds of hazards that account for more than 90 percent of all foot-level falls.
Slipping hazards and tripping hazards. A person may slip on grease or wet surfaces and fall. A person
could trip and fall over some obstacle on a floor surface.

People slip and fall because of one or more of the following causes:

1. Traction robbing substances on the floor surface, such as water, oil, grease, sand, mud, ice and other
substances.

2. Flooring offers too little traction, such as metal floor worn smooth from abrasive traffic, or smooth
finished concrete.

3. Traction robbing condition associated with shoes, such as hard leather heels, metal heel plates, worn
heels, slippery substances on soles or heels.

4. Another factor in slipping in falling is the individual is not watching where he or she is going. In other
words, not paying attention.

These factors present us with some hazard recognition and prevention techniques, such as inspecting
walkways and floor surfaces regularly. Check daily for slip and fall hazards. Be alert for drips or spills from
oil, grease, liquids, water and slippery granular material. Promptly correct any noted hazard since delay
exposes more people to the hazard. Don't forget to correct the source of the hazard. Whenever possible,
use non- skid flooring. Floor areas subject to accumulations of slippery substances should be frequently
cleaned or have some type of non-skid flooring installed.

Everyone on the jobsite has a responsibility to clean up spills as they occur. Spills create slipping
hazards, so when you see a spill, clean it up.....don't wait for someone else to clean it up.

There are always chronic trouble spots on jobsites. Specific locations often become slipping hazards due
to routine accumulations of oil, grease or other materials. Such locations should be studied to see if such
accumulations can be prevented.

All employees have an obligation to report hazards to their supervisor, if a problem can't be corrected
immediately. Certainly, wearing appropriate footwear is one of the bestÊ prevention methods. Metal heel
plates on heels of shoes and boots can be hazardous when walking on rigid surfaces, such as wood or
metal.
                  Safety is an individual responsibility. You can use the best equipment




Make sure walkways and other frequently used floor areas are adequately illuminated. Replace burned
out lights and correct dark shadow-casting conditions. Everyone needs to see where they're going, so
make sure dark areas are well lit. Tripping hazards pose special problems, so it takes special effort to
reduce these hazards. Floor conditions or objects on floors that present an obstacle to foot movement are
considered tripping hazards. Tripping hazards include cables, ropes, tools, boxes, lumber, legs of
equipment, and faulty flooring. Many such obstacles result from poor housekeeping. Here are some tips
to help prevent tripping hazards.

1. Be sure there is adequate storage facilities. When items are scattered around, or stored improperly,
this indicates a lack of storage facilities or persons are not properly storing their equipment, tools and
other items. Poor housekeeping is one of the major causes of tripping hazards.

2. Cleaning and disposal equipment can significantly improve housekeeping, so make sure there is
adequate cleaning and disposal equipment to maintain good housekeeping. Maintain as you go, is a good
policy.

3. Overhead instead of underfoot, is an old saying on jobsites. Basically it means to run cables, hoses,
ropes and wires overhead instead o? along the floor. Where such items must be run on the floor, it should
be straight, flat and shielded or marked for easy identification. Portable warning signs and blinker lights
are useful to attract attention to such tripping hazards.

4. Inspect floor surfaces frequently. Regular daily inspections of walkways and working areas is
necessary and to correct any deficiencies found during these inspections.

5. Of course, tripping prevention wouldn't be complete without housekeeping. Good housekeeping means
establishing a place for everything, such as tools, materials, portable equipment, waste, scrap and seeing
to it that everything is kept in its proper place when not in use.

The most important aspect of reducing tripping hazards is for everyone to watch where they're going.
Sure, you get busy, have a lot of things to do, but it doesn't take a lot of effort to watch where you're
walking. Watch for un-level surfaces, holes, lumber, cables, cords and other hazards and take the action
necessary to prevent a trip and fall. Now let's take a few minutes to talk about fall to below accidents. A
fall to below accident is one in which a person falls to a level below that on which he was walking,
standing or working. These types of falls can be quite serious.

The two most common situations involved are working above ground or floor level and working at or
around ground or floor openings. Working above ground could be a person overextending his reach on a
ladder, causing the ladder to kick out sideways, causing a fall to the ground.

Working at or around ground or floor openings could be a person falling down an elevator shaft or falling
through a floor opening. Let's take a look at some potential problems and what you can do about them.
When you're working on ladders, platforms, scaffolding or on permanent structures, be sure to use proper
procedures and caution.

1. Make sure the equipment used was erected safely. Ladders in particular should be at the proper angle,
with firm footing.

2. Don't use defective equipment. Ladders, structural members of wooden staging and so on. Inspect
before you use the equipment.

3. When using scaffolds, make sure there are guardrails to prevent falls.
                   Safety is an individual responsibility. You can use the best equipment




4. Work safely and with caution, as there may be tripping or slipping hazards on structures or flooring
surfaces.

5. Use safety belts or nets when working above ground, when not protected from falls by the use of
guardrails.

6. Guard openings or barricade where necessary to keep persons from falling through the opening. Use
warning devices, such as signs or lights. Temporary floor or ground openings should never be left
unattended, unless marked with suitable warning devices. Keep in mind, however, that warning signs and
lights are no permanent substitute for barricades.

There are literally hundreds of techniques, rules and procedures to prevent slips, trips and falls, but none
are more effective than the effort each individual devotes to watching for hazards, then avoiding the
hazard. If you're attentive to where you're walking and avoid the hazard...... there's no slip, trip and fall. If
you exercise caution around floor openings....there's no slip, trip and fall. If you maintain good
housekeeping on the jobsite, keep tools and equipment out of the way....there's no slip, trip or fall. If you
use safe, serviceable equipment, such as ladders and scaffolding, and you position the ladders and
scaffolding properly....there's no slip, trip and fall.

				
DOCUMENT INFO
Shared By:
Categories:
Stats:
views:16
posted:8/9/2010
language:English
pages:3
Description: safety