Docstoc

JR 783 - Geistware

Document Sample
JR 783 - Geistware Powered By Docstoc
					                            JR 783                   AIRPLANE MODE                                     - Command Flow Path
        Model Setup
                                                               Selection
        TX OFF
Step      Up- -Mode- Down
1                           Push these two buttons     MDL                       pg.25 model number selection 1 to 8
                            simultaneously & hold                   |
                Enter                                  NAME                      pg.26 model name, 4 letters only
                                                                    |
2       Turn TX on                                     TYPE                      pg.27 model type, ACRO, HELI, GLID
                                                               |
                                                       MDL RSET                  pg.28 model name, 4 letters only
          Up- -Mode- Down                                      |
3                           Scroll through options     mix WING NORM             pg.29 wing mixing, NORM, FLPR(flaperon), DELT(delta)
                            using one of these                 |
                Enter       buttons                    MODU                      pg.32 modulation selection, S-PCM, Z-PCM, PPMF
                                                               |                       Z-PCM shows as Z, PPMF shows a F, S-PCM no display
                                                               |
                                                       SPOI                      pg.33   Spoil Channel Input Selection - assign swtich from POT (aux 2 knob) or MXSW (mixing switch)
                                                               |
                                                       CPV                       pg.34 copy selection, copy one model to another




       Model Function
                                                               Selection
        TX ON
Step      Up- -Mode- Down
1                           Push these two buttons     DUAL-RATE                 pg.35 use Ch key to toggle between Ailer, Elev, Rudder, & Auto Rudd
                            simultaneously & hold                   |
                Enter                                  EXP                       pg.37 exponential, use Ch key to toggle between Ailer, Elev, Rudder, select LINear or from 0 to 100%
                                                                    |
                                                       REVERSE SW                pg.39 use Ch key to toggle between channels, use "= or -" keys to change servoe rotation
                                                                    |
                                                               SUBTRIM           pg.39 use Ch key to toggle between channels, use "= or -" keys to change values
          Up- -Mode- Down                                           |
2                           Scroll through options                T.ADJ          pg.40 use Ch key to toggle between channels, use "= or -" keys to change values for amount of servoe throw
                            using one of these                      |
                Enter       buttons                    MIX E-F                   pg.41 elev flap mixing, flap switch must be in position to make adjustments
                                                                    |
                                                       LD                        pg.42 landing altitude, couple spoilers, set in INH (inhibit)
3         +             -   use the + - key to                      |
                            change values              SNP.R                     pg.44 to set snap roll or INH (inhibit)
                                                                    |
                                                       mix DIFF                  pg.46 differential aileron mixing (only in flaperon or elevon mixing is active)
                                                                    |
          Up- -Mode- Down                              MIX A                     pg.47   set mixing, + key selects master channel, - key selects slave channel, press ch to select stick or switch activation
4                           To exit, push both                      |
                            buttons simultaneously     MIX B                     pg.47 set mixing, + key selects master channel, - key selects slave channel
                Enter       buttons                                 |
                                                       MIX C                     pg.47 set mixing, + key selects master channel, - key selects slave channel
                                                                    |
                                                       MIX D                     pg.47 set mixing, + key selects master channel, - key selects slave channel
                                                                    |
                                                       MIX E                     pg.47 set mixing, + key selects master channel, - key selects slave channel
                                                                    |
                                                       MIX F                     pg.47 set mixing, + key selects master channel, - key selects slave channel
                                                                    |
                                                         TRIM                    pg.51 fly airplane and trim, land airplane and leave trims in place.
                                                                          MEMO         access trim offset command, screen will show MEMO
                                                         OFFSET                        by pressing the + or - keys the screen will change to MOV.T, trims have been memorized
                                                                                       move trims levers back to neutral positions and press CLR key on far right
                                                                                       exit out of trim command by simultaneoulsy pressing the UP DN keys.
                                                                                        if trim amount is too large, OVER appears on screen
                                                                                         adjust the lever that has too much trim to a smaller position and mechanically adjust linkage for that surface.


                                                       FLP.P t.adj               pg.53 flap knop value adjustment
                                                                    |
                                                       FAL.S                     pg.54 fail safe, for PCM modes, note- in S-PCM mode set fail safe mode for each channel.
                                                                    |
                                                       TRN                       pg.59 trainer functions
                                                                    |
                                                       TIMR                      pg.61 timer functions, use CH key to toggle screen to show time. Use + or - keys to start timer.
                                                                    |
                                                       TIMR                      pg.62 intergrated timer, tracks time by model use, use CLR key to clear.

				
DOCUMENT INFO
Shared By:
Categories:
Tags:
Stats:
views:8
posted:6/15/2010
language:English
pages:1