Survey on 802 by lonyoo

VIEWS: 10 PAGES: 10

									                           Survey on 802.11
Introduction:
Over recent years, the market for wireless communications has enjoyed
tremendous growth. Wireless technology now reaches or is capable of reaching
virtually every location on the face of the earth. Hundreds of millions of people
exchange information every day using pagers, cellular telephones, and other
wireless communication products. Seeing the tremendous success of wireless
telephony and messaging services, wireless communication has been applied to
the realm of personal and business computing. The protocol that personal and
business computers use to communicate over a wireless medium is 802.11
This protocol was adopted by IEEE standards committee in 1997 and is the first
wireless LAN (WLAN) standard. This standard defines the media access control
(MAC) and physical (PHY) layers for a LAN with wireless connectivity. It
addresses local area networking where the connected devices communicate
over the air to other devices that are within close proximity to each other.

How did 802.11come into the picture?
The IEEE 802.11 protocol is an extension of the IEEE 802.3 protocol for wired
networks.
IEEE 802.3 standard
The IEEE 802.3 standard is most widely used standard for wired network which
was developed out of the original work done on Ethernet. Ethernet was
developed by Xerox corporation's Palo Alto research center (PARC) in the 1970s
and was the technological basis for the IEEE 802.3 specification, which was
initially released in 1980. Today, the term Ethernet is often used to refer to all
carrier sense multiple access/collision detection (CSMA/CD) LAN’s that generally
conform to Ethernet specifications, including IEEE 802.3.
The 802.3 protocol has many implementations that are available and to
distinguish between them the committee has developed a concise notation.
<data rate in Mbps><signaling method><maximum length in hundreds of
meters>
The defined alternatives for a 10Mbps date rate are
      10BASE5
      10BASE2
      10BASE-T (T= Twisted Pair)
      10BASE-F (F= Optical Fiber)
The defined alternatives for a 100Mbps data rate are
      100BASE-TX
      100BASE-FX
      100BASE-T4

802.11 Versus 802.3
The 802.11 standard is similar in most respects to the IEEE 802.3 Ethernet
standard. Specifically, the 802.11 standard addresses:

      Functions required for an 802.11 compliant device to operate either in a
       peer-to-peer fashion or integrated with an existing wired LAN
      Operation of the 802.11 device within possibly overlapping 802.11
       wireless LANs and the mobility of this device between multiple wireless
       LANs
      MAC level access control and data delivery services to allow upper layers
       of the 802.11 network
      Several physical layer signaling techniques and interfaces
      Privacy and security of user data being transferred over the wireless
       media

There are a number of characteristics that are unique to the wireless
environment (as compared to a wired LAN) that the 802.11 standard must take
into consideration. The physical characteristics of a wireless LAN introduce range
limitations, unreliable media and dynamic topologies where stations move about,
interference from outside sources, and lack of the ability for every device to ‘hear’
every other device within the WLAN. These limitations force the WLAN standard
to create fundamental definitions for short-range LANs made up of components
that are within close proximity of each other. Larger geographic coverage is
handled by building larger LANs from the smaller fundamental building blocks or
by integrating the smaller WLANs with an existing wired network.

Mobility

Mobility of wireless stations is the most important feature of a wireless LAN. A
WLAN would not serve much purpose if stations were not able to move about
freely from location to location either within a specific WLAN or between different
WLAN ‘segments’.

For compatibility purposes, the 802.11 MAC must appear to the upper layers of
the network as a ‘standard’ 802 LAN. The 802.11 MAC layer is forced to handle
station mobility in a fashion that is transparent to the upper layers of the 802 LAN
stack. This forces functionality into the 802.11 MAC layer that is typically handled
by upper layers.

The IEEE 802.11 Wireless LAN Architecture

The 802.11 architecture is comprised of several components and services that
interact to provide station mobility transparent to the higher layers of the network
stack.

Wireless LAN Station
The station (STA) is the most basic component of the wireless network. A station
is any device that contains the functionality of the 802.11 protocol, that being
MAC, PHY, and a connection to the wireless media. Typically the 802.11
functions are implemented in the hardware and software of a network interface
card (NIC).

A station could be a laptop PC, handheld device, or an Access Point. Stations
may be mobile, portable, or stationary and all stations support the 802.11 station
services of authentication, de-authentication, privacy, and data delivery.

Basic Service Set (BSS)
802.11 defines the Basic Service Set (BSS) as the basic building block of an
802.11 wireless LAN. The BSS consists of a group of any number of stations.

802.11 Topologies

Independent Basic Service Set (IBSS)
The most basic wireless LAN topology is a set of stations, which have recognized
each other and are connected via the wireless media in a peer-to-peer fashion.
This form of network topology is referred to as an Independent Basic Service Set
(IBSS) or an Ad-hoc network.

In an IBSS, the mobile stations communicate directly with each other. Every
mobile station may not be able to communicate with every other station due to
the range limitations. There are no relay functions in an IBSS therefore all
stations need to be within range of each other and communicate directly.

IBSS




- Independent Basic Service Set (IBSS)

Infrastructure Basic Service Set
An Infrastructure Basic Service Set is a BSS with a component called an Access
Point (AP). The access point provides a local relay function for the BSS. All
stations in the BSS communicate with the access point and no longer
communicate directly. All frames are relayed between stations by the access
point. This local relay function effectively doubles the range of the IBSS.
The access point may also provide connection to a distribution system.

Distribution System




- Infrastructure Basic Service Set

Distribution System (DS)

The distribution system (DS) is the means by which an access point
communicates with another access point to exchange frames for stations in their
respective BSSs, forward frames, to follow mobile stations as they move from
one BSS to another, and exchange frames with a wired network.
As IEEE 802.11 describes it, the distribution system is not necessarily a network
nor does the standard place any restrictions on how the distribution system is
implemented, only on the services it must provide. Thus the distribution system
may be a wired network like 803.2 or a special purpose box that interconnects
the access points and provides the required distribution services.

Extended Service Set (ESS)

Extending coverage via an Extended Service Set (ESS) 802.11 extends the
range of mobility to an arbitrary range through the Extended Service Set (ESS).
An extended service set is a set of infrastructure BSS’s, where the access points
communicate amongst themselves to forward traffic from one BSS to another, to
facilitate movement of stations between BSS’s.
The access point performs this communication through the distribution system.
The distribution system is the backbone of the wireless LAN and may be
constructed of either a wired LAN or wireless network.
Typically the distribution system is a thin layer in each access point that
determines the destination for traffic received from a BSS. The distribution
system determines if traffic should be relayed back to a destination in the same
BSS, forwarded on the distribution system to another access point, or sent into
the wired network to a destination not in the extended service set.
Communications received by an access point from the distribution system are
transmitted to the BSS to be received by the destination mobile station.
Network equipment outside of the extended service set views the ESS and all of
its mobile stations as a single MAC-layer network where all stations are
physically stationary. Thus, the ESS hides the mobility of the mobile stations from
everything outside the ESS. This level of indirection provided by the 802.11
architecture allows existing network protocols that have no concept of mobility to
operate correctly with a wireless LAN where there is mobility.




Figure 4 - Extended Service Set (ESS)

Distribution Services

Distribution services provide functionality across a distribution system. Typically,
access points provide distribution services. The five distribution services and
functions detailed below include: association, disassociation, re-association,
distribution, and integration.

Association
The association service is used to make a logical connection between a mobile
station and an access point. Each station must become associated with an
access point before it is allowed to send data through the access point onto the
distribution system. The connection is necessary in order for the distribution
system to know where and how to deliver data to the mobile station.
The mobile station invokes the association service once and only once, typically
when the station enters the BSS. Each station can associate with one access
point though an access point can associate with multiple stations.

Disassociation
The disassociation service is used either to force a mobile station to eliminate an
association with an access point or for a mobile station to inform an access point
that it no longer requires the services of the distribution system. When a station
becomes disassociated, it must begin a new association to communicate with an
access point again.

An access point may force a station or stations to disassociate because of
resource restraints, the access point is shutting down or being removed from the
network for a variety of reasons. When a mobile station is aware that it will no
longer require the services of an access point, it may invoke the disassociation
service to notify the access point that the logical connection to the services of the
access point from this mobile station is no longer required.

Stations should disassociate when they leave a network, though there is nothing
in the architecture to assure this happens. Disassociation is a notification and
can be invoked by either associated party. Neither party can refuse termination of
the association.

Re-association
Re-Association enables a station to change its current association with an
access point. The re-association service is similar to the association service, with
the exception that it includes information about the access point with which a
mobile station has been previously associated. A mobile station will use the re-
association service repeatedly as it moves through out the ESS, loses contact
with the access point with which it is associated, and needs to become
associated with a new access point.

By using the re-association service, a mobile station provides information to the
access point to which it will be associated and information pertaining to the
access point which it will be disassociated. This allows the newly associated
access point to contact the previously associated access point to obtain frames
that may be waiting there for delivery to the mobile station as well as other
information that may be relevant to the new association.

The mobile station always initiates re-association.

Distribution
Distribution is the primary service used by an 802.11 station. A station uses the
distribution service every time it sends MAC frames across the distribution
system. The distribution service provides the distribution with only enough
information to determine the proper destination BSS for the MAC frame.

The three association services (association, re-association, and disassociation)
provide the necessary information for the distribution service to operate.
Distribution within the distribution system does not necessarily involve any
additional features outside of the association services, though a station must be
associated with an access point for the distribution service to forward frames
properly.

Integration
The integration service connects the 802.11 WLAN to other LANs, including one
or more wired LANs or 802.11 WLANs. A portal performs the integration service.
The portal is an abstract architectural concept that typically resides in an access
point though it could be part of a separate network component entirely.

The integration service translates 802.11 frames to frames that may traverse
another network, and vice versa.

802.11 Media Access Control

The 802.11 MAC layer provides functionality to allow reliable data delivery for the
upper layers over the wireless PHY media. The data delivery itself is based on an
asynchronous, best-effort, connectionless delivery of MAC layer data. There is
no guarantee that the frames will be delivered successfully.

The 802.11 MAC provides a controlled access method to the shared wireless
media called Carrier-Sense Multiple Access with Collision Avoidance
(CSMA/CA). CSMA/CA is similar to the collision detection access method
deployed by 802.3 Ethernet LANs.

Another function of the 802.11 MAC is to protect the data being delivered by
providing security and privacy services. Security is provided by the authentication
services and by Wireless Equivalent Privacy (WEP), which is an encryption
service for data delivered on the WLAN.

CSMA/CA

The fundamental access method of 802.11 is Carrier Sense Multiple Access with
Collision Avoidance or CSMA/CA. CSMA/CA works by a "listen before talk
scheme". This means that a station wishing to transmit must first sense the radio
channel to determine if another station is transmitting. If the medium is not busy,
the transmission may proceed.

The CSMA/CA protocol avoids collisions among stations sharing the medium by
utilizing a random backoff time if the station’s physical or logical sensing
mechanism indicates a busy medium. The period of time immediately following a
busy medium is the highest probability of collisions occurring, especially under
high utilization.
The CSMA/CA scheme implements a minimum time gap between frames from a
given user. Once a frame has been sent from a given transmitting station, that
station must wait until the time gap is up to try to transmit again. Once the time
has passed, the station selects a random amount of time (the backoff interval) to
wait before "listening" again to verify a clear channel on which to transmit. If the
channel is still busy, another backoff interval is selected that is less than the first.
This process is repeated until the waiting time approaches zero and the station is
allowed to transmit. This type of multiple access ensures judicious channel
sharing while avoiding collisions.

802.11 Physical Layer (PHY)

The 802.11 physical layer (PHY) is the interface between the MAC and the
wireless media where frames are transmitted and received. The PHY provides
three functions. First, the PHY provides an interface to exchange frames with the
upper MAC layer for transmission and reception of data. Secondly, the PHY uses
signal carrier and spread spectrum modulation to transmit data frames over the
media. Thirdly, the PHY provides a carrier sense indication back to the MAC to
verify activity on the media.

802.11 provides three different PHY definitions: Both Frequency Hopping Spread
Spectrum (FHSS) and Direct Sequence Spread Spectrum (DSSS) support 1 and
2 Mbps data rates.

802.11b

Operating in the 2.4GHz frequency range, 802.11b (aka Wi-Fi) has a nominal
maximum data rate of 11Mbps, with the potential of three simultaneous channels.
802.11b has a great advantage in that it is accepted worldwide. One of the more
significant disadvantages of 802.11b is that the frequency band is crowded, and
subject to interference from other networking technologies, microwave ovens,
2.4GHz cordless phones (a huge market), and Bluetooth. There are drawbacks
to 802.11b, including lack of interoperability with voice devices, and no QoS
provisions for multimedia content. Interference and other limitations aside,
802.11b is the clear leader in business and institutional wireless networking and
is gaining share for home applications as well.

802.11a

802.11a, is much faster than 802.11b, with a 54Mbps maximum data rate
(actually increased to 72Mbps or 108Mbps in a non-standard double-speed
mode depending on the chipset vendor and component manufacturer). 802.11a
(Wi-Fi5) operates in the 5GHz frequency range and allows eight simultaneous
channels. One big advantage to 802.11a is that it isn't subject to interference
from Bluetooth or any of the other 2.4GHz frequency denizens.

One big disadvantage is that it is not directly compatible with 802.11b, and
requires new bridging products that can support both types of networks, although
if you don't mind spending the money for access points for both 11a and 11b, you
can plug them into hubs or better yet, switches on your network and they'll work
just fine. Other clear disadvantages are that 802.11a is only available in half the
bandwidth in Japan (for a maximum of four channels), and it isn't approved for
use in Europe, where HiperLAN2 is the standard.

Like 802.11b, 802.11a has no provisions to optimize voice or multimedia content.

802.11g

802.11g, operates in the 2.4GHz frequency with mandatory compatibility with
802.11b but with a maximum data rate of 54Mbps

The standard operates entirely in the 2.4GHz frequency, but uses a minimum of
two modes (both mandatory) with two optional modes. The mandatory
modulation/access modes are the same CCK (Complementary Code Keying)
mode used by 802.11b (hence the compatibility with Wi-Fi) and the OFDM
(Orthogonal Frequency Division Multiplexing) mode used by 802.11a (but in this
case in the 2.4GHz frequency band). The mandatory CCK mode supports
11Mbps and the OFDM mode has a maximum of 54Mbps. There are also two
modes that use different methods to attain a 22Mbps data rate--TI's PBCC-22
(Packet Binary Convolutional Coding, rated for 6 to 54Mbps) and Intersil's CCK-
OFDM mode (with a rated max of 33Mbps).

The obvious advantage of 802.11g is that it maintains compatibility with 802.11b
(and 802.11b's worldwide acceptance) and also offers faster data rates
comparable with 802.11a. The number of channels available, however, is not
increased, since channels are a function of bandwidth, not radio signal
modulation and on that score, 802.11a wins with its eight channels, compared to
the three channels available with either 802.11b or 802.11g. Another
disadvantage of 802.11g is that the 2.4GHz frequency will get even more
crowded

								
To top