Docstoc

XV Manual

Document Sample
XV Manual Powered By Docstoc
					MULTI GAUGE for VW                          AUDI           XV Series                                                                                                                             (XV / As of December, 2009 No.4)



USER’S GUIDE
Thank you for purchasing PIVOT “XV”.                                                                                                                                                             MULTI GAUGE ø60
                                                                                                                                                                                                                   XV
Please read these instructions carefully before installing or using this device.
Please do not lose this user’s guide, as you will held liable for the cost of reissuing it.                                                                                                 EURO SPEC
              CAUTION                        Improper use or disregard of these warnings may result in
                                             the injury or death of people.                                                                  NOTE              Improper use or disregard of these warnings may cause
                                                                                                                                                               injury to persons, damage the product and other things.


  ●Do not work in areas where ●Do not crush the                              ●Do not operate while driving                         ●This product is for DC12V cars;                place subject to high temperature or
   there is excessive exhaust  cable                                            Operating or checking the display                      Installation cannot be carried out on       any place where water may be
    Due to vehicle exhaust emission         Please be careful that the          during driving may cause an accident;                  cars with other voltage batteries.          splashed
    poisoning or fire may result in a       cable dose not get                  please use with the utmost
                                                                                                                                   ●Just after installation do not               ●Make sure to replace all screws and
    damage to humans.                       crushed by the seat rail or         consideration for safety.
                                                                                                                                    exert any strong force on the                 parts to their original place
                                            car door steel plate, nor
  ●Please securely fasten the                                                ●Please be sure to store bundle                        product
                                            cut by any sharp steel                                                                                                               ●Do not install the product in a place
    product to a stable place
                                            plate as this may cause a         away all wires with tape, etc...                         When double-sided tape is used for an  where it will cause distraction
    It is very dangerous if, while in       poor connection or an               It is very dangerous to pull tangled                   installation be warned that when hot
    use, the product falls off and          electric short leading to           wires by force or allow tangled wires                  the tape temporarily losses           ●Do not, in any manner, process, take
    interferes with braking.                fire or other danger.               to interfere with driving.                             adhesiveness.                          apart, or make changes to this
                                                                                                                                                                                   product
                                                                                                                                   ●Do not install the product in any

           1. The display will not be proper if the ECU being used is not the standard one or if a sub-computer is being used, even in compatible car models.
           2. Cannot be used in combination with products that use another company’s diagnostic monitoring connectors.
           3. For details about using in combination with other PIVOT products please see our Web Site at http://pivotjp.com/information/obd_conjunction-e.html.


Check the contents
                                                                 4p Coupler with           Fuse Power                                     Allen          Zip Tie   Double-sided      Cushion        Cut           User’s
                                                   Meter                                                        Adjustable Stand
                                                                 OBD2 Connector              Cable                                       Wrench                       Tape            Tape        Connector       Guide




    FEATURES                                              With our XV multi-gauge, just by connecting to the diagnostic monitoring connector, the VW and AUDI specialized CAN
                                                          communication can be analyzed and three types of data can be displayed. (Not for use with incompatible models)


                                Switch between 3 types of display in the same unit                                                     New Controller provides needle
 3 types of display             (Boost, Water Temperature and Oil Temperature)
                                                                                                          Smooth Action                action quick and smooth
                                                                                                                                                                                   PEAK HOLD           Display peak reading


                     Same Standard Indigo Blue Illumination (XV)                                                           Stepping motor drive brings you a high-performance display with no hunching
 Illumination        Same Standard White Illumination (XV-A)
                                                                                               Stepping Drive              or overshooting

                            It is possible to connect directly using the coupler to the diagnostic monitoring connector meaning
 Easy-installation          there is no need for troublesome wiring



Displays and Uses
1. Boost           (Absolute pressure display               1)    2. Water Temp                                      3. Oil Temp                                    4. Peak Hold
   Display          -100〜154Kpa                                         Display         -40℃〜155℃                        Display           -40℃〜195℃                      Use     Check the peak readings

             ●Check Boost                                                       ●Prevention of                                         ●Check engine oil                ※Only the peak value on display will be
   Use                                                                  Use                                              Use                                             measured; measurements are not taken
             ●For Eco-driving [Vacuum]                                           overheating                                            temperature etc.
                                                                                                                                                                         for items other than that one on display.
                                                                                ●Check Heating etc.
         [Boost]                        [Vacuum]
                                                                                                                                                                       【Reference Peak Values】
                                                                                                                                                                        ・BOOST
                                                                                                                                                                          GOLF GTI (BWA Turbo) = about 95Kpa
                                                                                                                                                                          GOLF GT TSI (BLG Twin Charger) = about 140Kpa
                                                                                                                                                                        ・WATER TEMP 80〜100 ˚C
                                                                                                                                                                        ・OIL TEMP 80〜120 ˚C




       Ex:70Kpa                         Ex:-40Kpa                                Ex:95˚C                                               Ex:120˚C
                                                                                                                                                                    Opening Demo
※1 This display of absolute pressure includes barometric pressure and may differ from a gauge showing relative pressure
                                                                                                                                                                    Turning the key ON (engine start) will
  (mechanical type).                                                                                                                                                display the opening demo one time.
※1 With the key in the ON position, due to altitude the boost needle may show a minus reading.



     WIRING METHOD
                    with the key in the
    Please carry out wiring                                                                                                      Connect to Power                  1      Insert the OBD2 connector
                                                                                                                                      (IGN)
    OFF position and take out the key.                                                                Connector
                                                                                                                                       Not as normal                   Locate the diagnostic monitoring
                                                                                                      on the car
                                                                                                                                       power source                    connector position.
       LOCK
      (OFF)                                                                                           OBD2
                                                                                                              (
                                                                                                      connector ※2)
                   +                                                                                    Red
                                                                                                                                                  Fuse
                                                                                                                    Extra wire
      Take out                                              Backside
                                                                                                       Black (connect to 3-DRIVE)
      the Key                                                                                                    ※Not normally used.                                                                     Diagnostic monitoring
                                                                                                                                                                                                         connector
    ※2 When inserting, make sure that                                                                                  Red
       the OBD2 connector is placed in                                  4p coupler              1p coupler                                                           Diagnostic monitoring connector
                                                                                                                                                                   Diagnostic monitoring connector
       the proper direction.

                                                                                                                                                                    Completely insert
Notes about using the OBD2 connector
                                                                                                                                                                    the OBD2 connector.
                                          Make sure to grip the            If you unable to get a grip on the distended portions
                                          distended portions when         With some car models it may be
                                          pulling it out or inserting     difficult to get a good grip on the                                                                        OBD2 connector
                                          it.                             connector.                                                     In such cases,
                                                                                                                                         use a lock tie to
      Do not pull on the wires when trying to remove
      the connector; the wires may become
                                                                                                                                         push or pull the
                                                                                                                                         connector.
                                                                                                                                                                                        Next, connect to
      disconnected.                                                                                                                                                                     the power source
                     Please carry out wiring            with the key in the OFF position and the key removed.                                                  LOCK
                                                                                                                                                              (OFF)              +       Remove
                                                                                                                                                                                         the key



        Connecting to a Power Source  The following is different example arewiring toof how tobox of a GOLF Vcontact your dealer. wheel on right).
                                                    is just one          of          the fuse                 GTI BWA (steering
 2                                    If your model              and you     unsure           connect please

                                                                         Insert with the
                                                                         connecting wire                                                                                   If you are unable to get power from
                                                                         at the bottom.                                                                                    the fuse box, please wire directly to
                                                                                                                                  Ex: GOLF V GTI BWA
                                                                                                                                  (steering wheel on right)                IGN (12V with key in ON position).
                                         Cover
                                                                                                                                  Position= Top Row -
                                                                                                                                             Right Corner
                                                                                                                                                                                                        IGN
                                                                                                                                                                                                    Not as normal
                                                                                                                                             (
                                                                                                                                  Number = 1 SC1)                                                   power source
                                                                                                                                  Capacity = 10A

                                                                            Fuse (included)                                                                         Backside                            Red
             Fuse box                                                                                                           ※If you wish to get power
                                                                                                                                 from a fuse other than the
                                                                                                                                 10A flat mini-fuse, please
    Use a flathead screwdriver or such tool                  Remove the fuse for IGN (12V                                                                                   4p coupler     1p coupler      Cut
                                                                                                                                 purchase separately.
    to remove the cover of the fuse box                      with key on, not as normal power
    found on the side of the panel to the                    source), and insert the fuse power                                                                       = Cut connector (or soldering)
    right of the steering wheel.                             cable.                                   (Front of the fuse box)
                                                             Connect the fuse power cable to
                                                             the 1p coupler from the OBD2
                                                             connector.




     METER INSTALLATION                                                                               Install in an easy-to-view location.                              PART NAMES
    A Install with the adjustable stand                              Fasten using the double-sided tape.                        B
                                                                                                                                Installation with
 Top of the steering               Bottom of the center            Dashboard
                                                                                                                                the cushion tape
 column cover                      console                                                                                                                                                                        1
                                                                                                                                                                                                                  2
                                                                                                                                                                                                                  3

                                                                                                                                    Cushion
                                                                                                                                                    Panel
                                                                                                                                                                       1   Mode Lamp
                                                                                                                                    tape
                                                                                                                                                                      The lamp for the current mode will light up.
                                                                                                                             Wrap the cushion tape
                   Band
                                                                                                                             around the base of the                    2   Switch
                   holder
                                                                                                                             meter and forcibly insert                Use to switch modes and display peak
                                             Stand                      Double-sided                                         into the 60 mm hole in the               readings.
                                                                        tape (included)                    Hexagonal         panel.
                                                                        Clean to remove                    bolt                                                        3   Needle
      Hexagonal bolt               Place of
                                                                        oil & dust                                                                                    Shows the current values and peak
      with washer                installation                                                 After deciding the                                                      readings.
Slightly loosen the screw      Bend the stand to            Fasten using the double-sided     position and angle of
and install the gauge into     securely fit the place       tape. (Clean the surface;         the meter face, fasten
the band holder.               of installation.             removing all oil or dust.)        the hexagonal bolts on
                                                                                              both sides to secure.


                                                                           ※Only the peak value on display will be measured; measurements are not taken for items other than that one on display.
     BASIC OPERATION                                                       ※If after changing modes, the car’s engine is turned off within three seconds, the new setting will not be stored.


Switching Modes                                                                                                                                                    How to Erase Peak Readings
                                                                                        Press the switch                                                           ※Only the peak value on display will be re-set.
        Key ON
1       (Engine start)
                                          Boost                                          for 2 seconds                 Boost
                                          (Real)                                                                       (Real)                                           During the peak display
                START                     BOOST light on                                With no operation              BOOST light blinks
                                                                                         for 5 seconds
                                                                                                                                                                       Press switch                    Press
                                                                                        Press the switch                                                               for 2 seconds                   2 sec
                                          Water Temp                                     for 2 seconds                 Water Temp
2       Opening Demo                      (Real)                                                                       (Real)
                                          WATER light on                                With no operation              WATER light blinks                                  Reset Peak Reading
                                                                                         for 5 seconds
        Each pressing of
3       the switch will
                                                                                        Press the switch                                                                   Return to real display
        change the display                Oil Temp                                                                     Oil Temp
                                                                                         for 2 seconds
                       Press              (Real)                                                                       (Real)
                                                                                        With no operation                                                          ※ Peak readings are reset when the key
                                          Oil °C light on                                                              Oil °C light blinks
                                                                                         for 5 seconds                                                               is turned OFF.



     TROUBLESHOOTING
                                      Trouble                                                                   Possible Causes                                                Possible Solutions
  Does not work with the key ON.                                                          Poor connection of 4p coupler, OBD2 connector or fuse.                 Check the coupler connections or conditions.
                                                                                          If wiring has been direct to power the red wire may have been          Check the red wire connections or conditions.
                                                                                          improperly wired or there is a poor connection.
                                                                                          The unit has been installed into an incompatible car model.            Please check the list of compatible car models.
  The displayed values are different from the standard meter.                             Due to the ECU information received, the displayed values on this product may differ from those of standard or other meters.
  The boost pressure display is different from the standard or other gauge.               This product’s boost meter reads absolute pressure and may differ from a meter using relative pressure.
  With the key in the ON position the boost needles points to a minus reading.            The sensor for absolute pressure is subtracting for barometric pressure and hence the display shows minus.
                                                                                          (EX: Elevation of 700 meters = minus 8Kpa)
  Upon starting up, the unit will start in the newly changed mode.                        Because after changing modes, if the car’s engine is turned off within three seconds, the new setting will not be
                                                                                          stored, make sure to wait at least three seconds before turning the engine off.
  With the key in the ON position, the oil temperature display shows a minus reading.     This is a normal data operation for your car and is not a problem.



                                 PIVOT CORPORATION                                87-3, Shimookada Okada, Matsumoto-shi, Nagano, 390-0313 Japan                    TEL0263-46-5901            h ttp ://pivotjp.com/

				
DOCUMENT INFO