SDS FX Zing by goodbaby

VIEWS: 2 PAGES: 3

									                                PRODUCT INFORMATION

                        Product: FX Zing –Tintable -Interior only.
Product Description:
FX Zing is an interior, water based, tintable, sparkle finish. FX Zing is a hardwearing
and washable liquid paste, especially manufactured for producing a variety of creative
finishes with sponge, brush, roller or spray.

Features:                                Benefits:
Water based                              Easy spreading
Attractive finish                        Easy clean up
Washable                                 Ease of application
Tintable                                 Unlimited colour range
……………………………………………………………………………………………………………….
Uses.
FX Zing produces a variety of special effects on all sealed or chosen acrylic, base coat,
colours on interior surfaces such as plaster, plasterboard, iron, cement, trim, doors,
furniture and timber.
………………………………………………………………………….
Surface Preparation.
All surfaces must be thoroughly cleaned and free of all loose dirt, dust, grease, loose or
flaking paint, and loose surface plaster. Efflorescence or mould on masonry or concrete
surfaces must be treated. Flatten gloss surfaces by thoroughly sanding and wipe clean
with a damp cloth. Then apply FX Primer sealer undercoat as required.
Best results are achieved when surfaces are properly prepared and smooth.
…………………………………………………………………..
Application.
Stir contents thoroughly before and during use with a broad flat stirrer using an upward
action. Brush/Roller: Tint base coat as close as possible to the chosen FX Zing colour.
A satin acrylic base coat makes application easier. Apply the first coat by roller.
Ensure the roller is very soft and between 12mm & 18mm. The second coat may be
applied by roller or a 100mm brush using a criss-cross motion. It is important to keep a
wet edge at all times. To slow down the drying time for large or complicated areas add
approximately 10% of FX Scumble.
Conventional Spray: Suitable for application by all standard spray equipment. Ensure
the first coat is completely dry before adding next application.
Requires: 2 to 3 coats of Zing.
Approximate Spreading Rate: 14-16 square metres per litre, depending on application
and surface roughness.
Approximate Film thickness: Wet-70 microns. Dry-25 microns
Thinner: not required
Method: sponge, spatula, special rollers, brush, roller, conventional spray.
Drying Times:(at 25c) Touch: 4 Hours. Recoat: 24 hours. Clean up: Water.

                             FX Australia Pty Ltd.
                      2 Clegg Place PRAIRIEWOOD NSW 2176
                          PO Box 201 TATHRA NSW 2550
            Telephone/Fax: 6494 4560. Telephone: 9604 2750. Mobile: 0419 251 837
              Email: sanvito@fxaustralia.com.au - Web: www.fxaustralia.com.au
                         A.C.N 089 071 385 A.B.N. 75 089 071 385
                             FX Australia Pty Ltd
                      Page 1 of 2
                   2 Clegg Place PRAIRIEWOOD NSW 2176
                       PO Box 201 TATHRA NSW 2550
        Telephone/Fax: 6494 4560. Telephone: 9604 2750. Mobile: 0419 251 837
                            A.C.N 089 071 385 A.B.N. 75 089 071 385

Date of Issue: November 2003
…………………………………………………………………………………..
                        PRODUCT IDENTIFICATION.

Product: FX Zing
Not classified as hazardous according to criteria of Worksafe Australia
UN NOS: None allocated D.G.CLASS: Not applicable CAS NO: Mixture
HAZCHEM: Not applicable SUB.RISK: Not applicable
PACK GROUP: Not applicable
Correct Shipping Name: Non-Dangerous Good
Other Names:
Ingredients:
Tradename: FX Zing
Chemical Entity:                            CAS NO:                PROPORTION:
Styrene Acrylic Copolymer                    Mixture               2-30%
Styrene                                     100-42-5               0-0.02%
Biocide                     26172-55-4 2682-20-4 10377-60-3 <0.003%
Propylene Glycol                             57-55-6               <0.1%
Water and minor additives (non Hazardous)                             to 100%
NOTE: Proportion of ingredients are quoted as a general guideline
Physical Description/Properties:
Appearance: White liquid paste
Boiling Point: about 100 Deg C
Vapour Pressure: same as water
Volatile Component:
Specific Gravity:
Flash Point: Not applicable. Dried polymer will burn in general fire.
Flammability Limits: Not applicable
Relative Vapour Density: Heavier than air
Form: Liquid Paste
Other Properties:
Solubility in water; Completely dispersible

HEALTH HAZARD INFORMATION.
Acute Effects:
Swallowed: No data supplied. Polymer not expected to be harmful.
Eye: May be eye irritant. May cause redness or soreness.
Skin: Prolonged or repeated contact with skin may result in irritation or rash.
Inhaled: Excessive exposure to vapours or spray mist can cause irritation to eyes, nose
and throat.
Chronic Effects: Not known
                                      FX Australia Pty Ltd
                         Page 2 of 2
                      2 Clegg Place PRAIRIEWOOD NSW 2176
                          PO Box 201 TATHRA NSW 2550
            Telephone/Fax: 6494 4560. Telephone: 9604 2750. Mobile: 0419 251 837
                         A.C.N 089 071 385 A.B.N. 75 089 071 385
……………………………………………………………………..
First aid:
Swallowed: Seek immediate medical assistance.
Eye: Irrigate with copious quantity of water for 15 minutes. Seek assistance if
symptoms persist.
Skin: Wash with soap and water. Warm water if possible.
Inhaled: Remove victim to fresh air, if vapours or mist have been inhaled. Seek
medical assistance if symptoms persist.
First aid Facilities: Normal industrial first aid facilities including eyewash.
Advice To Doctor: Treat symptomatically.            Toxic Data: Not known.

PRECAUTIONS FOR USE.
Exposure Standards: Exposure standards for atmospheric contaminants in the
occupational environment.
Styrene                TWA 20ppm               85mg/m3
Butly Acrylate         TWA 10ppm               55mg/m3
Biocide                TWA 0.1mg/m3
Product        Not established
Engineering controls: General ventilation is recommended during normal use.
Personal Protection: Rubber gloves, Chemical goggles
Flammability: Product is non-flammable according to Australian Code for Transport
of Dangerous Goods. Dried polymer will burn in a general fire.
Environment: Not known.

SAFE HANDLING INFORMATION.
Storage and transport: Store in cool area to prolong storage life.
Packaging and Labelling:
Size:       1 Litre                4 Litre
Weight: 1.2 KG                     4.2 KG
Spills and Disposal: Wear appropriated protection equipment. Do not contaminate
streams, rivers or watercourses. Do not flush into drains or sewers. Inform local
authorities if liquid enters drains, sewers or streams. Dike and contain spill with sand
or earth. Material can then be left to dry or absorb liquid with sand earth or other
absorbents. Dispose of in accordance with local, state and federal regulations.
Fire/Explosion Hazard: To extinguish fires use carbon dioxide, dry chemical or water. Fire
fighters and others exposed to vapours or products of combustion should wear self-contained
breathing apparatus.
Reactivity Data: Incompatibility: none known
Hazardous decomposition: Product: Under severe thermal degradation, low molecular weight
organic compounds will be formed.

     Emergency Contact numbers between 7.30am & 3.30pm Monday to Friday.
   Office: (02) 64944560- Rep: 0419 251 837- Manufacturing Plant (02)9821 1224

The information contained within is supplied in good faith. No warranty, expressed or implied is given.
Any use of this data and information must be determined by the user to be in accordance with applicable
Government laws and regulations. The information contained in this form is confidential and is
submitted solely for you organisation’s internal use. This document is subject to change without
notification.

								
To top