TOYOTA CAMRY CAMRY HYBRID 2007

Document Sample
 TOYOTA CAMRY CAMRY HYBRID 2007 Powered By Docstoc
					TOYOTA CAMRY/CAMRY HYBRID                            2007 -                       XM SATELLITE RADIO
Preparation
Part Number: PT546-33070                                   NOTE: Part number of this accessory may not be
                                                           the same as the part number shown.
Kit Contents
Item #     Quantity Reqd.   Description                     Nylon Removal Tool
1          1                Receiver cable                  Torque Wrench
2          2                Receiver bracket                Side Cutter
3          1                Antenna
                                                            Special Chemicals              Notes
Hardware Bag Contents-1                                     Cleaner                        3MTM Prep Solvent-70
Item #     Quantity Reqd.   Description
1          5                Cushion tape                   General Applicability
2          12               Lock tie

                                                           Recommended Sequence of Application
Hardware Bag Contents-2                                     Item #    Accessory
Item #     Quantity Reqd.   Description
1          2                Cushion tape                                                                *Mandatory
2          4                Screw (M5 x 8)
3          2                Flanged nut
                                                           Vehicle Service Parts (may be required for reassembly)
                                                            Item #    Quantity Reqd.    Description
                                                            1         2                 Cowl cover clip P/N 90467-
Hardware Bag Contents-3                                                                 09212
Item #     Quantity Reqd.   Description                     2         3                 Frt scuff plate clip P/N 90467-
1          1                Cushion tape                                                A0006
2          9                Sheet tape                      3         3                 Lwr “B” pillar trim clip P/N
3          1                Ground plate                                                90467-A0006
4          1                Antenna template                4         2                 RR scuff plate clip P/N 90467-
                                                                                        A0006
                                                            5         1                 “C” pillar clip P/N 90467-
Additional Items Required For Installation                                              10188
Item #     Quantity Reqd.   Description                     6         4                 “C” pillar clip P/N 90467-
1          1                XM tuner P/N 86180 – 0W030                                  A0006
2                                                           7         7                 Trunk trim clip P/N 90467-
                                                                                        A0006
Conflicts                                                   8         2                 Luggage trim clip P/N 90467-
                                                                                        08186-CO
Fixed Rear Seat
Recommended Tools
                                                           Legend
Personal & Vehicle            Notes
Protection                                                        STOP: Damage to the vehicle may occur. Do not
Safety Goggles                                                    proceed until process has been complied with.
Seat cover                                                        OPERATOR SAFETY: Use caution to avoid risk of
Floor Protectors                                                  injury.
                                                                  CAUTION: A process that must be carefully observed
Special Tools                  Notes                              in order to reduce the risk of damage to the
                                                                  accessory/vehicle and to ensure a quality installation.
None
                                                                  TOOLS & EQUIPMENT: Used in Figures calls out the
                                                                  specific tools and equipment recommended for this
Installation Tools            Notes                               process.
Ratchet                                                           REVISION MARK: This mark highlights a change in
Extension                                                         installation with respect to previous issue.
Socket                         10mm, 12mm
Phillips Screwdriver



Issue: B    05/18/06                             Page 1 of 15 pages
TOYOTA CAMRY/CAMRY HYBRID                         2007 -              XM SATELLITE RADIO
Preparation




                          Item #                   Parts Name            Qty
                             1         RECEIVER ASSY, Radio               1
                                   A   RECEIVER CABLE                     1

                                   B   CUSHION TAPE                       5
                      2            C   LOCK TIE                           12
                                   A   RECEIVER BRACKET                   2

                                   B   FLANGED NUT                        2
                                   C   SCREW (M5 x 8)                     4
                      3
                                   A   ANTENNA                            1
                                   B   TEMPLATE (to locate antenna)       1
                                   C   CUSHION TAPE                       1
                                   D   SHEET TAPE                         9
                      4            E   GROUND PLATE                       1




Issue: B   05/18/06                          Page 2 of 15 pages
TOYOTA CAMRY/CAMRY HYBRID                                    2007 -                     XM SATELLITE RADIO
Procedure
Care must be taken when installing this accessory to ensure damage does not occur to the vehicle. The installation of this
accessory should follow approved guidelines to ensure a quality installation.

These guidelines can be found in the "Accessory Installation Practices" document.

This document covers such items as:-
    • Vehicle Protection (use of covers and blankets, cleaning chemicals, etc.).
    • Safety (eye protection, rechecking torque procedure, etc.).
    • Vehicle Disassembly/Reassembly (panel removal, part storage, etc.).
    • Electrical Component Disassembly/Reassembly (battery disconnection, connector removal, etc.).

Please see your Toyota dealer for a copy of this document.


                                                                1. Vehicle Protection.
                                                                    (a) Take note of the negative battery cable
     10 mm Socket                Negative battery cable                 installation position, as this will need to be
                                                                        re-installed in the same position after
                                                                        installation completion.
                                                                    For Camry Hybrid go to step 1.(b).
                                                                    (b) Remove the negative (–) battery cable.
                                                                        (Fig. 1-1)
Fig. 1-1                                                              NOTE: Protect the fender before removing the
                                                                      battery cable.
      Clips x (2)
                                                                      NOTE: Be careful not to touch the positive
                                                                      terminal.

                                                                FOR CAMRY HYBRID (steps 1(b) – 1(e))
                                                                    (c) Open trunk
                                                                    (d) Locate battery access Panel
                                                                    (e) By pressing the 2 clips remove the battery
Fig. 1-2
                                                                        access panel (Fig. 1-2)
                                                                    (f) Remove the negative (–) battery cable.
                                 Negative battery cable                 (Fig. 1-3)




                                       10 mm Socket
 Fig. 1-3



 Issue: B   05/18/06                                  Page 3 of 15 pages
TOYOTA CAMRY/CAMRY HYBRID                                   2007 -                    XM SATELLITE RADIO
Procedure



                                                                 2. Disassembly of Vehicle.

   Nut                                                               (a) Remove the trunk mat and accessories.
                                                                     (b) Move spare tire cover.
                                                                         (1) Remove nut. (Fig. 2-1)
                                                                         (2) Slide cover forward to allow trunk trim to
Fig. 2-1                                                                     be removed.

                                                                 FOR CAMRY HYBRID (step 2(c))
                                                                     (c) Remove the trunk plastic trim cover.
                                                                         (1) Remove plastic nut. (Fig 2-2)
                                          Plastic nut                    (2) Remove cover panel. (Fig 2-2)




Fig. 2-2



               Hooks (Phillips) x 2                                  (d) Remove the trunk plastic trim piece.
                                                                         (Fig. 2-3)
                        Clips x 4
                                                                         (1) Remove plastic hooks with a Phillips
                                                                             screwdriver.
                                                                         (2) Detach clips and pull upward on trim to
                                           Clips x 3                         remove.
                                    Nylon Removal Tool
Fig. 2-3                            Phillips Screwdriver
                                                                     (e) Remove the trim cover in the luggage
                                      Nylon Removal Tool                 compartment. (Fig. 2-4)
                                                                         (1) Remove screw hook by turning counter
                                                                             clockwise.

 Clips x 2                                                               (2) Remove plastic clips.
                                                                     FOR CAMRY HYBRID (step 2. (f) to 2. (g)
                             Screw hook
                                                                     (f) Remove two (2) plastic clips only, No screw
 Fig. 2-4
                                                                         hook.
                                                                     (g) Remove luggage compartment trim cover.
Issue: B     05/18/06                                   Page 4 of 15 pages
TOYOTA CAMRY/CAMRY HYBRID                          2007 -                    XM SATELLITE RADIO
Procedure
                                                          (h) Remove the rear seat cushion.
                                                               (1) Lift rear seat cushion straight up
                                                                   disengaging clips located beneath.
                                                                   (Fig. 2-5)
     Clips
                                                               (2) Push female seat belt receptacles through
                                                                   seat cushion holes.

                               Rear seat cushion
 Fig. 2-5

                                                      FOR VEHICLES WITH FOLD DOWN REAR
                                                      SEAT (Step (2(i).
      12 mm socket
             Right Rear Seat                              (i) Remove the passenger’s side rear seat
             Shoulder                                         shoulder.
                                                               (1) Use 12 mm socket and extension to
                                                                   remove the bolt located on rear right seat
                                                                   shoulder (Fig. 2-6). Torque on
   Bolt w/washer
                                                                   reassembly 18 N-m [13 lbf-ft]
 Fig. 2-6
                                                               (2) Slide the rear seat shoulder up to remove.
                                                      FOR VEHICLES WITH RECLINING REAR
                                                      SEAT (Steps 2. (j) and 2 (k))
                                                            NOTE: Be sure rear seat is in the fully reclined
                                                            position.
                                                          (j) Remove the passenger’s side rear seat.
                                                               (1) Remove passenger side rear seat head
                                                                   rest.

 Fig. 2-7                                                      (2) Separate the rear seat belt.
                                                               (3) Disengage the three (3) clamps and then
                                                                   separate the cover. (Fig. 2-7)
                                                               (4) Remove the two (2) covers, two (2) bolts
                                                                   and two (2) nuts and separate rear seat
                                                                   back assembly RH.
                                                               (5) Use 12 mm socket and extension to
                                                                   remove the bolts shown. (Fig. 2-8).
                                                                   Torque on reassembly to 18 N-m
 Fig. 2-8                                                          [13 lbf-ft])


Issue: B     05/18/06                        Page 5 of 15 pages
TOYOTA CAMRY/CAMRY HYBRID                          2007 -                  XM SATELLITE RADIO
Procedure
                                                          (k) Remove reclining remote control lever sub-
                                                              assembly.
                                                              (1) Remove the bolt.
                                                              (2) Disengage the two (2) clips and the claw
                                                                  and then separate the reclining remote
                                                                  control lever sub-assembly. (Fig. 2-9)
                                                              (3) Separate the rear seat reclining control
  Fig. 2-9
                                                                  cable and remove the reclining remote
                                                                  control lever sub-assembly. (Fig. 2-10)




 Fig. 2-10


                                                          (l) Remove the passenger side C pillar trim.

 Nylon
                                                              (1) Partially remove the body weather strip.
 Removal
 Tool                                                         (2) Use the nylon removal tool to disengage
                                                                  clips. (Fig. 2-11)
                                                              (3) Remove C pillar trim.


 Fig. 2-11

                                                          (m) Remove the passenger’s side rear scuff plate.
    Right rear scuff plate.                                   (1) Use nylon removal tool to disengage
                                                                  clips on rear right scuff plate. (Fig. 2-12)




                                       Clips x2

 Fig. 2-12                    Nylon Removal Tool




Issue: B     05/18/06                        Page 6 of 15 pages
TOYOTA CAMRY/CAMRY HYBRID                                       2007 -                    XM SATELLITE RADIO
Procedure

       Nylon Removal Tool
                                        Nut   Cowl side trim             (n) Remove the front passenger side scuff plate
                                                                             and cowl side trim. (Fig. 2-13)
                                                                             (1) Use nylon removal tool to disengage
                                                                                 clips on front right scuff plate.
Clips x3                                                                     (2) Remove front scuff plate.

 Fig. 2-13
                                        Front scuff plate                    (3) Remove right cowl side trim nut by
                                                                                 turning counter clockwise.
                                                                             (4) Remove cowl side trim.
  Pull out on sides
  to release 2 clips

                                                                         (o) Remove the Passenger’s Side B Pillar Cover.
                                                                             (1) Partially remove the door weather strip.
    Clips x4
                                                                             (2) Use nylon removal tool to disengage
                                                                                 clips on right B pillar cover. (Fig. 2-14)
 Fig. 2-14                             Nylon Removal Tool
                                                                             (3) Remove the B pillar cover. (Fig. 2-14)

                                       Nylon Removal Tool
  Clips x 5



                                                                         (p) Disassemble Center Cluster and Radio.
                                                                             (1) Use nylon removal tool to disengage
                                                                                 clips and remove air vent. Disconnect any
Clips x 2
                                                                                 electrical connectors. (Fig 2-15)
 Fig. 2-15



      Nylon Removal Tool

                       Shifter cover

 Console                                                                     (2) Remove side trim pieces. (Fig 2-16)
 cover
                                                                             (3) Remove shifter cover. (Fig. 2-16)
                                                                             (4) Use nylon removal tool to remove center
                                                                                 console cover. (Fig. 2-16)

                                               Trim pieces
Fig. 2-16


Issue: B      05/18/06                                      Page 7 of 15 pages
TOYOTA CAMRY/CAMRY HYBRID           2007 -                   XM SATELLITE RADIO
Procedure


                                                (5) Remove the 2 screws securing the center
                                                    console storage compartment. (Fig. 2-17)
                           Screws               (6) Pull in the direction shown to remove the
                           (x 2)
                                                    storage compartment. (Fig. 2-17)
                                                (7) Disconnect the electrical connectors.


 Fig. 2-17
                                            (q) Remove the Radio/Combo.
                                                (1) Use 10 mm socket and extension to
     10 mm socket                                   remove bolts located on combo.
                                                    (Fig. 2-18)
Bolts x 4




 Fig. 2-18
                                                (2) Remove combo and place onto box.
                                                    (Fig. 2-19)
                                             NOTE: Do not disconnect the electrical
                                             connections. Place a protective cover between
                                             the box and center console.




 Fig. 2-19


                                            (r) Remove the Under Dash Cover.
      Nylon Removal Tool
                                                (1) Remove the under dash cover. Use nylon
                                                    removal tool to disengage the three clips
                                                    on under dash cover. (Fig. 2-20)




  Fig. 2-20



Issue: B     05/18/06          Page 8 of 15 pages
TOYOTA CAMRY/CAMRY HYBRID                                       2007 -                    XM SATELLITE RADIO
Procedure

                           Phillips screw x3
                                                                         (s) Remove the entire glove box assembly.
                                                                             (Fig. 2-21)
                                                                             (1) Open the glove box.
                                                                             (2) Remove the bolt and screws that secure
                                        Bolt                                     the glove box.
    Phillips screw
                                     Nylon Removal Tool
                                     Phillips Screwdriver                    (3) Pull to disengage clips and remove.
  Fig. 2-21                          10mm socket
                                                                                 Disconnect any electrical connections.



                                                                     3. Cable Routing and Installation
                          Foam
                                                                         (a) Install and route the tuner cable from the
                                                                             center cluster and along the front support bar.
                                                                             (Fig. 3-1)

                                               Lock tie A                (b) Provide sufficient cable slack to connect to
                                                                             the tuner, and then secure the cable to the
Fig. 3-1                                                                     existing wire harness with lock tie. Cut
                                                                             excess off lock tie. Connect wire harness to
                                                                             head unit.


              Lock tie A x 6                                             (c) Using lock ties attach to existing W/H. Trim
                                                                             lock tie excess. (Fig. 3-2)
                                                                         (d) Route to the existing clamps. (Fig. 3-2)



Fig. 3-2




                                       Route
                                       underneath                        (e) Route tuner cable as shown and secure with
                                       existing harness
                                                                             lock ties. Trim lock tie excess.(Fig. 3-3)




                   Lock tie x 4          Side Cutter
 Fig. 3-3



Issue: B    05/18/06                                        Page 9 of 15 pages
TOYOTA CAMRY/CAMRY HYBRID                                   2007 -                   XM SATELLITE RADIO
Procedure


      Side Cutter                                                   (f) Route the cable as shown and secure with
                        Lock tie                                        lock tie. Trim lock tie excess. (Fig. 3-4)
                                                                    (g) Route the tuner cable under the rear
                                                                        passenger seat and secure with cushion tape.
                                                                        (Fig. 3-5)
                                                                    NOTE: Clean the area for the cushion tape with
                                                                    the approved cleaner.
 Fig. 3-4


 Front                                        Hole to
                                              Trunk

   Receiver cable




                                                                4. Antenna Installation.
 Fig. 3-5                               Cushion tape
                                                                    (a) Clean the template mounting area.
                                                                    (b) Position the antenna mounting template to
  Front                                                                 align to the beveled edge at the rear of the
                                  Template
                                                                        package tray. (Fig. 4-1)




  Align template edge with rear
  package tray edge                                                 (c) Remove the release paper from the back of
 Fig. 4-1
                                                                        antenna, and then attach to the center of the
                                                                        ground plate.
                                                                    (d) Remove the release paper from the back of
                                                                        the ground plate and place the ground plate
                                                                        into the template. (Fig. 4-2)
                                                                     NOTE: Align the ground plate with the
                                                                     template as shown and install it carefully. Once
                                                                     attached, the ground plate cannot be easily
                                                                     removed.
  Fig. 4-2



Issue: B     05/18/06                                  Page 10 of 15 pages
TOYOTA CAMRY/CAMRY HYBRID                                    2007 -                  XM SATELLITE RADIO
Procedure
      Panel Removal Tool
                                                                     (e) Remove and discard the mounting template.
                                                                     (f) Secure the antenna cable between the rear
                                                                         windshield and rear package tray by pressing
                                                                         the cable cushions with a nylon removal tool.
                                                                         (Fig. 4-3)


                           Cushions on antenna cable.
 Fig. 4-3
                                                                     (g) Route the antenna cable as shown and secure
                                                                         with sheet tape. (Fig. 4-4)

   Sheet tape x 2


    Front




 Fig. 4-4


                                                                     (h) Route the antenna cable as shown and secure
                                                                         with sheet tape. (Fig. 4-5)



 Sheet tape



  Fig. 4-5


                                                                     (i) Route the antenna cable as shown and secure
                                                                         with sheet tape. (Fig. 4-6)

 Sheet tape


  Front


  Fig. 4-6


Issue: B     05/18/06                                   Page 11 of 15 pages
TOYOTA CAMRY/CAMRY HYBRID                            2007 -                  XM SATELLITE RADIO
Procedure
                                                            (j) Place the antenna cushion tape along the
                 Sheet tape                                     upper edge of the hole leading to the trunk.
                                                                (Fig. 4-7)
                                                            (k) Route the antenna cable as shown and secure
                                                                with sheet tape. (Fig. 4-7)




                                Cushion tape
  Fig. 4-7
                                                            (l) Route the antenna cable and the receiver
                                                                cable as shown and secure with cushion tape.
                                                                (Fig. 4-8)
     Front




    Cushion tape



  Fig. 4-8
                                                        5. Tuner Installation.
                                                            (a) Install the mounting brackets onto the tuner.
                              Phillips Screwdriver
                                                                (Fig. 5-1)
                                                              NOTE: The bracket shown on the right will not
                                                              use the locating dimples on the bracket.
                                       Bolts x 4


                                                            For Camry Hybrid – go to step 5. (d)

  Fig. 5-1


                                            Front           (b) Install the tuner on the right side of the
                                                                luggage compartment using nuts. Orient the
                                                                tuner so the tuner connectors can be accessed
                                                                from the rear as shown. (Fig. 5-2)

 Nuts x 2                                                     NOTE: Do not pinch the sunroof drain tube.



 Fig. 5-2                          10 mm Socket



Issue: B     05/18/06                          Page 12 of 15 pages
TOYOTA CAMRY/CAMRY HYBRID                      2007 -                  XM SATELLITE RADIO
Procedure
                                                      (c) Connect the receiver cable and the antenna
                                                          cable. Finish routing the antenna cable as
                                                          shown. (Fig. 5-3)




                              Sheet Tape x 2
 Fig. 5-3
                                                      FOR CAMRY HYBRID (steps 5(d) and 5(e))

                 Nuts x (2)                           (d) Install the tuner on the right side of the
                                                          luggage compartment using nuts. Orient the
                                                          tuner so the tuner connectors can be accessed
                                                          from the rear as shown. (Fig. 5-4)
                                                        NOTE: Do not pinch the sunroof drain tube.
                                                      (e) Connect the receiver cable and the antenna
                                                          cable. Finish routing the antenna cable as
  Fig. 5-4                                                shown. (Fig. 5-4)


                                                      (f) If there is excessive slack, bundle and secure
                                                          the excess cable to the bulkhead using
                                                          cushion tape. (Fig. 5-5)

                                                  6. Verify SDARS functionality.
Cushion tape                                          (a) Install the short pin fuse to function check all
                                                          electrical items.

 Fig. 5-5                                         7. Complete the reassembly of the vehicle:
                                                      (a) Reconnect any disconnected connectors.
                                                      (b) Verify the panels fit together properly with
                                                          no uneven gaps between them.
                                                      (c) Torque the reclining rear seat to (18 N-m)
                                                          (13 lbf-ft).




Issue: B     05/18/06                    Page 13 of 15 pages
TOYOTA CAMRY/CAMRY HYBRID                        2007 -                 XM SATELLITE RADIO
Procedure
                                                    8. Completing the Installation.
                                                       (a) Reconnect the vehicle’s negative battery
10 mm Socket
Torque Wrench                                              cable. (Fig. 8-1)
                                 Negative
                                 battery cable
                                                       FOR CAMRY HYBRID (Fig. 8-2)
                                                           (1) Position the negative terminal at the
                                                               original factory position.
                                                           (2) Tighten the nut with 4.1 N-m (36 lbf-in)
 Fig. 8-1                                                      of torque.
                                                           (3) Be careful not to touch the positive
                                                               battery terminal.
                       Negative battery cable
                                                       (b) Clean up and remove any trash.
                                                       (c) FOR CAMRY HYBRID replace the battery
                                                           access panel.
                                                       (d) Place the owner "XM Satellite Radio"
                                                           brochure in the glove box.
                            10 mm Socket
 Fig. 8-2
                            Torque wrench




Issue: B    05/18/06                     Page 14 of 15 pages
TOYOTA CAMRY/CAMRY HYBRID                                2007 -                       XM SATELLITE RADIO
Checklist - these points MUST be checked to ensure a quality installation.
           Check:                                                         Look For:
Accessory Function Checks

           Verify the proper operation of the satellite                   Refer to the receiver assembly and radio
           radio tuner.                                                   owner’s manuals.

           Verify the proper operation of the receiver                    Refer to the receiver assembly and radio
           assembly and radio.                                            owner’s manuals



Vehicle Function Checks

           Verify the proper operation of the hazard                      Hazard switch operates properly.
           switch.

           Verify the rear passenger seat back is in the                  Rear passenger seat back positioning.
           upright position and the latch secured.

           Verify the proper operation of the air                         Cold air emits from vents properly.
           conditioning system.

           Verify the proper operation of the multi-                      Multi-information display lights up and is
           information displays. (Clock, Temp., and                       readable.
           MPG meter)

           Verify the proper operation of the L & R                       L & R seats heat up properly.
           seat heater switch.

           Verify the proper operation of the 12V                         Power is provided through the 12V outlet
           outlet switch.                                                 switch properly.

           Verify the proper operation of the rear seat                   Rear seat reclines and returns to upright
           reclining feature. (where applicable)                          position.




Issue: B     05/18/06                               Page 15 of 15 pages

				
DOCUMENT INFO