Docstoc

Wireless Bass Shaker Assembly

Document Sample
Wireless Bass Shaker Assembly Powered By Docstoc
					Wireless Bass Shaker Assembly
A minimum five-channel home theater amplifier with a sub-woofer output is required to                              THE MANUFACTURER DOES NOT ACCEPT LIABILITY FOR ANY DAMAGE/
operate the Wireless Bass Shaker system.                                                                           FAILURE TO ANY ELECTRONIC COMPONENTS DUE TO FAILURE TO
The Bass Shaker unit housed in the seat back has a nominal impedance of 4 ohms.                                         COMPLY WITH THE WIRING INSTRUCTIONS PROVIDED.
The Shaker Amplifier has a 16-gauge speaker wire attached to connect to the Bass Shakers.                           1. Find the line level subwoofer output (LFE) for the subwoofer channel on the rear panel of
The Shaker Amplifier is housed in the back of the seat with the RF receiver. Recommended                               your A/V Receiver and disconnect the cable going to your powered subwoofer. Replace
amplifier wattage (per seat): 50 watts. Use of higher wattage per seat could potentially                               with the Y Cable (male to double female). Connect the male end to the A/V Receiver.
damage the Bass Shaker. The Shaker Amplifier's output can only be used to connect
other 50 watt amps. Connecting other electronics to the output could result in damage.                             2. Connect one female end of the Y Cable to your Powered Subwoofer.

The wireless transmitter kit should include one RF transmitter, one Y Cable, one cable with                        3. Connect the other female end of the Y Cable to the input on the RF Transmitter.
male ends and one transformer for the transmitter.                                                                    Connect RF Transmitter wall plug to power outlet.

The Bass Shakers are powered by the Shaker Amplifier and receive the same signal as your                            4. Connect the corresponding speaker wire of the Shaker Amplifier to the Bass Shakers. The
powered subwoofer. The Shaker Amplifier and RF Receiver will only receive a signal from the                            Shaker Amplifier comes installed from the factory, it is located at the bottom rear base of
RF Transmitter that is connected to a subwoofer output or a low frequency effect channel (LFE).                       the seat.
                                                                                                                   5. Connect the Intensity Toggle Switch cable to the Shaker Amplifier.
Inside              Connect to Bass Shakers
Seat                                                                                                               6. Connect the Shaker Amplifier wall plug to power outlet.
Back
Setup              Red Terminal                           Black Terminal                                           7. Set the intensity level of the Bass Shakers by adjusting the Intensity Toggle Switch
                                                                                                                     and volume controls of your home stereo.

                                                                                                                                                                      TROUBLE SHOOTING
                                                                                                                                                                         No Vibration from Bass Shakers
                                                                                Intensity
                                                                                                                                                                      SOLUTIONS
                                                                                Toggle
                                                                                Switch                                                                                1. Dip switches on RF Transmitter and RF
                                                                                                                             Home Stereo Setup                           Receiver must match.
                                                                                                                                                                      2. Check that the RF Transmitter is
                                                                                                                                                 A/V Receiver            plugged into wall and powered on
                                                                                                           Powered                                                       (LED will light up). Check that the Y
                                                                                                                                                  (Amplifier)
Inside                                               Connect                                               Sub Input                                                     Cable is plugged into RF Transmitter.
Seat
Setup
                                                     to Amp                                                                                       Line level
                                                                                                                                    Y Cable                           3. Check that Shaker Amplifier is plugged
                    Shaker Amplifier                                                                                                             Subwoofer               into wall and powered on.
                                                                   RF Receiver                           RF Transmitter                          Output (LFE)
                                                                                                                                                                      4. Ensure Bass Shakers are securely
                               Receiver Input
                                                                                                                                                                         connected to Shaker Amplifier in chair.
         Shaker                                                    Dip Switch    LED                      Dip Switch   LED
                  RCA Out RCA In           Volume                                           Wireless
                                                                                                                                                                      5. Check that the Intensity Toggle switch
                                                                                            Signal                                                                       is plugged into Shaker Amplifier in
                                                                                                                                                                         chair. Turn up Intensity Toggle switch
                                                                                                                                                                         if required.
                                                Power and Signal                                                                                                      6. Ensure RF Receiver is connected to
                                                                                                       Transformer
                                                                                                                                                                         Shaker Amplifier in chair seat (LED will
              to Wall Plug                                                                             to Wall Plug
                                                                                                                                                                         light up).

                                                         NO USER SERVICEABLE PARTS
Seating Assembly
P U T T I N G S E AT S T O G E T H E R

STEP 1                                               STEP 2                                                  STEP 3                                               STEP 4
Attach all connector pins into threaded              Line up back of arm with back of seat                   Attach next arm to seat. (This arm will              Kneel down to get at eye level with the mecha-
plates. Bring arm to seat.                           frame and push together. This will create a             attach to the seat the same as step 2.)              nism posts while holding the chair back to have
                                                     tight pressure fit (arm will lock in place).                                                                  metal sleeves exposed to you. Line up sleeves with
                                                                                                                                                                  mechanism posts and slide sleeves onto the posts.
                                                                                                                                                                  Push down firmly to secure. Repeat step 4 as
                                                                                                                                                                  needed for your configuration.




                                                                                                             I M P O R TA N T N O T E S :
                                                                                                             ARM WILL BE FLUSH WITH BACK WHEN TOGETHER.
I M P O R TA N T N O T E S :                         I M P O R TA N T N O T E S :
CONNECTORS ALWAYS HAVE PINS ON THE RIGHT HAND        ATTACH ARM STARTING WITH THE RIGHT HAND FACING          Repeat steps 2 & 3 until you have completed
FACING SIDE (RHF) AND SLOTTED CONNECTORS ON THE      SIDE (RHF). ENSURE THAT ALL THE CONNECTING POINTS ARE   your configuration. For seating with Bass
LEFT HAND FACING SIDE (LHF). LEAVE BACKS OFF UNTIL   TIGHT LEAVING NO GAPS BETWEEN SEAT AND ARM.
ARMS AND WEDGES HAVE BEEN ATTACHED TO SEATS.                                                                 Shaker options, refer to Bass Shaker
                                                                                                             Assembly before proceeding to step 4.


TA K I N G S E AT S A PA R T

STEP 1                                                   STEP 2                                                                              STEP 4
Lift back sleeves from mechanism posts.                  Stand at the back of the assembled unit. First push on the back                     Repeat steps 2 & 3 until you have reached the final arm on the
Pull up firmly to release. NOTE: For seating              of the left hand facing end arm until unlocked. Then push on                        right hand facing side (RHF). This arm will release in the opposite
with Bass shaker option, lay seat back                   the back of the seat to unlock it from the universal arm/wedge.                     direction as indicated.
on seat, and disconnect wiring. Repeat                   Continue this sequence till the seat attached to the right hand
step 1 as needed for your configuration.                  facing end arm. Arrows show direction of release.




                                                         STEP 3
                                                         Arm will unlock when pushed in directions as indicated.


                                                                                                                                              WARNING:
                                                                                                                                              Do not allow children to play on this mechanized furniture or operate this mechanism.
                                                                                                                                              Leg rest folds down on closing, so a child could possibly be injured. Always leave in an
                                                                                                                                              upright and closed position. Keep hands and feet clear of mechanism. Do not operate
                                                                                                                                              mechanism with fingers between the seat cushions and/or arms.
                                                                                                                                              Only the occupant should operate the mechanism.

				
DOCUMENT INFO
Shared By:
Categories:
Stats:
views:122
posted:4/2/2010
language:English
pages:2