STRONG SRT4651X HOW TO RE-TUNE YOUR EXISTING SATELLITE DISH TO THE

Document Sample
STRONG SRT4651X HOW TO RE-TUNE YOUR EXISTING SATELLITE DISH TO THE Powered By Docstoc
					                                              STRONG SRT4651X

  HOW TO RE-TUNE YOUR EXISTING SATELLITE DISH TO THE OPTUS D2 AND
                 RECEIVE THE CHRISTIAN CHANNELS
  If you have a Foxtel or Austar Dish installed on your property follow these steps to re-tune your dish.
  The satellite we are looking for is the Optus D2 satellite at 152’0 E

  Connect your receiver to your TV by using the RCA yellow/red/white cable and the Black RF Cable to the
  wall plate and to the back of the receiver where it is labelled “LNB Input”

  Turn on your TV and ensure that the AV channel which you have connected your receiver to is displaying.
  Turn on your satellite receiver by switching the main switch on the left of the back of the receiver. Numbers
  should now display on the front of the receiver. If the receiver is displaying the time on the front, this means
  the receiver is on standby. If it is on standby, turn on the receiver by pressing the power button on the
  remote.

  Now you will need to check what LNB type your dish is using. The LNB is the small device on the front of
  the dish. On the LNB there will be a sticker. This sticker should display LNB frequency numbers either L.O
  11300 or L.O 10700. Remember which number is displayed as you will need it later.
  If you are unable to identify a number on the sticker, you will need to try both possibilities later.

  Now that you have the LNB Frequency number (the 5 digit numbers) go back to your receiver and by using
  your satellite remote follow these steps;


STEP 1 – SETTING UP THE LNB

  A. Turn the receiver on from the main switch at the back left of the receiver.
  B. When the receiver is on you will see on your screen (SELECT YOUR LANGUAGE) Select English and press the
     OK button on the remote.
  C. Now press the MENU button on the remote.
  D. By using the UP and DOWN button, scroll up or down and select INSTALLATION and press the OK button. The
     receiver will request a password. Enter 0000
  E. Next scroll UP or DOWN and highlight DISH SETTINGS and press the OK button
  F. Now you should be in DISH SETTINGS. Next Scroll DOWN to SATELLITE NAME and press OK.
  G. Next scroll left or right and select OPTUS B3/Ku and press the OK button.
  H. Next scroll down to LNB POWER and press OK button
  I. Next scroll up or down and select SINGLE and press OK button
  J. Next scroll up or down and select LNB TYPE and press OK button.
  K. Next scroll up or down and select 10.700 and press OK button.
  L. Next press the exit button and the receiver will display a message “Settings were changed DO YOU WANT TO
     SAVE? Highlight YES in yellow and press the OK button

STEP 2 - SETTING UP RECEIVER FOR TUNING

  A.   From the MAIN MENU select INSTALLATION and press the OK button.
  B.   The receiver will request a password. Enter 0000
  C.   Next highlight MANUAL SCAN and press the OK button
  D.   Next highlight SATELLITE and scroll left or right and select OPTUS B3/KU
  E.   Next highlight FREQUENCY and press the GREEN button on the remote
  F.   Next enter 12706 using the numbers on the remote
  G.   Next highlight SYMBOL RATE and enter 22500 using the numbers on the remote
  H.   Next highlight POLARIZATION and scroll left or right using the remote and select V

                                                                                                          Page 1
Now it’s time to tune your Satellite dish

Make sure you have the correct spanner or shifter to undo the four nuts on the back of the dish. At this stage,
you will need a person to assist you. Their job is to watch the Signal Strength and Quality bars.




Slowly undo the four nuts, little by little, and move the dish slightly to the left, but not too fast, until your
assistant notices the quality bars will started to increase in percentage. If at this point there is no signal coming
through on the strength or quality bars, the LNB type may be incorrect. Please go back to DISH SETTING and
change the LNB FREQ to the alternate option.


Take note of where the quality bar is on its highest percentage, and if your assistant notices it start to drop,
stop and move the dish back to the right slowly, until you find the maximum strength quality signal. Once
you’ve reached your maximum percentage, evenly tighten the nuts. Be aware that over-tightening one of the
nuts may throw the dish out of alignment. If the quality bar drops while you are tightening the nuts, correct it by
tightening the nut opposite, or the nut above.

Now you have adjusted the horizontal orientation of the satellite, you now need to adjust the vertical orientation




                                                                                                             Page 2
To adjust the vertical orientation, adjust the side nuts as shown in picture. Once you’ve undone the nuts, tilt the
satellite dish up and down until the quality bar reaches its maximum. Once it’s reached the maximum, carefully
tighten the nuts, without losing the dishes position.




The final step in fine tuning the dish is to re-tune the LNB. To achieve this, undo the two screws and turn the
LNB until the quality bar reaches its maximum percentage level.




Once you’ve found your maximum quality strength, secure the LNB.

Now you may scan for channels.

STEP 3 – SCANNING FOR CHANNELS

   A.   Now that your dish is tune press the EXIT button on the remote to exit MANUAL SCAN
   B.   Next scroll down and highlight BLIND SCAN and press the OK button
   C.   Next scroll up or down in the list of satellite and highlight OPTUS B3/KU and press the OK button on the remote
   D.   Next scroll to the right and highlight MODE and by scrolling left or right select FREE
   E.   Next scroll down and highlight PRESS OK
   F.   Next press the OK button and the receiver will begin searching for the new frequency’s and channels
   G.   Once the scan has finished press the EXIT button once

Once you have finish STEP 3 please follow STEP 4.



                                                                                                                Page 3
Please note that the receiver will scan all the channels on that Frequency so the Christian Channels will not be grouped
and will be mixed between the other foreign channels.

If you wish to delete any of the foreign channels, Please follow STEP 4.

STEP 4 - Deleting unwanted Channels
    A. From the MAIN MENU scroll left and highlight CHANNELS and press the OK button
    B. The receiver will request a password. Enter 9402 or if that does not work try 0000
    C. Next highlight DELETE CHANNELS and press the OK button
    D. Next scroll through the channel list and press the OK button on all the unwanted channels in the list and all the
       unwanted channels should have an X in front of them.
    E. When you are finished press the EXIT button on the remote and the receiver will display a message “Warning!
       Do you want to delete” Highlight YES in yellow and press the OK button and the receiver will exit out of the
       delete channel menu.

If you would like to group your favourite’s channels together in the Channel list please follow STEP 5.

STEP 5 - Grouping your favourite channels together in the channel list
    A. From the MAIN MENU scroll UP highlight MOVE CHANNELS and press the OK button.
    B. Next scroll through the channel list and press the OK button on the channel that you would like to move. Now
       scroll UP or DOWN and move the channel to where you would like it to appear in the list and press OK. Continue
       this with the various channels until you are satisfied with the list.
    C. Once you are finished press the EXIT button on the remote and the receiver will display a message “Settings
       were changed DO YOU WANT TO SAVE? Highlight YES in yellow and press the OK button.
    D. Now press the EXIT button twice

Please make sure all of the channels are working and are in your order of preference.


Now there should be 11 Christian Channels in the list If you like you can go back to the MAIN MENU and go to
CHANNELS to move or delete channels. Please see your user’s Manual for more info.

Please make sure everything is tight and locked off.

OPTUS B3 CHRISTIAN CHANNELS

    1.    3ABN
    2.    The Hope Channel
    3.    EWTN
    4.    The Church Channel
    5.    Daystar TV
    6.    Trinity
    7.    JCTV
    8.    The God Channel
    9.    Smile of a Child
    10.    Inspiration TV
    11.   AON




                                                                                                                  Page 4

				
DOCUMENT INFO
Shared By:
Categories:
Stats:
views:698
posted:3/31/2010
language:English
pages:4
Description: STRONG SRT4651X HOW TO RE-TUNE YOUR EXISTING SATELLITE DISH TO THE