5m high portable flag ideal for indoor or outdoor events, promotions or exhibtions. Features & Benefits Max Flag size W1000mm x H3500mm approx Overall height 5300mm max approx Portable and lightweight Unique design allows the flag to rotate when the wind direction changes Telescopic pole allows the flag to be set at three fixed heights Water filled base aids stability which splits down into four sections for easy carriage Quick to assemble and easy to use Optional carry bags available 3 x 320 pitch 20 20 Recommended 20 Flag dimensions 9 x 384 pitch 3500 13 x Eyelets (9.5 minimum internal dia ) Dimensions shown are to eyelet centres, are in mm 1000 and are approximate 24 Hardware Specifications Graphic Specifications Additional Info Overall assembled dimensions (mm): Recommended substrate: Wind Dancer 5m flags are designed Maximum height Lightweight flag textile to withstand approximate windspeeds W1000 x H5300 x D1000 approx Do not use banner vinyl of 13 to 18 miles per hour Intermediate height Recommended print process: (Beaufort Scale 4) W1000 x H4170 x D1000 approx Dye-sublimation print onto one Minimum height side of the flag only W1000 x H2900 x D1000 approx Maximum flag size (mm): Weight: 10kg approx empty and 76kg approx W1000 x H3500 when filled with water Intermediate flag size (mm): Capacity of base: 66 litres of water approx W1000 x H2500 (16.5 litres per base quadrant) Minimum flag size (mm): W1000 x H1500 We are continually improving and modifying our product range and reserve the right to vary the specifications without prior notice. All dimensions and weights quoted are approximate and we accept no responsibility for variance. E&OE. Kit includes: 4 x base quadrants (A) , A 8 x base connectors (B) , 1 x base stand (C) , 1 x base stand top (D) , H I 1 x base stand connector (E) , 10 x large rings and 4 x small rings (F) , (small rings are attached to top pole) 1 x telescopic pole (G) , 1 x top pole (H) , 1x pole stay set (I) , 4 x base screws (J) C B 1 x pole clamp (not shown) J F E D G 1 2 3 4 Turn the base stand upside Repeat step 1 with the Take the base stand top and Secure the base stand down and slot in the 1st base remaining 3 quadrants. slot into the four indents on connector onto the base quadrant. Ensure the quadrant plugs base quadrant. stand thread. are on the upper side. 5 6 7 8 Place a base connector Insert a base screw through Take a base connector (with Turn the base screw to fasten (without thread) into the the connector hole so that it thread) and place over the both quadrants together . indent of two of the quadrants appears underneath. end of the screw underneath Repeat steps 5 to 8 for the the base. remaining base connectors. 9 10 11 12 Attach the pole stay set to the Secure the stays to the base Slide the telescopic pole Slide the pole clamp over the base quadrants, placing each by slotting the locking pin through the hole in the pole telescopic pole. stay through the corresponding over the stay . stay set. hole on the base. 13 14 Seat the telescopic pole into Position the pole clamp near the base stand. to the top of the stay feet and tighten the thumbwheel to secure. 15 16 Fill each base quadrant with Attach 9 large rings to the water or sand to provide eyelets on the longer side of stability to the flag. the flag and 4 small rings to the shorter side. 17 18 Slide the small rings onto the Place the larger rings over top pole, ensure the rubber the telescopic pole. rings secure the end ring in place. 19 20 Attach the top pole to the Extend the telescopic poles to telescopic pole and tighten the desired flag height, ensure screw to secure. that each button locator clicks into position. 3500mm max 5300mm max 1000mm Base dimensions (mm): W1000 x H200 x D1000 All dimensions shown are approx.