How to instAll tHe pAdded foot plAte
stAndArd footbAr Allegro® reformer Figure 1
To install the foot plate (regular or Jumpus Maximus) on equipment with a To install the foot plate on the
“standard” footbar design, first loosen the two black knobs located beneath Allegro, first make sure the footbar
the standing platform at is in the proper position shown in
the foot end of the frame. Figure 1.
Place the spring bar into the
second “gear” (closest to the
carriage). Drop the shorter
of the two footbar supports Small knob inserted in second position Footbar “Plunger” Knob in second
into the first “gear.” The from top on the upper flange. rail hole from the stopper.
longer footbar support will Figure 2 Next, attach the new foot plate by
rest on top of the standing inserting the lower flange on the foot
platform. Gently slide the wooden tongue of the padded foot plate into the alu- Anti-wear strip and
plate into the foot plate clip as show
standing platform edge
minum bracket on the inside of the frame. Finally, tighten the two black knobs in Figure 2.
on the outside of the frame to lock the foot
plate into position. Lower Flange
Foot plate clip
Note that the black, padded portion of
the footbar is intended to be behind the
wooden block on the back of the foot Allegro foot plate (backside)
plate, not pulled up on top of it.
The backside of the footplate should be
resting against the footbar.
To install footplates on older
Allegros, see insert.
infinity footbAr personAl reformer footbAr
To install the foot plate (regular or Jumpus Maximus) on the Clinical Infinity foot-
To install the foot plate, place the upper 2 pegs located on the back of the foot
bar, first loosen the two black plastic knobs beneath the standing platform at the
plate on top of the reformer footbar. (NOTe: The upper pegs are approximately
foot end of the frame. Then, by releasing the bottom set of footbar plunger pins,
21⁄2” from the top of the foot plate. If
slide the footbar assembly horizontally
you are using the other pegs, the plate
into the 4th hole away from the foot end.
is upside down and cannot be secured).
Then release the plunger pins on the
Attach one end of a bungee cord into the
upright arms of the footbar and position
appropriate clip. Stretch the cord around
the cross bar so that the plunger pins lock
the back end of the reformer footbar
into the top hole. Next, place the tongue
and attach it to the clip on the opposite
of the foot plate into the bracket. Finally,
side of the foot plate. repeat the process
re-tighten the black knobs on the outside
with the other bungee cord.
of the frame.
reVo footbAr To install the padded foot plate (regular or Jumpus Maximus) on reformers with
To install the padded foot plate (regular or Jumpus Maximus) on the One-Step Footbar, first loosen the two black knobs located beneath the
reformers with the revo Footbar, first loosen the two black knobs located beneath standing platform at the foot end of the frame. Place the footbar support into
the standing platform at the foot end of the frame. Place the footbar support its lowest position. Gently lower the tongue of the foot plate into the aluminum
into its lowest (bottom) position. Gently bracket and tighten the black knobs until snug. The footbar should provide sup-
lower the tongue of the foot plate into port against the wooden block on the back of the foot plate.
the aluminum bracket. The top block of
the footbar should be resting against
footbar (not on). The bottom block I N N O v A T I O N I N P I l A T e S S I N C e 1 9 7 6
should be resting on the foot-end of the INFO@PIl ATe S.COM • w w w.PIl ATe S.COM
frame. Gently tighten the black knobs 80 0/ 745-2837 • 916/38 8-2838 • 916/379 -9277 FA x
until snug. 8220 FerGuSON AveNue • SACr AMeNTO, C A 95828- 0 931