Everest Printer Unpacking and Setup Guide - PDF

Document Sample
Everest Printer Unpacking and Setup Guide - PDF Powered By Docstoc
					            Rimage Everest II Printer™ Unpacking Instructions

    1
           Remove the Everest printer and accessories
           from the box.                                                             4 Remove the internal packing pieces.                                      6   Install the transfer ribbon.
                                                                                                                                                                                                                                 Transfer
                                                                                                                                                                    a. To access the transfer ribbon                             ribbon carrier
                                                                Ribbons                  a. Inside the Everest printer, remove the plastic packing pieces.             carrier, grasp the transfer ribbon
                                                                                                                                                                       carrier and pull out.
          Warning! Lift the
                                                                                                                                                                             Note: The transfer ribbon
           Everest printer with            Foam                                                                                                                               carrier slides out from the
           care; it is very heavy.                                                                                                                                            printer but remains attached.                             Takeup
                                                                      User Guide                                                                                                                                                        roller
                                                                                                                                                                    b. Install the transfer ribbon
          Note: Keep                                               Foam                                                                                               around the ribbon guides and
           all packaging                                                                                                                                               snap the ends of the ribbon
                                 Everest printer
           materials.                                                                                                                                                  into the ribbon carrier.
                                                                                                                                                                                                      Ribbon guides


                                                                                                                                                                    c. To tighten the ribbon, turn the takeup roller clockwise as
                                     Box                                                                                                                               indicated by the arrow.
                                                                                                                                                                                                                 Latch 

                                                                                                                                                                    d. Slide the ribbon carrier into the
                                                                                                                                                                       printer.

    2 Move the shipping screw.                                                       5 Install the print ribbon.                                                    e. Close latches 1, 2, and 3 as
                                                                                                                                                                       indicated by the arrows.
        a. On the back of the Everest printer,
           use a Phillips screwdriver to remove                                          a. To remove the ribbon carrier,                                           f. Close the printer side cover.                   Latch 2          Latch 3

           the shipping screw.                                                              grasp the ribbon carrier and pull
                                                                                            out.
        b. Using a Phillips screwdriver, install
           the shipping screw in the location
           indicated by the caution card.                                                                                                                       7   Set the switches.
                                                                                                                                                                    a. On the back of the printer, set the rotary switch so the
                                                                                                                                                                       recessed line points to your equipment type. Refer to the
                                                                                         b. Install the ribbon around the ribbon guides                                table below.
                                                                                            and snap the ends of the ribbon into the


    3 Open the Everest printer.
                                                                                            ribbon carrier.                                                              SW      Equipment                   Rotary switch

                                                                                                                     Ribbon guides                                       0       Standalone printer
                                                                Cover latches                                                                                                   Autoloader

        a. To open the side cover, press                                                                                                               Takeup            2       AutoPrinter
                                                                                         c. To tighten the ribbon, turn the                            roller
           the two cover latches and                                                        takeup roller clockwise as                                              b. On the back of the printer, set the voltage switch to match
           lower the side cover.                                                            indicated by the arrow.                                                    the AC outlet voltage.
                                                   Side cover

                                                                     Latch 

        b. Open latches 1, 2, and 3 as
           indicated by the arrows.
                                                                                         d. Insert the ribbon carrier into
                                                                                            the printer, but do not close the
                                                                                                                                                                8   Learn more.
                                                                                                                                                                    For more information about operating and maintaining the
                                                                                            latches.
                                                                                                                                                                    Everest printer, refer to the Everest Printer User Guide included
                                                                                                                                                                    with your product.

                                                                                                                                                                    For autoloader or AutoPrinter information, refer to the
                                                         Latch 2           Latch 3                                                                                  instructions included with your autoloader or AutoPrinter.
                                                                                                                                                                                                                                   0644_L