Docstoc

Technical Specification for Optical Receiver Module SDM9693-RC

Document Sample
Technical Specification for Optical Receiver Module SDM9693-RC Powered By Docstoc
					                                                                                                      Specification : TS-S97D021A
                                                                                                            Date : February, 1998




                                       Technical Specification
                                                 for
                                       Optical Receiver Module



                                                     SDM9693-RC


                     155.52Mb/s                               622.08Mb/s                                 1.25Gbps
                                                                                                  other ____________
                     Short Haul                               Long Haul                           other ____________
                     Intermediate Reach                       Long Reach
                     Single 5.0 V                             Single 3.3 V                        other ____________

                     1.3 µm                                   1.55 µm                             other ____________

                     Transmitter                              Receiver                            Transceiver

                                                     (       2R /           3R )         (        2R /         3R )



                  SUMITOMO ELECTRIC INDUSTRIES, LTD.


SUMITOMO Electric reserves the right to make changes in the specification described hereinafter without prior
notice.

#Safety Precaution                    Symbols This specification uses various picture symbols to prevent possible injury to operator or
other persons or damage to properties for appropriate use of the product. The symbols and definitions are as shown below. Be sure to be
familiar with these symbols before reading this specification.

        Warning          Wrong operation without following this instruction may lead to human death or serious injury.

        Caution          Wrong operation without following this instruction may lead to human injury or property damage.

Example of picture symbols        indicates prohibition of actions. Action details are explained nearby.
                                  indicates compulsory actions or instructions. Action details are explained near by.

(SDM9693-RC)                                                  -1/5-
                                                                                                        Specification : TS-S97D021A
                                                                                                              Date : February, 1998
1. General
The features of SDM9693-RC are listed below.

      * Data Rate              1.25 Gbps
      * Power Supply Voltage Single -5.0V
      * Electrical Interface  ECL
      * Sensitivity            -8 ~ -22dBm
      * Detector              InGaAs PIN-PD
      * Connector Interface   SC Receptacle
      * Pin Configuration     24pin Dual In Line
      * Low Power Consumption
      * Plastic Molded Package
      * Signal Detect (FLAG) Function



2. Block Diagram

                                                                            Comparator                        SD


                                  PIN-PD


                                             Pre                 Main           ECL                           RD
                                           Amplifier            Amplifier      Buffer
                                                                                                              RD


                                                  Figure 1 Block Diagram



3. Package Dimension

                                                        PIN24               PIN13
                                                                                                15.24
                                                                                        14.32
                          15.2




                                                                                                                        t=0.25
                                                                                                                1.5              1.5

                                                        PIN1                PIN12
                                                                   36.4                                                          2.0
                                                            53.3
                                                                                                              3.5




                                                                                                                             3.5
                                 9.2




                                                                                                              0.5
                                                                                    8.9




                                                                                                                              0.5

                                                                                    4.9                 2 ~ 24pin            1pin
                                       2.54PX11=27.94                                                               Lead pin
                                                                                                                         UNIT:mm

                                                 Figure 2. Package Dimension


                                                                 Caution
    Do not disassemble this product. Otherwise, failure, electrical shock overheating or fire may occur.
    Handle the lead pin carefully. Use assisting tools or prospective aids as required. A lead pin may injure skin or human body

(SDM9693-RC)                                                   -2/5-
                                                                                                                   Specification : TS-S97D021A
                                                                                                                         Date : February, 1998
4. Pin Assignment
                   Function                        Symbol        No.                     No.      Symbol                   Function
                   Ground                           GND           1                      24         Vee             Power Supply (-) : -5V
                   Ground                           GND           2                      23         NC                Non Connection.
                   Ground                           GND           3                      22         NC                Non Connection.
                   Ground                           GND           4                      21         NC                Non Connection.
                   Ground                           GND           5                      20        GND                     Ground
                   Ground                           GND           6                      19        GND                     Ground
                   Ground                           GND           7                      18        GND                     Ground
                   Ground                           GND           8                      17         NC                Non Connection.
                   Ground                           GND           9                      16         RD       Differencial Data Output (Positive)
                   Ground                           GND          10                      15         RD       Differencial Data Output (Negative)
                   Ground                           GND          11                      14         NC                Non Connection.
                   Ground                           GND          12                      13        FLAG       Flag Output (Refer to Figure 3.)
 *NC pins are not connected to the internal circuit.
 *NC pins should be left open for additional functions in the future




5. Absolute Maximum Ratings
                            Parameter                           Symbol            min.            Max         Unit            Note
                Storage Case Temperature                          Ts               -40             85          °C              1
                Operating Teperature                              Ta                0              60          °C
                Supply Voltage                                   Vee              -6.0            0.0           V
                Lead Soldering (Temperature)                                                      260          °C              2
                              (Time)                                                               10         sec.
                Note 1. No condensation allowed. 2. Measured on lead pin at 2mm (0.079in.) off the package bottom



                                                                          Warning
     Use the product with the rated voltage described in the specification. If the voltage exceeds the maximum rating, overheating or fire
     may occur.

                                                                          Caution
      Do not store the product in the area where temperature exceeds the maximum rating, where there is too much moisture or damp-
      ness, where there is acid gas or corrosive gas, or other extreme conditions. Otherwise, failure, overheating or fire may occur.




6. Electrical Interface
       ( Unless otherwise specified, Vee = -4.75 to -5.25 V and all operating temperature shall apply. )
                     Parameter                           Symbol           min.             Typ.          Max.          Unit          Note
   Supply Voltage                                         Vee             -4.75           -5.00          -5.25          V
   Supply Current                                         Idrx                             130            170          mA             1
   Data                              High                 Vrdh           Vcc-1.08                       Vcc-0.72        V             2
   Output Voltage                    Low                  Vrdl           Vcc-1.95                       Vcc-1.59
   FLAG                              High                 Vflgh          Vcc-1.02                       Vcc-0.88        V             3
   Output Voltage                    Low                  Vflgl          Vcc-1.81                       Vcc-1.63
   Note 1. Output bias current is not included. 1.25Gbps, PRBS2^23-1
   2. Vee=-5.2V, Ta=25°C, Termination condition : Rl=50Ω to -2V
   3. Vee=-5.0V, Ta=25°C, Termination condition : Rl=50Ω to -2V




(SDM9693-RC)                                                             -3/5-
                                                                                                                Specification : TS-S97D021A
                                                                                                                      Date : February, 1998
7. Optical Interface
      ( Unless otherwise specified, Vee = -4.75 to -5.25 V and all operating temperature shall apply. )
                  Parameter                                   Symbol         min.          Typ.         Max.         Unit      Note
   Data rate                                                                               1.25                      Gbps
   Transmission Code                                                                NRZ, Mark ratio 50%
   Transmission Pattern                                                               PRBS 2^23-1
   Minimum Sensitivity                                         Pmin                                     -22.0        dBm         1
   Overload                                                    Pmax          -8.0                                    dBm         1
   Total Jitter                                                 Tj                                      344          psec       1, 2
   Flag Assert Level                                            Pa                          -33                      dBm         3
   Flag Deassert Level                                          Pd                          -35                      dBm
   Note 1. BER=10^-10, 1.25Gbps, NRZ, Mark ratio 50%. 2. Optical input power: -8.0 ~ -22.0 dBm
   Note 3. Please refer to Figure 3.

                                                        "H"
                                          FLAG Output



                                                        "L"


                                                                      Pd         Pa
                                                                   Optical Input Power
                                     Figure 3. FLAG Assert Level and Deassert Level


8. Relation between Received Optical Signal and Data Output
                                   Received Optical Signal                          Data Output
                                                                                  RD          RD
                                                        "H"                       "H"         "L"
                                                        "L"                       "L"         "H"


10. Recommended User Interface
                                                                             L1
               GND                                                                           1 ~ 12, 18~20



                             R1                           R1            C1        C2

               FLAG                                                                          13

               RD                                                                            16

               RD                                                                            15
                             R2                          R2            R3
                Vee                                                                          24


                                                         : Characteristic impedance 50ohm line should be symmetrical
                R1 = 82Ω (≥ 1/8 W), C1 = 100µF (Tantalum Electrolytic or Aluminum Electrolytic Capacitor)
                R2 = 130Ω (≥ 1/8 W), C2 = 1µF (Ceramic Capacitor)
                R3 = 510Ω (≥ 1/8 W), L1 = Ferrite Bead ZBF 253D-00 (TDK)

                             Figure 4. Recommended User Interface




(SDM9693-RC)                                                                -4/5-
                                                                                                         Specification : TS-S97D021A
                                                                                                               Date : February, 1998
11. Other Precaution
Under such a strong vibration environment as in automobile, the performance and reliability are not guaranteed.


The governmental approval is required to export this product to other countries. To dispose of these compo-
nents, the appropriate procedure should be taken to prevent illegal exportation.


This module must be handled, used and disposed of according to your company's safe working practice.


                                                                 Warning
     Be sure to carry out correct soldering for connection to peripheral circuits in order to prevent contact failure or short-circuit. Other-
     wise, a strong laser beam may cause eye injury, overheating or fire.
     Do not put this product or components of this product into your mouth. This product contaions material harmful to health.



                                                                  Caution
     Be sure to turn the power off when you touch this product connected to the printed circuit boards. Otherwise, electric shock may occur.

     Dispose this product or equipment including this product properly as an industrial waste according to the regulations.




12. Ordering Information
                                           Connector type            Ordering Number
                                                                      Ta = 0 ~ 60°C
                                                  SC                  SDM9693-RC




13. For More Information
U.S.A.                                          Europe                                            Japan
Sumitomo Electric Lightwave Corp.               Sumitomo Electric Europe Ltd.                     Sumitomo Electric Industries, Ltd.
78 Alexander Drive                              Unit 11, Magnolia House                           ( International Business Division )
Research Triangle Park, NC 27709                Spring Villa Park, Spring Villa Road              3-12, Moto-Akasaka 1-chome
Tel. (919)541-8100                              Edgware, Middlesex, HA8 7EB,                      Minato-ku Tokyo 107-8468
Fax. (919)541-8376                              United Kingdom                                    Tel. (03)3423-5771
E-mail: info@sel-rtp.com                        Tel. (081)905-6160                                Fax. (03)3423-5099
http://www.sel-rtp.com                          Fax. (081)905-6195



E-mail: product-info@yfocs.sei.co.jp
http://www.sei.co.jp/Electro-optic/eopd_home_e.html




(SDM9693-RC)                                                    -5/5-

				
DOCUMENT INFO
Shared By:
Categories:
Stats:
views:9
posted:3/16/2010
language:English
pages:5
Description: Technical Specification for Optical Receiver Module SDM9693-RC