REVERSE OSMOSIS SYSTEM PLUMBERS INSTALLATION MANUAL by fnz82095

VIEWS: 250 PAGES: 7

									   REVERSE OSMOSIS SYSTEM
PLUMBERS INSTALLATION MANUAL
HOW TO USE PUSH-IN FITTING


                                 COLLET
LOCKING CLIP

                                          TUBE




               Make sure the end of the tube does not
               have any scratches or is not damaged in
               any way


               If the end of the tube is damaged, then
               use a sharp cutter to cut away any damaged
               tube. Make sure the end of the tube has
               a clean straight surface


                To make a connection, push the tube firmly
                into the fitting




                Make sure the tube is pushed as far as it
                can go



                Pull on the tube to make sure it is secure.



                After the tube is secure insert the locking
                clip behind the collect.




                To disconnect, remove locking clip then
                use two fingers to push onto the collect
                and use other hand to pull out tube.
                                               S PT
                            Ro
                       ater co
                         er connection
    Making the supply water con
                                TE
                           FIL
                      ER
                       Ball Valve
                       Ba l V                               Copper Pipe
    Flexible Pipe

                    AT
                                                            (Not Supplied)
    (Not Supplied)

    To Kitchen Tap W
                 p                                           To Kitchen Tap
                AL
                                  Close

    T PieceTR
      Piece
         ce                                                  T Piece
        N              Ball Valve

    CE                                                                          Ball Valve


                                                                    TD
              Ball Valve
     Washer
                                  Open
                                                              Washer
                                                                 he
                                                                  e
                                                                  er
                                                               asher
                                                              Washe
                                                                   L
            Stop Cock                                              Stop Cock

                                        TE
            (Not Supplied)                                         (Not Supplied)

                                     FIL follow one of the
                             ng coRfig
                              gcconf
Depending on your plumbing configuration
                           ct TE
                         nec the
                           c
above diagrams to connect the T piece and ball valve to the cold
water supply in the k chenA
                     kitc W ensure the green washer is inserted
                     kitchen,
                     ki
inside the T piece andL not over tight any parts.
               ece a A do
               ece d d
                 TR
          C EN
       on
      Connecting the Pressure Limiting Valve
           Ball Valve             Pressure Limiting Valve
                                                                  Y LTDConnect
                                                            PT               To Filter
                                                                             Housing

                                              TE
                        Small                                                Inlet
                                     MountinIL
                        Length

                                      RF
                        Of Tube      Mo nting Bracket
                                     Mounting


                           all valvT
                                     E
                             WA the pressure limiting valve
                               valv
                               valve
                                  v
 Once the T piece and ball va ve is connected cut a small piece
 of the red tubing for c L n
                         connecting
                           nne
                      or con
 to the ball valve, u RA rest of the red tubing for connecting
                 e, e the
                ve use th
 the pressure lim T valve to the filter housing inlet. Secure the
          sur liN t
             re miti
           ur limiting
             CE
 pressure limiting valve to the mounting bracket.
           limit
                                                            S PT
             Connecting the drER pipe
                            dra
                            drain
                          e d ain
  For single bowl sink R F
                     k
                           ILTFor double bowl sink
                             ATE
                            W
               TR
            Minimum Level

              N



                                            os s waLT
                                                        ER to flow into your
                                                   I single bowl sink make sure
                                                 wastte
The drain clamp allows the reverse osmosis waste water
drainage. Drill a 6mm hole in your PVC pipe F
                                        VC p R fofor
                                         C pipe, f
the hole is above the minimum level,TEdouble bowl sink the best location
                                    evel for
                                    ev
                                    e el, for
                                   level fo
is on the double sink connector as A
                                   WAlign the outletthethe drain clamp with
                              ector s sshown. Loosen
                                       sh                   screw and wrap the
drain clamp around the PVC pi
                              AL tighten the screwinto secure the drain clamp.
                              C
                         e PVC pipe.
                    just dR
                      st drilled
the hole you have jus drille and
                     NT
                 CE
                  Screw
                          Drain Clamp



                                                                        LTD
                                        Brass Olive
                                                      Securing Nut


                                                                 P  TY

                                         RF
                                        Backing Nut



                              wn andA TE one spanner to clamp onto the
 Arrange the black pipe as shown and use
                                   an
                                 Wnd
                            AL
                         nd wh e
                           d while
 backing nut with one hand w ile tightening the securing nut with another

                       TR
 spanner.


                C EN
                                                         TY
                                                       SP
                                                 ER
                                           F ILT
                         ER
                       AT
                                                       Ball Valve      Ball Valve
                                                       Closed          Open

                     LW
                   RA
                                                                           Ball Valve



            E NT
        C
                      Pure Water                         Pure Water Storage Tank
                      Compartmanet


                      Diaphram


                                           RF
                      Pressurised Air
                      Compartment       ATE                                  Air Valve




               C EN
    Cut out of pure water storage tank                                          age
                                                                                 g
                                                 Installation of pure water storage tank

                                                                             TD
                                                                           YL
                                                                        tubing o
                                                                        tub g on
Screw the ball valve on to the pure water tank and connect the blue tubing onto the ball
                                                                  ir, whic pushes the pure
                                                                   r, wh ch
valve. The pure water storage tank contains a compartment of air, w ich p
                                                                      which
                                                                      PT
                                                                  corret
                                                                       et
water out when you open the tap. The pressure in the ball is set corre by the manufacturer,
                                                                  corretly
                                                                    S
                                                         ER
                                                            he ank
however every year you should check the air pressure in th tank You can do this by first
                                                           the tank.

                                                     ILT
                                                    pt
                                                    p y all t
                                                    pty a
disconnecting the tank from the blue tube and empty all the water in the tank, then remove
                                                    e pre
                                                      p es
                                                        e
the air valve cap and using a bike tyre pump, set the pressure in the tank to 7psi or 48kPa.
                                                   F
                                              ER
                                            he b    t
                                                    tu
After the pressure is set, you can connect the blue tube back to the tank.


Important                             W   AT
                                   Lf pure water that is filled into the tank. As the first tank
                         firs ta A o
                         first ank
Do not drink or use the first tank of
of water is used to flush theR
                        h
                           T system.isWhen the firstthis subsequent tanks of open thereadyand use.
                      ush e sy
let the water run ou uNl the tank empty. After
                                                     tank is filled you should               tap

                      E
                  out until
                n o unti                                                         water is        for
                                                  S PT
                Connecting TLTE
                         g The T
                           The Tap
                                              R
                            FI
                         ER
                      WAT


                                                                LTD

                       Chrome Plate
                                    Wa
                       Large Rubber Wa
                                    Washer                      Small Rubber Washer

                            TE
                       Sink                                     Sink

                          WA
                            Locating Washer
                              c
                              ca ng
                              catin
                       Hard Locating W                          Hard Locating Washer
                        Op
                         ptional)
                         ptional)
                       (Optional)                               (Optional)


                     R AL
                       St W
                       S Washer
                       Star
                       L
                       Locking Nut
                                                                Star Washer


                NT
                                                                Locking Nut


          C   E   Tap Fitting                               Tap Fitting


                  White Tube                                       be
                                                                   be
                                                           White Tube


                                                                Y LTD
                                                         S PT
                                              w ere
                                                    ER
                                            p whe e y
Drill a 12mm hole in the sink or benchtop where you would like to
                                                ILT
install the tap and choose one of the configurations above to
                                          onfig
                                             igu
                                              g
                                         config
                                              F
                             ER
connect the tap. Tighten the locking nut to secure the tap, ensure
                                   king u
                                   kin
                                  ck ng nut
                           ATe tap fit
                               tap fi
you do not over tighten the tap f tti Insert the tubing from the
                                   fitting.

                         LW
                       p fi ting.
white tube into the tap fittting
                         fitting.

                       RA
                E NT
            C
                                S PT
                                   ER
                               ILT
                              FProcedures
                         a tup Pr
               Initial Startup P
                           ER
1. Once all the indATW vii
                      div
                      dv
                 e individual compoents are installed
             l neeL
           ill need
                ee
   you will need to close the pure water tank ball
   valve,NT
     alve, o
        ve op
           open
               RAthe tap, and open the inlet connection
       CE
     all                                            in
   ball valve. Allow the water to run for 10 minutes.
                                                   TD
2. Close the tap and open the ball valvT i    e
                                            lve Y Lthe
                                          valve in
                                      ow
   pure water tank. This will allow R tankS P to
                                     low the
                                     low th
                                     LE
   fill with water. Wait 1 hour foTthe tank to fill
                                  r for
                                     o
                                ur fIor
   with water.                 RF
                             TE
                         WA
3. Now open the La and allow the pure water
                n thA tap
                       ta
                    he t
           o dN
    tank to dra  TR for about 10 minutes and close
           C
          ap
    the tap.
                 ai
              E rai
               drain


                                        njoy L
                                        njo Y
4. Your installation is now complete. En oy us
                                              TD
                                       Enjoy using
   Reverse Osmosis Filtration System. P
                                  tem.
                                   emS
                                          T
                                    ER
                                ILT
                             RF
                          TE
                        WA
                   AL
                TR
            EN

								
To top