Docstoc

eagle_koh

Document Sample
eagle_koh Powered By Docstoc
					Eagle                                                                            c   Ronald Koh - 1988


             1.                                                     2.
                                Use a thin sheet of paper or
                                tissue foil of at least 15 cm
                                square.




Fold diagonally in half from left to right,          Valley fold the lower diagonal edges to the
crease well, and unfold. Repeat by folding           crease line in the centre and turn paper over.
in half from top to bottom, and unfold.

      3.                        4.




                                                             Open out to the sides, effectively
                                                             unfolding Step 2.




                                                        5.




                  Fold down the triangular
                  section at the top and turn
                  paper over.




 6.

                                                  Make two diagonal folds as illustrated, in line
                                                  with the edge of the triangular layer underneath.
                                                  Crease firmly, and unfold.




                                  Lift up the triangular piece from behind.
                  7.                                                8.




  Repeat from Step 2 on the lower half of the       Valley fold through the circled intersecting
  paper, then turn the paper over.                  crease lines, crease firmly, and unfold.


                  9.                                10.




                                                  ... like so. Now fold the diagonal edge in the
                                                       middle to the vertical crease in the centre,
                                                       crease firmly, and unfold. Repeat on the
                                                        other side.


                                                   11.

      Collapse the paper along the illustrated
      mountain and valley folds ...



12.




                                                    Pull the flaps on each side slightly apart and
                                                    sink fold. You may need to stick a finger
                                                    through the underside to guide the sink fold
                                                    precisely along the crease lines made in Step
                                                    10. Repeat on the other side.


  Flatten the rest of the model to the position
  at Step 10.
13.                                                         14.




                                                                             Fold the bottom corner to
  Separate the two diagonal edges on the                                     the top, crease well, and
  right and squash fold. Repeat behind.                                      unfold.

       15.                                      16.                                    17.




Separate the two diagonal              Fold and unfold, creasing                      ... then petal fold.
edges and squash fold                  firmly ...
again.

      18.                                       19.                                    20.




 Fold the triangular flap               ... then fold the flap on the           Grasp the circled point
 down ...                                   left to the right. Repeat           and gradually pull the flap
                                             from Step 15 on the next           upwards as far as it can
       21.                                   flap on the left.                  go, opening out and
                                                                                flattening the layers
                                                                                beneath ...

                                                      22.




                    ... like this, before bringing                      The model should now look
                        down the flap again.                            like this. Turn the model over.
      23.                                24.                            25.




 Repeat Step 15 on the           Mountain fold the triangular   Fold the first flap on the
 right, and then on the left.    portion of the uppermost       right to the left.
                                 layer under and against
                                 itself.
     26.                              27.                               28.




Fold and unfold, creasing         ... then reverse fold.          Fold and unfold again,
firmly ...                                                        from the left corner to the
                                                                  corner on the right.

      29.                              30.                              31.




Now mountain fold the           ... then close up with a          Fold the flap on the left
excess paper under as                 rabbit's ear fold.          to the right and repeat
well ...                                                          from Step 26 on the
                                                                  other side.

      32.                              33.                               34.




Bring the corners from               Squash fold ...              ... and then petal fold,
the sides to the apex.                                                  as you did in
                                                                  Steps       16 to 18.
35.                               36.                                         37.




Grasp the flaps at the             ... then reverse fold to hide                           Turn model
circled area and pull                   the triangular tab                                 over.
gently apart, ...                        beneath.

      38.                                 39.

                                                                                40.




Swivel both layers to              ... grasp the paper at the
the left, ...                          circled area and make a
                                       crimp fold while drawing          ... like this. Return the two
                                       the paper, slightly beyond            layers folded in Step 38 to
                                        midway, towards the top ...          the right and flatten out.

      41.                                 42.                                  43.




                                  The pieces on each side,             ... then valley fold the sides of
The model should now look         which will form the wings,               the top layer to narrow.
like this. Repeat Steps 38 to     should be symetrical. Reverse
40 on the left side of the        fold each of the tabs on the
model.                            sides ...

            44.                             45.                                     46.




Valley fold the tail piece         Mountain fold the first layer at      ... and reverse fold to hide the
upwards, crease firmly, and        the bottom corner of the wings        lower portion of the tailpiece
unfold. Next crimp fold the        within itself, then separate and      within the opening ...
layer at the base of each wing     draw the central vertical edges
as illustrated, then turn model    of the tailpiece to the sides ...
over.
                 47.                                                   48.




... like this. Now valley fold the corners of the      Crimp fold the front of the wings as
     second layer of the wing within itself, and       illustrated.
     widen the tail by folding out the
     overlapping tabs in the middle.

                 49.                                                50.




  Bring down the uppermost flap with a                  ... crimp fold through all remaining
  valley fold, ...                                            layers at the top to form the
                                                                head ...

                          51.
                                                                 52.




               ... and mountain fold the model
                         vertically in half


                                                                   Now to form the left claw. First,
   53.                                                             fold and unfold ...


                                                     54.




... then do an outside reverse fold using
    the crease lines made in Step 52. You
    will need to open out the layers
    temporarily to do this.
                                                    Inside reverse fold the claw, then outside
                                                    reverse fold at the tail.
     55.                                                   56.




Pull down the lower beak just a little.                Valley fold both sides of the head and neck
Reverse fold the tip of the left claw once             area as illustrated.
more as illustrated, then repeat from Step
52 on the right claw.

                                                                59.

    57.                         58.




Outside reverse fold               ... like this.
the tip of the beak ...




           60.
                                                            Fold down the wing on this side ...




    ... then crimp the wing with a series of
        mountain and valley folds as illustrated.
        Repeat from Step 59 on the other wing.




                      Finally, spread out and curve the wings
                      for greater realism.

				
DOCUMENT INFO
Description: 81 kind to use the time Funny with paper