Ademco Programming Cheat Sheet by tamir13

VIEWS: 0 PAGES: 3

									Ademco Programming Cheat Sheet                                                                              Page 1 of 3
Ademco Programming Cheat Sheet

Ademco Programming is quite simple. First you enter programming mode by using your Installer Code Then Code Key
"8" Then 00. Some Vista Series Systems you anly need one 1 "0". Please refere to your installation guide.

Once in programming do the following. * + Field Number fills the field in Or Changes the value of the field. # + Field
Number makes the system read the field values back to you.

The following are the basic Ademco programming setup values for A Vista 10Se. These Fields Need Changing From
Default Values.
See Your Programming Guide For Other Vista Systems As The Field Values Do Vary With Different Ademco
Systems.

              Insert
Filed #                 Description Of What The Field Value Does. Further Descriptions And Warnings
              Value
                                                                        Do Not Change It Till You Are Completely
* + 20           1      Changes Your Installer Code.                    Done Programming And You Are Completely
                                                                        Familure With The Programming Sequence.
                                                                        Make Sure That You Have Set A Master Code
                                                                        Into The System. If You Do Not And You
* + 21           1      Enables Quick Arm Feature.
                                                                        Quick Arm The System You Will Lock
                                                                        Yourself Out Of The Panel.
                                                                        Insert A 1 For 5800 Series Receiver Only If
                                                                        You Are Using Wireless. If You Have No
* + 22           1      RF Receiver Select
                                                                        Wireless Leave This Field Set To "0" NOT
                                                                        USED.
                                                                        You Can Change The Time That The Siren
                                                                        Resets After An Alarm Has Gone Off. See
* + 30           3      Alarm Siren/Bell Timeout 12 Minutes
                                                                        Your Programming Manual For Other Values
                                                                        For Other Timeout Durations
                      Enter Your Central Station Primary Phone
                                                                    Do Not Use If You Have No Central Station
* + 41          Ph#   Number Here. Always Start With A 1 + Area
                                                                    Hookup.
                      Code If Not In Your Area.
                                                                    Do Not Use If You Have No Central Station
* + 43       Sub Id Your 4 Digit Central Station Account Number
                                                                    Hookup.
                      This Field Sets Your Panel To Tone Dial       Most Panels Now A Days HAve This
* + 43          1
                      Rather Than Old Rotary Dial.                  Defaulted To "1". Refere To Your Manual.
                                                                    Use This As Todays Standard For The System
* + 45          7     Standard Report Format Contact ID.            To Communicate With Central Station
                                                                    Receiver.
                                                                    Always Set This To "0". Otherwise The
                                                                    Dialer Will Wait 15 Seconds Before Dialing
* + 48          0     Dialer Delay
                                                                    Central Station On Any Alarm Except For
                                                                    Panics.
Below Are Report Code Values. If The Field Requires 2 Digite Then Enter 1+0 IE: 10 For A Report Code Of 1 To
Enable Contact ID Report.
                                                                    This Will Allow The System To Send A
* + 62          1     AC Loss Report Code
                                                                    Report To Central Station.
                                                                    This Will Allow The System To Send A
* + 63          1     Main System Low Battery Report Code
                                                                    Report To Central Station.


http://nassausecurity.com/cheatsheets/ademcocheatsheet.html                                                  5/21/2004
Ademco Programming Cheat Sheet                                                                          Page 2 of 3
                                                                     This Will Allow The System To Send A
* + 67          1      RF Transmitter Low Battery Report Code
                                                                     Report To Central Station.
                                                                     This Will Allow The System To Send A
* + 73           1     AC Restore Report Code
                                                                     Report To Central Station.
                                                                     This Will Allow The System To Send A
* + 74           1     Main System Low Battery Restore Code
                                                                     Report To Central Station.
                       RF Transmitter Low Battery Restore Report     This Will Allow The System To Send A
* + 75          1
                       Code                                          Report To Central Station.

* + 56 Is Your Zone Programming Section Or Page 2 Of Programming. First Enter * + 56 And You Will See
Another Screen Sometimes That Says Custom Alpha Descriptors. Just Hit " * " To Continue. You Will Then See "
ZONE 1" On Your Display. If You Wish To Setup Another Zone Other Than 1 Simple Enter That 2 Digit Zone
Number Here And Hit " * " To Continue.

You Will Then See A Screen Which We Call A Zone Value Screen. That Tells You What If Any The Zone Is Setup
For. ZN=Zone# RP=Report Code ZT=Zone Type PT=Partition # IF Panel Has Partitions IF YOU HAVE
WIRELESS THE FOLLOWING APPLIES= RF=RF Transmitter Type. L=Sensor Loop Of That Particular
Transmitter.

Hit " *"

You Will Then See ZONE TYPE. Below Are The Most Common Zone Types. Please Refere To Your Installation Or
Programming Instructions For Other Zone Types.

00=NOT USED
01=Entry/Exit Delay Loop Alarm
03=Perimiter Instant Alarm
04=Interior Motion Alarms
06=Silent Panic
07=Audible Panic
09=FIRE Smokes Heats Etc

Once You Have Set The Zone Type Hit " * "

You Will Be In Your Report Code Setup Screen. You Want A 10 On The Right Of Each Zone Weither You HAve
Central Station Or Not.

The Report Screen Will Look Like The Following. 00 - 00 - 10 If The Screen Reads All "0"'s Thes Simply Hit "01"
And A "10" Will Appear On The Right Of Your Screen. Once You Have A "10" On The Right Of Your Screen Hit "
*"

If You Are Programming A Wireless Device The System Will Prompt You To Enroll The Wireless Device ID
Number.
If You Are Programming A Hardwired Device The System Will Now Ask You If You Want To Programe In Alpha
English Descriptors For The Keypad To Display. If Yes Press " 1 " For Yes. If No Press " * " To Start Programming
Your Next Zone.

If Yes Press "1" The Zone Number That Your Working On Will Appear As IE: ZONE 01.
To Start Programming Your English Descriptor For That Zone, Enter " * " Then The Zone Number You Are On.
IE: If You Are On Zone 1 Re Enter " * " Then " 01"
The System Will Now Be Asking For A 3-Digit Word Number. Refere To Your Installation Guide For The Word To
Number Conversion Alpha Descriptor Table. Once You Have Entered Your First Word Hit " 6 " To Continue To
Word # 2. Enter Word # 2 3-Digit Number Then Hit " 6 " To Continue To Word # 3. Once You Are Done With Any


http://nassausecurity.com/cheatsheets/ademcocheatsheet.html                                              5/21/2004
Ademco Programming Cheat Sheet                                                                  Page 3 of 3
Or All 3-Words Hit " 8 " To Exit Alpha Descriptor Programming.

You Will Now Be At The Next Zone You Wish To Programe. If You Want Another Zone Than The One Displayed
Simple Enter The Zone Number And Hit Star, Then Follow The * + 56 Instructions Again.

Thats it for Ademco Programming. The Ademco Lynx Is About The Same Just In *+56 Zone Programming You Will
Follow "A B C D E" These Letters Will Tell You Where In Star 56 You Are At.




http://nassausecurity.com/cheatsheets/ademcocheatsheet.html                                      5/21/2004

								
To top