Your Federal Quarterly Tax Payments are due April 15th Get Help Now >>

HP-175225 INSTALLATION MANUAL VISTAWALL ARCHITECTURAL PRODUCTS by raa13961

VIEWS: 1,104 PAGES: 42

									             HP-175/225     INSTALLATION                  MANUAL




                 VISTAWALL ARCHITECTURAL PRODUCTS
                      Central Operations & Headquarters
                               803 Airport Road
                               Terrell, TX 75160
                            Phone: 972-551-6100
                              Fax: 972-551-6264

                        WWW.VISTAWALL.COM




April 2003
HP-175 & HP-225
WA L L S Y S T E M S

 I N S TA L L AT I O N

        AND

     GLAZING

     MANUAL


        April 2003
             HP-175/225   INSTALLATION       MANUAL




                    HP-175 & HP-225
                    WA L L S Y S T E M S

                     I N S TA L L AT I O N

                            AND

                          GLAZING

                          MANUAL


                            April 2003




April 2003                                            1
            HP-175/225                             INSTALLATION                                    MANUAL


            HP-175 & HP-225 INSTALLATION & GLAZING
                         INSTRUCTIONS
        These instructions are to be used for typical installations. Reference
        shop drawings for special notations on installations and glazing.


                                       TABLE OF CONTENTS
    Material Handling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 3

    General Construction Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 3

    General Installation Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 3

    Fabrication & Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 4-8

    Clip & Diverter Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 9

    Glazing Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 10-11

    Splice Details . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 12

    Anchorage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 13

    Glazing Adapter Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 14

    Deglazing and Reglazing Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 15

    Door Details . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 16-17

    Butt Glaze Mullion Fabrication & Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 18-19

    Butt Glaze Mullion Glazing Details . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 20-21

    Butt Glaze Mullion Clip & Diverter Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 22

    Outside 90° Corners . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 23-26

    Inside 90° Corners . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 27

    Outside 90° Butt Glaze Mullion Fabrication & Assembly . . . . . . . . . . . . . . . . .Page 28-30

    Inside 90° Butt Glaze Corner Detail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 31

    Glazing Adapter Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 32

    Single Span Windload Charts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 33-35

    Horizontal Dead Load Charts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 36

    Perimeter Anchorage Methods . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 37

    Twin Span Wind Load Charts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 38-39

    Glazing Options and Accessory Chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 40


2                                                                                                                              April 2003
             HP-175/225   INSTALLATION   MANUAL

                   GENERAL INFORMATION




April 2003                                        3
    HP-175/225   INSTALLATION   MANUAL

          MULLION FABRICATION AND
         SHEAR BLOCK INSTALLATION




4                                        April 2003
             HP-175/225   INSTALLATION   MANUAL

                   SILL & HEAD FABRICATION
                AND SHEAR BLOCK INSTALLATION




April 2003                                        5
    HP-175/225   INSTALLATION   MANUAL

           SEALANT PROCEDURES
        FOR HEAD, SILL & HORIZONTAL
          WITH INTEGRAL DIVERTER




6                                        April 2003
             HP-175/225   INSTALLATION   MANUAL

                    SEALANT PROCEDURES
                     FOR JAMBS & MULLS




April 2003                                        7
    HP-175/225   INSTALLATION   MANUAL

        PERIMETER SEALANT DETAILS




8                                        April 2003
             HP-175/225   INSTALLATION   MANUAL

                     INTEGRAL DIVERTER
               HORIZONTAL BRIDGE INSTALLATION




April 2003                                        9
     HP-175/225   INSTALLATION   MANUAL

        INTEGRAL DIVERTER HORIZONTAL
              GLAZING DETAILS




10                                        April 2003
             HP-175/225   INSTALLATION   MANUAL

                INTEGRAL DIVERTER HORIZONTAL
                      GLAZING DETAILS




April 2003                                        11
     HP-175/225    INSTALLATION    MANUAL

                  SPLICE DETAILS




12                                          April 2003
             HP-175/225   INSTALLATION   MANUAL

                    MULLION ANCHORAGE




April 2003                                        13
     HP-175/225   INSTALLATION   MANUAL

             GLAZING ADAPTER
               INSTALLATION




14                                        April 2003
                      HP-175/225                           INSTALLATION                                   MANUAL

                       DEGLAZING & REGLAZING INSTRUCTIONS


         DEGLAZING INSTRUCTIONS
         A. In order to remove a lite of glass, it is necessary to remove one face member. On the butt glazed system it will also be necessary to
             cut and remove the vertical silicone joints at the interior and exterior of the glass.

         B. The procedure for removing any face member is shown in Figure D-2.
           1. Remove exterior glazing gasket in order to provide access to plastic clips.
           2. Insert thin bladed chisel through the space between the glass and aluminum face.
           3Slide the chisel until it comes in contact with a plastic clip and slide clips to one end of
               horizontal or vertical. Repeat process until all clips are located at end of cap, then slide
               face cap off of clips.
           4. Remove balance of exterior gaskets on lite to be removed.
           5. Remove lite of glass per standard glazing practices.
           6. Maximum glass size for replacement litre in HP-1750 equals 5/8" over daylite opening.
           7. If all faces are removed, glass size equals original sizes.

         REGLAZING PROCEDURE
         1. Remove old clips from face member by sliding out one end.
         2. On intermediate horizontal gutter members, slide the gutter portion of the old clips sideways so new clips can be inserted.
         3. Insert new plastic clips into gutter member.
         4. Position setting blocks and jiggle glaze new lite of glass into opening.
         5. Mark location of plastic clips on glass as shown on glazing details sheet #8.
         6. Apply face member without preloading gasket.
         7. Roll in glazing gasket HP-10477 on exterior of reglazed lite and bottom side of intermediate horizontal if applicable.




April 2003                                                                                                                                          15
     HP-175/225   INSTALLATION   MANUAL

             DOOR HEAD DETAILS




16                                        April 2003
             HP-175/225   INSTALLATION   MANUAL

                     DOOR JAMB DETAILS




April 2003                                        17
     HP-175/225   INSTALLATION   MANUAL

     BUTT GLAZED MULLION FABRICATION AND
          SHEAR BLOCK INSTALLATION




18                                         April 2003
               HP-175/225   INSTALLATION   MANUAL

                       SEALANT PROCEDURES
                    FOR HEAD, SILL & HORIZONTAL
             BUTT GLAZE MULLION WITH INTEGRAL DIVERTER




April 2003                                               19
     HP-175/225   INSTALLATION   MANUAL

            BUTT GLAZE MULLI0N
             GLAZING DETAILS




20                                        April 2003
             HP-175/225   INSTALLATION   MANUAL

                    BUTT GLAZE MULLI0N
                     GLAZING DETAILS




April 2003                                        21
           HP-175/225   INSTALLATION   MANUAL

     INTEGRAL DIVERTER HORIZONTAL BRIDGE INSTALLATION
                  FOR BUTT GLAZE MULLION




22                                              April 2003
             HP-175/225   INSTALLATION    MANUAL

                    OUTSIDE 90° MULLION
                       FABRICATION




April 2003                                         23
     HP-175/225   INSTALLATION    MANUAL

            OUTSIDE 90° MULLION
                ASSEMBLY




24                                         April 2003
             HP-175/225   INSTALLATION   MANUAL

                     OUTSIDE 90° MULLION
                  DIVERTER & GLAZING DETAIL




April 2003                                        25
     HP-175/225   INSTALLATION   MANUAL

            OUTSIDE 90° CORNER
             OPTIONAL DETAIL




26                                        April 2003
             HP-175/225    INSTALLATION   MANUAL

                            INSIDE 90°
                          CORNER DETAIL




April 2003                                         27
     HP-175/225   INSTALLATION   MANUAL

                OUTSIDE 90°
       BUTT GLAZE MULLION FABRICATION




28                                        April 2003
             HP-175/225   INSTALLATION   MANUAL

                        OUTSIDE 90°
                BUTT GLAZE MULLION ASSEMBLY




April 2003                                        29
     HP-175/225   INSTALLATION   MANUAL

             OUTSIDE 90° MULLION
          DIVERTER & GLAZING DETAIL




30                                        April 2003
             HP-175/225   INSTALLATION   MANUAL

                          INSIDE 90°
                  BUTT GLAZE CORNER DETAIL




April 2003                                        31
     HP-175/225   INSTALLATION   MANUAL

             GLAZING ADAPTOR
               INSTALLATION




32                                        April 2003
             HP-175/225   INSTALLATION   MANUAL

                        SINGLE SPAN
                     WIND LOAD CHARTS




April 2003                                        33
     HP-175/225   INSTALLATION   MANUAL

                SINGLE SPAN
             WIND LOAD CHARTS




34                                        April 2003
             HP-175/225   INSTALLATION   MANUAL

                        SINGLE SPAN
                     WIND LOAD CHARTS




April 2003                                        35
                    HP-175/225                  INSTALLATION                         MANUAL

                                            HORIZONTAL
                                         DEAD LOAD CHARTS

 THESECHARTS REPRESENT 1" GLASSAT 1/4 POINT LOADING AND 1/8 POINT LOADING (SHOWN WITH DOTTED LINE)




36                                                                                                   April 2003
             HP-175/225   INSTALLATION   MANUAL

                   PERIMETER ANCHORAGE




April 2003                                        37
     HP-175/225   INSTALLATION                  MANUAL

                 TWIN SPAN
             WIND LOAD CHARTS
                  DEFLECTION LIMITED TO L/175




38                                                       April 2003
             HP-175/225   INSTALLATION                  MANUAL

                         TWIN SPAN
                     WIND LOAD CHARTS
                          DEFLECTION LIMITED TO L/175




April 2003                                                       39
               HP-175/225                    INSTALLATION                        MANUAL

               GLAZING OPTIONS & ACCESSORIES CHART
                          HP-175 & HP-225
                          * HP-10 GLAZING CLIP REQUIRED FOR ALL VERTICALS AND HORIZONTALS.

     OPTIONAL 1" SYSTEM USING HORIZONTALS WITH INTEGRAL WATER DIVERTERS
      Glass    Interior       Glazing                      Horizontal       Verticle         Setting     Perimeter
                                           Terminator
      Size     Gasket         Adapter                        Clip            Clip            Block        Spacer

      3/16"    NHP-30         HP-119          HP-213           HP-8          HP-10           HP-17       NHP-1003
      1 /4"    NHP-5A         HP-119          HP-213           HP-8          HP-10           HP-17       NHP-1003
      5/16"    NHP-33         HP-119          HP-213           HP-8          HP-10           HP-17       NHP-1003
      9/16"    NHP-30         HP-163          HP-213           HP-8          HP-10           HP-17       NHP-1003
       5/8"    NHP-5A         HP-163          HP-213           HP-8          HP-10           HP-17       NHP-1003
     11/16"    NHP-33         HP-163          HP-213           HP-8          HP-10           HP-17       NHP-1003
     15/16"    NHP-30          ------         HP-213           HP-8          HP-10           HP-17       NHP-1003
        1"     NHP-5A          ------         HP-213           HP-8          HP-10           HP-17       NHP-1003
     1 1/16"   NHP-33          ------         HP-213           HP-8          HP-10           HP-17       NHP-1003




     OPTIONAL 1/4" SYSTEM USING HORIZONTALS WITH INTEGRAL WATER DIVERTERS

      Glass    Interior                     Horizontal       Vertical       Setting
                            Terminator
      Size     Gasket                         Clip            Clip          Block
      3/16"    NHP-30         HP-140           HP-8            HP-8          HP-17
      1 /4"    NHP-5A         HP-140           HP-8            HP-8          HP-17
      5/16"    NHP-33         HP-140           HP-8            HP-8          HP-17




     NOTE: NHP-5A TO BE USED AS EXTERIOR
     GASKET FOR ALL GLAZING INFILLS.

40                                                                                                     April 2003

								
To top