Model No. CE3156 Jumbo Remote Control Features - Universal Remote by ltq93779

VIEWS: 155 PAGES: 2

									Model No. CE3156                                                      Jumbo Remote Control


Features

   -    Universal Remote Control (URC)
   -    Operates with most manufacturers
   -    Operates with TV, VCR, DVD and Satellite
   -    Large Buttons
   -    Teletext function
   -    Requires 2 X AA (LR6) batteries (not included)

Battery Installation

   -    Unit requires 2 X AA (LR6) batteries.
   -    Open the battery cover located at the back of the unit.
   -    Place the batteries in the compartment as indicated by the polarity symbols (+ and -)
        marked inside.
   -    Replace the battery compartment cover until it locks into place.


Manual SET UP Mode

Important

   -    Refer to the attached CODE LIST and look up the appropriate code for your device (TV,
        VCR, DVD or SAT) prior to following the below procedures.
   -    Anytime if you want to leave the Setup Mode, press the DEVICE key or the unit will
        leave the Setup Mode automatically after 10 seconds when no key is been pressed. If
        this happens re-start the procedure from “A”

  A. Power on the desired device (TV, VCR, DVD or SAT). For VCR and DVD turn on the
     device and insert Video tape, CD or DVD.
  B. Press and hold the [SET] button and while holding the [SET] button, press the
     appropriate DEVICE button, e.g. TV, VCR, DVD or SAT.
  C. When the LED light comes on, release both buttons.
  D. Input the appropriate 4 digits brand code for the selected device, which is found in the
     code list.
  E. After inputting the 4 digits code:
          - if the code you have entered is correct the LED light will turn off
          - If the code you have entered is incorrect, the LED will flash twice and keep the
              remote in the setup status. Re-enter the correct number.
  F. If the LED light turns off, press the [POWER] button to check if device (TV, VCR, DVD or
     SAT) switches off.
  G. If the device switches off then the correct code has been stored for that device. Press
     any other function button ([CH+], [CH-], [VOL+], [VOL-] etc.) to test whether the device
     can be controlled.
  H. If the device does not switch off repeat the above procedures with a different code.


QUICK SERCH Mode

The Quick Search option can be used to find out a suitable code for your device when the
correct code is not found from the list or the code is not available for a particular brand device.

   A.       Power on the desired device TV, VCR, DVD or SAT. For VCR and DVD turn on the
            device and insert Video tape or CD/DVD.
   B.       Press and hold the [SET] button and while holding the [SET] button, press the
            selected device button, e.g. [TV], [VCR], [DVD] or [SAT].
   C.       When the LED light comes on, release both buttons.
   D.       Press the [SET] button once more to enter the Quick Search Mode; the LED light
            will continue to flash.
   E.      Aim the URC at your device and repeatedly press the POWER button once or
           twice a second. The URC will send a signal to power off the device. You may have
           to press the [POWER] button up to 200 times until the device response.
   F.      Once the signal is received the device will switch off, stop pressing the [POWER]
           button and press the selected device button (e.g. [TV], [VCR], [DVD] or [SAT]) to
           store the code. The LED light will turn off.
   G.      Press the [POWER] button to switch on the device and to check other controls
           press any other function buttons, i.e. [CH+], [CH-], [VOL+], [VOL-] etc.
   H.      If the device does not respond to the other function buttons, repeat the above
           procedures until the right code is stored.

Remark:
  • THE URC enables you to change the direction of the search to find the code when
     using the Quick Search function. Once you have entered the QUICK SEARCH MODE
     the URC will be set to forward search direction (e.g. 0001, 0002, 0003…). Press the
     SET button once again and the search direction will be set to backward search (e.g.
     0090, 0089, 0088…)
  • Anytime if you want to leave the Quick Search Mode, press the DEVICE key or the unit
     will leave the Quick Search mode automatically after 30 seconds when no key is been
     pressed.


Brand Code Recall

The Brand Code Recall function enables you to recall the 4-digit brand code after the set up is
done OR after the corresponding code number is found by the QUICK SEARCH. Follow the
below procedures to recall the brand code for a particular device:

A. Press the desired device button [TV], [VCR], [DVD] or [SAT], of which you would like to
   recall the code.
B. Press and hold the [SET] button and while holding the [SET] button press number
   [1] button to recall the first digit number of the code, see below example.
C. Release both keys.
D. The number of times that the LED flashes indicates the particular digit number of
   the brand code.

For example :
 Press and hold [SET] button & press [1] button         LED flashes 3 times      the 1st digit
of the code is “3”
  Press and hold [SET] button & press [2] button        LED not flashes      the 2nd digit of
the code is “0”
  Press and hold [SET] button & press [3] button        LED flashes 1 times      the 3rd digit
of the code is “1”
 Press and hold [SET] button & press [4] button         LED not flashes      the 4th digit of
the code is “0”

   The 4-digit brand code is “3010”.

Note: The URC can only recall the last 4 digit code which has been recorded by
the remote control.

								
To top