Docstoc

user manual

Document Sample
user manual Powered By Docstoc
					User Manual
Item No. SPD-M03 Name: Multifunctional Telephone Remote Controller

Index
Chapter1. Brief Introduction for User Manual…………………………………………….. Chapter2. Product Brief Introduction……………………………………………………….. 2.1 Product Brief……………………………………………………………………….. 2.2 Specification & Specialty…………………………………………………………. 3.3 Product Function…………………………………………………………………… Chapter 3. Hardware Installation……………………………………………………………. 3.1 Cable Connection…………………………………………………………………… 3.2 Installation Process…………………………………………………………………. 3.3 Typical Project Installation Drawing………………………………………………. Chapter 4. Initialization Setting…………………………………………………………….. 4.1 Set Output Mode……………..……………………………………………………. Chapter 5. Control Operation……………………………………………………………….. 5.1 Password Checking…………………………………………………………………… 5.2 Control Telephone Line Cable Output State……………………………………………… 5.3 Check Telephone Line Cable Input State…………………………………………………. 5.4 Change Password……………………………………………………………………….. 5.5 Set Operation Voice…………………………………………………………………. 5.6 Back to Initialization Setting…………………………………………………………….. 5.7 Set Point Move Mode Delay Time……………………………………………………… Chapter 6. Item Size & Technical Specifications………………………………………………

Chapter 1 Brief Introduction for User Manual
Item: SPD-M03 Name: Multifunctional Telephone Remote Controller It is possible to connect a wide variety of devices to the relays for example security lights, heating and pump controllers, computers, etc. This remote control/alarm module functions at 1m as well as at 5000 kilometers or anywhere on earth! Commands can be sent to it. All you need is a fixed or mobile phone near you.

Please read this manual carefully before you start to run this device.

Chapter 2 Product Brief Introduction
2.1 Product Brief The telephone control function of the module is very useful for the long distance monitoring of installations or machines being placed at isolated places, such as pomp heaters or generators, for instance. The alarm function can be used for fixed/mobile workshops, building sites, garages, machines, car/truck boats, second homes, etc. Various options can be programmed to it from any telephone; secret access code, timing of alarm, how long the module will call as alarm and eventually a local siren timing with one of the relays, etc. Voice Message will support user for correct and easy work. No need to remember difficulty user manual and count the didi number. Just set the voice user like to take and get the correct state information for the work. 2.2 Specification & Specialty: (1) 1 Output. One channel for output with options for continuous mode & point move mode. More powerful function. (2) Telephone Connector. With the wide telephone network support, user can control instrument at any time & any places and also find out their working state. (3) Voice Message Follow Up. Each operation has the voice message follow up, direct & correct, support user to record his own language for the voice message setting. The alarm call will also send voice message to the user for the state. Forget the difficult didi number count work. (If you need hear light on, say light on, if you need hear switch off, say switch off.) (4) Three times password mistake will arise hang-up automatically. (5) Advanced PCB board setting. Telephone PCB part is divided to the control parts. Safer for the bad weather like thunder. (6) Industrial level 32 digital IC which offer faster and more powerful function.

2.3 Production Function. (1) Remote Control. User can only need dial the telephone to operate his instrument. (For example, turn on or turn off one certain electrical machine’s power.) Chapter 3 Hardware Installation 3.1 Cable Connection 9V Power Adapter 1:Instrument under Control No.1 2:Instrument under Control No.2 Remark: SPD-M03 has only one channel output, no sensor input channel. Telephone Cable Connector RJ11 type Telephone Wire 2:Input No.2 1:Input No.1 3.2 Installation Process (1) Connect the instrument under control’s wire to the output point No.1 (2) Connect the 9V power adapter to the DC 9V place (3) Connect the telephone wire to the telephone connector (4) Check all the wire connection is correct, the under control instrument wire and output point’s wire (5) After wire check, turn on the power for test. The red light on the control board start to flash mean this device start the right work. (6) Dial the telephone and start Initialization. (For example, set the telephone number, shaking ring automatic connecting times, alarm work etc.) 3.3 Typical Project Installation Drawing Telephone wire 2:Input 2 1:Input 1 220V:Alternating Current 220V Input Chapter 4. Initialization Setting 4.1 Set Output Mode System ouput has continuous mode & point move mode. Continuous mode: Output will keep the close or open state Point move mode: After user connect the output, the output place relay close and then open after one second. (The time break can be set between 0.5 seconds to 8 minutes.) After user hear “Control, press 1,” “Check, press 2.” “Setting, press 3” voice message, press 3 and enter the setting process. Then user will hear “Change Password, press 1”, “Set working mode, press 2,” “Set point move or continuous mode, press 3,” “voice record, press 4”. After press 2, user can press 1 or 2 to choose the mode according to voice message “ Continuous mode, press 1,

“ Point move mode press 2.”

Chapter 5 Control Operation 5.1 Password Checking Check Password: Password # After the telephone is connected, user need enter the right password before start the work of the device. After 3 times continuous mistake password enter, system will hang-up automatically. 5.2 Control Telephone Line Cable Output State After user hear “ control, press 1,” “check, press 2,” “Setting, press 3”, follow the step below. (1) Press 1 and start to choose the control function (2) After hear the voice message “ Please choose output channel, exit please press * key”, user press 1 to choose output 1. If user like to set point move mode, user can break the connect after one certain time according to his need. See chapter 5.7. (3) If user set the continuous mode, the voice message will say “Control Output turn on, please press 1,” “Control output turn off, press 0,” “ exit press * key.” Remark: This item has the memory for the output state, after power break accidentally; the system will back to latest state automatically. 5.3 Check Telephone Line Cable Input State After hear “Control press 1, Check press 2, set press 3.” Press 2 enter the check work. Voice message will say “Please enter the check input channel number”, user press 1, system will say “ Input turn on” or “Input turn off” according to real state. 5.4 Change Password After hear “Control press 1, Check press 2, set press 3.” Press 3 enter the change password step. (1) Voice message will be “Change Password press 1, Set work mode press 2, Set point move delay time, press 3, voice record press 4.” (2) Press 1, voice message will be “ Please enter new password and end with # key”. (3) After user enter the new password, voice message will be “Please enter the new password again and end with # key.” If the two times password enter are same, system will accept the new password. Remark: The beginning password is 111111, 6 digital number. When lost password, user can use the reset key on the item to get back to beginning password. The reset key is one small hole on the bottom panel, use one pin thing to press it after 2 seconds, the system will come back to beginning set.

5.5 Set Operation Voice Section No. 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 Please enter password Control press 1, Check press 2, set press 3. Please select output Channel Exit press star(*) key Output connect turn on press 1, Output turn off press 0 Operation Successful Operation Mistake Output turn on Output turn off Press the output number need check Change Password press 1, Set work mode press 2, Set point move delay time, press 3, voice record press 4. Please enter the shaking ring time, 1 to 7 Please enter new password Please enter the new password again End with # key Continuous mode press 1, point move mode press 2 Please enter delay time with # end, number 001 to 999 Welcome to operate SPEED Controller Please enter voice range number Press # for end Voice Message Time (second) 3 5 3 3 5 3 3 3 3 4 9 4 3 3 3 5 7 5 4 3

5.6 Back to Initialization Setting The device has one small hole under the bottom of the box. Use one small pin thing to press it for 2 to 4 seconds and release, the system will back to the initialization mode with voice message. Initialization station: Password: 111111 5.7 Set Point Move Mode Delay Time After hear “Control press1, check press 2, set press 3, follow the step below. (1) Press 3 to enter set work. Voice message “Change Password press 1, Set work mode press 2, Set point move delay time, press 3, voice record press 4. (2) Press 3 and enter to set the point move mode and set delay time. (3) After hear “Please enter delay time with # end, number 001 to 999, Press # for end.”, user enter 3 number fro delay time. (Delay Time is the half of the number entered.)

Chapter 6 Product Size & Specifications 6.1 Item Size & Package: Size:160mm(L)*110mm(W)*410mm(H) Package: 215mm(L)*180mm(W)*50mm(H) 6.2 Technical Specifications: Power Supply: DC9V Current Consumption: <3W Power Supply: AC220V Current: 3A Working Temperature: -20C to + 60C


				
DOCUMENT INFO
Shared By:
Tags: user, manual
Stats:
views:267
posted:12/18/2009
language:English
pages:6
Description: user manual