How to Program your One For All® remote Models URC 2086 URC 7086 Set Up After getting the proper codes from your manual or Customer Service use the following instructions to enter them into yo by dfffwwwkdfi

VIEWS: 435 PAGES: 4

									                                       How to Program your
                                       One For All® remote
                                                (Models URC-2086 URC-7086)

                                                            Set Up
                                 After getting the proper codes from your manual or Customer
                                 Service, use the following instructions to enter them into your
                                 remote.

                                 Your remote will set up in one of the following ways.

                                                Option 1 (Set up #1)
                                1. Press the device you want to program, then release.
                                2. Press A, then B, then C.
                                3. Enter your 3 digit code.
                                4. You should receive 2 quick flashes after entering your code.
                                If your remote sets up like above, follow below for more instructions.

                  Set Up                             Then press:
                                                     DEVICE 1 - A - B - C - SET UP CODE
After getting the proper codes from your
                                                     Example: Let's change the Cable button to a
manual or Customer Service, use the following
                                                     TV button.
instructions to enter them into your remote.
                                                     A - B - C - 9 - 9 - 9 - CABLE - TV
1. Press the device you want to program, then
                                                     We can then assign a TV to the Cable button.
    release.
                                                     CABLE - A - B - C - 017
2. Press A, then B, then C.
3. Enter your 3 digit code.
4. You should receive 2 quick flashes after              Clearing Out A Device Button
    entering your code.
                                                     Press A - B - C - 9 - 9 - 9 - DEVICE KEY -
                                                     DEVICE KEY.
      Reading The Blink Code                         Example: A - B - C - 9 - 9 - 9 - TV - TV
Press A - device (i.e. TV,VCR,etc),
Then press 1 and count the blinks on the
remote (1st digit),                                     Advanced Functions & Key Mover
Press 2 and count the blinks (2nd digit).
Press 3 and count the blinks (3rd digit).            Many devices have advanced functions. In
NO BLINKS = 0                                        order to duplicate those functions you need to
These three numbers make up your setup               find the correct code to send that function to
code.                                                your device. When you have found the code,
                                                     you can access the function either directly or
                                                     through Key Mover.
    Redefining A Device Button
The remote allows the user to assign a TV to                        Direct Access
the VCR or CABLE button.                             Press the DEVICE button
You can assign any combination of devices to         Press the A button
different buttons.                                   Press the three digit code for the function
Press A - B - C - 9 - 9 - 9 - DEVICE 1 -             The function will operate on your device.
DEVICE 2                                             Example: TV - A - 652 is "enter" on a Sony TV.
                Key Mover                                             Set Up
Key Mover allows you to put an advanced            After getting the proper codes from your
function on a key so you just have to hit that     manual or Customer Service, use the following
key to access the function.                        instructions to enter them into your remote.
Press A - B - C - 9 - 9 - 9                        1. Press the device you want to program, then
Press the key you want the function on.                release.
Press A - three digit function code.               2. Press and hold the "A" button until the red
Example: TV - A - B - C - 9 - 9 - 9 - PLAY - A -       LED gives a delayed blink.
652.                                               3. Continue holding the "A" button while you
This would put the "enter" function for that           enter your 3 digit code.
Sony TV on the PLAY button.                        4. You should receive 2 quick flashes after
You should NOT put advanced functions on               entering your code.
the DEVICE keys(i.e. TV,VCR,CABLE,etc.)
You can clear a function off a key by pressing:               Getting Your Code
A - B - C - 9 - 9 - 9 - KEY - KEY.                 If you forget your code, the One For All ® will
                                                   tell you using these simple instructions.
             Punch Through                         1. Press the DEVICE (i.e.TV,VCR,etc) key
Punch Through allows you to operate functions           that you want the code for - release.
from one device while using another                2. Press "A" and hold it down - you will see
one. For instance- if your are using a VCR with         two blinks. Continue to hold down "A"
out volume- you can get the TV volume without      3. While still holding "A", press the Device
changing devices keys. Use this procedure to            button, then press the "1" button. Count the
Punch Through a function:                               number of time the remote blinks.
1. Press the DEVICE button you want the            4. Still holding "A", press the "2" button. Count
    function on.                                        the blinks.
2. Press A - B - C - 9 - 9 - 9 - the DEVICE you    5. Still holding "A", press the "3" button. Count
    want -the Function you want .                       the blinks.
3. The green light will blink twice.               6. Release "A".
(i.e. To get the volume from the TV in the         NOTE: If the remote DOES NOT blink on one
CABLE mode: TV - A - B - C - 9 - 9 - 9 -           of the steps- it means the number is "0".
CABLE - VOLUME+)                                   The three numbers you have make up the set
                                                   up code of your device.
          Option 2 (Set up #2)
                                                           Changing Device Keys
1. Press the key for the                           Suppose you want your One For All® to control
    device(i.e.TV,VCR,etc.) you want to            a second TV?
    program.                                       You can turn the AUX key in to a TV key using
2. Press and hold the "A" button. You will see     the following procedure:
    two blinks. continue to hold the "A"           1. Press the AUX key and release
    button.                                        2. Press "A" (release) 9 - 9 - 9 - AUX - TV.
3. While holding the "A" button, Press the         Your AUX key is now ready to be programmed
    three digit set up code.                       with your TV code using the set up instructions.
    You will see two blinks on the remote.
4. Release the "A" button.                         You can change any of the device keys using
If your remote sets up like above, follow below    this same method.
for more instructions.
          Volume Punch Through                                              Option 3 (Set up #3)
If you would like to access the TV volume                         1. Press the key for the
through the CABLE key for convenience,                                device(i.e.TV,VCR,etc.) you want to
you would use the following procedure:                                program.
1. Press the "CABLE" key, release.                                2. Press and hold the "A" button- you will see
2. Press "A" (and release)                                            a blink ad then two quick blinks on the
3. Press 9 - 9 - 9 - TV - VOLUME +                                    remote.
You should now get volume in the CABLE                                Release the "A" button..
mode.                                                             3. press the 3 digit set up code
You can punch through volume to VCR's using the same procedure.       You will see two blinks on the remote.
                                                                  If your remote sets up like above, follow below
             Advanced Functions                                   for more instructions.
You can access advanced functions for your
equipment using one of these two procedures.                                           Set Up
Direct Access                                                     After getting the proper codes from your
1. Find the three digit code for the advanced                     manual or Customer Service, use the following
   function you want.                                             instructions to enter them into your remote.
2. Press "A" (and release) and the three digit                    1. Press the device you want to program, then
   code.                                                              release.
3. The function you desired will be performed                     2. Press and hold the Magic button until the
   on your device.                                                    red LED flashes twice, then release.
Key Magic                                                         3. Enter your 3 digit code.
You can put the function on a key so you can                      4. You should receive 2 quick flashes after
access it with one stroke!                                            entering your code.
1. Find the three digit code for the advanced
    function you want.                                                   Blinking Back the Code:
2. Press "A" (and release).                                       1.   Tap the device Key - Release
3. Press 9 - 9 - 9 -                                              2.   Hold "Magic" until it blinks twice - release.
4. Press the button you want the function on.                     3.   Press 9 - 9 - 0.
5. Press "A" (and release).                                       4.   Press 1, Count the number of blinks. (1st
6. Press the three digit code for the function                         digit)
    you want.                                                     5. Press 2, Count the number of blinks. (2nd
7. You will see two(2) blinks on the remote.                           digit)
Now whenever you hit that key, the function                       6. Press 3, Count the number of blinks. (3rd
will be performed on the device.                                       digit)
                                                                  If the remote DOES NOT blink it means the
              Clearing Out a Key                                  number is 0.
If you decide to change something you have
put on a key, it is as simple as following these                               Redefining a Key
instructions.                                                     1. Hold "Magic" Until it blinks twice.
1. Press the Device key of the key you want to                    2. press 9 - 9 - 2.
    clear. (i.e. TV for TV volume)                                3. press the DEVICE key you want moved
2. Press the "A" key (and release).                               4. press the DEVICE key you want to replace.
3. Press 9 - 9 - 9 -                                              Example: If you want the Aux key to be a TV
4. Press the key you want to clear two (2)                        key:
    times.                                                        "MAGIC" (2 blinks) 9 - 9 - 2, TV (you want to
5. You will see two blinks on the remote.                         move TV)
                                                                  Then AUX (you want to replace AUX).
Now the key is set back to its original
function.
              Punch Through                        From One Button to Another
This sets Volume to work for one device in all     1. Hold "Magic" until it blinks twice - release.
modes.                                             2. Press 9 - 9 - 4.
For example, the TV volume will work in the        3. Tap the DEVICE and the FROM button
cable and VCR modes.                               4. Tap the DEVICE and the TO button
1. Hold "MAGIC" until it blinks twice - release.   5. Two Blinks
2. Press 9 - 9 - 3.                                EXAMPLE: To take the volume from a TV and
3. Press the device key you would like the         put it in the VCR mode,
    volume to come from.                           it would be: MAGIC - 9 - 9 - 4 - TV - VOL UP -
You will get two blinks on the remote.             VCR - VOL UP - two blinks.
If you want to set the volume for a device to      You would have to do the same process for
work just one or two other devices- refer to the   VOL DN and MUTE.
instructions under "KEYMOVER-From one
button to another"

              Volume Default
Use this to get Cable or VCR volume to work.
1. Hold Magic until it blinks twice - release.
2. Press 9 - 9 - 3
3. press the VOLUME key, you will get two
   blinks.
Now The volume is set for all original devices.

                Clearing Out
     A Device Key - Or Another Button
1.   Tap the device Key - release.
2.   Hold Magic for Two blinks - release.
3.   Press 9 - 9 - 2
4.   Press the button twice. - Two blinks.
 All Key movers,Macro's, and Defaults
1. Tap the device Key - release
2. Hold "Magic" for two blinks - release
3. Press 9 - 8 - 0 -- Two blinks.

                  Key Mover
An Extended Function To A Button
1. Tap the DEVICE key - Release.
2. Hold "Magic" for two blinks - release.
3. Press 9 - 9 - 4.
4. Tap the "Magic" button and then the tree
   digit extended function.
5. Tap the button you wish to use for that
   function - Two Blinks.

								
To top