FM2203

SECTION: 2.40.060 FM2203 0207 Supersedes 0606 MAIL TO: P.O. BOX 16347 • Louisville, KY 40256-0347 SHIP TO: 3649 Cane Run Road • Louisville, KY 40211-1961 (502) 778-2731 • 1 (800) 928-PUMP • FAX (502) 774-3624 Product information presented here reflects conditions at time of publication. Consult factory regarding discrepancies or inconsistencies. visit our web site: www.zoeller.com COMPARE THESE FEATURES • FM and cCSAus rated Class 1, Division 1, Group C & D. Not for use in acidic atmospheres. • Non-Clogging semi-open ductile iron impeller. • Class 30 cast iron construction. • All units are double seal for extra motor protection. • Corrosion resistant powder coated epoxy finish. • Stainless steel screws, washers, tags and seal assembly. • 25 foot UL Listed power and sensor cord. Cord length also available in 50 foot. • Single phase - 230V capacitor start, capacitor run. • Three Phase - 200-230-460-575 Volt. • Explosion proof motor - 60 Hz, 1750 RPM, oil-filled, hermetically sealed with heavy duty finned motor housing for added heat dissipation. • Thermal sensor. • Continuous duty operation in submerged conditions. • Maximum temperature for sewage or dewatering 104°F (40°C) with 1.2 service factor (1.0 service factor on Model 661). • 416 stainless steel motor shaft. • Tandem shaft seals - stainless steel fitted, carbon/ceramic seal faces. • Seal leak probes. • Oversized upper & lower ball bearings running in an oil bath. • Buna-N square rings and seals used throughout. • All models pass 2½" spherical solids. • Specify 3" NPT vertical, 3" horizontal flanged or 4" horizontal flanged discharge. • 100% computerized tested. • Major width 17 9/16". Height 33 ¼". • Non-sparking rail systems available for all models. • Intrinsically safe control panels available. X600 SERIES HAZARDOUS ENVIRONMENT SERIES CLASS 1, DIVISION 1, GROUP C & D, 1 - 7½ HP / 1750 RPM X611 X621 X631 X641 X651 X661 1.0 HP 1.5 HP 2.0 HP 3.0 HP 5.0 HP 7.5 HP (For Pump Prefix Identification see News & Views 0052) “SEWAGE-WASTE” SUBMERSIBLE SEWAGE OR DEWATERING NON-CLOG PUMP Certified to CSA Standard C22.2 No. 145 Standard 3600 & 3615 3" Vertical Discharge 3" & 4" Horizontal Discharge MODELS AVAILABLE Manufacturers of . . . • Nonautomatic (for intrinsically safe variable level control systems). • Double seal only. • 3" Vertical, 3" Horizontal or 4" Horizontal flanged discharge. • 230V/1 Phase or 200/230/460/575V/3 Phase. © Copyright 2007 Zoeller Co. All rights reserved. 1 METERS FEET PUMP PERFORMANCE CURVE MODELS X611/X621/X631/X641/X651/X661 70 20 65 60 55 16 50 14 45 40 35 10 30 8 25 20 15 4 10 2 5 X661 X611 50 GALLONS LITERS 0 400 800 1200 FLOW PER MINUTE 1600 2000 2400 100 150 200 250 300 X621 350 X631 400 450 X641 500 550 X651 600 650 MODEL Feet Meters 5 1.5 10 3.0 15 4.6 20 6.1 25 7.6 30 9.1 35 10.7 40 12.2 45 13.7 50 15.2 55 16.7 60 18.2 Shut-off Head: X611 Gal. Liters 255 965 190 719 110 416 35 132 ----------------22 ft.(6.7m) X621 Gal. Liters 340 1287 277 1048 215 813 143 541 72 272 --------------29 ft.(8.8m) 013859X X631 Gal. Liters 385 1457 330 1249 275 1040 220 832 150 567 80 302 ------------35 ft.(10.7m) X641 Gal. Liters 480 1816 430 1627 380 1438 325 1230 270 1022 208 787 143 541 72 272 --------44 ft.(13.4m) X651 Gal. Liters 575 2176 533 2017 490 1854 440 1665 390 1476 335 1268 280 1059 220 832 150 568 80 302 ----55 ft.(16.8m) X661 Gal. Liters --600 2271 560 2119 515 1949 475 1798 430 1627 383 1449 330 1249 280 1059 220 832 150 568 85 321 65 ft.(19.8m) 18 TOTAL DYNAMIC HEAD 12 6 0 Standard all models - 25 ft. cord - 1.0 HP X611 Models *EX611 JX611 FX611 GX611 BAX611 Volts 230 200 230 460 575 Phase 1 3 3 3 3 Mode Nonauto Nonauto Nonauto Nonauto Nonauto Amps 6.9 4.3 3.7 1.9 1.6 X641 Models *EX641 JX641 FX641 GX641 BAX641 Standard all models - 25 ft. cord - 3.0 HP Volts 230 200 230 460 575 Phase 1 3 3 3 3 Mode Nonauto Nonauto Nonauto Nonauto Nonauto Amps 17.0 11.0 9.6 4.8 3.9 Standard all models - 25 ft. cord - 1.5 HP X621 Models *EX621 JX621 FX621 GX621 BAX621 Volts 230 200 230 460 575 Phase 1 3 3 3 3 Mode Nonauto Nonauto Nonauto Nonauto Nonauto Amps 8.9 5.9 5.1 2.6 2.0 X651 Models *EX651 JX651 FX651 GX651 BAX651 Standard all models - 25 ft. cord - 5.0 HP Volts 230 200 230 460 575 Phase 1 3 3 3 3 Mode Nonauto Nonauto Nonauto Nonauto Nonauto Amps 28.0 17.5 15.2 7.6 6.1 Standard all models - 25 ft. cord - 2.0 HP X631 Models *EX631 JX631 FX631 GX631 BAX631 Volts 230 200 230 460 575 Phase 1 3 3 3 3 Mode Nonauto Nonauto Nonauto Nonauto Nonauto Amps 12.0 7.8 6.8 3.4 2.7 X661 Models JX661 FX661 GX661 BAX661 Standard all models - 25 ft. cord - 7.5 HP Volts 200 230 460 575 Phase 3 3 3 3 Mode Nonauto Nonauto Nonauto Nonauto Amps 25.3 22.0 11.0 9.0 *All single phase units require external starting capacity and relay circuits. For information on additional Zoeller products refer to catalog on Variable Control Switches, FM0526; Control Panels, FM1705; Sump/Sewage Basins, FM0487; Rail Systems, FM0787. All installation of controls, protection devices and wiring should be done by a qualified licensed electrician. All electrical and safety codes should be followed including the most recent National Electrical Code (NEC) and the Occupational Safety and Health Act (OSHA). For unusual conditions a reserve safety factor is engineered into the design of every Zoeller pump. © Copyright 2007 Zoeller Co. All rights reserved. RESERVE POWERED DESIGN 2 3” Flanged Discharge Weight 245 lbs. 3” Vertical Discharge Weight 245 lbs. BASIN SIMPLEX DUPLEX DIAMETER 30 INCH MINIMUM 36 INCH MINIMUM FOR SIZE ONLY. VOLUME MAY REQUIRE LARGER BASIN. BASIN DIAMETER SIMPLEX 24 INCH MINIMUM DUPLEX 30 INCH MINIMUM FOR SIZE ONLY VOLUME MAY REQUIRE LARGER BASIN 6 5/16 3"-8 NPT 6 5/16 O T N I T A I T O A T N 9 5/8 15 15/16 15 1/8 SIMPLEX INSTALLATION ALL DIMENSIONS IN INCHES UNLESS OTHERWISE NOTED ø.48 3 INCH UNICHECK P/N 30-0160 3 INCH NIPPLE (BY OTHERS) 3 INCH-8 NPT FLANGE (BY OTHERS) 10 3/4 9 1/8 17 9/16 SIMPLEX INSTALLATION ALL DIMENSIONS ARE IN INCHES UNLESS OTHERWISE NOTED DIAMETER .68 .96 FLA <20 >20 ø.48 WEEP HOLE 33 1/4 3 INCH CHECK VALVE P/N 30-0160 5 1/4 WEEP HOLE STANDARD 3 INCH 90° FLANGED ELBOW (BY OTHERS) 2 5/8 8 5/16 5 1/4 ZEPA0547A 4” Horizontal Discharge Weight 245 lbs. ø .48 FLA <20 >20 DIAMETER .68 .96 4 INCH CHECK VALVE P/N 6030-0203 T I O 33 1/4 5 1/4 N 11 3/4 11 17 5/16 17 5/8 SIMPLEX INSTALLATION STD. 4 INCH-90° ELBOW P/N 6030-0194 2 5/8 FOR 2 1/2" SOLID HANDLING 3 1/8 FOR 3" SOLID HANDLING ALL DIMENSIONS IN INCHES UNLESS OTHERWISE NOTED © Copyright 2007 Zoeller Co. All rights reserved. 3 R O R O T A R O FLA <20 >20 DIAMETER .68 .96 33 1/4 2 5/8 ZEPA0548A BASIN SIMPLEX DUPLEX DIAMETER 30 INCH MINIMUM 48 INCH MINIMUM FOR SIZE ONLY. VOLUME MAY REQUIRE LARGER BASIN. 6 5/16 ZEPA0549A NON-SPARKING RAIL SYSTEM DIMENSIONAL DATA 3” Vertical 39-0076 BASIN DIAMETER SIMPLEX 30 INCH MINIMUM DUPLEX 36 INCH MINIMUM FOR SIZE ONLY. VOLUME MAY REQUIRE LARGER BASIN. 6 5/16 22 5/8 3” Horizontal 39-0095 42 INCH DIAMETER MINIMUM FOR SIZE ONLY. VOLUME MAY REQUIRE LARGER BASIN. DOOR FRAME REF. PLANE 25 1/4 6 5/16 N 27 1/8 T T A I O T I O N T I O N 9 1/8 15 7/16 17 13/16 25 3/4 SIMPLEX INSTALLATION DOOR FRAME REF. PLANE TWO 3/8 HOLES 1 1/2 3 1/4 FLA DIAMETER <20 .68 >20 .96 15 15/16 LIFTING CABLE S.S. OR GALV. STL. (OPTIONAL) CABLE CONNECTOR S.S. OR GALV. STL. (OPTIONAL) SIMPLEX INSTALLATION DOOR FRAME REF. PLANE LIFTING CABLE S.S. OR GALV. STL. (OPTIONAL) DUPLEX INSTALLATION DIMENSIONS BASED ON STANDARD ANSI FITTING SIZES CHECK VALVES REQUIRED, NOT SHOWN FOR CLARITY ALL DIMENSIONS IN INCHES UNLESS OTHERWISE NOTED CABLE CONNECTOR S.S. OR GALV. STL. (OPTIONAL) FLA <20 DIAMETER .68 TWO 1/2 HOLES 3/4 INCH S.S. OR GALV. STL. PIPE (BY OTHERS) 3 INCH UNICHECK P/N 6030-0160 3 INCH NIPPLE (BY OTHERS) WEEP HOLE 3 INCH COUPLING (BY OTHERS) 3 INCH MALE NPT 3/8 3 3/8 ø .48 LIFTING HEIGHT = 44 (WITHOUT CABLE CONNECTOR) LIFTING HEIGHT = 47 (WITH CABLE CONNECTOR) 3 2 INCH S.S OR GALV. STL. PIPE (BY OTHERS) 9 5/8 ø.48 LIFTING HEIGHT = 45 1/4 (WITHOUT CABLE CONNECTOR) (WITH CABLE CONNECTOR) >20 .96 34 11/16 3 INCH UNICHECK P/N 6030-0202 36 4 1/16 6 11/16 2 1/2 - 3 INCH HOR. RAIL SYSTEM 5/8 14 1/8 30 1/8 8 5 3/8 LIFTING HEIGHT = 47 1/2 ZEPA0550A 4” Horizontal 39-0017 36 INCH DIAMETER MINIMUM FOR SIZE ONLY. VOLUME MAY REQUIRE LARGER BASIN. DOOR FRAME REF. PLANE 24 3/4 60 INCH DIAMETER MINIMUM FOR SIZE ONLY. VOLUME MAY REQUIRE LARGER BASIN. T I O N 17 1/8 T I O N 12 5/8 R O 26 38 3/8 T I O N 20 LIFTING CABLE S.S. OR GALV. STL. (OPTIONAL) CABLE CONNECTOR S.S. OR GALV. STL. (OPTIONAL) SIMPLEX INSTALLATION DOOR FRAME REF. PLANE 5 1/16 ø.1/2 - 2 HOLES 1 2" GUIDE RAIL (BY OTHERS) 5 7 DUPLEX INSTALLATION DIMENSIONS BASED ON STANDARD ANSI FITTING SIZES CHECK VALVES REQUIRED, NOT SHOWN FOR CLARITY ALL DIMENSIONS IN INCHES UNLESS OTHERWISE NOTED ø.48 2 LIFTING HEIGHT = 44 1/8 (WITHOUT CABLE CONNECTOR) 4 INCH CHECK VALVE P/N 6030-0203 13 5/64 4 INCH-125 LB ANSI FLANGE 34 1/2 3/4 12 30 3/8 1 5/64 6 1/2 3 3/8 3 7/8 FOR 2 1/2" SOLID HANDLING PUMPS FOR 3" SOLID HANDLING PUMPS LIFTING HEIGHT = 46 3/4 (WITH CABLE CONNECTOR) FLA <20 >20 DIAMETER .68 .96 REFERENCE VIEW OF LIFTING LUGS ZEPA0552B © Copyright 2007 Zoeller Co. All rights reserved. 4 R O T A 9 5/8 T I O N R O 14 1/2 R O T A R O R O R O T T A A T A T A ZEPA0551B ZEPA0570