一、 by csgirla

VIEWS: 53 PAGES: 11

More Info
									RFID Card Access Control
Manual__R300B

1

1.

Product Specification
I tem Speci fi ca ti on 1 2 VDC + 10 %, Cu rren t 1 .2 A 1 2 VDC/ 2 A worki n g :0 ℃~4 5 ℃; s t orage: -1 0 ℃~5 5 ℃ worki n g :4 0 %~9 0 %RH; s t orage: -2 0 %~9 0 %RH

Volt a ge Lock Re la y En vi ron men t al Temp erat u re

Relat i ve h u mid i t y

Card Cap aci t y PIN Cap aci t y In t ern al Read er Freq u en cy Prox i mi t y Card Card Read i n g Di s t an ce Lock i n t erface Ex i t Bu t t on Bell Door C on t act

500 Pu b li c PIN:1 Pri vat e PIN: 5 0 0 ID m od el:1 2 5 KHz ICmod el :1 3 .5 6 M Hz ID m od el: EM or comp at i b le IC mod el : Mi fare 1 or c omp at i b le ID m od el:5 - 1 5 CM IC mod el :3 - 5 CM Rela y ou t p u t or level ou t p ut On e i nt erface On e i nt erface On e i nt erface

2

Alarm In t erface Ex t ern al Read er

On e level ou t p u t On e wei gan d 2 6 in t erface (On l y ap p ly t o cert ai n mod els )

2.

Factor y Defaults
I tem Va l ue 9 9 01 01 Card or p ub li c p in ( 12 34 ) 0 0 00 3 s econd s Di s ab led Di s ab led Di s ab led 0 s econd s Di s ab led

Programmi n g PIN Door Op en Mod e Pri vat e PIN Door Op en Ti me An t i -Break Alarm Door C on t act Alarm Lock St at u s Alarm De la y Mod i fy Pri vat e P IN

3. The LED an B uzzer 3.1. Normal mode: 3.1.1. Valid command: Short beep 3.1.2. Invalid command: Long beep 3.2. Programming mode: 3.2.1. Green LED on 3.2.2. Valid command: Two short beeps 3.2.3. Invalid command: Three beeps 3

4. 5. 5.1.

Cancel Command Press the [ *] key to cancel command. Functions and Setup Enter the programming mode

Press [ *] +[6-digit pin] (Default is 990101) 5.2. Modify the programming pin Press [0] +[new 6-digit pin] +[confirm the new 6 -digit pin] 5.3. Enroll card Press [5] +[3-digit index code] (2 beeps) +[Card1] (beep, 2 beeps) +[Card2] (beep, 2 beeps) +…… +[Cardn] (beep, 2 beeps) +[ *] (2 beeps) 5.3.1. 3-digit index code: range from 001-500. Card can be deleted by this code. 5.3.2. When enrolling multiple cards, every card index code will be calculated in order. For example, card one’s index 4

5.3.3.

code is 15, card two’s will b e 16. The default private pin for each card is 0000

5.4. Delete card 5.4.1. Delete by index code Press [7] +[3-digit code1] (2 beeps) +[3-digit code2] (2 beeps) +…… +[3-digit coden] (2 beeps) +[ *](2 beeps) 5.4.2. Delete by presenting card Press [7] +[Presenting Card1] (bee p, 2 beeps) +[Presenting Card2] (beep, 2 beeps) +…… +[Presenting Cardn] (beep, 2 beeps) +[ *] (2 beeps) 5.4.3. Delete all cards Please restore the factory default 5.4.4. The private pin will be deleted when the card is deleted 5.5. Exit programming mode Press [ *] (2 beeps) 5

5.6. Set up door open mode 5.6.1. Card or pin mode Press [1]+[0] (2 beeps) 5.6.2. Card + private pin mode Press [1]+[1] (2 beeps) 5.7. PINs The pin in “Card or PIN” mode is either the public pin or private pin (at most 500). 5.7.1. Disable changing private pin Press [1]+[2] (2 beeps) 5.7.2. Enable changing private pin Press [1]+[3] (2 beeps) 5.7.3. Change private pin Press [# ] (2 beeps) +[Presenting card ] (beep,2 beeps) +[4-digit old pin ] (2 beeps) +[4-digit new pin ] +[confirm the new pin ] (2 beeps) 5.7.4. Change public pin Press [3]+[4-digit pin] (Default 1234) When the public or private pin is 0000, the pin is void in “Card or pi n” mode. 5.8. Change door open time Press [2]+[TT] TT is the time interval in seconds. For 6

example, if the door open time is 3 seconds, then TT=03. 5.9. Anti-break 5.9.1. Disable anti -break: Press [4]+[0] 5.9.2. Enable anti-break: Press [4]+[1] 5.10. Door contact sensor 5.10.1. Disable door sensor: Press [6]+[0] 5.10.2. Enable door sensor: Press [6]+[1] 5.11. Door sensor alarm 5.11.1. Disable alarm: Press [8]+[0] 5.11.2. Enable alarm: Press [8]+[1] After turning on this function, the controller will give off continuous long beep when the door is not closed after normal opening, or the door is not opened through the controller. 5.12. Alar m delay ti me Press [82]+[TT] . TT is the time interval in seconds. For example, if the delay time is 3 seconds, then TT=03. When door is locked TT seconds, if the door contact sensor is in alarm st atus, the controller is in alarm mode. This function should be used when the door sensor alarm is on. 7

6.

Restore factor y default Press [86]. There will be 2 beeps, 3 beeps and 3 beeps after 5 seconds, then

the factory defaults are restored. 7. User ’s instructio n 7.1. Card or PIN mode 7.1.1. The pins should be entered in 2 seconds 7.1.2. Press [ *] key to cancel pin input 7.2. Card + Private PIN mode 7.2.1. [Reading card] +[enter 4-digit pin] to open 7.2.2. Press [ *] key to cancel pin input 8. Reset programming pin Short the J2 on controller to reset th e programming pin to factory default 9. Frequentl y asked questions
Pos s i b le s olu t i ons Th e con t roller n eed s hi gh er vo lt age; t h e p ower s u p p ly s h ou l d b e ch ecked . 1 . If t h e con t roller i s on met al s u rface, i t sh ou ld b e moved to ot h er p lace.

S ymp t om Aft er t h e lock i s op en ed , t h ere are 8 sh ort b eeps Th e card read in g d i st an ce i s s h ort or card can n ot b e

8

read Aft er read i n g card , t h ere are 3 b eep s an d lock i s n ot op en Th e en rolled card can n ot op en t h e d oor Pres s [ *]+ [Programmi n g p i n ] th ere is lon g b eep and can n ot en t er the p rogrammi n g mod e Pres s [ # ] key, t h ere i s a lon g b eep , t h e p ri vat e pin can n ot be ch an ged Pres s [5 ],th ere are 3 b eep s Pres s [5 ]+ [i nd ex cod e], 3 b eep s Pres s [5 ]+ [i nd ex cod e] 2 b eep s + [p res en ti n g card ] 3 b eep s

2 . Ch eck th e p ower su pp l y. 1 . It ’s in card+ pi n mod e. 2 . [# ] key i s p res s ed , wait for 5 s econ d s t o p res en t t h e card . 1 . Ch eck i f t h e d oor s en s or i s in alarm s t at us . 2 . Di s ab le t h e d oor s en s or alarm. Ot h er keys are p ress ed b efore p res si n g th e [ *] ke y. Keep o n p res si n g [*] ke y a ft er lon g b eep , t h en ent er t h e p rogrammi n g mode agai n .

Ot h er keys are p ress ed b efore p res si n g th e [ *] ke y. Keep o n p res si n g [*] ke y a ft er lon g b eep , t h en p ress th e [ *] ke y a gai n . Th e con t roller h as fu ll car d cap aci t y. Th i s i nd ex cod e is i n us e, s elect an ot h er in d ex cod e. Th i s card i s i n u s e.

9

Th e con t roller ex i t p rogrammi n g mod e

In p rogrammi n g mod e, i f t h ere is n o i np ut in 2 0 s econ ds , the con t roller ex i t s p rogramming mod e au t omati call y.

10. Wiring 10.1. With normal power supply
DOOR DG ND POENSW PUSH/ NO NC G ND + 1 2 VDC BE LL BE LL J P3 J P2 To ex i t bu tt on To G ND o f t h e fai l -s a fe l ock To G ND o f t h e fai l -op en lock To t h e G ND of p ower s u pp l y To t h e + 12 V of p ower s u pp l y To d oor b el l To d oor b el l Sh ort J P3 Sh ort 1 ,2 Th e ot h er DG ND en d to To d oor con t act Th e ot h er DG ND en d to

Th e ot h er end off t h e loc k t o + 1 2 VDC Th e ot h er end off t h e loc k t o + 1 2 VDC

10

10.2. With access control power sup ply
DOOR DG ND POENSW PUSH/ NO To ex i t bu tt on To PUSH on p ower s u pp l y Th e ot h er end t o DG ND Lock s h ou ld b e wi red t o p ower s u p p ly’s NC and G ND. To con t act d oor Th e ot h er end t o DG ND

NC G ND + 1 2 VDC To t h e G ND of p ower s u pp l y To t h e +1 2 V of p ower s u pp ly To d oor b el l To d oor b el l Do NO T s h ort J P3 Sh ort 2 ,3

BE LL BE LL J P3 J P2

11


								
To top