Docstoc

Cameron Micro Drill Presses

Document Sample
Cameron Micro Drill Presses Powered By Docstoc
					                                                                                 Micro Drill Presses
                                                                                   a division of Treat Enterprises, Inc.

  19401 Rawhide Road • Sonora, CA 95370 • Phone: 209-532-7201 • Fax: 209-532-1211




 Cameron Series 164
 Micro Drill Press

  The Cameron Series 164 Micro Drill Press
  is used for a wide range of precision
  drilling applications such as:
  •	Printed	Circuit	Boards
  •	Laboratory	R	&	D
  •	Prototype	Applications


  Features:
  •	 Single	Speed	Motors	with	Three	Spindle	Speeds	of	9,500	•	17,000	•	30,000	
     RPM	(Optional	Speed	Controls	are	available	for	lower	RPM	settings)
  •	 Smooth	Rack	and	Pinion	Feed
  •	 DRILLS	SMALL	HOLES	FROM	.002"	TO	5/32"	AND	TO	THE	CENTER	OF	A	5"	
     WORKPIECE
  •	 SPINDLE	RUNOUT	AT	CHUCK	MOUNTING	TAPER	IS	WITHIN	.0001"
  •	 Spindles,	pulleys	and	motors	are	dynamically	balanced	for	smoothness	in	
     operation
  •	 Clear	plastic	safety	guard	for	easy	viewing	of	belt	and	pulley	position.
  •	 Slotted	4"	x	4"	work	table	with	5/8"	center	hole
  •	 Made	in	the	USA

  Options:
  •	 Variable	Speed	Control	for	International	and		
     Domestic	use	240/120	V.	AC	(5	amp)
  •	 Foot	Operated	On/Off	Switch
  •	 Jacobs	5/32"	keytype	chuck	w/key
  •	 Albrecht	0-1/8"	or	0-1/16"	capacity	precision	keyless	chucks
  •	 4	Yukiwa	0-1/8"	capacity	precision	keyless	chuck
  •	 Precision	ground	reservoir	bases
  •	 Hollow	spindles	for	special	applications
  •	 Table	column	stop                                                                                  Cameron
  •	 Dial	indicators	1/2"	travel	&	A.G.D.	standard	lug	back                                            Series 164
  •	 Chuck	wedges	for	easy	&	safe	removal	from	taper                                             Micro Drill Press




1-800-369-7769 • www.cameronmicrodrillpress.com
Cameron MD-70 Deep Throat
Micro Drill Press
 •	 The	Cameron	MD-70	Deep	Throat	will	drill	to	the	center	of	a		
    16"	workpiece.	Distance	from	the	spindle	center	to	edge	of		
    supporting	columns	is	8"
 •	 Spindle	runout	at	mounting	taper	is	within	.0001"
 •	 Working	area	of	drilling	table	6-7/8"	wide	by	11-3/8"	deep
 •	 Single	Speed	Motor	with	3	spindle	speeds	of	9,500	•	17,000	•	30,000	
    RPM	(Variable	Speed	Control	available	for	lower	RPM	settings)
 •	 Drills	small	holes	from	.002"	to	5/32"
 •	 Maximum	distance	from	chuck	jaws	to	work	table	is	5	inches
 •	 Spindles,	pulleys	&	motors	dynamically	balanced	for		
    smoothness	in	operation
 •	 Clear	plastic	safety	guard	for	easy	viewing		
    of	belt	and	pulley	position
 •	 Shipping	weight	36	lbs.
 •	 Made	in	the	USA




                                                                                                              Cameron MD-70
          Cameron MD70-X with optional                                                                      Deep Throat Micro
            programmable Z axis and                                                                                Drill Press
               flat panel monitor

                                                                           Options Available:
                                                                           •	 Variable	Speed	Control	for	International	and		
                                                                              Domestic	use	240/120	V.AC	(5	amp)
                                                                           •	 Foot	Operated	Speed	Controls
                                                                           •	 Jacobs	5/32"	keytype	chuck	w/key
                                                                           •	 Yukiwa	0-1/8"	capacity	precision	keyless	chuck
                                                                           •	 Albrecht	0-1/8"	or	0-1/16"	capacity		
                                                                              precision	keyless	chucks
                                                                           •	 Hollow	spindles	for	special	applications
                                                                           •	 Table	column	stop
                                                                           •	 Chuck	wedges	for	easy	&	safe	removal	from	taper
                                                                           •	 Extended	columns	-	up	to	4"
                                                                           •	 Digital	Readout	indicator	and	slide	table
                                                                           •	 Programmable	Z	axis
           Cameron Variable Speed
         Control & On/Off Foot Switch
                                                                    Cameron MD-90 Micro Max
 Now… You can turn your                                            Milling Machine Adapter Unit
 Bridgeport milling
 machine (or similar mill) into
 an ultra-precision small-hole drilling unit.
 The	Cameron	Micro	Max	adapts	to	a	3/4"	collet	and	has	a	special	feature	to	lock	down	the		
 standard	3-3/8"	quill	to	the	1-7/8"	spindle	of	your	milling	machine.	This	special	lockdown	
 feature	prevents	the	spindle	from	turning.

 Combining	the	Cameron	Micro	Max	with	your	standard	milling	machine,	you	will	create	
 a	rigid	small-hole	drilling	unit	with	RPM	capabilities	up	to	30,000	RPM.

 The	Cameron	Micro	Max	and	the	X,	Y,	and	Z	movement	of	the	milling	
 machine	provide	endless	possibilities	in	achieving	outstanding		
 precision	work,	and	meeting	the	challenge	of	small	hole	drilling.

           Converts your mill into a precision
             small hole drilling instrument
                                                                                                                MD-90 Micro Max
                                                                                                     Milling Machine Adapter Unit


                                                Features:
                                                •	 The	Cameron	Micros	Max	MD-90	drills	small	holes	from	.002"	to	5/32"
                                                •	 Spindle	runout	is	within	.0001"	at	chuck	mounting	taper
                                                •	 Spindle	speeds	up	to	30,000	RPM
                                                •	 Spindle,	pulleys	and	motors	are	dynamically	balanced
                                                •	 Smooth	running,	long-lasting	AC/DC	motors	designed	and	manufactured	by	Cam-
                                                   eron	Micro	Drill	Presses
                                                •	 Single	Speed	Motors	Provide	RPM	settings	of	9,500	•	17,000	•	30,000	RPM
                                                •	 Variable	Speed	Control	available	for	international	and	domestic	use	240/120	V.AC		
                                                   (5	amp)
                                                •	 Dial	indicator	1/2"	travel
                                                •	 Clear	plastic	guard	for	easy	viewing	of	belt/pulley	position
                                                •	 Optional	columned	precision	ground	base	to	convert	Micro	Max	to	a	table	model
                                                •	 Made	in	the	USA




NEW! Cameron Manual Models
with Collet Spindles
 Features:                                       MD70-CS
 •	 30,000	RPM	Spindle                              (shown with
 •	 Less	than	1	um	Spindle	Run	Out                chuck adaptor)
 •	 Variable	Speed	Control
 •	 Flat	Belt
 •	 1/8"	and	1mm	Collet	Included                                                               MD90-CS
 •	 Drill	Small	Holes	from	5/32"	to	.002"                                                (shown with chuck adaptor)                     164-CS
 •	 Spindle	Feed	Travel:	1-1/4"                                                              and columned base
                                                                                                       Micro Drill Presses
                                                                                                                a division of Treat Enterprises, Inc.

               19401 Rawhide Road • Sonora, CA 95370 • Phone: 209-532-7201 • Fax: 209-532-1211


                                         27-28

                                                                          Micro Drill Press Parts List
                                53-54
                                              23-24

              29-31-32-33
                                                 30
                                                                      	 1.	 MD-101-7	 Head	(complete		              	33.	 MD-133-7	 Column	Lock	Screw	Lever
                                                                                      with	bearings)                	34.	 MD-134-7	 Table	Lock	Screw
                            8                           22            	 2.	 MD-102-7	 Column                        	35.	 MD-135-7	 Table	Lock	Screw	
                                                                      	 3.	 MD-103-7	 Table                                          Thumb	Lever
                                                                      	 4.	 MD-104-7	 Base                          	36.	 MD-136-7	 Motor	Mount
     51-54                                                   26       	 5.	 MD-105-7	 Rack                          	37.	 MD-137-7	 Knurled	Lock	Screw	
    21                                                                	 6.	 MD-106-7	 Pinion                        	38.	 MD-138-7	 Motor	Brushes	with		
                                                                      	 7.	 MD-107-7	 Pinion	Shaft                                   springs	(set	of	2)
                                                                      	 8.	 MD-108-7	 Oil	Hole	Fitting		            	39.	 MD-139-7	 Brush	Holders	with	caps	
     59                                                      25                       (Pinion	Shaft)                                 and	connectors	(set	of	2)
                                                                      	 9.	 MD-109-7	 Spoked	Feed	Wheel	Hub         	40.	 MD-140-7	 Motor	Bearings	with		
          1                                                           	10.	 MD-110-7	 Feed	Wheel	Lever	                              retainers	and	oil	felts
                                                              41-42
                                                                                      (threaded)                    	41.	 MD-141-7	 Motor	Case	Section		
                                                                      	11.	 MD-111-7	 Feed	Wheel	Lever	(grooved)                     (pulley	end)
              5-6-7                                          48-49    	12.	 MD-112-7	 Return	Spring                 	42.	 MD-142-7	 Motor	Case	Section	
                                                                      	13.	 MD-113-7	 Return	Spring	Clamp	Ring                       (brush	holder	end)
                                                             38-39
    15-16-17-18                                                       	14.	 MD-114-7	 Slotted	Spring	Tension	       	43.	 MD-143-7	 Armature
       19-20-58                                                                       Adjuster                      	44.	 MD-144-7	 Field	Assembly
                                                          40-43-44    	15.	 MD-115-7	 Spindle                       	45.	 MD-145-1	 Switch	for	single		
                                                          45-46-47    	16.	 MD-116-7	 Set	of	Spindle	Bearings	                       speed	motor
     55-56-57
                                             9-12-13-14                               factory	installed	(send		     	46.	 MD-145-2	 Switch	for	two		
                                                                                      drill	press	head	only	to		                     speed	motor
          2                                     10-11                                 factory	where	new	spindle		   	47.	 MD-146-7	 Electric	Cord
                                                                                      bearings	will	be	installed	   	48.	 MD-147-1	 Motor	(single	speed		
     3                                                                                and	head	returned		                            with	switch	and	cord)
                                                34-35                                 promptly	to	sender            	49.	 MD-147-2	 Motor	(two	speed	with	
                                                                      	17.	 MD-117-7	 Half	Rings	for	Spindle		                       switch	and	cord)
                                                                                      (set	of	2)                    	50.	 MD-148-7	 Screws	(complete	set		
                                                                      	18.	 MD-118-7	 Half	Ring	Retainer	for		                       for	drill	press	and	motor)
                                                                                      above	Hal	Rings               	51.	 MD-149-7	 Oil	hole	plugs	for	drill	press	
                                                                      	19.	 MD-119-7	 Thrust	Bearing	Assembly	                       Head	(set)
                                                                                      (spindle	upper)               	52.	 MD-150-7	 V-Belt
4                                                                     	20.	 MD-120-7	 Thrust	Bearing	Assembly	      	53.	 MD-151-7	 Dial	Indicator
                                                                                      (spindle	lower)               	54.	 MD-152-7	 Attachments	for	Mounting	
                                                                      	21.	 MD-121-7	 Pulley	(spindle)                               Dial	Indicator	on	Drill	Press
                                        50                            	22.	 MD-122-7	 Pulley	(motor)                	55.	 MD-153-7	 Jacobs	Geared	Chuck	with	
                                                                      	23.	 MD-123-7	 Knurled	Depth	Stop		                           Key	(5/32"	capacity)
                                                                                      Nuts	(set	of	2)               	56.	 MD-154-7	 Albrecht	Keyless	Chuck		
          Cameron Series 164                                          	24.	 MD-124-7	 Depth	Stop	(column	end		                       (0	to	1/16"	capacity)
           Micro Drill Press                                                          nut		abutment	casting)        	57.	 MD-155-7	 Albrecht	Keyless	Chuck		
                                                                      	25.	 MD-125-7	 Motor	resister	for	low	                        (0	to	1/8"	capacity)
                                                                                      speed	switch	position		       	58.	 MD-156-7	 Spindle	with	Spindle		
                                                                                      of	two	speed	motor                             Pulley	as	a	Matched	and	
                                                                      	26.	 MD-126-7	 Head	Raising	Stop		                            Balanced	Assembly
                                                                                      Bumper	(resilient	plastic)    	59.	 MD-157-7	 Guard
                                                                      	27.	 MD-127-7	 Depth	Stop	Stem	(for	         	60.	 MD-158-7	 Chuck	Wedges
                Cameron                                                               machine	without	indicator)    	61.	 MD-159-2A	 Cameron	International		
                                                                      	28.	 MD-128-7	 Depth	Stop	Stem	and	                           VSC	240/120	V.AC
              MD-90 Micro                                                             Indicator	Post                	62.	 MD-159-FS	 Foot	Switch	(international)	
               Max with                                               	29.	 MD-129-7	 Indicator	Adjustment	                          for	Cameron	VSC	Unit
                                                                                      Bracket                       	63.	 MD-160-7	 Jacobs	1/4"	Keytype	Chuck
               Precision                                              	30.	 MD-130-7	 Knurled	Clamp	Screw	          	64.	 MD-161-7	 Precision	Table		
              Ground Base                                                             for	Indicator	Adjustment	                      Column	Stop
                                                                                      Bracket                       	65.	 MD-162-7	 Reservoir	Base		
                                                                      	31.	 MD-131-7	 Column	Lock	Screw                              for	Series	164
                                                                      	32.	 MD-132-7	 Column	Lock	Screw	Pad         	66.	 MD-163-7	 ChuckGuard




1-800-369-7769 • www.cameronmicrodrillpress.com

				
DOCUMENT INFO
Shared By:
Categories:
Tags:
Stats:
views:0
posted:7/21/2013
language:Unknown
pages:4
jny jhtw jny jhtw
About