Docstoc

TL1120

Document Sample
TL1120 Powered By Docstoc
					                                                                INSTRUCTIONS                                                                                        INSTRUCTIONS

Introduction                                                                                      Configuration
Congratulations on your purchase of the Competition Pro TL-1120 subwoofer enclosure. The          The TL-1121 subwoofer comes with dual 2 ohm voice coils. This enables the user/installer
TL-1120 is not simply a generic box enclosure. After a lot of research, design, development       to connect one TL-1121 subwoofer to an amplifier in either of the following two ways:
and testing, TheLoudest.com are able to present a revolutionary enclosure designed for the
TL-1121 subwoofer.                                                                                   1. Parallel – Recommended (See diagram below).
                                                                                                        - Install both jumper connectors (included) to the terminal block on the side of the
The most impressive feature is the interchangeable section on the front of the enclosure.               enclosure.
For every day-listening, the blanking plate can be installed; this enables the TL-1120 to               - Connect the top – (black) and + (red) pair on the enclosure terminal block to the
function as a sealed enclosure, resulting in high fidelity reproduction by the subwoofer, over          left terminal pair on the subwoofer (black to black and red to red).
the entire bass frequency range. This suits most types of music, giving audiophile quality              - Connect the bottom – (black) and + (red) pair on the enclosure terminal block to
sound.                                                                                                  the right terminal pair on the subwoofer (black to black and red to red).
                                                                                                        - Connect one of the – (red) terminals on the side of the enclosure to the – terminal
For extreme listening or SPL competitions, installing the port plate into the interchangeable           on the amplifier.
section on the front of the enclosure transforms the TL-1120 into a ported enclosure,                   - Connect one of the + (black) terminals on the side of the enclosure to the +
unlocking the full potential of the woofer, resulting in pure subsonic power of monstrous               terminal on the amplifier.
proportions, ensuring the TL-1121 hits the hardest, deepest and loudest bass, blowing away
                                                                                                                               Terminal block on side
just about anything that dares to stand in its path.
                                                                                                        “jumper” connector      of TL-1120 enclosure
                                                                                                                                                         TL-1121       If mounting woofer inside
Other impressive features include the stylish black-vinyl finish, substantially re-enforced
                                                                                                                                                        subwoofer      enclosure, use already
design, protective steel rods (included for optional mounting), and the option to mount the
                                                                                                                                                                       installed internal cables.
woofer on the outside facing inwards.                                                                                                                                  If mounting woofer outside
                                                                                                             TL-1022
                                                                                                            amplifier                                                  enclosure pointing inwards,
This means that the TL-1120 functions as either a sealed or ported enclosure, looks elegant                 terminals                                                  connect to the external
and is flexible enough to be installed into a vehicle boot also used for transporting items                                                                            connections on the terminal
(woofer mounted inside the enclosure, with the protective steel bars installed) or into a                   1 ohm load to                                              block as illustrated here.
                                                                                                                                                    Dual 2 ohm voice
vehicle boot dedicated to in car entertainment (woofer mounted on the outside of the                          amplifier
                                                                                                                                                     coil subwoofer
enclosure, facing inwards).

It is imperative that you read through these instructions before installing and operating the        2. Series – Not Recommended (See diagram below).
subwoofer with this enclosure. This will ensure correct configuration and operation. While              - Install one of the jumper connectors to the right terminals on the terminal block, on
these instructions detail generally how to install the enclosure, if you do not have sufficient         the side of the enclosure.
experience or tools, it is best to have it professionally installed.                                    - Connect the top – (black) and + (red) pair on the enclosure terminal block to the
                                                                                                        left terminal pair on the subwoofer (black to black and red to red).
Keep this manual in a safe place so it is accessible for future reference.                              - Connect the bottom – (black) and + (red) pair on the enclosure terminal block to
                                                                                                        the right terminal pair on the subwoofer (black to red and red to black).
Dimensions                                                                                              - Connect the left two terminals on the terminal block to the amplifier, one to - and
                                                                          Port plate                    the other to +.
                                                                                                                               Terminal block on side
                                              55 cm                            Blanking plate                                   of TL-1120 enclosure
                           43 cm
                                                                                                                                                         TL-1121       If mounting woofer inside
                                                                                                        “jumper” connector                              subwoofer      enclosure, use already
                                                                                                                                                                       installed internal cables.
              40.8 cm                                                                                        TL-1022                                                   If mounting woofer outside
                                                                41.2 cm                                     amplifier                                                  enclosure pointing inwards,
                                                                                                            terminals                                                  connect to the external
  Terminal block                                                                                                                                                       connections on the terminal
                                                                                                            4 ohm load to                                              block as illustrated here.
                                                                                                                                                    Dual 2 ohm voice
                                                                                                              amplifier
                                                                                                                                                     coil subwoofer

                           49 cm



55 cm (Width) x 40.8 cm (Height) x 49 cm (Depth).
Length (not height) of front: 41.2 cm. Depth at top: 43 cm.
                                                                                                  Œ

				
DOCUMENT INFO
Shared By:
Categories:
Tags:
Stats:
views:1
posted:4/11/2013
language:Latin
pages:2