1344049_ac0245750

Document Sample
1344049_ac0245750 Powered By Docstoc
					     PA9T:[Genestar]玻璃纤维增强难燃级的物性
                                   试验方法
                          单位                    G2330    G2450
                                    ASTM
玻璃纤维含量                     %         ─           33       45
基本物性
比重                                               1.68    1.77
吸水率(23℃水中)
                           %        D570         0.08    0.08
24小时3mmt
耐燃性                        ─        UL94         V-0      V-0
机械性能
                 决干                               160      190
伸张强度                      MPa       D638
                (吸湿)                            (170)    (185)
                 决干                               3.0      2.7
伸张延伸率                      %        D638
                (吸湿)                             (3.0)    (2.7)
                 决干                               240      260
弯曲强度                      MPa       D790
                (吸湿)                            (230)    (255)
                 决干                              11.0     14.0
弹性模数                      GPa       D790
                (吸湿)                            (11.0)   (14.0)
                 决干                               110      105
IZOD冲击强度                  J/m       D256
                (吸湿)                            (110)    (105)
洛氏硬度                     R Scale    D785          125      125
温度特性
融点                         ℃         ─           306      306
玻璃转移点                      ℃         ─           125      125
热变形温度 1.82MPa              ℃         ─           285      285
电气特性
绝缘破坏强度                   MV/m        D149        38       38
体积固有阻抗                   Ω.cm        D257        10
                                                   16
                                                          10
                                                            16

耐电弧强度                     V        IEC-CTI       550      550
诱电率(1MHz)                 ─          D150        3.7      3.7
诱电正接(1MHz)                ─          D150       0.014    0.014
尺寸特性
成型收缩率            ∥         %                     0.4      0.3
                                     ─
                 ⊥         %                     0.9      0.7
线膨胀系数            ∥         %                     2.5      2.3
                                     ─
                 ⊥         %                     4.0      3.0




                           深圳市立来兴实业有限公司
                           0755-27368166 27368266
                       http://lilaixing.cn.alibaba.com
GRADES AND PHYSICAL PROPERTIES
                                                 ARLEN
                              C/Eseries   (For electrical and electronic parts)
                                                     Test method
Physical properties                         Unit                    C430          E430N        CH230N
                                                       ASTM
Glass fiber content                          %           ─           30            30             30
Specific gravity                             ─          D792        1.66          1.66           1.63


Mechanical properties★1
Tensile strength                            MPa         D638         170           170           160
                                                             ★2
Tensile elongation                           %        D638            3             3                4
Flexural strength                           MPa        D790          250           250           240
Flexural modulus                            MPa        D790         11400         11400         11000
Izod impact strength      (notched)         J/m        D256          85            80            80
Rockwell hardness                          Mscale      D785          95            100           95

Thermal properties
Melting point                                ℃           ─           310           320           310
Glass transition point                       ℃           ─           85            95            85
Deflection temp.             under
                                             ℃          D648         295           305           290
load(1.82MPa)
Coefficient of Flow direction linear
                                                                     1.2           2.2           1.5
thermal                      expansion    ×10-5/℃     E831-93
                                                                     9.2           7.3           8.9
Vertical direction
Flammability                                 ─         UL 94        V-0            V-0           V-0


Electrical properties★1
Volume resistivity                          Ω.cm        D257        1015           1015          1015
Dielectric constant(106Hz)                   ─          D150         4.0           3.6           4.0
Dielectric dissipation factor(106Hz)         ─          D150        0.013         0.012         0.013
Dielectric breakdown voltage               KV/mm        D149         26            24                25

Mold shrinkage(2mmt)
Flow diretion                                %          D955         0.3           0.3           0.4
Vertical direction                           %          D955         0.7           0.9           0.8


Reflow soldering test★3
Water absorption★4                           %          D570         2.0           1.9           2.2
Peak Temperature
                                             ℃      Mitsui Method   240★5         250★5         240★5
under feflow soldering test
Notes:
★ The above figures are just representative values but not specification values.
★1 Specimen was in the dry condition
★2 Elongation was measured between the chucks.
★3 The Size of Specimen:64L×6W×0.8Tmm
★4 Moist:In a saturated state in the atmosphere at 23℃ and a relative humidity of 65%
★5 Heat resistance under a reflow soldering process depends on the dimension of the
   products and the reflow conditions.

                                             深圳市立来兴实业有限公司 0755-27368166                   27368266
http://lilaixing.cn.alibaba.com
MITSUI CHEMICALS
                                                                                          P           E             S
                                                                                        Poly        Ether Sulphone

Typical Grade
                                                     Grade               Feature                                             Filler
GF Reinforced                                        SGN3030R            Standard,Mold Release                                  GF30%
                                                     SGN2020R            High Flowability,Mold Release                          GF20%
                                                     SGN2030R            High Flowability,Mold Release                          GF30%
                                                     SGP2020R            Super High Flowability,Mold Release                    GF20%

                                                     SGF2030             Low Friction,Low Abrasion                        GF20%,PTFE
                                                     SGF2040             Low Abrasion,High strength                       GF21%,PTFE
Packaging:Pellet/25KG




Properties
                                                                          Grade Name SGN3030R      SGN2020R      SGP2020R     SGF2030
                                                                                                      High       Ultra-High
                                                                         Main Feature   Standard                             Wear Friction
                                                                                                   Flowability   Flowability
                                                                              Filler      GF           GF            GF          GF
                                                               Filler Content(wt%)        30           20            20           30
                 Items                                Test Method         Unit
Physical         Specific Gravity                     ASTM D-792                         1.60         1.51          1.51         1.57
Properties       Water Absorption                     ASTM D-570           %              0.5          0.6           ─            ─
                 Molding ShrinkageMD/TD               ASTM D-955           %            0.2/0.6      0.2/0.6       0.3/0.6      0.3/0.6

Mechanical       Tensile Strength                     ASTM D-638              MPa        137          127           130           127
Properties       Elongation                           ASTM D-638               %          3            3             3             3
                 Tensile Modulus                      ASTM D-638              MPa        9800         6800
                 Flexural Strength                    ASTM D-790              MPa        190          167          179           181
                 Flexural Modulus                     ASTM D-790              MPa        8800         6700         7400          7400
                 Izod Impact Strength                 ASTM D-256              J/m         90           60           80            90
                 Rockwell Hardness                    ASTM D-648                         M98          M98

Thermal          HDT                                  ASTM D-648              ℃           217          214           215          216
Properties       Linear Thermal Expansion             ASTM D-696            ×10-5/C     1.6/5.6      2.6/5.6       2.4/5.5      1.9/5.4

Other            Volume Resistivity                   ASTM D-257             Ω.cm        >1016       >1016         >1016         >1016

Properties       Coefficient of Kinetic Friction             ─                            ─            ─             ─         0.15-0.25

                 Flame Retardancy 0.4mm                    UL94                           V-0         V-0            ─            ─
                 Limiting Oxygen Index
                                                     ASTM D-286TM                         41           40            ─            ─
                 1.6mm

Notes:The Above figures are just representative value,but not specification values.
深圳市立来兴实业有限公司         0755-27368166   27368266
       http://lilaixing.cn.alibaba.com

				
DOCUMENT INFO
Shared By:
Categories:
Tags:
Stats:
views:3
posted:1/4/2013
language:Unknown
pages:5