Docstoc

Martin Yale WRA163313 Top Blade Replacement For The 1632 Letter Opener Data Sheet

Document Sample
Martin Yale WRA163313 Top Blade Replacement For The 1632 Letter Opener Data Sheet Powered By Docstoc
					http://www.monomachines.com/


                                          For More Info

                                          Click Here --->



                                             1632 Top Blade Replacement

                                      * Unplug the unit before performing this procedure

                               Replacement Part Number W-A163313 Top Blade/Guide Assembly

                                         Includes: 1) MRO163232 Blade Guide
                                                   1) MRO163233 Top Blade Assembly
                                                   1) MRO163234 Top Blade Spring
                                                   1) MRO163235 ¼” Ball Bearing




                ________________________________________________________________________________




                                          1. Remove Top Cover from the unit.
                ________________________________________________________________________________




                                                                                                   Page 1




http://www.monomachines.com/
http://www.monomachines.com/

                                                                          For More Info

                                                                           Click Here --->




                               2. Turn unit over and remove 3) screws from the Bottom Housing
                ________________________________________________________________________________




                    3. Turn unit back over and remove 7) screws from the Top Deck. Note the plastic
                       strap located above the screwdriver as shown in picture. Do Not Lose!

                  ________________________________________________________________________________




                                             4. Remove Top Deck from unit.
                ________________________________________________________________________________
                                                                                                      Page 2




http://www.monomachines.com/
http://www.monomachines.com/
                                                                              For More Info

                                                                              Click Here --->




                           5. Loosen the set screw one or two full revolutions in the Drive Pulley.
                ________________________________________________________________________________




                                      6. Remove 2) screws from the Top Blade Guide.
                ________________________________________________________________________________




                       7. Remove Top Blade Guide. This guide contains a ball and a spring inside.
                ________________________________________________________________________________

                                                                                                      Page 3




http://www.monomachines.com/
http://www.monomachines.com/



                                                  For More Info

                                                  Click Here --->




                    8. Lift the Main Frame from the blade end and separate from Bottom Housing.
                ________________________________________________________________________________




                    9. Pull Lower Blade Assembly away from the Main Frame to permit Top Blade
                       removal. Do not lose the ball bearing from the end of the shaft.
                _________________________________________________________________________________




                                                                                                    Page 4




http://www.monomachines.com/
http://www.monomachines.com/




                                     For More Info

                                     Click Here --->




                   10. Carefully remove the Top Blade from the Main Frame. BLADE IS SHARP
                       and can cause injury if handled carelessly. Dispose of properly.
                       Install the new Top Blade in the same position in the Main Frame.
                ________________________________________________________________________________




                   11. Push Lower Blade Assembly back fully into the Main Frame and position Drive
                       Pulley set screw over flat on shaft. Securely tighten set screw into the flat on shaft.
                       Note: Top Blade should be located between the Lower Blade and the Main Frame.
                ________________________________________________________________________________




                                                                                                                 Page 5




http://www.monomachines.com/
http://www.monomachines.com/




                                            For More Info

                                             Click Here --->




                         12. Replace Main Frame back into position in the Bottom Housing.
                        Be sure the shaft bearing is secure in Bottom Housing as shown at left.
                ________________________________________________________________________________




                    13. Carefully place the Top Blade Guide (including spring and ball installed) onto the
                        Top Blade shaft and compress the Blade and Guide as shown. Install the 2) screws
                        to secure the Top Blade Guide. NOTE: Use small amount of light machine oil to
                        lubricate blade shaft and inside blade guide before assembly.
                ________________________________________________________________________________




                                                                                                             Page 6




http://www.monomachines.com/
http://www.monomachines.com/




                                            For More Info

                                            Click Here --->




                     14. Replace Top Deck into position in the Bottom Housing. Do Not Forget to place the
                         plastic strap into position as it was before it was removed in Step 3. Reinstall the 7)
                         deck screws to secure the Top Deck to the Bottom Housing. Make sure the plastic
                         strap is positioned over the microswitch lever as shown in right photo.
                ________________________________________________________________________________




                     15. Replace Top Cover onto the Bottom Housing. Be sure the Main Frame is properly
                         positioned to permit Top Cover to fit onto the Bottom Housing completely.
                ________________________________________________________________________________




                                                                                                                   Page 7



http://www.monomachines.com/
http://www.monomachines.com/




                                       For More Info

                                       Click Here --->




                    16. Turn unit over and securely reinstall 3) screws into the Top Cover as shown.
                ________________________________________________________________________________




                     17. Snap the Top Cover into place. Plug cord into receptacle and unit should operate
                         when switched on. If unit does not turn on, refer to Step 14 and strap location on
                         microswitch lever.
                 ________________________________________________________________________________




                                                                                                              Page 8




http://www.monomachines.com/

				
DOCUMENT INFO
Shared By:
Stats:
views:12
posted:12/5/2012
language:
pages:8
Description: Martin Yale Top Blade Replacement For The 1632 Letter Opener - WRA163313